Vishal

On 21 October 2012 01:19, Josep Soms <josep.soms@lefthome.net> wrote:

Hello Michael,

Thank you very much for your help.

Unfortunately there are no instructions for this in the download page of the prebuild image (landing-panda.img is the only file mentioned in this section):

Using pre-built image

# Insert SD card and note the assigned '/dev/sdX' or '/dev/mmcblk0'
$ dmesg

$ SDCARD=/dev/sdX # sdcard found from dmesg above
$ URL=http://releases.linaro.org/12.01/android/images/landing-panda/landing-panda.img.gz
$ curl $URL | gunzip -c | sudo dd bs=64k of=$SDCARD
Note: Windows users may use the Image Writer for Windows

It would be very much appreciated if you could provide more detailed instructions about this on next working day in the office.......

Sorry for my poor know-how about image writing.

Have a nice Sunday.

Josep

-----Mensaje original----- From: Michael Trimarchi
Sent: Saturday, October 20, 2012 9:14 PM

To: Josep Soms
Cc: Vishal Bhoj
Subject: Re: Pandaboard ES platform issues.

Hi

Josep Soms <josep.soms@lefthome.net> ha scritto:

Hello Michael,

Thank you very much for your help.

Where can I get the correct version of the opengl binary ?
Please could you confirm in which partition of SD-Card should I push it
?

The correct version is always in the download page of the prebuild image. I'm
with mobile and I can't help.

Michael

Thanks,
Josep

-----Mensaje original----- From: Michael Trimarchi
Sent: Saturday, October 20, 2012 8:42 PM
To: Josep Soms
Cc: Vishal Bhoj
Subject: Re: Pandaboard ES platform issues.

Hi

Josep Soms <josep.soms@lefthome.net> ha scritto:

Dear Michael,

Thank you very much for your help.

I think opengl should be included in the prebuilt image, shouldn't it

?

In other case, please could you let me know how to add opengl binary

to

the
prebuilt image on the SD-Card with Win32 Disk Imager ?

You can try using adb and push in the correct position

Michael

Thanks,
Josep

-----Mensaje original----- From: Michael Trimarchi
Sent: Saturday, October 20, 2012 8:11 PM
To: Vishal Bhoj ; Josep Soms
Cc: linaro-android@lists.linaro.org
Subject: Re: Pandaboard ES platform issues.

Hi

Vishal Bhoj <vishal.bhoj@linaro.org> ha scritto:

Hi Josep,

Can you please point the link from where you fetched the images and

the

installation instructions ?

Also Can you run the command "logcat" once the device is booted up

and

share the logs. That will be more helpful to debug the issue.

I think that you don't install the binary for
the opengl.

Michael

Regards,
Vishal

On 20 October 2012 23:31, Josep Soms <josep.soms@lefthome.net> wrote:

Dear Vishal,

>From the Linaro mailing list, I think you are the expert for

Pandaboard ES

platform issues.

So your help for this problem would be very much appreciated:

I am just getting started with Android prebuilt images on

Pandaboard

ES

platform, but I don’t have success with any prebuilt image

available

on

your download section.
As I’m not a Linux expert, prebuilt images are written on SD-Card

with

Win32 Disk Imager.

- Several prebuild images tested, but Android does not work with

any

of

them.
- 2 diferent boards tested, but unfortunately the result is the

same

(even

hadware validation is ok for both boards).

It has been observed the top of OMAP4460 device is getting very

hot,

so

the board has been powered off in order to avoid any hardware

damage.

Several error messages on the terminal, unable to analyze all of

them

one

by one.

Please could you help me ?

Thanks,
Josep

P.D. For example, there are some of the error messages:

[ 2751.705169] acc_open
[ 2751.707946] acc_release
[ 2752.743469] omap_alert_zone:hot spot temp 101092
[ 2752.768890] binder: release 31777:31777 transaction 483178 in,

still

active
[ 2752.776489] binder: send failed reply for transaction 483178 to
31918:31918
[ 2752.784301] binder: release 31777:31789 transaction 483160 in,

still

active
[ 2752.791687] binder: send failed reply for transaction 483160 to
31891:31957
[ 2752.799468] binder: release 31777:31949 transaction 483141 in,

still

active
[ 2752.806884] binder: send failed reply for transaction 483141 to
31891:31891
[ 2752.814392] binder: release 31777:31950 transaction 483176 in,

still

active
[ 2752.821899] binder: send failed reply for transaction 483176 to
31879:31879
[ 2752.829681] binder: send failed reply for transaction 483179 to
31911:31911
[ 2752.837188] binder: send failed reply for transaction 483186 to
31958:31958
[ 2752.844848] binder: 31851:31851 transaction failed 29189, size

156-0

[ 2752.853607] binder: 31879:31879 transaction failed 29189, size

292-8

[ 2752.877990] binder: 31891:31891 transaction failed 29189, size

224-4

[ 2752.884735] binder: 31851:31851 transaction failed 29189, size

100-0

[ 2752.917663] binder: 31851:31851 transaction failed 29189, size

5348-4

[ 2753.003082] alarm_release: clear alarm, pending 0
[ 2753.008209] alarm_release: clear alarm, pending 0
[ 2753.243499] omap_monitor_zone:hot spot temp 94279
[ 2754.050354] request_suspend_state: wakeup (0->0) at

2754024597173

(2000-01-01 00:45:50.002624484 UTC)
[ 2754.074890] init: untracked pid 31751 exited
[ 2754.079956] init: untracked pid 31750 exited
[ 2754.084747] init: untracked pid 31879 exited
[ 2754.089416] init: untracked pid 31891 exited
[ 2754.094390] init: untracked pid 31958 exited
[ 2754.105621] init: untracked pid 31863 exited
[ 2760.588409] request_suspend_state: wakeup (0->0) at

2760562622075

(2000-01-01 00:45:56.540649386 UTC)
[ 2761.124206] acc_open
[ 2761.126556] acc_release

------------------------------------------------------------------------

_______________________________________________
linaro-android mailing list
linaro-android@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-android

--
Sent from my Android phone with K-9 Mail. Please excuse my brevity.