On 19 May 2014 23:42, Roy Franz <roy.franz@linaro.org> wrote:
On Mon, Apr 28, 2014 at 8:46 AM, Ryan Harkin <ryan.harkin@linaro.org> wrote:
Booting UEFI for our 64 bit models/platforms has become more complex due to upstream changes.

You can build UEFI as per usual, however, before you can boot the .fd file, you will have to wrap it into a Firmware Image Package (aka FIP).

You will not be able to mix "old " and "new" versions of UEFI and TF.


--------------------------------------------------------------------------------
- Get the UEFI build tools
--------------------------------------------------------------------------------
PATH=$PATH:`pwd`/uefi-tools

--------------------------------------------------------------------------------
- Build UEFI for the FVP models
--------------------------------------------------------------------------------
git clone git://git.linaro.org/uefi/linaro-edk2.git
cd linaro-edk2
uefi-build fvp_minimal

This will give you a .fd file, such as:
./Build/ArmVExpress-FVP-AArch64/RELEASE_GCC48/FV/FVP_AARCH64_EFI.fd

You will then need to point the "BL33" environment variable to this file, eg:

export BL33=`pwd`/Build/ArmVExpress-FVP-AArch64/RELEASE_GCC48/FV/FVP_AARCH64_EFI.fd


--------------------------------------------------------------------------------
- Build the Trusted Firmware for FVP models
--------------------------------------------------------------------------------
git clone git://git.linaro.org/arm/arm-trusted-firmware.git
CROSS_COMPILE=aarch64-linux-gnu- make PLAT=fvp all fip

You will then have two important files:
./build/fvp/release/bl1.bin
./build/fvp/release/fip.bin


--------------------------------------------------------------------------------
- Boot the model
--------------------------------------------------------------------------------
Pass the bl1.bin and fip.bin files as parameters to the model.  Eg, this is how I booted my model:

/linaro/fastmodels/FVP_Base_AEMv8A-AEMv8A/models/Linux64_GCC-4.1/FVP_Base_AEMv8A-AEMv8A -C pctl.startup=0.0.0.0 -C bp.secure_memory=0 -C cluster0.NUM_CORES=1 -C cluster1.NUM_CORES=1 -C cache_state_modelled=0 -C bp.pl011_uart0.untimed_fifos=1 -C bp.secureflashloader.fname=./build/fvp/release/bl1.bin -C bp.flashloader0.fname=./build/fvp/release/fip.bin -C bp.virtioblockdevice.image_path=/linaro/releases/oe/14.04/fastmodel/sd.img -C bp.hostbridge.interfaceName=ARMryan -C bp.smsc_91c111.enabled=true -C bp.smsc_91c111.mac_address=00:02:f7:ef:67:e6


Of course, your installation path to the models and the location of your disk image will vary.

Hope this all helps,

Regards,
Ryan.


_______________________________________________
Linaro-uefi mailing list
Linaro-uefi@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-uefi



​Hi Ryan,

   This worked.  I though I had been running older trusted firmware that did not require the FIP packaging.

I had to use the bl1.bin that I built to get it to work - the bl1.bin binary I had downloaded did not work. Will I always
need to rebuild the bl1.bin when the EFI image changes?  I'm guess no, and that my problems were due to a  mismatch
of the bl1.bin and FIP packaging.


You don't need to rebuild BL1 each time.  The problem is not that tight.  Basically, if you have an old BL1 that loads UEFI directly, you will never be able to load a FIP.  And vice versa.  If you have a new BL1 that loads a FIP, you will never be able to load UEFI directly.

So, if you have the 1st ever "FIP enabled" BL1 binary, you should be able to build a FIP today, with a recent UEFI binary, and it should work fine.

You cannot put and old UEFI binary into the FIP.  And you cannot put a recent UEFI binary into NOR.

old UEFI binary == a binary built to be run from address 0x0
recent UEFI binary == a binary build to be copied to RAM by a loader and run from there

old BL1 == one that loads BL2 and BL31 from semihosting and UEFI from NOR
new BL1 == one that loads BL2, BL31 and UEFI from the FIP

Hope that helps.

 
Thanks,
Roy
​