+ Linaro Android Mailing List
On Fri, Nov 22, 2013 at 7:44 PM, Botao Sun botao.sun@linaro.org wrote:
Hi Vishal,
Do you think we need a bug in Launchpad to track this issue?
Thanks.
Best Regards Botao Sun
On Fri, Nov 22, 2013 at 5:38 PM, Soumya Basak soumya.basak@linaro.orgwrote:
Hi Botao, I have checked twice the image with panda 4460 board:
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
- basically, when eth0 cable is plugged in hw, and wifi is not turned on
from UI, # busybox ifconfig -a not shown the wlan0 only eth0 up and accessing network. 2. when you turn on wifi it will ask you password, after assign password, wifi shown connected (but inactive), # busybox ifconfig -a shown the wlan0 candidate but no inet address, and mask. 3. when unplugged the eth0, wlan0 is get inet address and musk, and connected.
on the other hand wifi is working well, there is no issue with Youtube playback, or enable from UI, after assign Password.
so, both are not up at the same time.
this stuff is observed from since Android version: 4.3
@Botao, what is your opinion ?
Thank You. Best Regards Soumya Basak.
On 21 November 2013 20:40, Botao Sun botao.sun@linaro.org wrote:
OK, with more tests, the problem is, if no Ethernet cable attached, WiFi works, otherwise, it shows the error I mentioned in previous 2 emails.
root@pandaboard:/ # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 0E:60:CF:E5:49:01 UP BROADCAST RUNNING MULTICAST MTU:1488 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:2510 (2.4 KiB)
ip6tnl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1452 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
sit0 Link encap:UNSPEC HWaddr 00-00-00-00-0F-00-01-00-00-00-00-00-00-00-00-00 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0 Link encap:Ethernet HWaddr 0E:20:CF:E5:49:01 inet addr:10.0.0.25 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:96 errors:0 dropped:0 overruns:0 frame:0 TX packets:105 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97780 (95.4 KiB) TX bytes:14813 (14.4 KiB)
root@pandaboard:/ #
Is it a "work-as-design" stuff or a bug? If we keep it likes this, then in order to test WiFi, I have to disable Ethernet first, then restore it after the test is done.
Thanks.
Best Regards Botao Sun
On Fri, Nov 22, 2013 at 2:02 AM, Botao Sun botao.sun@linaro.org wrote:
Hi Soumya,
The WiFi doesn't work on 13.10 release image either:
https://android-build.linaro.org/builds/~linaro-android-member-ti/panda-lina...
On my TI Panda 4460 board, same behaviour observed, and following output shows:
[ 148.630249] wl1271: loaded [ 149.538604] wl1271: firmware booted (Rev 6.3.0.0.77) [ 149.556671] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 250.320129] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 250.383636] wl1271: Association completed. [ 251.542541] cfg80211: Calling CRDA to update world regulatory domain [ 261.064025] wl1271: Scan completed due to error. [ 261.069000] wl1271: Reading FW panic log [ 261.074127] wl1271: Hardware recovery in progress. FW ver: Rev 6.3.0.0.77 pc: 0x0 [ 261.074127] wl1271: down [ 261.086059] ieee80211 phy0: Hardware restart was requested [ 261.714691] wl1271: firmware booted (Rev 6.3.0.0.77)
Would you double check it on your side? Based on the output of "ifconfig", there is no IP assigned to wlan0 interface:
root@pandaboard:/ # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 0E:60:CF:E5:49:01 inet addr:10.0.0.24 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1488 Metric:1 RX packets:34 errors:0 dropped:2 overruns:0 frame:0 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3870 (3.7 KiB) TX bytes:1901 (1.8 KiB)
ip6tnl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1452 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
sit0 Link encap:UNSPEC HWaddr 00-00-00-00-0F-00-01-00-00-00-00-00-00-00-00-00 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0 Link encap:Ethernet HWaddr 0E:20:CF:E5:49:01 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:607 (607.0 B) TX bytes:655 (655.0 B)
root@pandaboard:/ #
Thanks.
Best Regards Botao Sun
On Fri, Nov 22, 2013 at 12:40 AM, Botao Sun botao.sun@linaro.orgwrote:
Hi Soumya,
Please take a look at WiFi status on TI Panda 4460, with Linaro Android build 479:
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
http://snapshots.linaro.org/android/~linaro-android-member-ti/panda-linaro/4...
You can use "wget" to download them in your local terminal if the web page can't be shown up.
I ask because I just found WiFi doesn't work via GUI on my side, following log shows in serial console:
[ 25.692474] wl1271: loaded [ 26.373870] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 27.608551] wl1271: firmware booted (Rev 6.3.0.0.77) [ 27.629058] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 29.750000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 29.803771] wl1271: Association completed. [ 29.951232] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit [ 30.969970] cfg80211: Calling CRDA to update world regulatory domain
The access point can be shown successfully in the list, and I can click and enter password as well, but then above output shows, with "Disabled" under the access point name on my screen.
Based on our test result spreadsheet, it should at least work on 13.10 release image. I'm going to try it soon.
Thanks.
Best Regards Botao Sun