Kernel-build-reports April 2014

kernel-build-reports@lists.linaro.org

20 participants
319 discussions

mainline build: 8 warnings 0 failures (mainline/v3.14-8411-gf7789dc)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was mainline, found at: http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git (master branch) Topmost commit: f7789dc Merge branch 'locks-3.15' of git://git.samba.org/jlayton/linux Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/mainline/v3.14-8411-gf7789dc/ Runtime: 41m 55s Passed: 123 Failed: 0 Warnings: 8 Section mismatches: 0 ------------------------------------------------------------------------------- Failed defconfigs: ------------------------------------------------------------------------------- Errors: Warnings: 1 drivers/mfd/sec-core.c:342:45: warning: 'regmap_rtc' may be used uninitialized in this function [-Wmaybe-uninitialized] 1 drivers/usb/host/xhci-plat.c:206:12: warning: 'xhci_plat_suspend' defined but not used [-Wunused-function] 1 drivers/usb/host/xhci-plat.c:214:12: warning: 'xhci_plat_resume' defined but not used [-Wunused-function] 1 net/netfilter/xt_connlimit.c:380:45: warning: division by zero [-Wdiv-by-zero] 2 buildall.arm.multi_lpae_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) 2 buildall.arm.multi_v7_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) Section mismatches:

10 years, 8 months

queue boot: 19 pass, 0 fail (v3.10.36)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: queue Git describe: v3.10.36 Full Report =========== da8xx_omapl_defconfig --------------------- da850-evm 0 min 14.8 sec: PASS legacy,da850evm 0 min 13.9 sec: PASS omap2plus_defconfig ------------------- legacy,3730xm 0 min 49.5 sec: PASS omap3-beagle-xm 1 min 3.0 sec: PASS legacy,3530beagle 0 min 36.1 sec: PASS omap4-panda 1 min 7.0 sec: PASS omap3-tobi 0 min 33.8 sec: PASS am335x-bone 0 min 26.4 sec: PASS omap4-panda-es 1 min 10.8 sec: PASS legacy,3730storm 0 min 52.7 sec: PASS legacy,3530overo 0 min 21.1 sec: PASS tegra_defconfig --------------- tegra30-beaver 0 min 14.8 sec: PASS imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual 0 min 17.3 sec: PASS imx6dl-wandboard,wand-solo 0 min 17.3 sec: PASS mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 0 min 21.6 sec: PASS armada-370-mirabox 0 min 19.6 sec: PASS exynos_defconfig ---------------- exynos5250-arndale 0 min 36.9 sec: PASS sama5_defconfig --------------- sama5d35ek 0 min 16.4 sec: PASS davinci_all_defconfig --------------------- legacy,dm365evm 0 min 16.5 sec: PASS

10 years, 8 months

mainline boot: 46 pass, 0 fail (v3.14-8380-g3c83e61)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: mainline Git describe: v3.14-8380-g3c83e61 Full Report =========== da8xx_omapl_defconfig --------------------- da850-evm 0 min 15.5 sec: PASS (Warnings: 1) legacy,da850evm 0 min 14.4 sec: PASS (Warnings: 1) omap2plus_defconfig ------------------- legacy,3730xm 0 min 55.2 sec: PASS am335x-boneblack 0 min 25.7 sec: PASS omap3-beagle-xm 1 min 1.4 sec: PASS legacy,3530beagle 0 min 35.7 sec: PASS (Warnings: 1) omap4-panda 1 min 11.9 sec: PASS omap3-overo-tobi 0 min 23.3 sec: PASS (Warnings: 1) am335x-bone 0 min 32.4 sec: PASS omap3-overo-storm-tobi 0 min 22.6 sec: PASS omap5-uevm 1 min 2.6 sec: PASS (Warnings: 1) omap4-panda-es 1 min 14.6 sec: PASS legacy,3730storm 0 min 20.5 sec: PASS legacy,3530overo 0 min 21.0 sec: PASS (Warnings: 1) multi_lpae_defconfig -------------------- omap5-uevm 1 min 50.5 sec: PASS (Warnings: 1) sun7i-a20-cubieboard2 0 min 14.4 sec: PASS tegra_defconfig --------------- tegra30-beaver 0 min 30.5 sec: PASS imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual 0 min 18.5 sec: PASS imx6dl-wandboard,wand-solo 0 min 18.8 sec: PASS imx6q-wandboard 0 min 16.9 sec: PASS msm_defconfig ------------- qcom-apq8074-dragonboard 0 min 14.3 sec: PASS bcm_defconfig ------------- bcm28155-ap 0 min 23.2 sec: PASS sunxi_defconfig --------------- sun7i-a20-cubieboard2 0 min 13.6 sec: PASS sun4i-a10-cubieboard 0 min 13.1 sec: PASS exynos_defconfig ---------------- exynos5250-arndale 0 min 29.6 sec: PASS multi_v7_defconfig ------------------ tegra30-beaver 0 min 17.2 sec: PASS am335x-boneblack 0 min 23.6 sec: PASS omap3-beagle-xm 0 min 45.0 sec: PASS sun7i-a20-cubieboard2 0 min 14.5 sec: PASS armada-370-mirabox 0 min 22.0 sec: PASS omap4-panda 0 min 51.6 sec: PASS armada-xp-openblocks-ax3-4 0 min 25.9 sec: PASS sun4i-a10-cubieboard 0 min 14.5 sec: PASS bcm28155-ap 0 min 27.6 sec: PASS omap3-overo-tobi 0 min 22.2 sec: PASS (Warnings: 1) imx6dl-wandboard,wand-solo 0 min 18.4 sec: PASS am335x-bone 0 min 26.2 sec: PASS omap3-overo-storm-tobi 0 min 21.1 sec: PASS omap5-uevm 1 min 47.1 sec: PASS (Warnings: 1) imx6q-wandboard 0 min 17.3 sec: PASS omap4-panda-es 0 min 59.2 sec: PASS imx6dl-wandboard,wand-dual 0 min 18.4 sec: PASS sama5_defconfig --------------- sama5d35ek 0 min 17.0 sec: PASS davinci_all_defconfig --------------------- legacy,dm365evm 0 min 17.3 sec: PASS mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 0 min 21.9 sec: PASS armada-370-mirabox 0 min 20.1 sec: PASS

