Connected to octa console [channel connected] (~$quit to exit)
(user:khilman) is already connected
(user:khilman) is already connected

~$hardreset

Command(octa console)> hardreset
(user:khilman) Reboot octa


U-Boot 2012.07-00001-g02b1decad082 (Feb 24 2014 - 14:16:18) for ARNDALE OCTA

CPU: Exynos5420 Rev2.0 [Samsung SOC on SMP Platform Base on ARM CortexA15]
APLL = 800MHz, KPLL = 600MHz
MPLL = 532MHz, BPLL = 800MHz

Board: ARNDALE OCTA
DRAM:  2 GiB
WARNING: Caches not enabled

TrustZone Enabled BSP
BL1 version: 

Checking Boot Mode ... SDMMC
MMC:   S5P_MSHC2: 0, S5P_MSHC0: 1
MMC Device 0: 7.4 GiB
MMC Device 1: 3.6 GiB
MMC Device 2: MMC Device 2 not found
there are pending interrupts 0x00000001
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... The request port(2) is not configured
The request port(2) is not configured
3 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
       scanning usb for ethernet devices... 1 Ethernet Device(s) found
Hit any key to stop autoboot: 
 1  0 
ARNDALE # 
ARNDALE # version
version

U-Boot 2012.07-00001-g02b1decad082 (Feb 24 2014 - 14:16:18) for ARNDALE OCTA
arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.3-1ubuntu1) 4.7.3
GNU ld (GNU Binutils for Ubuntu) 2.23.52.20130913
ARNDALE # setenv ethaddr 6e:e6:84:36:8e:9fs
setenv ethaddr 6e:e6:84:36:8e:9fs
ARNDALE # setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
ARNDALE # setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
ARNDALE # setenv bootargs console=ttySAC3,115200n8 debug earlyprintk
setenv bootargs console=ttySAC3,115200n8 debug earlyprintk
ARNDALE # setenv netargs 'setenv bootargs ${bootargs} 'ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254''
setenv netargs 'setenv bootargs ${bootargs} 'ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254''
ARNDALE # if test -n ${initenv}; then run initenv; fi
if test -n ${initenv}; then run initenv; fi
ARNDALE #if test -n ${preboot}; then run preboot; fi
 if test -n ${preboot}; then run preboot; fi
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... The request port(2) is not configured
The request port(2) is not configured
3 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
       scanning usb for ethernet devices... 1 Ethernet Device(s) found
ARNDALE # setenv autoload no; setenv autoboot no
setenv autoload no; setenv autoboot no
ARNDALE #dhcp
 dhcp
Waiting for Ethernet connection... done.
BOOTP broadcast 1
DHCP client bound to address 192.168.1.196
ARNDALE #setenv serverip 192.168.1.2
 setenv serverip 192.168.1.2
ARNDALE # if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
ARNDALE # tftp 0x21000000 192.168.1.2:tmp/octa-8KJ_Nh/zImage
tftp 0x21000000 192.168.1.2:tmp/octa-8KJ_Nh/zImage
Waiting for Ethernet connection... done.
Using asx0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.196
Filename 'tmp/octa-8KJ_Nh/zImage'.
Load address: 0x21000000
Loading: *#################################################################
	 #################################################################
	 ###############################################################
done
Bytes transferred = 2819416 (2b0558 hex)
ARNDALE # tftp 0x22000000 192.168.1.2:buildroot.cpio.gz
tftp 0x22000000 192.168.1.2:buildroot.cpio.gz
Waiting for Ethernet connection... done.
Using asx0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.196
Filename 'buildroot.cpio.gz'.
Load address: 0x22000000
Loading: *############################################
done
Bytes transferred = 642538 (9cdea hex)
ARNDALE # tftp 0x23000000 192.168.1.2:tmp/octa-8KJ_Nh/tmpXK6AeE.dtb
tftp 0x23000000 192.168.1.2:tmp/octa-8KJ_Nh/tmpXK6AeE.dtb
Waiting for Ethernet connection... done.
Using asx0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.196
Filename 'tmp/octa-8KJ_Nh/tmpXK6AeE.dtb'.
