U-Boot 2011.09-rc2 (Oct 21 2011 - 03:17:48) CPU: Freescale i.MX53 family rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO with MC34708 I2C: ready DRAM: 1 GiB WARNING: Caches not enabled CPU: Switch CPU clock to 1GHZ OK DDR: Switch DDR clock to 400MHz OK MMC: FSL_ESDHC: 0, FSL_ESDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: got MAC address from fuse: 00:04:9f:01:ab:94 FEC Hit any key to stop autoboot: 0 reading boot.scr 418 bytes read Running bootscript from mmc ... ## Executing script at 70800000 reading uImage 4204824 bytes read reading uInitrd 1864668 bytes read reading board.dtb 324 bytes read ## Booting kernel from Legacy Image at 70000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4204760 Bytes = 4 MiB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 72000000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 1864604 Bytes = 1.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 71ff0000 Booting using the fdt blob at 0x71ff0000 Loading Kernel Image ... OK OK Using Device Tree in place at 71ff0000, end 71ff3143 Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 3.1.0-1002-linaro-lt-mx5 (buildd@hubbard) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #13-Ubuntu PREEMPT Fri Dec 16 01:21:07 UTC 2011 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Freescale MX53 LOCO Board, model: Freescale i.MX53 LOCO [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 242688 [ 0.000000] Kernel command line: console=tty0 console=ttymxc0,115200n8 root=UUID=41c184b3-b844-4be7-a727-f9e95194e5ed rootwait ro [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 512MB 448MB = 960MB total [ 0.000000] Memory: 957416k/957416k available, 91160k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xf4000000 ( 312 MB) [ 0.000000] lowmem : 0x80000000 - 0xe0000000 (1536 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [ 0.000000] .text : 0x80008000 - 0x80807900 (8191 kB) [ 0.000000] .init : 0x80808000 - 0x80856000 ( 312 kB) [ 0.000000] .data : 0x80856000 - 0x808bb470 ( 406 kB) [ 0.000000] .bss : 0x808bb494 - 0x80e56574 (5741 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:400 [ 0.000000] TrustZone Interrupt Controller (TZIC) initialized [ 0.000000] sched_clock: 32 bits at 8MHz, resolution 125ns, wraps every 536870ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.003166] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) [ 0.090431] pid_max: default: 32768 minimum: 301 [ 0.090836] Security Framework initialized [ 0.090997] AppArmor: AppArmor initialized [ 0.091165] Mount-cache hash table entries: 512 [ 0.095575] CPU: Testing write buffer coherency: ok [ 0.095775] ftrace: allocating 22038 entries in 65 pages [ 0.123172] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.126727] devtmpfs: initialized [ 0.136674] print_constraints: dummy: [ 0.138375] NET: Registered protocol family 16 [ 0.195452] No ATAGs? [ 0.195490] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.197578] IMX usb wakeup probe [ 0.198177] IMX usb wakeup probe [ 0.264907] bio: create slab at 0 [ 0.270857] SCSI subsystem initialized [ 0.274664] usbcore: registered new interface driver usbfs [ 0.275551] usbcore: registered new interface driver hub [ 0.276251] usbcore: registered new device driver usb [ 0.285533] print_constraints: VDDA: 3200 mV [ 0.292871] print_constraints: DA9052_LDO1: 600 <--> 1800 mV at 1300 mV normal [ 0.294686] print_constraints: DA9052_LDO2: 600 <--> 1800 mV at 1300 mV normal [ 0.296417] print_constraints: DA9052_LDO3: 1725 <--> 3300 mV at 3300 mV normal [ 0.297972] print_constraints: DA9052_LDO4: 1725 <--> 3300 mV at 2775 mV normal [ 0.299553] print_constraints: DA9052_LDO5: 1200 <--> 3600 mV at 1300 mV normal [ 0.301061] print_constraints: DA9052_LDO6: 1200 <--> 3600 mV at 1300 mV normal [ 0.302666] print_constraints: DA9052_LDO7: 1200 <--> 3600 mV at 2750 mV normal [ 0.304647] print_constraints: DA9052_LDO8: 1200 <--> 3600 mV at 1800 mV normal [ 0.306181] print_constraints: DA9052_LDO9: 1250 <--> 3650 mV at 1500 mV normal [ 0.307753] print_constraints: DA9052_LDO10: 1200 <--> 3600 mV at 1300 mV normal [ 0.309264] print_constraints: DA9052_BUCK_CORE: 500 <--> 2075 mV at 