The patch below does not apply to the 5.4-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From a808925075fb750804a60ff0710614466c396db4 Mon Sep 17 00:00:00 2001
From: Hongyu Xie <xy521521(a)gmail.com>
Date: Thu, 23 Jun 2022 14:19:42 +0300
Subject: [PATCH] xhci: Keep interrupt disabled in initialization until host is
running.
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable(a)kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 9ac56e9ffc64..cb99bed5f755 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -611,15 +611,37 @@ static int xhci_init(struct usb_hcd *hcd)
static int xhci_run_finished(struct xhci_hcd *xhci)
{
+ unsigned long flags;
+ u32 temp;
+
+ /*
+ * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+ * Protect the short window before host is running with a lock
+ */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+ temp = readl(&xhci->op_regs->command);
+ temp |= (CMD_EIE);
+ writel(temp, &xhci->op_regs->command);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+ temp = readl(&xhci->ir_set->irq_pending);
+ writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+
if (xhci_start(xhci)) {
xhci_halt(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
return -ENODEV;
}
+
xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
return 0;
}
@@ -668,19 +690,6 @@ int xhci_run(struct usb_hcd *hcd)
temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
writel(temp, &xhci->ir_set->irq_control);
- /* Set the HCD state before we enable the irqs */
- temp = readl(&xhci->op_regs->command);
- temp |= (CMD_EIE);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enable interrupts, cmd = 0x%x.", temp);
- writel(temp, &xhci->op_regs->command);
-
- temp = readl(&xhci->ir_set->irq_pending);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
- xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
- writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
-
if (xhci->quirks & XHCI_NEC_HOST) {
struct xhci_command *command;
The patch below does not apply to the 4.19-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From a808925075fb750804a60ff0710614466c396db4 Mon Sep 17 00:00:00 2001
From: Hongyu Xie <xy521521(a)gmail.com>
Date: Thu, 23 Jun 2022 14:19:42 +0300
Subject: [PATCH] xhci: Keep interrupt disabled in initialization until host is
running.
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable(a)kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 9ac56e9ffc64..cb99bed5f755 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -611,15 +611,37 @@ static int xhci_init(struct usb_hcd *hcd)
static int xhci_run_finished(struct xhci_hcd *xhci)
{
+ unsigned long flags;
+ u32 temp;
+
+ /*
+ * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+ * Protect the short window before host is running with a lock
+ */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+ temp = readl(&xhci->op_regs->command);
+ temp |= (CMD_EIE);
+ writel(temp, &xhci->op_regs->command);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+ temp = readl(&xhci->ir_set->irq_pending);
+ writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+
if (xhci_start(xhci)) {
xhci_halt(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
return -ENODEV;
}
+
xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
return 0;
}
@@ -668,19 +690,6 @@ int xhci_run(struct usb_hcd *hcd)
temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
writel(temp, &xhci->ir_set->irq_control);
- /* Set the HCD state before we enable the irqs */
- temp = readl(&xhci->op_regs->command);
- temp |= (CMD_EIE);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enable interrupts, cmd = 0x%x.", temp);
- writel(temp, &xhci->op_regs->command);
-
- temp = readl(&xhci->ir_set->irq_pending);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
- xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
- writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
-
if (xhci->quirks & XHCI_NEC_HOST) {
struct xhci_command *command;
The patch below does not apply to the 5.15-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From a808925075fb750804a60ff0710614466c396db4 Mon Sep 17 00:00:00 2001
From: Hongyu Xie <xy521521(a)gmail.com>
Date: Thu, 23 Jun 2022 14:19:42 +0300
Subject: [PATCH] xhci: Keep interrupt disabled in initialization until host is
running.