10 years, 8 months

mainline boot: 29 passed 4 failed (mainline/v3.14-8380-g3c83e61)

by Olof's autobooter

Failed boards: dalmore tegra_defconfig : FAILED 1:28.55 dalmore multi_v7_defconfig : FAILED 1:05.33 dalmore multi_lpae_defconfig : FAILED 1:05.13 panda multi_v7_defconfig : FAILED 1:34.59 Successful boards: apc vt8500_v6_v7_defconfig : passed 1:18.62 arndale exynos_defconfig : passed 1:02.91 bbb omap2plus_defconfig : passed 1:30.77 bbb multi_v7_defconfig : passed 1:28.91 beaver tegra_defconfig : passed 0:53.68 beaver multi_v7_defconfig : passed 0:49.70 capri bcm_defconfig : passed 0:43.97 capri multi_v7_defconfig : passed 0:44.32 cubie sunxi_defconfig : passed 1:03.35 cubie multi_v7_defconfig : passed 1:21.68 cubie2 sunxi_defconfig : passed 1:03.98 cubie2 multi_v7_defconfig : passed 1:10.49 cubie2 multi_lpae_defconfig : passed 1:03.59 cubox dove_defconfig : passed 0:56.91 hummingboard imx_v6_v7_defconfig : passed 1:16.66 hummingboard multi_v7_defconfig : passed 1:11.65 omap5uevm multi_v7_defconfig : warnings 1:36.64 omap5uevm multi_lpae_defconfig : warnings 1:35.24 panda omap2plus_defconfig : passed 1:14.98 sama5 sama5_defconfig : passed 1:51.38 seaboard tegra_defconfig : passed 1:01.87 seaboard multi_v7_defconfig : passed 1:08.04 snow exynos_defconfig : passed 1:23.79 snowball u8500_defconfig : passed 1:27.40 snowball multi_v7_defconfig : passed 2:05.56 trimslice tegra_defconfig : passed 1:00.61 trimslice multi_v7_defconfig : passed 1:11.40 wandboard imx_v6_v7_defconfig : passed 0:56.40 wandboard multi_v7_defconfig : passed 1:08.27 Offline boards: omap5uevm omap2plus_defconfig : OFFLINE 2:30.19 Board legend is available at http://arm-soc.lixom.net/boards.html Last entries of failed logs below: ======================================================================== Board dalmore-multi_lpae_defconfig failure log: ------------------------------------------------- Tegra114 (Dalmore) # tftp 0x82000000 mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/zImage tftp 0x82000000 mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/zImage Using asx0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.138 Filename 'mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################# 2.8 MiB/s done Bytes transferred = 4524472 (4509b8 hex) Tegra114 (Dalmore) #setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 Tegra114 (Dalmore) # tftp 0x83000000 mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/dtbs/tegra114-dalmore.dtb tftp 0x83000000 mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/dtbs/tegra114-dalmore.dtb Using asx0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.138 Filename 'mainline/v3.14-8380-g3c83e61/multi_lpae_defconfig/dtbs/tegra114-dalmore.dtb'. Load address: 0x83000000 Loading: *### 2.5 MiB/s done Bytes transferred = 34059 (850b hex) Tegra114 (Dalmore) # printenv bootargs printenv bootargs bootargs=console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait debug earlyprintk Tegra114 (Dalmore) # bootz 0x82000000 - 0x83000000 bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x4509b8 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 8fff4000, end 8ffff50a ... OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board dalmore-multi_v7_defconfig failure log: ------------------------------------------------- Tegra114 (Dalmore) #tftp 0x82000000 mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/zImage tftp 0x82000000 mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/zImage Using asx0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.138 Filename 'mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################### 2.8 MiB/s done Bytes transferred = 4501328 (44af50 hex) Tegra114 (Dalmore) #setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 Tegra114 (Dalmore) # tftp 0x83000000 mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/dtbs/tegra114-dalmore.dtb tftp 0x83000000 mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/dtbs/tegra114-dalmore.dtb Using asx0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.138 Filename 'mainline/v3.14-8380-g3c83e61/multi_v7_defconfig/dtbs/tegra114-dalmore.dtb'. Load address: 0x83000000 Loading: *### 2.5 MiB/s done Bytes transferred = 34059 (850b hex) Tegra114 (Dalmore) # printenv bootargs printenv bootargs bootargs=console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait debug earlyprintk Tegra114 (Dalmore) # bootz 0x82000000 - 0x83000000 bootz 0x82000000 - 0x83000000 Kernel image @ 0x82000000 [ 0x000000 - 0x44af50 ] ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Device Tree to 8fff4000, end 8ffff50a ... OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board dalmore-tegra_defconfig failure log: ------------------------------------------------- [ 1.076689] avdd-usb: 3300 mV [ 1.078685] avdd-usb: supplied by vdd-sys-5v0 [ 1.084852] rail-3v3: no parameters [ 1.088765] rail-5v0: no parameters [ 1.092329] REGEN3: no parameters [ 1.095282] SYSEN1: no parameters [ 1.098813] SYSEN2: no parameters [ 1.103908] Linux video capture interface: v2.00 [ 1.110444] platform 70019010.iommu: Driver tegra-smmu requests probe deferral [ 1.117393] Advanced Linux Sound Architecture Driver Initialized. [ 1.127252] Bluetooth: Core ver 2.19 [ 1.129363] NET: Registered protocol family 31 [ 1.133535] Bluetooth: HCI device and connection manager initialized [ 1.140059] Bluetooth: HCI socket layer initialized [ 1.144939] Bluetooth: L2CAP socket layer initialized [ 1.150267] Bluetooth: SCO socket layer initialized [ 1.157542] cfg80211: Calling CRDA to update world regulatory domain [ 1.164352] Switched to clocksource arch_sys_counter [ 1.252370] NET: Registered protocol family 2 [ 1.258810] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.264479] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.271192] TCP: Hash tables configured (established 8192 bind 8192) [ 1.278667] TCP: reno registered [ 1.280288] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.286438] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.293954] NET: Registered protocol family 1 [ 1.299739] RPC: Registered named UNIX socket transport module. [ 1.303859] RPC: Registered udp transport module. [ 1.308689] RPC: Registered tcp transport module. [ 1.313393] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.319957] PCI: CLS 0 bytes, default 64 [ 1.339983] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 1.348682] bounce pool size: 64 pages [ 1.356418] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.363449] msgmni has been set to 1468 [ 1.371426] io scheduler noop registered (default) [ 1.404252] tegra114-pinctrl 70000868.pinmux: Config param 000e not supported on group drive_gma [ 1.411310] tegra114-pinctrl 70000868.pinmux: pin_config_group_set op failed for group 199 [ 1.419616] tegra114-pinctrl 70000868.pinmux: Error applying set~$off # PYBOOT: Exception: timeout ======================================================================== Board panda-multi_v7_defconfig failure log: ------------------------------------------------- [ 1.608306] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.615051] usbcore: registered new interface driver usbhid [ 1.620880] usbhid: USB HID core driver [ 1.628295] TCP: cubic registered [ 1.631805] NET: Registered protocol family 17 [ 1.636596] Key type dns_resolver registered [ 1.641540] Power Management for TI OMAP4+ devices. [ 1.646667] Power Management for TI OMAP4. [ 1.650939] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.658020] Registering SWP/SWPB emulation handler [ 1.664459] vwl1271: 1800 mV [ 1.669342] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.678527] twl 0-0048: PIH (irq 39) nested IRQs [ 1.684173] twl_rtc rtc.11: Power up reset detected. [ 1.691345] twl_rtc rtc.11: Enabling TWL-RTC [ 1.698059] twl_rtc rtc.11: rtc core: registered rtc.11 as rtc0 [ 1.705169] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.711273] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.717376] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.723480] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.728973] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.734374] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.739379] VDAC: 1800 mV [ 1.743103] VANA: 2100 mV [ 1.746612] VCXIO: 1800 mV [ 1.749694] VUSB: 3300 mV [ 1.753570] V1V8: 1800 mV [ 1.757110] V2V1: 2100 mV [ 1.763122] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.888458] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.040252] hub 1-1:1.0: USB hub found [ 2.044830] hub 1-1:1.0: 5 ports detected [ 2.061340] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.284667] gic_timer_retrigger: lost localtimer interrupt [ 2.369384] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.394195] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.510223] smsc95xx v1.0.4 [ 2.589263] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, 0a:8b:3a:44:a7:09 ~$off # PYBOOT: Exception: timeout