1250 mV normal [ 0.310832] print_constraints: DA9052_BUCK_PRO: 500 <--> 2075 mV at 1350 mV normal [ 0.312345] print_constraints: DA9052_BUCK_MEM: 925 <--> 2500 mV at 1500 mV normal [ 0.314148] print_constraints: DA9052_BUCK_PERI: 925 <--> 2500 mV at 2475 mV normal [ 0.343464] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.347487] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.350724] NetLabel: Initializing [ 0.350770] NetLabel: domain hash size = 128 [ 0.350795] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.351062] NetLabel: unlabeled traffic allowed by default [ 0.351156] Switching to clocksource mxc_timer1 [ 0.353496] Switched to NOHz mode on CPU #0 [ 0.411087] AppArmor: AppArmor Filesystem Enabled [ 0.466564] NET: Registered protocol family 2 [ 0.467129] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.468669] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.471167] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes) [ 0.500938] TCP: Hash tables configured (established 131072 bind 65536) [ 0.501104] TCP reno registered [ 0.501157] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.501708] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.502807] NET: Registered protocol family 1 [ 0.504072] RPC: Registered named UNIX socket transport module. [ 0.504127] RPC: Registered udp transport module. [ 0.504158] RPC: Registered tcp transport module. [ 0.504186] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.504880] Trying to unpack rootfs image as initramfs... [ 0.637556] Freeing initrd memory: 1820K [ 0.639156] Bus freq driver module loaded [ 0.639706] sdram autogating driver module loaded [ 0.640084] i.MXC CPU frequency driver [ 0.641805] DVFS driver module loaded [ 0.644549] audit: initializing netlink socket (disabled) [ 0.644862] type=2000 audit(0.610:1): initialized [ 0.725395] Kprobe smoke test started [ 0.742641] Kprobe smoke test passed successfully [ 0.773235] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.776083] Btrfs loaded [ 0.776186] msgmni has been set to 1873 [ 0.779865] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.780055] io scheduler noop registered [ 0.780089] io scheduler deadline registered [ 0.780246] io scheduler cfq registered (default) [ 0.786086] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi [ 0.934787] sii902x 1-0039: found device 9022 [ 0.972273] sii902x 1-0039: Can not read edid [ 0.972335] fbcvt: 1920x1080@60: CVT Name - 2.073M9 [ 0.974321] imx-ipuv3 imx-ipuv3.0: Channel already disabled 9 [ 0.974339] imx-ipuv3 imx-ipuv3.0: Channel already uninitialized 9 [ 1.001319] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) [ 1.068130] Console: switching to colour frame buffer device 240x67 [ 1.085008] imx-ipuv3 imx-ipuv3.0: Channel already disabled 10 [ 1.085024] imx-ipuv3 imx-ipuv3.0: Channel already uninitialized 10 [ 1.088220] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver vga [ 1.088600] _regulator_get: get() with no identifier [ 1.089242] imx-ipuv3 imx-ipuv3.0: Channel already disabled 7 [ 1.089261] imx-ipuv3 imx-ipuv3.0: Channel already uninitialized 7 [ 1.098241] imx-sdma imx35-sdma: loaded firmware 1.0 [ 1.117594] imx-sdma imx35-sdma: initialized [ 1.119351] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.201859] Serial: IMX driver [ 1.202418] imx21-uart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a IMX [ 1.943333] console [ttymxc0] enabled [ 1.989975] brd: module loaded [ 2.010356] loop: module loaded [ 2.015936] ahci: SSS flag set, parallel bus scan disabled [ 2.022074] ahci imx53-ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.030691] ahci imx53-ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc [ 2.043692] scsi0 : ahci_platform [ 2.049350] ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 28 [ 2.062619] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.075657] FEC Ethernet Driver [ 2.096584] fec_enet_mii_bus: probed [ 2.104259] usbcore: registered new interface driver asix [ 2.110298] usbcore: registered new interface driver cdc_ether [ 2.116908] usbcore: registered new interface driver smsc95xx [ 2.123425] usbcore: registered new interface driver net1080 [ 