Load address: 0x23000000
Loading: *###
done
Bytes transferred = 32956 (80bc hex)
ARNDALE # printenv bootargs
printenv bootargs
bootargs=console=ttySAC3,115200n8 debug earlyprintk ip=::::::none:192.168.1.254
ARNDALE # bootz 0x21000000 - 0x23000000
bootz 0x21000000 - 0x23000000
## Flattened Device Tree blob at 23000000
   Booting using the fdt blob at 0x23000000
   Using Device Tree in place at 23000000, end 2300b0bb

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.15.0-08884-g2dc24b0 (buildslave@kbuilderdedi01) (gcc version 4.7.1 (Ubuntu/Linaro 4.7.1-5ubuntu1~ppa1) ) #1 SMP PREEMPT Wed Jun 11 21:22:45 CEST 2014
[    0.000000] CPU: ARMv7 Processor [412fc0f3] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: Insignal Arndale Octa evaluation board based on EXYNOS5420
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 584192
[    0.000000] free_area_init_node: node 0, pgdat c0552880, node_mem_map edbf4000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 192512 pages, LIFO batch:31
[    0.000000]   HighMem zone: 5648 pages used for memmap
[    0.000000]   HighMem zone: 391680 pages, LIFO batch:31
[    0.000000] Running under secure firmware.
[    0.000000] PERCPU: Embedded 7 pages/cpu @edb79000 s7104 r8192 d13376 u32768
[    0.000000] pcpu-alloc: s7104 r8192 d13376 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 582672
[    0.000000] Kernel command line: console=ttySAC3,115200n8 debug earlyprintk ip=::::::none:192.168.1.254
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 2310796K/2336768K available (3723K kernel code, 237K rwdata, 1200K rodata, 254K init, 267K bss, 25972K reserved, 1566720K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc04d7024   (4925 kB)
[    0.000000]       .init : 0xc04d8000 - 0xc0517bc0   ( 255 kB)
[    0.000000]       .data : 0xc0518000 - 0xc0553420   ( 238 kB)
[    0.000000]        .bss : 0xc055342c - 0xc05963c4   ( 268 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C: failed to init: -19
[    0.000008] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[    0.000363] Console: colour dummy device 80x30
[    0.000392] Calibrating delay loop... 1590.88 BogoMIPS (lpj=3977216)
[    0.045027] pid_max: default: 32768 minimum: 301
[    0.045215] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.045229] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.045891] CPU: Testing write buffer coherency: ok
[    0.046250] CPU0: update cpu_power 1535
[    0.046264] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.046433] Setting up static identity map for 0x203889b0 - 0x20388a08
[    2.075047] CPU1: failed to come online
[    4.085081] CPU2: failed to come online
[    6.095118] CPU3: failed to come online
[    8.105153] CPU4: failed to come online
[   10.115186] CPU5: failed to come online
[   12.125220] CPU6: failed to come online
[   14.135256] CPU7: failed to come online
[   14.135304] Brought up 1 CPUs
[   14.135318] SMP: Total of 1 processors activated.
[   14.135332] CPU: All CPU(s) started in SVC mode.