10 years, 8 months

arm-soc boot: 45 pass, 0 fail (v3.14-9179-gc2ef127)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: arm-soc Git describe: v3.14-9179-gc2ef127 Full Report =========== omap2plus_defconfig ------------------- legacy,3730xm 0 min 47.6 sec: PASS am335x-boneblack 0 min 25.5 sec: PASS omap3-beagle-xm 1 min 1.3 sec: PASS legacy,3530beagle 0 min 36.0 sec: PASS (Warnings: 1) omap4-panda 1 min 13.1 sec: PASS omap3-overo-tobi 0 min 23.7 sec: PASS (Warnings: 1) am335x-bone 0 min 32.9 sec: PASS omap3-overo-storm-tobi 0 min 22.5 sec: PASS omap5-uevm 1 min 3.0 sec: PASS (Warnings: 1) omap4-panda-es 1 min 15.0 sec: PASS legacy,3730storm 0 min 23.4 sec: PASS legacy,3530overo 0 min 21.2 sec: PASS (Warnings: 1) multi_lpae_defconfig -------------------- omap5-uevm 1 min 48.4 sec: PASS (Warnings: 1) sun7i-a20-cubieboard2 0 min 12.0 sec: PASS tegra_defconfig --------------- tegra30-beaver 0 min 17.2 sec: PASS imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual 0 min 18.9 sec: PASS imx6dl-wandboard,wand-solo 0 min 19.2 sec: PASS imx6q-wandboard 0 min 17.2 sec: PASS sunxi_defconfig --------------- sun7i-a20-cubieboard2 0 min 22.5 sec: PASS sun4i-a10-cubieboard 0 min 18.2 sec: PASS bcm_defconfig ------------- bcm28155-ap 0 min 22.9 sec: PASS mvebu_v7_defconfig ------------------ armada-xp-openblocks-ax3-4 0 min 22.4 sec: PASS armada-370-mirabox 0 min 20.3 sec: PASS exynos_defconfig ---------------- exynos5250-arndale 0 min 29.7 sec: PASS multi_v7_defconfig ------------------ qcom-apq8074-dragonboard 0 min 17.4 sec: PASS tegra30-beaver 0 min 19.5 sec: PASS am335x-boneblack 0 min 23.9 sec: PASS omap3-beagle-xm 0 min 48.1 sec: PASS sun7i-a20-cubieboard2 0 min 12.5 sec: PASS armada-370-mirabox 0 min 22.3 sec: PASS omap4-panda 0 min 54.6 sec: PASS armada-xp-openblocks-ax3-4 0 min 26.2 sec: PASS sun4i-a10-cubieboard 0 min 14.3 sec: PASS bcm28155-ap 0 min 27.2 sec: PASS omap3-overo-tobi 0 min 25.4 sec: PASS (Warnings: 1) imx6dl-wandboard,wand-solo 0 min 18.3 sec: PASS am335x-bone 0 min 27.1 sec: PASS omap3-overo-storm-tobi 0 min 21.4 sec: PASS omap5-uevm 1 min 47.9 sec: PASS (Warnings: 1) imx6q-wandboard 0 min 17.4 sec: PASS omap4-panda-es 0 min 57.6 sec: PASS imx6dl-wandboard,wand-dual 0 min 18.6 sec: PASS sama5_defconfig --------------- sama5d35ek 0 min 17.1 sec: PASS davinci_all_defconfig --------------------- legacy,dm365evm 0 min 17.5 sec: PASS da850-evm 0 min 15.4 sec: PASS

10 years, 8 months

mainline build: 8 warnings 0 failures (mainline/v3.14-8380-g3c83e61)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was mainline, found at: http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git (master branch) Topmost commit: 3c83e61 Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/mainline/v3.14-8380-g3c83e61/ Runtime: 30m 52s Passed: 123 Failed: 0 Warnings: 8 Section mismatches: 0 ------------------------------------------------------------------------------- Failed defconfigs: ------------------------------------------------------------------------------- Errors: Warnings: 1 drivers/mfd/sec-core.c:342:45: warning: 'regmap_rtc' may be used uninitialized in this function [-Wmaybe-uninitialized] 1 drivers/usb/host/xhci-plat.c:206:12: warning: 'xhci_plat_suspend' defined but not used [-Wunused-function] 1 drivers/usb/host/xhci-plat.c:214:12: warning: 'xhci_plat_resume' defined but not used [-Wunused-function] 1 net/netfilter/xt_connlimit.c:380:45: warning: division by zero [-Wdiv-by-zero] 2 buildall.arm.multi_lpae_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) 2 buildall.arm.multi_v7_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) Section mismatches:

10 years, 8 months

arm-soc boot: 25 passed 8 failed (arm-soc/v3.14-9179-gc2ef127)

