Dear Fathi Boudra,

Thanks for your prompt reply.

I saw all of your e-mails. I am doing again with correct words as you suggested. I think, I was overlook the statements earlier as it was there /dev/sdX only.

I will let you know, once I complete it either it is success / failure / any issues.

Thanks again for your information.

Regards,
Srinivas G

On Thu, Aug 9, 2012 at 12:54 PM, Fathi Boudra <fathi.boudra@linaro.org> wrote:
On 9 August 2012 10:06, Srinivas Ganji <srinivasganji.android@gmail.com> wrote:
> Dear Fathi Boudra,
>
> Thank you very much for your e-mails with explanations. I will go through
> it, surely. But, I have a basic question. Who will create the partitions on
> SD card? I did not create myself. I thought that your commands only create.

The dd command will take care of the partitions.

> I think, in STEP-3, I need to pass /dev/sdb instead of /dev/sdb1. Is this
> correct?

This is correct. I sent a second mail right after to raise the step 3 issue.

> Please let me know about the creation of the partitions in SD card.
>
> Thanks a lot.
>
> Regards,
> Srinivas G.
>
>
> On Thu, Aug 9, 2012 at 12:11 PM, Fathi Boudra <fathi.boudra@linaro.org>
> wrote:
>>
>> On 8 August 2012 19:02, Zach Pfeffer <zach.pfeffer@linaro.org> wrote:
>> > Srinivas,
>> >
>> > Please use the instructions on:
>> >
>> >
>> > https://android-build.linaro.org/builds/~linaro-android/panda-ics-gcc47-tilt-tracking-blob-12.07-release/
>>
>> Those instructions are incomplete. They don't contain the binaries
>> section.
>>
>> @Srinivas: the instructions on releases.linaro.org are correct. I
>> pointed your mistakes in previous e-mails. Let me know if you need
>> further help.
>>
>> > On 8 August 2012 10:21, Srinivas Ganji <srinivasganji.android@gmail.com>
>> > wrote:
>> >> Hi All,
>> >>
>> >> We have a Pandaboard ES model with us. We purchased the same last week.
>> >> We
>> >> want to test board with the pre-built images from Linaro. So, we
>> >> followed
>> >> the following steps.
>> >>
>> >> The main link is
>> >>
>> >> http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-blob/
>> >>
>> >> STEPS:
>> >>
>> >> 1) wget
>> >>
>> >> http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-blob/panda-ics-gcc47-tilt-stable-blob.img.gz
>> >> 2) gunzip panda-ics-gcc47-tilt-stable-blob.img.gz
>> >> 3) sudo dd bs=4M if=panda-ics-gcc47-tilt-stable-blob.img of=/dev/sdb1
>> >> 4) wget
>> >>
>> >> http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-blob/install-binaries.sh
>> >> 5) chmod a+x install-binaries.sh
>> >> 6) ./install-binaries.sh /dev/sdb1
>> >>
>> >> After doing above steps, we inserted the SD card into the Pandaboard.
>> >> We
>> >> also connected other peripherals like HDMI cable, USB Mouse, USB
>> >> Keyboard,
>> >> Serial cable. The other end (DVI) is connected to the LED monitor.
>> >> After
>> >> every thing is connected correctly, we connected the power cable.
>> >> However,
>> >> we did not see any thing (display) in the LED monitor as well as Hyper
>> >> terminal.
>> >>
>> >> Are we missing any thing here? Are we followed the correct steps?
>> >>
>> >> Is the step-6 correct? Actually, it looks as follows.
>> >> $./install-binaries.sh /dev/sdX2 "device node of system partition"
>> >>
>> >> But, I do not understand about "device node of system partition".
>> >>
>> >> Please suggest us.
>> >>
>> >> Regards,
>> >> Srinivas G
>> >>
>> >> The output of the STEP-6.
>> >>
>> >> vendor/
>> >> vendor/imgtec/
>> >> vendor/imgtec/panda/
>> >> vendor/imgtec/panda/BoardConfigPanda.mk
>> >> vendor/imgtec/panda/proprietary/
>> >> vendor/imgtec/panda/proprietary/libsrv_init.so
>> >> vendor/imgtec/panda/proprietary/gralloc.omap4.so
>> >> vendor/imgtec/panda/proprietary/libsrv_um.so
>> >> vendor/imgtec/panda/proprietary/libIMGegl.so
>> >> vendor/imgtec/panda/proprietary/libEGL_POWERVR_SGX540_120.so
>> >> vendor/imgtec/panda/proprietary/libGLESv2_POWERVR_SGX540_120.so
>> >> vendor/imgtec/panda/proprietary/pvrsrvinit
>> >> vendor/imgtec/panda/proprietary/libGLESv1_CM_POWERVR_SGX540_120.so
>> >> vendor/imgtec/panda/proprietary/libusc.so
>> >> vendor/imgtec/panda/proprietary/libPVRScopeServices.so
>> >> vendor/imgtec/panda/proprietary/libpvr2d.so
>> >> vendor/imgtec/panda/proprietary/libglslcompiler.so
>> >> vendor/imgtec/panda/proprietary/libpvrANDROID_WSEGL.so
>> >> vendor/imgtec/panda/device-panda.mk
>> >> vendor/ti/
>> >> vendor/ti/panda/
>> >> vendor/ti/panda/BoardConfigVendor.mk
>> >> vendor/ti/panda/device-vendor.mk
>> >>
>> >> Files extracted successfully.
>> >> mount: you must specify the filesystem type
>> >> cp: cannot create regular file `/mnt/bin/pvrsrvinit': No such file or
>> >> directory
>> >> cp: cannot create regular file `/mnt/vendor/lib/hw/gralloc.omap4.so':
>> >> No
>> >> such file or directory
>> >> umount2: Invalid argument
>> >> umount: /dev/sdb1: not mounted
>> >> /home/pandriod/Android
>> >> Success, installing binary files
>> >>
>> >>
>> >>
>> >> _______________________________________________
>> >> linaro-android mailing list
>> >> linaro-android@lists.linaro.org
>> >> http://lists.linaro.org/mailman/listinfo/linaro-android
>> >>
>> >
>> >
>> >
>> > --
>> > Zach Pfeffer
>> > Android Platform Team Lead, Linaro Platform Teams
>> > Linaro.org | Open source software for ARM SoCs
>> > Follow Linaro: http://www.facebook.com/pages/Linaro
>> > http://twitter.com/#!/linaroorg - http://www.linaro.org/linaro-blog
>> >
>> > _______________________________________________
>> > linaro-android mailing list
>> > linaro-android@lists.linaro.org
>> > http://lists.linaro.org/mailman/listinfo/linaro-android
>>
>>
>>
>> --
>> Fathi Boudra
>> Linaro Release Manager | Validation Project Manager
>> Linaro.org | Open source software for ARM SoCs
>
>



--
Fathi Boudra
Linaro Release Manager | Validation Project Manager
Linaro.org | Open source software for ARM SoCs