[   14.135954] devtmpfs: initialized
[   14.149892] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[   14.150560] pinctrl core: initialized pinctrl subsystem
[   14.151011] regulator-dummy: no parameters
[   14.181973] NET: Registered protocol family 16
[   14.182170] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   14.188357] gpiochip_add: registered GPIOs 0 to 7 on device: gpy7
[   14.188378] gpiochip_add: registered GPIOs 8 to 15 on device: gpx0
[   14.188398] gpiochip_add: registered GPIOs 16 to 23 on device: gpx1
[   14.188416] gpiochip_add: registered GPIOs 24 to 31 on device: gpx2
[   14.188434] gpiochip_add: registered GPIOs 32 to 39 on device: gpx3
[   14.190048] gpiochip_add: registered GPIOs 40 to 47 on device: gpc0
[   14.190068] gpiochip_add: registered GPIOs 48 to 55 on device: gpc1
[   14.190087] gpiochip_add: registered GPIOs 56 to 62 on device: gpc2
[   14.190104] gpiochip_add: registered GPIOs 63 to 66 on device: gpc3
[   14.190123] gpiochip_add: registered GPIOs 67 to 68 on device: gpc4
[   14.190142] gpiochip_add: registered GPIOs 69 to 76 on device: gpd1
[   14.190159] gpiochip_add: registered GPIOs 77 to 82 on device: gpy0
[   14.190177] gpiochip_add: registered GPIOs 83 to 86 on device: gpy1
[   14.190195] gpiochip_add: registered GPIOs 87 to 92 on device: gpy2
[   14.190213] gpiochip_add: registered GPIOs 93 to 100 on device: gpy3
[   14.190287] gpiochip_add: registered GPIOs 101 to 108 on device: gpy4
[   14.190306] gpiochip_add: registered GPIOs 109 to 116 on device: gpy5
[   14.190324] gpiochip_add: registered GPIOs 117 to 124 on device: gpy6
[   14.191535] gpiochip_add: registered GPIOs 125 to 132 on device: gpe0
[   14.191555] gpiochip_add: registered GPIOs 133 to 134 on device: gpe1
[   14.191574] gpiochip_add: registered GPIOs 135 to 140 on device: gpf0
[   14.191592] gpiochip_add: registered GPIOs 141 to 148 on device: gpf1
[   14.191611] gpiochip_add: registered GPIOs 149 to 156 on device: gpg0
[   14.191630] gpiochip_add: registered GPIOs 157 to 164 on device: gpg1
[   14.191648] gpiochip_add: registered GPIOs 165 to 166 on device: gpg2
[   14.191666] gpiochip_add: registered GPIOs 167 to 170 on device: gpj4
[   14.192560] gpiochip_add: registered GPIOs 171 to 178 on device: gpa0
[   14.192580] gpiochip_add: registered GPIOs 179 to 184 on device: gpa1
[   14.192598] gpiochip_add: registered GPIOs 185 to 192 on device: gpa2
[   14.192616] gpiochip_add: registered GPIOs 193 to 197 on device: gpb0
[   14.192635] gpiochip_add: registered GPIOs 198 to 202 on device: gpb1
[   14.192653] gpiochip_add: registered GPIOs 203 to 206 on device: gpb2
[   14.192671] gpiochip_add: registered GPIOs 207 to 214 on device: gpb3
[   14.192690] gpiochip_add: registered GPIOs 215 to 216 on device: gpb4
[   14.192709] gpiochip_add: registered GPIOs 217 to 224 on device: gph0
[   14.194090] gpiochip_add: registered GPIOs 225 to 231 on device: gpz
[   14.196372] exynos-audss-clk 3810000.audss-clock-controller: setup completed
[   14.209845] EXYNOS: PMU not supported
[   14.241299] SCSI subsystem initialized
[   14.241994] usbcore: registered new interface driver usbfs
[   14.242170] usbcore: registered new interface driver hub
[   14.242500] usbcore: registered new device driver usb
[   14.245465] Switched to clocksource mct-frc
[   14.264901] NET: Registered protocol family 2
[   14.265793] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[   14.265910] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[   14.266121] TCP: Hash tables configured (established 8192 bind 8192)
[   14.266186] TCP: reno registered
[   14.266209] UDP hash table entries: 512 (order: 2, 24576 bytes)
[   14.266263] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[   14.266620] NET: Registered protocol family 1
[   14.267003] Trying to unpack rootfs image as initramfs...
[   14.346134] Freeing initrd memory: 624K (c2000000 - c209c000)
[   14.348874] futex hash table entries: 2048 (order: 5, 131072 bytes)
[   14.380095] ROMFS MTD (C) 2007 Red Hat, Inc.