by Olof's autobooter

Failed boards: cubie multi_v7_defconfig : FAILED 1:05.20 cubie2 sunxi_defconfig : FAILED 1:21.86 cubie2 multi_v7_defconfig : FAILED 1:11.71 cubie2 multi_lpae_defconfig : FAILED 1:04.69 hummingboard multi_v7_defconfig : FAILED 1:04.49 panda multi_v7_defconfig : FAILED 1:34.66 snowball multi_v7_defconfig : FAILED 1:14.94 wandboard multi_v7_defconfig : FAILED 1:11.34 Successful boards: apc vt8500_v6_v7_defconfig : passed 1:18.14 arndale exynos_defconfig : passed 1:06.96 bbb omap2plus_defconfig : passed 1:36.25 bbb multi_v7_defconfig : passed 1:16.13 beaver tegra_defconfig : passed 0:54.47 beaver multi_v7_defconfig : passed 0:57.63 capri bcm_defconfig : passed 0:43.36 capri multi_v7_defconfig : passed 0:44.51 cubie sunxi_defconfig : passed 1:11.88 dalmore tegra_defconfig : passed 1:28.70 dalmore multi_v7_defconfig : passed 1:16.61 dalmore multi_lpae_defconfig : passed 1:18.67 hummingboard imx_v6_v7_defconfig : passed 1:19.35 omap5uevm omap2plus_defconfig : warnings 1:13.42 omap5uevm multi_v7_defconfig : warnings 1:42.28 omap5uevm multi_lpae_defconfig : warnings 1:34.81 panda omap2plus_defconfig : passed 1:17.97 sama5 sama5_defconfig : passed 1:48.00 seaboard tegra_defconfig : passed 1:00.58 seaboard multi_v7_defconfig : passed 1:06.93 snow exynos_defconfig : passed 1:33.26 snowball u8500_defconfig : passed 1:21.15 trimslice tegra_defconfig : passed 1:00.45 trimslice multi_v7_defconfig : passed 1:07.57 wandboard imx_v6_v7_defconfig : passed 1:07.46 Offline boards: Board legend is available at http://arm-soc.lixom.net/boards.html Last entries of failed logs below: ======================================================================== Board cubie-multi_v7_defconfig failure log: ------------------------------------------------- tftp 0x40008000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.148 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage'. Load address: 0x40008000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 2.8 MiB/s done Bytes transferred = 4602520 (463a98 hex) sun4i#setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 sun4i#tftp 0x41000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/sun4i-a10-cubieboard.dtb tftp 0x41000000 arm-soc/v3.14-9179-gc2ef12node: cubie status: on 7/multi_v7_defconfig/dtbs/sun4i-a10-cubieboard.dtb Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.148 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/sun4i-a10-cubieboard.dtb'. Load address: 0x41000000 Loading: *## 494.1 KiB/s done Bytes transferred = 15184 (3b50 hex) sun4i#printenv bootargs printenv bootargs bootargs=console=ttyS0,115200n8 root=/dev/nfs rootwait rw nfsroot=172.16.1.7:/work/nfsroot/cubie ip=dhcp sun4i#bootz 0x40008000 - 0x41000000 bootz 0x40008000 - 0x41000000 Kernel image @ 0x40008000 [ 0x000000 - 0x463a98 ] ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 40ff9000, end 40fffb4f ... OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board cubie2-multi_lpae_defconfig failure log: ------------------------------------------------- sun7i# tftp 0x40008000 arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/zImage tftp 0x40008000 arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/zImage Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.164 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/zImage'. Load address: 0x40008000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4.1 MiB/s done Bytes transferred = 4626176 (469700 hex) sun7i# setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 sun7i# tftp 0x41000000 arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/dtbs/sun7i-a20-cubieboard2.dtb tftp 0x41000000 arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/dtbs/sun7i-a20-cubieboard2.dtb Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.164 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_lpae_defconfig/dtbs/sun7i-a20-cubieboard2.dtb'. Load address: 0x41000000 Loading: *## 597.7 KiB/s done Bytes transferred = 18361 (47b9 hex) sun7i# printenv bootargs printenv bootargs bootargs=console=ttyS0,115200n8 root=/dev/nfs rootwait rw nfsroot=172.16.1.7:/work/nfsroot/cubie2 ip=dhcp sun7i# bootz 0x40008000 - 0x41000000 bootz 0x40008000 - 0x41000000 Kernel image @ 0x40008000 [ 0x000000 - 0x469700 ] ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 40ff8000, end 40fff7b8 ... OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board cubie2-multi_v7_defconfig failure log: ------------------------------------------------- tftp 0x40008000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.164 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage'. Load address: 0x40008000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 4 MiB/s done Bytes transferred = 4602520 (463a98 hex) sun7i# setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 sun7i# tftp 0x41000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/sun7i-a20-cubieboard2.dtb tftp 0x41000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/sun7i-a20-cubieboard2.dtb Using emac device TFTP from server 172.16.1.3; our IP address is 172.16.1.164 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/sun7i-a20-cubieboard2.dtb'. Load address: 0x41000000 Loading: *## 3.5 MiB/s done Bytes transferred = 18361 (47b9 hex) sun7i# printenv bootargs printenode: cubie2 status: on nv bootargs bootargs=console=ttyS0,115200n8 root=/dev/nfs rootwait rw nfsroot=172.16.1.7:/work/nfsroot/cubie2 ip=dhcp sun7i# bootz 0x40008000 - 0x41000000 bootz 0x40008000 - 0x41000000 Kernel image @ 0x40008000 [ 0x000000 - 0x463a98 ] ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 40ff8000, end 40fff7b8 ... OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board cubie2-sunxi_defconfig failure log: ------------------------------------------------- [ 0.017806] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017829] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017842] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017862] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017875] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018830] Switched to clocksource arch_sys_counter [ 0.025906] NET: Registered protocol family 2 [ 0.026369] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026458] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026578] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026667] TCP: reno registered [ 0.026681] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026737] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026938] NET: Registered protocol family 1 [ 0.027331] RPC: Registered named UNIX socket transport module. [ 0.027343] RPC: Registered udp transport module. [ 0.027349] RPC: Registered tcp transport module. [ 0.027356] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028322] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028789] bounce pool size: 64 pages [ 0.036739] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036757] io scheduler noop registered [ 0.036764] io scheduler deadline registered [ 0.036953] io scheduler cfq registered (default) [ 0.038593] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080057] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.082483] console [ttyS0] disabled [ 0.102682] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.617751] console [ttyS0] enabled [ 0.622460] mousedev: PS/2 mouse device common for all mice [ 0.628283] i2c /dev entries driver [ 0.633123] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.642122] TCP: cubic registered [ 0.645443] NET: Registered protocol family 17 [ 0.650007] Registering SWP/SWPB emulation handler [ 0.655707] ahci-5v: 5000 mV [ 0.658984] usb1-vbus: 5000 mV [ 0.662346] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout ======================================================================== Board hummingboard-multi_v7_defconfig failure log: ------------------------------------------------- C1 U-Boot > tftp 0x10800000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage tftp 0x10800000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage Using FEC device TFTP from server 172.16.1.3; our IP address is 172.16.1.167 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage'. Load address: 0x10800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 1.9 MiB/s done Bytes transferred = 4602520 (463a98 hex) C1 U-Boot > setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 C1 U-Boot > tftp 0x11000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6dl-hummingboard.dtb tftp 0x11000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6dl-hummingboard.dtb Using FEC device TFTP from server 172.16.1.3; our IP address is 172.16.1.167 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6dl-hummingboard.dtb'. Load address: 0x11000000 Loading: *## 1.8 MiB/s done Bytes transferred = 25705 (6469 hex) C1 U-Boot > printenv bootargs printenv bootargs bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait debug earlyprintk C1 U-Boot >bootz 0x10800000 - 0x11000000 bootz 0x10800000 - 0x11000000 Kernel image @ 0x10800000 [ 0x000000 - 0x463a98 ] ## Flattened Device Tree blob at 11000000 Booting using the fdt blob at 0x11000000 Using Device Tree in place at 11000000, end 11009468 Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board panda-multi_v7_defconfig failure log: ------------------------------------------------- [ 1.612091] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.619720] omap_hsmmc 480d5000.mmc: vmmc regulator missing [ 1.625579] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.633392] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.640167] usbcore: registered new interface driver usbhid [ 1.645996] usbhid: USB HID core driver [ 1.653778] TCP: cubic registered [ 1.657226] NET: Registered protocol family 17 [ 1.662078] Key type dns_resolver registered [ 1.666992] Power Management for TI OMAP4+ devices. [ 1.672119] Power Management for TI OMAP4. [ 1.676391] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.683471] Registering SWP/SWPB emulation handler [ 1.689453] vwl1271: 1800 mV [ 1.693969] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.703887] twl 0-0048: PIH (irq 39) nested IRQs [ 1.709533] twl_rtc rtc.11: Power up reset detected. [ 1.715423] twl_rtc rtc.11: Enabling TWL-RTC [ 1.722351] twl_rtc rtc.11: rtc core: registered rtc.11 as rtc0 [ 1.729309] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.735412] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.741485] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.747589] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.753112] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.758544] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.763610] VDAC: 1800 mV [ 1.763610] VANA: 2100 mV [ 1.770874] VCXIO: 1800 mV [ 1.770874] VUSB: 3300 mV [ 1.777801] V1V8: 1800 mV [ 1.781402] V2V1: 2100 mV [ 1.787353] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.888244] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.060089] hub 1-1:1.0: USB hub found [ 2.064666] hub 1-1:1.0: 5 ports detected [ 2.568847] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.707336] smsc95xx v1.0.4 [ 4.288787] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, 0a:cf:6c:0b:f2:76 ~$off # PYBOOT: Exception: timeout ======================================================================== Board snowball-multi_v7_defconfig failure log: ------------------------------------------------- BOOTP broadcast 2 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.133 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x00100000 tmp/snowball-ycEKfY/tmp3ftog6-uImage tftp 0x00100000 tmp/snowball-ycEKfY/tmp3ftog6-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.133 Filename 'tmp/snowball-ycEKfY/tmp3ftog6-uImage'. Load address: 0x100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ######################################################### done Bytes transferred = 4643833 (46dbf9 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x00100000 bootm 0x00100000 ## Booting kernel from Legacy Image at 00100000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4643769 Bytes = 4.4 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board wandboard-multi_v7_defconfig failure log: ------------------------------------------------- tftp 0x10800000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage Using FEC device TFTP from server 172.16.1.3; our IP address is 172.16.1.165 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/zImage'. Load address: 0x10800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 6.2 MiB/s done Bytes transferred = 4602520 (463a98 hex) => setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 => tftp 0x11000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6q-wandboard.dtb tftp 0x11000000 arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6q-wandboard.dtb Using FEC device TFTP from server 172.16.1.3; our IP address is 172.16.1.165 Filename 'arm-soc/v3.14-9179-gc2ef127/multi_v7_defconfig/dtbs/imx6q-wandboard.dtb'. Load address: 0x11000000 Loading: *## 693.4 KiB/s done Bytes transferred = 29143 (71d7 hex) => printenv bootargs printenv bootargs bootargs=console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait debug => bootz 0x10800000 - 0x11000000 bootz 0x10800000 - 0x11000000 Kernel image @ 0x10800000 [ 0x000000 - 0x463a98 ] ## Flattened Device Tree blob at 11000000 Booting using the fdt blob at 0x11000000 Using Device Tree in place at 11000000, end 1100a1d6 node: wandboard status: on Starting kernel ... ~$off # PYBOOT: Exception: timeout