2.129681] usbcore: registered new interface driver cdc_subset [ 2.136204] usbcore: registered new interface driver zaurus [ 2.142213] cdc_ncm: 04-Aug-2011 [ 2.145924] usbcore: registered new interface driver cdc_ncm [ 2.153502] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.261274] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 2.270967] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 1 [ 2.301332] fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200 [ 2.321312] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 2.328003] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.334998] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.346650] usb usb1: Product: Freescale On-Chip EHCI Host Controller [ 2.357240] usb usb1: Manufacturer: Linux 3.1.0-1002-linaro-lt-mx5 ehci_hcd [ 2.368360] usb usb1: SerialNumber: fsl-ehci.1 [ 2.381651] hub 1-0:1.0: USB hub found [ 2.389798] hub 1-0:1.0: 1 port detected [ 2.401363] ata1: SATA link down (SStatus 0 SControl 300) [ 2.521277] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 2.533493] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 2 [ 2.571310] fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000 [ 2.591250] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 2.601459] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.612447] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.623842] usb usb2: Product: Freescale On-Chip EHCI Host Controller [ 2.634437] usb usb2: Manufacturer: Linux 3.1.0-1002-linaro-lt-mx5 ehci_hcd [ 2.645549] usb usb2: SerialNumber: fsl-ehci.0 [ 2.656449] hub 2-0:1.0: USB hub found [ 2.664639] hub 2-0:1.0: 1 port detected [ 2.675360] usbcore: registered new interface driver cdc_wdm [ 2.685405] Initializing USB Mass Storage driver... [ 2.695093] usbcore: registered new interface driver usb-storage [ 2.705462] USB Mass Storage support registered. [ 2.715632] usbcore: registered new interface driver libusual [ 2.726412] usbcore: registered new interface driver usbtest [ 2.739461] mxc_rtc mxc_rtc.0: hardware module can't be enabled! [ 2.750178] mxc_rtc: probe of mxc_rtc.0 failed with error -5 [ 2.764458] mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc0 [ 2.776154] i2c /dev entries driver [ 2.787672] Linux video capture interface: v2.00 [ 2.798923] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16 [ 2.811990] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 [ 2.824672] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18 [ 2.836953] Driver for 1-wire Dallas network protocol. [ 2.849447] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) [ 2.864340] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com [ 2.878133] cpuidle: using governor ladder [ 2.886660] cpuidle: using governor menu [ 2.895849] sdhci: Secure Digital Host Controller Interface driver [ 2.906476] sdhci: Copyright(c) Pierre Ossman [ 2.915080] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.925923] mmc0: no vmmc regulator found [ 2.937065] mmc0: SDHCI controller on sdhci-esdhc-imx53.0 [sdhci-esdhc-imx53.0] using DMA [ 2.950722] mmc1: no vmmc regulator found [ 2.960750] mmc1: SDHCI controller on sdhci-esdhc-imx53.2 [sdhci-esdhc-imx53.2] using DMA [ 3.076148] VPU initialized [ 3.234344] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.364682] usbcore: registered new interface driver usbhid [ 3.375625] usbhid: USB HID core driver [ 3.390040] mxc_spdif mxc_spdif.0: MXC SPDIF Audio [ 3.408166] sgtl5000 1-000a: Failed to get supply 'VDDD': -19 [ 3.418922] mmc0: new SDHC card at address e624 [ 3.430030] print_constraints: 1-000a: 850 <--> 1600 mV at 1200 mV normal [ 3.444375] mmcblk0: mmc0:e624 SU04G 3.69 GiB [ 3.454454] sgtl5000 1-000a: Using internal LDO instead of VDDD [ 3.472862] mmcblk0: p1 p2 p3 [ 3.483446] sgtl5000 1-000a: sgtl5000 revision 17 [ 3.510532] asoc: sgtl5000 <-> imx-ssi.1 mapping ok [ 3.625743] input: sgtl5000-audio Headphone Jack as /devices/platform/soc-audio/sound/card0/input0 [ 3.647939] asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok [ 3.661094] ALSA device list: [ 3.669068] #0: sgtl5000-audio [ 3.676915] #1: imx-spdif [ 3.685739] oprofile: using arm/armv7 [ 3.694963] TCP cubic