[   14.380741] msgmni has been set to 1454
[   14.382413] bounce: pool size: 64 pages
[   14.382438] io scheduler noop registered
[   14.382461] io scheduler deadline registered
[   14.383416] io scheduler cfq registered (default)
[   14.506613] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[   14.509888] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 83, base_baud = 0) is a S3C6400/10
[   14.510801] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 84, base_baud = 0) is a S3C6400/10
[   14.511570] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 85, base_baud = 0) is a S3C6400/10
[   14.512476] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 86, base_baud = 0) is a S3C6400/10
[   15.270615] console [ttySAC3] enabled
[   15.292972] brd: module loaded
[   15.303478] loop: module loaded
[   15.306683] usbcore: registered new interface driver asix
[   15.311163] usbcore: registered new interface driver ax88179_178a
[   15.317448] usbcore: registered new interface driver cdc_ether
[   15.323150] usbcore: registered new interface driver smsc75xx
[   15.329112] usbcore: registered new interface driver smsc95xx
[   15.334619] usbcore: registered new interface driver net1080
[   15.340259] usbcore: registered new interface driver cdc_subset
[   15.346289] usbcore: registered new interface driver zaurus
[   15.351762] usbcore: registered new interface driver cdc_ncm
[   15.358504] usb@12000000 supply vdd33 not found, using dummy regulator
[   15.364172] usb@12000000 supply vdd10 not found, using dummy regulator
[   15.371432] platform 12000000.dwc3: Driver dwc3 requests probe deferral
[   15.377854] usb@12400000 supply vdd33 not found, using dummy regulator
[   15.383663] usb@12400000 supply vdd10 not found, using dummy regulator
[   15.391157] platform 12400000.dwc3: Driver dwc3 requests probe deferral
[   15.396949] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   15.403527] ehci-exynos: EHCI EXYNOS driver
[   15.407681] of_get_named_gpiod_flags: can't parse gpios property of node '/usb@12110000[0]'
[   15.416175] exynos-ehci 12110000.usb: no usb2 phy configured
[   15.421493] platform 12110000.usb: Driver exynos-ehci requests probe deferral
[   15.429179] usbcore: registered new interface driver usb-storage
[   15.436227] mousedev: PS/2 mouse device common for all mice
[   15.442064] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[   15.447226] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc0
[   15.452840] s3c-rtc 101e0000.rtc: warning: invalid RTC value so initializing it
[   15.496429] Unhandled fault: external abort on non-linefetch (0x008) at 0xffc00000
[   15.502521] Internal error: : 8 [#1] PREEMPT SMP ARM
[   15.507455] Modules linked in:
[   15.510494] CPU: 0 PID: 1061 Comm: kworker/u16:0 Not tainted 3.15.0-08884-g2dc24b0 #1
[   15.518289] task: ef2ffc00 ti: ef3e0000 task.ti: ef3e0000
[   15.523667] PC is at __copy_to_user_std+0x4c/0x3a8
[   15.528431] LR is at copy_page_to_iter+0xac/0x274
[   15.533108] pc : [<c01b6acc>]    lr : [<c0096430>]    psr: 60000113
[   15.533108] sp : ef3e1dcc  ip : 00000000  fp : ef5f3fe0
[   15.544544] r10: 00000080  r9 : ef31d300  r8 : ef3e1e90
[   15.549744] r7 : ffc00000  r6 : 00000000  r5 : 00000080  r4 : ef3e1e50