10 years, 8 months

arm-soc build: 9 warnings 0 failures (arm-soc/v3.14-9179-gc2ef127)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was arm-soc, found at: http://git.kernel.org/cgit/linux/kernel/git/arm/arm-soc.git (for-next or to-build branch) Topmost commit: c2ef127 arm-soc: add contents file Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/arm-soc/v3.14-9179-gc2ef127/ Runtime: 43m 39s Passed: 124 Failed: 0 Warnings: 9 Section mismatches: 2 ------------------------------------------------------------------------------- Failed defconfigs: ------------------------------------------------------------------------------- Errors: Warnings: 1 drivers/irqchip/irq-clps711x.c:78:1: warning: 'externally_visible' attribute have effect only on public objects [-Wattributes] 1 drivers/mfd/sec-core.c:342:45: warning: 'regmap_rtc' may be used uninitialized in this function [-Wmaybe-uninitialized] 1 drivers/usb/host/xhci-plat.c:206:12: warning: 'xhci_plat_suspend' defined but not used [-Wunused-function] 1 drivers/usb/host/xhci-plat.c:214:12: warning: 'xhci_plat_resume' defined but not used [-Wunused-function] 1 net/netfilter/xt_connlimit.c:380:45: warning: division by zero [-Wdiv-by-zero] 2 buildall.arm.multi_lpae_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) 2 buildall.arm.multi_v7_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) Section mismatches: 1 integrator_defconfig WARNING: arch/arm/mach-integrator/built-in.o(.data+0x2e0): Section mismatch in reference from the variable impd1_driver to the function .init.text:impd1_probe() 1 integrator_defconfig WARNING: vmlinux.o(.data+0x1b80): Section mismatch in reference from the variable impd1_driver to the function .init.text:impd1_probe()