registered [ 3.702851] Initializing XFRM netlink socket [ 3.712262] NET: Registered protocol family 10 [ 3.723837] IPv6 over IPv4 tunneling driver [ 3.734533] NET: Registered protocol family 17 [ 3.747584] NET: Registered protocol family 15 [ 3.756922] Registering the dns_resolver key type [ 3.866511] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 3.878896] ThumbEE CPU extension supported. [ 3.887676] Registering SWP/SWPB emulation handler [ 3.912335] regulator_init_complete: DA9052_BUCK_PERI: incomplete constraints, leaving on [ 3.925647] regulator_init_complete: DA9052_BUCK_MEM: incomplete constraints, leaving on [ 3.938338] regulator_init_complete: DA9052_BUCK_PRO: incomplete constraints, leaving on [ 3.950934] regulator_init_complete: DA9052_BUCK_CORE: incomplete constraints, leaving on [ 3.963602] regulator_init_complete: DA9052_LDO10: incomplete constraints, leaving on [ 3.975867] regulator_init_complete: DA9052_LDO9: incomplete constraints, leaving on [ 3.991314] regulator_init_complete: DA9052_LDO8: incomplete constraints, leaving on [ 4.003756] regulator_init_complete: DA9052_LDO7: incomplete constraints, leaving on [ 4.015813] regulator_init_complete: DA9052_LDO6: incomplete constraints, leaving on [ 4.127789] regulator_init_complete: DA9052_LDO5: incomplete constraints, leaving on [ 4.139844] regulator_init_complete: DA9052_LDO4: incomplete constraints, leaving on [ 4.151827] regulator_init_complete: DA9052_LDO3: incomplete constraints, leaving on [ 4.163751] regulator_init_complete: DA9052_LDO2: incomplete constraints, leaving on [ 4.175627] regulator_init_complete: DA9052_LDO1: incomplete constraints, leaving on [ 4.189780] input: gpio-keys as /devices/platform/gpio-keys/input/input1 [ 4.204158] mxc_rtc mxc_rtc.0: setting system clock to 1970-01-01 00:00:01 UTC (1) [ 4.219339] Freeing init memory: 312K Loading, please wait... [ 4.520125] udevd[727]: starting version 173 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 5.933433] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem [ 5.989533] EXT4-fs (mmcblk0p3): write access will be enabled during recovery [ 15.086102] EXT4-fs (mmcblk0p3): orphan cleanup on readonly fs [ 15.100238] EXT4-fs (mmcblk0p3): 10 orphan inodes deleted [ 15.110011] EXT4-fs (mmcblk0p3): recovery complete [ 15.155271] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. [ 15.784324] init: ureadahead main process (847) terminated with status 5 [ 19.650808] imx-ipuv3 imx-ipuv3.0: Channel already disabled 9 [ 19.650830] imx-ipuv3 imx-ipuv3.0: Channel already uninitialized 9 fsck from util-linux 2.19.1 rootfs: clean, 107125/193152 files, 421148/772096 blocks * Starting network connection manager[ OK ] * Starting CUPS printing spooler/server[ OK ] * Starting Bridge socket events into upstart[ OK ] * Stopping System V initialisation compatibility[ OK ] speech-dispatcher disabled; edit /etc/default/speech-dispatcher Checking for running unattended-upgrades: * Starting System V runlevel compatibility[ OK ] * Stopping automatic crash report generation[fail] * Starting restore sound card(s') mixer state(s)[ OK ] Last login: Thu Jan 1 00:04:43 UTC 1970 on tty1 * Starting LightDM Display Manager[ OK ] * Starting anac(h)ronistic cron[ OK ] * Starting save kernel messages[ OK ] * Starting restore sound card(s') mixer state(s)[fail] * Starting regular background program processing daemon[ OK ] [ OK ]rting bluetooth * PulseAudio configured for per-user sessions saned disabled; edit /etc/default/saned [ 31.795944] imx-ipuv3 imx-ipuv3.0: Channel already disabled 9 [ 31.795965] imx-ipuv3 imx-ipuv3.0: Channel already uninitialized 9 Login timed out after 60 seconds. Last login: Thu Jan 1 00:00:29 UTC 1970 on tty1 cat: /var/lib/update-notifier/fsck-at-reboot: No such file or directory run-parts: /etc/update-motd.d/98-fsck-at-reboot exited with return code 1 Welcome to Linaro 12.01 (GNU/Linux 3.1.0-1002-linaro-lt-mx5 armv7l) * Documentation: https://wiki.linaro.org/ 1 package can be updated. 0 updates are security updates. 1 package can be updated. 0 updates are security updates. 1 package can be updated. 0 updates are security updates. root@linaro-ubuntu-desktop:~#