[   15.556243] r3 : 00000000  r2 : 00000000  r1 : ffc00000  r0 : ef31d300
[   15.562744] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[   15.570022] Control: 10c5387d  Table: 2000406a  DAC: 00000015
[   15.575740] Process kworker/u16:0 (pid: 1061, stack limit = 0xef3e0240)
[   15.582325] Stack: (0xef3e1dcc to 0xef3e2000)
[   15.586661] 1dc0:                            00000080 00000000 ffc00000 ef3e1e90 ef31d300
[   15.594807] 1de0: 00000080 00000000 ef3e1e50 c0096430 ffc00000 00000000 ef264c6c 00000000
[   15.602952] 1e00: 00000000 00000000 00001000 00000000 ef264b80 ef264b80 ef264c6c c008e56c
[   15.611097] 1e20: 000200da 00000000 0009cae8 00000000 ef264b64 00000000 00000002 ef3e1e98
[   15.619242] 1e40: ef31d200 00000001 00000080 ef5f3fe0 ef3e1e90 00000001 00000000 00000080
[   15.627388] 1e60: 00000002 00000000 00000000 ef3e1f10 ef2ffc00 ed68b000 c0525bf0 ef200540
[   15.635533] 1e80: ef31d300 c00b5184 00000000 00000000 ef31d300 00000080 ef31d200 00000000
[   15.643679] 1ea0: 00000000 00000000 ef2ffc00 00000000 00000000 00000000 00000000 00000000
[   15.651824] 1ec0: 00000080 00000000 00000000 00000000 00000000 ef31d200 00000080 ef31d300
[   15.659970] 1ee0: ef3e1f10 c00b5c7c 00000000 00000000 00000000 ef3e0000 00000000 00000003
[   15.668115] 1f00: ef207000 ed68b000 ef200540 c00ba408 00000000 00000000 c0525bf0 ef31d300
[   15.676261] 1f20: ef3e0000 c00ba4c8 ef31d300 00000080 00000001 c00bb558 ed5b8044 ed5b8000
[   15.684406] 1f40: 00000000 ef2ffe3c 0000000e c0525a80 ef2005c0 ef204300 ef3e1f70 00000000
[   15.692552] 1f60: ffffffff ffffffff 00000000 c002e190 ffffffff ffffffff ffffffff ffffffff
[   15.700697] 1f80: 00000000 00000000 00000000 00000000 ef2005c0 c002e058 00000000 00000000
[   15.708842] 1fa0: 00000000 00000000 00000000 c000e778 00000000 00000000 00000000 00000000
[   15.716988] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   15.725133] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 54534f50 53455247
[   15.733286] Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8) 
[   15.739363] ---[ end trace c475e88e399c2384 ]---
[   15.743937] note: kworker/u16:0[1061] exited with preempt_count 1
[   15.754398] PVDD_ALIVE_1V0: 1000 mV 
[   15.757972] PVDD_APIO_1V8: 1800 mV 
[   15.761732] PVDD_APIO_MMCON_1V8: 1800 mV 
[   15.765535] PVDD_ADC_1V8: 1800 mV 
[   15.769357] PVDD_PLL_1V8: 1800 mV 
[   15.772605] PVDD_ANAIP_1V0: 1000 mV 
[   15.776177] PVDD_ANAIP_1V8: 1800 mV 
[   15.779638] PVDD_ABB_1V8: 1800 mV 
[   15.783607] PVDD_USB_3V3: 3000 mV 
[   15.787358] PVDD_PRE_1V8: 1800 mV 
[   15.790983] PVDD_USB_1V0: 1000 mV 
[   15.794147] PVDD_HSIC_1V8: 1800 mV 
[   15.797680] PVDD_APIO_MMCOFF_2V8: 2800 mV 
[   15.801765] LDO14: at 3000 mV 
[   15.804719] PVDD_PERI_2V8: 3300 mV 
[   15.808329] PVDD_PERI_3V3: 2200 mV 
[   15.811770] LDO17: at 3300 mV 
[   15.814695] PVDD_EMMC_1V8: 1800 mV 
[   15.818224] PVDD_TFLASH_2V8: 2800 mV 
[   15.821858] PVDD_BTWIFI_1V8: 1800 mV 
[   15.825458] PVDD_CAM1IO_1V8: 1800 mV 
[   15.829055] LDO22: at 1200 mV 
[   15.833821] PVDD_MIFS_1V1: ramp_delay not set
[   15.837308] PVDD_MIFS_1V1: 1200 mV 
[   15.841486] PVDD_CAM1_AVDD_2V8: 2800 mV 
[   15.845374] LDO25: at 1800 mV 
[   15.848331] PVDD_CAM0_AF_2V8: 3000 mV 
[   15.854017] PVDD_G3DS_1V0: ramp_delay not set
[   15.857044] PVDD_G3DS_1V0: 1200 mV 