10 years, 8 months

queue boot: 16 pass, 7 fail (v3.10.36)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: queue Git describe: v3.10.36 Failed boot tests (console logs at the end) =========================================== omap3-beagle-xm: DEAD: omap2plus_defconfig imx6dl-wandboard,wand-dual: FAIL: imx_v6_v7_defconfig imx6dl-wandboard,wand-solo: OFFLINE: imx_v6_v7_defconfig armada-xp-openblocks-ax3-4: FAIL: multi_v7_defconfig armada-370-mirabox: DEAD: multi_v7_defconfig sun4i-a10-cubieboard: FAIL: multi_v7_defconfig da850-evm: FAIL: davinci_all_defconfig Full Report =========== da8xx_omapl_defconfig --------------------- da850-evm 0 min 14.5 sec: PASS legacy,da850evm 0 min 13.9 sec: PASS omap2plus_defconfig ------------------- legacy,3730xm 0 min 55.0 sec: PASS omap3-beagle-xm 0 min 0.0 sec: DEAD legacy,3530beagle 0 min 57.6 sec: PASS omap4-panda 1 min 9.3 sec: PASS omap3-tobi 0 min 33.6 sec: PASS am335x-bone 0 min 26.6 sec: PASS omap4-panda-es 1 min 3.7 sec: PASS legacy,3730storm 0 min 23.4 sec: PASS legacy,3530overo 0 min 21.2 sec: PASS tegra_defconfig --------------- tegra30-beaver 0 min 17.2 sec: PASS imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual 0 min 42.3 sec: FAIL imx6dl-wandboard,wand-solo 0 min 31.4 sec: OFFLINE mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 0 min 21.4 sec: PASS armada-370-mirabox 0 min 19.6 sec: PASS exynos_defconfig ---------------- exynos5250-arndale 0 min 28.9 sec: PASS multi_v7_defconfig ------------------ armada-xp-openblocks-ax3-4 0 min 21.2 sec: FAIL armada-370-mirabox 0 min 0.0 sec: DEAD sun4i-a10-cubieboard 1 min 45.0 sec: FAIL sama5_defconfig --------------- sama5d35ek 0 min 17.0 sec: PASS davinci_all_defconfig --------------------- legacy,dm365evm 0 min 16.4 sec: PASS da850-evm 0 min 40.8 sec: FAIL Console logs for failures ========================= omap2plus_defconfig ------------------- omap3-beagle-xm: DEAD: last 80 lines of boot log: ------------------------------------------------- DRAM: 512 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0 *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Beagle xM Rev C No EEPROM on expansion board Die ID #0b5000029ff80000016842c910019004 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 1.800 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 480ab000 using PIO, IRQ 0 Net: usb_ether Hit any key to stop autoboot: 3 0 OMAP3 beagleboard.org # OMAP3 beagleboard.org # version version U-Boot 2013.04 (Jan 17 2014 - 10:48:29) arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.3-1ubuntu1) 4.7.3 GNU ld (GNU Binutils for Ubuntu) 2.23.2 OMAP3 beagleboard.org #setenv usbethaddr 2a:45:34:6d:b4:5d setenv usbethaddr 2a:45:34:6d:b4:5d OMAP3 beagleboard.org # setenv preboot "dcache off; usb start" # For USB net setenv preboot "dcache off; usb start" # For USB net OMAP3 beagleboard.org # setenv bootargs console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 setenv bootargs console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 OMAP3 beagleboard.org # setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254' setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254' OMAP3 beagleboard.org #if test -n ${initenv}; then run initenv; fi if test -n ${initenv}; then run initenv; fi OMAP3 beagleboard.org # if test -n ${preboot}; then run preboot; fi if test -n ${preboot}; then run preboot; fi (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 1 Ethernet Device(s) found OMAP3 beagleboard.org # setenv autoload no; setenv autoboot no setenv autoload no; setenv autoboot no OMAP3 beagleboard.org #dhcp dhcp ERROR: Need valid 'usbnet_devaddr' to be set at ether.c:2369/usb_eth_init() Waiting for Ethernet connection... done. BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.1.190 OMAP3 beagleboard.org # setenv serverip 192.168.1.2 setenv serverip 192.168.1.2 OMAP3 beagleboard.org #if test -n ${netargs}; then run netargs; fi if test -n ${netargs}; then run netargs; fi OMAP3 beagleboard.org # tftp 0x80200000 192.168.1.2:tmp/3730xm-M1ksw2/zImage tftp 0x80200000 192.168.1.2:tmp/3730xm-M1ksw2/zImage Waiting for Ethernet connection... done. Using sms0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.190 Filename 'tmp/3730xm-M1ksw2/zImage'. Load address: 0x80200000 Loading: *T ################################################################# ################################################################# ################################################################# ################################################################# ############## 461.9 KiB/s done Bytes transferred = 4022136 (3d5f78 hex) OMAP3 beagleboard.org #tftp 0x81000000 192.168.1.2:buildroot.cpio.gz.uboot tftp 0x81000000 192.168.1.2:buildroot.cpio.gz.uboot Waiting for Ethernet connection... done. Using sms0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.190 Filename 'buildroot.cpio.gz.uboot'. Load address: 0x81000000 Loading: * imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual: FAIL: last 80 lines of boot log: ------------------------------------------------------------ => version version U-Boot 2013.04-00012-g0b44183 (May 15 2013 - 16:00:22) arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2010.09-50) 4.5.1 GNU ld (Sourcery G++ Lite 2010.09-50) 2.20.51.20100809 => setenv bootargs console=ttymxc0,115200 rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 setenv bootargs console=ttymxc0,115200 rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 => setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254' setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254' =>if test -n ${initenv}; then run initenv; fi if test -n ${initenv}; then run initenv; fi => if test -n ${preboot}; then run preboot; fi if test -n ${preboot}; then run preboot; fi =>setenv autoload no; setenv autoboot no setenv autoload no; setenv autoboot no =>dhcp dhcp FEC Waiting for PHY auto negotiation to complete.. done BOOTP broadcast 1 DHCP client bound to address 192.168.1.156 => setenv serverip 192.168.1.2 setenv serverip 192.168.1.2 =>if test -n ${netargs}; then run netargs; fi if test -n ${netargs}; then run netargs; fi => tftp 0x18000000 192.168.1.2:tmp/wand-dual-ePRDWn/zImage tftp 0x18000000 192.168.1.2:tmp/wand-dual-ePRDWn/zImage Using FEC device TFTP from server 192.168.1.2; our IP address is 192.168.1.156 Filename 'tmp/wand-dual-ePRDWn/zImage'. Load address: 0x18000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ########################### 1.5 MiB/s done Bytes transferred = 4207992 (403578 hex) => tftp 0x20000000 192.168.1.2:buildroot.cpio.gz.uboot tftp 0x20000000 192.168.1.2:buildroot.cpio.gz.uboot Using FEC device TFTP from server 192.168.1.2; our IP address is 192.168.1.156 Filename 'buildroot.cpio.gz.uboot'. Load address: 0x20000000 Loading: *############################################ 1.5 MiB/s done Bytes transferred = 642602 (9ce2a hex) => tftp 0x1f000000 192.168.1.2:tmp/wand-dual-ePRDWn/imx6dl-wandboard.dtb tftp 0x1f000000 192.168.1.2:tmp/wand-dual-ePRDWn/imx6dl-wandboard.dtb Using FEC device TFTP from server 192.168.1.2; our IP address is 192.168.1.156 Filename 'tmp/wand-dual-ePRDWn/imx6dl-wandboard.dtb'. Load address: 0x1f000000 Loading: *## 1.4 MiB/s done Bytes transferred = 18975 (4a1f hex) => printenv bootargs printenv bootargs bootargs=console=ttymxc0,115200 rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.156:192.168.1.2:192.168.1.254:255.255.255.0:::none:192.168.1.254 =>bootz 0x18000000 0x20000000 0x1f000000 bootz 0x18000000 0x20000000 0x1f000000 ## Loading init Ramdisk from Legacy Image at 20000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 642538 Bytes = 627.5 KiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 1f000000 Booting using the fdt blob at 0x1f000000 Using Device Tree in place at 1f000000, end 1f007a1e Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 42.28 seconds. # PYBOOT: Result: FAIL imx6dl-wandboard,wand-solo: OFFLINE: last 80 lines of boot log: --------------------------------------------------------------- Connected to wand-solo console [channel connected] (~$quit to exit) (user:khilman) is already connected ~$hardreset Command(wand-solo console)> hardreset (user:khilman) Reboot wand-solo Reboot: wand-solo ; phidget 2 2 : off, sleep, on U-Boot 2013.04-00012-g0b44183-dirty (May 15 2013 - 16:16:11) CPU: Freescale i.MX6SOLO rev1.1 at 792 MHz Reset cause: POR Board: Wandboard DRAM: 512 MiB WARNING: Caches not enabled MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default env 0 => ~$off # PYBOOT: Exception: ('ERROR: Could not break into u-boot.', 'OFFLINE') # PYBOOT: Time: 31.37 seconds. # PYBOOT: Result: OFFLINE multi_v7_defconfig ------------------ armada-xp-openblocks-ax3-4: FAIL: last 80 lines of boot log: ------------------------------------------------------------ pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti(a)linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 Switching to clocksource armada_370_xp_clocksource bounce pool size: 64 pages Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-xp-pinctrl d0018000.pinctrl: registered pinctrl driver ipmi message handler version 39.2 IPMI System Interface driver. ipmi_si: Adding default-specified kcs state machine ipmi_si: Trying default-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <0000000000000ca2-0000000000000ca2> Trying to free nonexistent resource <0000000000000ca3-0000000000000ca3> ipmi_si: Adding default-specified smic state machine ipmi_si: Trying default-specified smic state machine at i/o address 0xca9, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <0000000000000ca9-0000000000000ca9> Trying to free nonexistent resource <0000000000000caa-0000000000000caa> Trying to free nonexistent resource <0000000000000cab-0000000000000cab> ipmi_si: Adding default-specified bt state machine ipmi_si: Trying default-specified bt state machine at i/o address 0xe4, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <00000000000000e4-00000000000000e4> Trying to free nonexistent resource <00000000000000e5-00000000000000e5> Trying to free nonexistent resource <00000000000000e6-00000000000000e6> ipmi_si: Unable to find any System Interface(s) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 17) is a 16550A console [ttyS0] enabled d0012100.serial: ttyS1 at MMIO 0xd0012100 (irq = 18) is a 16550A sata_mv d00a0000.sata: slots 32 ports 2 scsi0 : sata_mv scsi1 : sata_mv ata1: SATA max UDMA/133 irq 24 ata2: SATA max UDMA/133 irq 24 usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper usbcore: registered new interface driver usbhid usbhid: USB HID core driver VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 Registering SWP/SWPB emulation handler /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) ata1: SATA link down (SStatus 0 SControl F300) ata2: SATA link down (SStatus 0 SControl F300) List of all partitions: No filesystem could mount root, tried: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.10.36 #1 [<c0013c0c>] (unwind_backtrace+0x0/0xf4) from [<c00114b0>] (show_stack+0x10/0x14) [<c00114b0>] (show_stack+0x10/0x14) from [<c0276480>] (panic+0xa0/0x1e8) [<c0276480>] (panic+0xa0/0x1e8) from [<c0329110>] (mount_block_root+0x294/0x298) [<c0329110>] (mount_block_root+0x294/0x298) from [<c03292c4>] (prepare_namespace+0x14c/0x184) [<c03292c4>] (prepare_namespace+0x14c/0x184) from [<c0328d60>] (kernel_init_freeable+0x1c8/0x1d8) [<c0328d60>] (kernel_init_freeable+0x1c8/0x1d8) from [<c02721dc>] (kernel_init+0x8/0x158) [<c02721dc>] (kernel_init+0x8/0x158) from [<c000df18>] (ret_from_fork+0x14/0x3c) CPU0: stopping CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.36 #1 [<c0013c0c>] (unwind_backtrace+0x0/0xf4) from [<c00114b0>] (show_stack+0x10/0x14) [<c00114b0>] (show_stack+0x10/0x14) from [<c001238c>] (handle_IPI+0x108/0x130) [<c001238c>] (handle_IPI+0x108/0x130) from [<c000851c>] (armada_370_xp_handle_irq+0x90/0xa8) [<c000851c>] (armada_370_xp_handle_irq+0x90/0xa8) from [<c000dac0>] (__irq_svc+0x40/0x50) Exception stack(0xc0359f70 to 0xc0359fb8) 9f60: c1d5c6d8 00000000 000000ba 000000ba 9f80: c03604a8 c0358000 c036045c c0383c6c c027deb0 c0358000 c0383c6c c0358000 9fa0: 0000001f c0359fb8 c000f070 c004fa8c 60000113 ffffffff [<c000dac0>] (__irq_svc+0x40/0x50) from [<c004fa8c>] (cpu_startup_entry+0xfc/0x140) [<c004fa8c>] (cpu_startup_entry+0xfc/0x140) from [<c0328a3c>] (start_kernel+0x2c4/0x2d0) [<c0328a3c>] (start_kernel+0x2c4/0x2d0) from [<00008074>] (0x8074) ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: Kernel panic # PYBOOT: Time: 21.22 seconds. # PYBOOT: Result: FAIL armada-370-mirabox: DEAD: last 80 lines of boot log: ---------------------------------------------------- Connected to mirabox console [channel connected] (~$quit to exit) (user:khilman) is already connected ~$hardreset Command(mirabox console)> hardreset (user:khilman) Reboot mirabox Reboot: mirabox ; ip9258 1 1 : off, sleep, on sun4i-a10-cubieboard: FAIL: last 80 lines of boot log: ------------------------------------------------------ pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) .text : 0xc0008000 - 0xc0327ac0 (3199 kB) .init : 0xc0328000 - 0xc0356780 ( 186 kB) .data : 0xc0358000 - 0xc0383d20 ( 176 kB) .bss : 0xc0383d20 - 0xc03b68ac ( 203 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. NR_IRQS:16 nr_irqs:16 16 sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms Console: colour dummy device 80x30 Calibrating delay loop... 669.28 BogoMIPS (lpj=3346432) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket -1, mpidr 0 Setting up static identity map for 0xc027be58 - 0xc027beb0 unable to find compatible sirf rstc node in dtb Brought up 1 CPUs SMP: Total of 1 processors activated (669.28 BogoMIPS). CPU: All CPU(s) started in SVC mode. pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations unable to find compatible sirf pwrc node in dtb Serial: AMBA PL011 UART driver bio: create slab <bio-0> at 0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti(a)linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 bounce pool size: 64 pages Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver ipmi message handler version 39.2 IPMI System Interface driver. ipmi_si: Adding default-specified kcs state machine ipmi_si: Trying default-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <0000000000000ca2-0000000000000ca2> Trying to free nonexistent resource <0000000000000ca3-0000000000000ca3> ipmi_si: Adding default-specified smic state machine ipmi_si: Trying default-specified smic state machine at i/o address 0xca9, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <0000000000000ca9-0000000000000ca9> Trying to free nonexistent resource <0000000000000caa-0000000000000caa> Trying to free nonexistent resource <0000000000000cab-0000000000000cab> ipmi_si: Adding default-specified bt state machine ipmi_si: Trying default-specified bt state machine at i/o address 0xe4, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <00000000000000e4-00000000000000e4> Trying to free nonexistent resource <00000000000000e5-00000000000000e5> Trying to free nonexistent resource <00000000000000e6-00000000000000e6> ipmi_si: Unable to find any System Interface(s) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 17) is a U6_16550A console [ttyS0] enabled usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper usbcore: registered new interface driver usbhid usbhid: USB HID core driver VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 Registering SWP/SWPB emulation handler /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 104.96 seconds. # PYBOOT: Result: FAIL davinci_all_defconfig --------------------- da850-evm: FAIL: last 80 lines of boot log: ------------------------------------------- Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. MMC: davinci: 0 SF: Detected M25P64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial SF: Detected M25P64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB Net: DaVinci-EMAC Hit any key to stop autoboot: 3 0 U-Boot > U-Boot > version version U-Boot 2014.01-dirty (Feb 27 2014 - 15:12:48) arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.3-1ubuntu1) 4.7.3 GNU ld (GNU Binutils for Ubuntu) 2.23.52.20130913 U-Boot >setenv bootargs console=ttyS2,115200n8 debug earlyprintk setenv bootargs console=ttyS2,115200n8 debug earlyprintk U-Boot >if test -n ${initenv}; then run initenv; fi if test -n ${initenv}; then run initenv; fi U-Boot > if test -n ${preboot}; then run preboot; fi if test -n ${preboot}; then run preboot; fi U-Boot > setenv autoload no; setenv autoboot no setenv autoload no; setenv autoboot no U-Boot > dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.1.194 U-Boot > setenv serverip 192.168.1.2 setenv serverip 192.168.1.2 U-Boot > if test -n ${netargs}; then run netargs; fi if test -n ${netargs}; then run netargs; fi U-Boot > tftp 0xc0800000 192.168.1.2:tmp/da850evm-xqp607/zImage-dtb-gNhknO tftp 0xc0800000 192.168.1.2:tmp/da850evm-xqp607/zImage-dtb-gNhknO Using DaVinci-EMAC device TFTP from server 192.168.1.2; our IP address is 192.168.1.194 Filename 'tmp/da850evm-xqp607/zImage-dtb-gNhknO'. Load address: 0xc0800000 Loading: *################################################################# ################################################################# ######## 1.7 MiB/s done Bytes transferred = 2023756 (1ee14c hex) U-Boot > tftp 0xc0c00000 192.168.1.2:buildroot.cpio.gz.uboot tftp 0xc0c00000 192.168.1.2:buildroot.cpio.gz.uboot Using DaVinci-EMAC device TFTP from server 192.168.1.2; our IP address is 192.168.1.194 Filename 'buildroot.cpio.gz.uboot'. Load address: 0xc0c00000 Loading: *############################################ 1.7 MiB/s done Bytes transferred = 642602 (9ce2a hex) U-Boot >printenv bootargs printenv bootargs bootargs=console=ttyS2,115200n8 debug earlyprintk U-Boot > bootz 0xc0800000 0xc0c00000 bootz 0xc0800000 0xc0c00000 Kernel image @ 0xc0800000 [ 0x000000 - 0x1ec9f8 ] ## Loading init Ramdisk from Legacy Image at c0c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 642538 Bytes = 627.5 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 40.83 seconds. # PYBOOT: Result: FAIL

10 years, 8 months

queue boot: 9 passed 1 failed (queue/v3.10.36)

by Olof's autobooter

Failed boards: cubie multi_v7_defconfig : FAILED 0:23.30 Successful boards: arndale exynos_defconfig : passed 1:02.72 beaver tegra_defconfig : passed 0:44.44 cubox dove_defconfig : passed 0:57.09 dalmore tegra_defconfig : passed 1:08.25 panda omap2plus_defconfig : passed 1:12.45 sama5 sama5_defconfig : passed 1:53.19 seaboard tegra_defconfig : passed 0:53.56 snow exynos_defconfig : passed 1:26.55 trimslice tegra_defconfig : passed 1:14.70 Offline boards: Board legend is available at http://arm-soc.lixom.net/boards.html Last entries of failed logs below: ======================================================================== Board cubie-multi_v7_defconfig failure log: ------------------------------------------------- Trying to free nonexistent resource <0000000000000ca3-0000000000000ca3> ipmi_si: Adding default-specified smic state machine ipmi_si: Trying default-specified smic state machine at i/o address 0xca9, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <0000000000000ca9-0000000000000ca9> Trying to free nonexistent resource <0000000000000caa-0000000000000caa> Trying to free nonexistent resource <0000000000000cab-0000000000000cab> ipmi_si: Adding default-specified bt state machine ipmi_si: Trying default-specified bt state machine at i/o address 0xe4, slave address 0x0, irq 0 ipmi_si: Could not set up I/O space Trying to free nonexistent resource <00000000000000e4-00000000000000e4> Trying to free nonexistent resource <00000000000000e5-00000000000000e5> Trying to free nonexistent resource <00000000000000e6-00000000000000e6> ipmi_si: Unable to find any System Interface(s) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 17) is a U6_16550A console [ttyS0] enabled usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper usbcore: registered new interface driver usbhid usbhid: USB HID core driver VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 Registering SWP/SWPB emulation handler /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) List of all partitions: No filesystem could mount root, tried: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,255) CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.36 #1 [<c0013c0c>] (unwind_backtrace+0x0/0xf4) from [<c00114b0>] (show_stack+0x10/0x14) [<c00114b0>] (show_stack+0x10/0x14) from [<c0276480>] (panic+0xa0/0x1e8) [<c0276480>] (panic+0xa0/0x1e8) from [<c0329110>] (mount_block_root+0x294/0x298) [<c0329110>] (mount_block_root+0x294/0x298) from [<c03292c4>] (prepare_namespace+0x14c/0x184) [<c03292c4>] (prepare_namespace+0x14c/0x184) from [<c0328d60>] (kernel_init_freeable+0x1c8/0x1d8) [<c0328d60>] (kernel_init_freeable+0x1c8/0x1d8) from [<c02721dc>] (kernel_init+0x8/0x158) [<c02721dc>] (kernel_init+0x8/0x158) from [<c000df18>] (ret_from_fork+0x14/0x3c) ~$off # PYBOOT: Exception: panic

10 years, 8 months

← Newer
1
...
21
22
23
24
25
26
27
...
32
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

Kernel-build-reports April 2014