[   15.861697] PVDD_TSP_3V3: 3300 mV 
[   15.864978] PVDD_AUDIO_1V8: 1800 mV 
[   15.868596] LDO30: at 1800 mV 
[   15.871638] PVDD_PERI_1V8: 1800 mV 
[   15.875038] PVDD_LCD_1V8: 1800 mV 
[   15.878557] PVDD_CAM0IO_1V8: 1800 mV 
[   15.882191] LDO34: at 3000 mV 
[   15.886616] PVDD_CAM0_DVDD_1V2: 1200 mV 
[   15.890292] LDO36: at 1800 mV 
[   15.893356] LDO37: at 1800 mV 
[   15.896510] PVDD_CAM0_AVDD_2V8: 2800 mV 
[   15.900810] PVDD_MIF_1V1: 800 <--> 1100 mV at 1100 mV 
[   15.906242] vdd_arm: 800 <--> 1000 mV at 1000 mV 
[   15.911297] PVDD_INT_1V0: 800 <--> 1000 mV at 1000 mV 
[   15.916211] PVDD_G3D_1V0: 800 <--> 1000 mV at 1000 mV 
[   15.921775] PVDD_LPDDR3_1V2: 800 <--> 1200 mV at 1200 mV 
[   15.927470] PVDD_KFC_1V0: 800 <--> 1000 mV at 1000 mV 
[   15.932899] VIN_LLDO_1V4: 800 <--> 1400 mV at 900 mV 
[   15.938260] VIN_MLDO_2V0: 800 <--> 2000 mV at 1225 mV 
[   15.943694] VIN_HLDO_3V5: 3000 <--> 3500 mV at 5000 mV 
[   15.949961] PVDD_EMMCF_2V8: 2800 mV 
[   15.954926] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[   15.962780] sdhci: Secure Digital Host Controller Interface driver
[   15.968352] sdhci: Copyright(c) Pierre Ossman
[   15.972855] Synopsys Designware Multimedia Card Interface Driver
[   15.979490] dwmmc_exynos 12200000.mmc: num-slots property not found, assuming 1 slot is available
[   15.987978] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[   15.993678] dwmmc_exynos 12200000.mmc: Version ID is 250a
[   15.999335] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107, 64 bit host data width, 64 deep fifo
[   16.008644] of_get_named_gpiod_flags: can't parse gpios property of node '/mmc@12200000[0]'
[   16.016894] of_get_named_gpiod_flags: can't parse gpios property of node '/mmc@12200000[0]'
[   16.055352] dwmmc_exynos 12200000.mmc: 1 slots initialized
[   16.059669] dwmmc_exynos 12220000.mmc: num-slots property not found, assuming 1 slot is available
[   16.068862] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[   16.074688] dwmmc_exynos 12220000.mmc: Version ID is 250a
[   16.083359] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109, 64 bit host data width, 64 deep fifo
[   16.091554] of_get_named_gpiod_flags: can't parse gpios property of node '/mmc@12220000[0]'
[   16.099827] of_get_named_gpiod_flags: can't parse gpios property of node '/mmc@12220000[0]'
[   16.135350] dwmmc_exynos 12220000.mmc: 1 slots initialized
[   16.141457] usbcore: registered new interface driver usbhid
[   16.145611] mmc0: BKOPS_EN bit is not set
[   16.150051] usbhid: USB HID core driver
[   16.153971] TCP: cubic registered
[   16.156767] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[   16.166733] NET: Registered protocol family 17
[   16.171560] NET: Registered protocol family 15
[   16.175264] Registering SWP/SWPB emulation handler
[   16.180612] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[   16.191281] mmc0: new DDR MMC card at address 0001
[   16.195414] platform 12000000.dwc3: Driver dwc3 requests probe deferral
[   16.202129] platform 12400000.dwc3: Driver dwc3 requests probe deferral
[   16.207940] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB 
[   16.212535] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB
[   16.218491] of_get_named_gpiod_flags: can't parse gpios property of node '/usb@12110000[0]'
[   16.226696] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB
[   16.232446] exynos-ehci 12110000.usb: no usb2 phy configured
[   16.238180] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB
[   16.243800] platform 12110000.usb: Driver exynos-ehci requests probe deferral
[   16.252204] of_get_named_gpiod_flags exited with status 0
[   16.256327]  mmcblk0: p1 p2 p3 p4
[   16.259497] Unhandled fault: external abort on non-linefetch (0x008) at 0xf00b8088
[   16.267035] Internal error: : 8 [#2] PREEMPT SMP ARM
[   16.271970] Modules linked in:
[   16.275007] CPU: 0 PID: 6 Comm: kworker/u16:0 Tainted: G      D       3.15.0-08884-g2dc24b0 #1
[   16.283590] Workqueue: kmmcd mmc_rescan
[   16.287396] task: ef014000 ti: ef0b4000 task.ti: ef0b4000
[   16.292773] PC is at rescan_partitions+0xb4/0x290
[   16.297447] LR is at 0xf00b8000
[   16.300569] pc : [<c01afcd8>]    lr : [<f00b8000>]    psr: 20000113
[   16.300569] sp : ef0b5c80  ip : 00000000  fp : 00000000
[   16.312005] r10: 00000000  r9 : ef2f3040  r8 : ed6ff200
[   16.317205] r7 : 00000000  r6 : eec24280  r5 : 00000000  r4 : 00000008
[   16.323704] r3 : 00000013  r2 : 00000000  r1 : 00000000  r0 : 00000001
[   16.330204] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[   16.337482] Control: 10c5387d  Table: 2000406a  DAC: 00000015
[   16.343201] Process kworker/u16:0 (pid: 6, stack limit = 0xef0b4240)
[   16.349527] Stack: (0xef0b5c80 to 0xef0b6000)
[   16.353864] 5c80: c054c214 00000001 ef0b4000 c0387150 00000001 c05284f8 ed577598 c05283c8
[   16.362008] 5ca0: eec24380 ed577468 eec24330 eec24280 00000000 ed577468 00000000 00000000
[   16.370153] 5cc0: 00000000 eec24280 ed6ff200 eec24290 00000001 00000000 00000000 c00e305c
[   16.378298] 5ce0: c00e19fc 00000000 00000000 00000001 eec24280 00000000 ed6ff270 ed6ff20c
[   16.386443] 5d00: 00000000 ed577380 00000003 c00e32c0 c052a6cc 00000001 00000003 c0388418
[   16.394589] 5d20: c052a6cc c00e1fcc ef0b5d34 c02222ec ed6ff240 00000001 eec24280 ed6ff200
[   16.402734] 5d40: ed6ff270 ed6ff20c 00000000 ed577380 00000003 c01adbf0 c01aca44 ed6ff200
[   16.410881] 5d60: 00000080 0b300000 00000002 ef2f8c00 ef2fec00 ef2f9800 ef2f9800 ef2f9abc
[   16.419026] 5d80: c02baca8 ef2fec00 ef2f9800 ef2fed88 ef0b5dd6 c02bbbac 00000056 ef2fec6c
[   16.427171] 5da0: 00000003 ef2f8c00 ef2fec00 c02bc7dc 00000003 ef0b5dd6 00000008 ed63d708
[   16.435317] 5dc0: c046a0a8 ef2f9a98 00000000 34362e33 42694720 32310000 694b2038 c0000042
[   16.443462] 5de0: 00000001 ef2fec08 c058de1c 00000000 c054c19c 00000001 00000000 c054be48
[   16.451607] 5e00: ef013c00 c02b112c c02b1114 c0225d90 00000000 ef2fec08 c0225f40 ef2f8808
[   16.459753] 5e20: 00000000 c022456c ef351698 ef203b44 ef2fec08 ef2fec3c c054bd68 c0225c6c
[   16.467898] 5e40: ef2fec08 ef2fec08 c054bd68 c02253dc ef2fec08 00000000 ef2fec10 c0223a44
[   16.476044] 5e60: ef013c00 c0381094 c047d27c ef0b5e84 00061a80 ef2fec00 ef2fec08 c047d228
[   16.484190] 5e80: 00061a80 c03b10ac 00000000 c02b154c c047d228 c0452000 c047d1e4 00000001
[   16.492335] 5ea0: ef2f8800 00000000 ef2f8800 c02b3f98 00061a80 40ff8080 ~$off
# PYBOOT: Exception: kernel: ERROR: failed to boot: Unhandled fault
# PYBOOT: Time: 38.45 seconds.
# PYBOOT: Result: FAIL