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable(a)kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 9ac56e9ffc64..cb99bed5f755 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -611,15 +611,37 @@ static int xhci_init(struct usb_hcd *hcd)
static int xhci_run_finished(struct xhci_hcd *xhci)
{
+ unsigned long flags;
+ u32 temp;
+
+ /*
+ * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+ * Protect the short window before host is running with a lock
+ */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+ temp = readl(&xhci->op_regs->command);
+ temp |= (CMD_EIE);
+ writel(temp, &xhci->op_regs->command);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+ temp = readl(&xhci->ir_set->irq_pending);
+ writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+
if (xhci_start(xhci)) {
xhci_halt(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
return -ENODEV;
}
+
xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
return 0;
}
@@ -668,19 +690,6 @@ int xhci_run(struct usb_hcd *hcd)
temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
writel(temp, &xhci->ir_set->irq_control);
- /* Set the HCD state before we enable the irqs */
- temp = readl(&xhci->op_regs->command);
- temp |= (CMD_EIE);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enable interrupts, cmd = 0x%x.", temp);
- writel(temp, &xhci->op_regs->command);
-
- temp = readl(&xhci->ir_set->irq_pending);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
- xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
- writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
-
if (xhci->quirks & XHCI_NEC_HOST) {
struct xhci_command *command;
The patch below does not apply to the 5.10-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From a808925075fb750804a60ff0710614466c396db4 Mon Sep 17 00:00:00 2001
From: Hongyu Xie <xy521521(a)gmail.com>
Date: Thu, 23 Jun 2022 14:19:42 +0300
Subject: [PATCH] xhci: Keep interrupt disabled in initialization until host is
running.
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable(a)kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 9ac56e9ffc64..cb99bed5f755 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -611,15 +611,37 @@ static int xhci_init(struct usb_hcd *hcd)
static int xhci_run_finished(struct xhci_hcd *xhci)
{
+ unsigned long flags;
+ u32 temp;
+
+ /*
+ * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+ * Protect the short window before host is running with a lock
+ */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+ temp = readl(&xhci->op_regs->command);
+ temp |= (CMD_EIE);
+ writel(temp, &xhci->op_regs->command);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+ temp = readl(&xhci->ir_set->irq_pending);
+ writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+
if (xhci_start(xhci)) {
xhci_halt(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
return -ENODEV;
}
+
xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
return 0;
}
@@ -668,19 +690,6 @@ int xhci_run(struct usb_hcd *hcd)
temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
writel(temp, &xhci->ir_set->irq_control);
- /* Set the HCD state before we enable the irqs */
- temp = readl(&xhci->op_regs->command);
- temp |= (CMD_EIE);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enable interrupts, cmd = 0x%x.", temp);
- writel(temp, &xhci->op_regs->command);
-
- temp = readl(&xhci->ir_set->irq_pending);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
- xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
- writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
-
if (xhci->quirks & XHCI_NEC_HOST) {
struct xhci_command *command;
The patch below does not apply to the 5.18-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From a808925075fb750804a60ff0710614466c396db4 Mon Sep 17 00:00:00 2001
From: Hongyu Xie <xy521521(a)gmail.com>
Date: Thu, 23 Jun 2022 14:19:42 +0300
Subject: [PATCH] xhci: Keep interrupt disabled in initialization until host is
running.
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable(a)kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 9ac56e9ffc64..cb99bed5f755 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -611,15 +611,37 @@ static int xhci_init(struct usb_hcd *hcd)
static int xhci_run_finished(struct xhci_hcd *xhci)
{
+ unsigned long flags;
+ u32 temp;
+
+ /*
+ * Enable interrupts before starting the host (xhci 4.2 and 5.5.2).
+ * Protect the short window before host is running with a lock
+ */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable interrupts");
+ temp = readl(&xhci->op_regs->command);
+ temp |= (CMD_EIE);
+ writel(temp, &xhci->op_regs->command);
+
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Enable primary interrupter");
+ temp = readl(&xhci->ir_set->irq_pending);
+ writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
+
if (xhci_start(xhci)) {
xhci_halt(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
return -ENODEV;
}
+
xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
return 0;
}
@@ -668,19 +690,6 @@ int xhci_run(struct usb_hcd *hcd)
temp |= (xhci->imod_interval / 250) & ER_IRQ_INTERVAL_MASK;
writel(temp, &xhci->ir_set->irq_control);
- /* Set the HCD state before we enable the irqs */
- temp = readl(&xhci->op_regs->command);
- temp |= (CMD_EIE);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enable interrupts, cmd = 0x%x.", temp);
- writel(temp, &xhci->op_regs->command);
-
- temp = readl(&xhci->ir_set->irq_pending);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init,
- "// Enabling event ring interrupter %p by writing 0x%x to irq_pending",
- xhci->ir_set, (unsigned int) ER_IRQ_ENABLE(temp));
- writel(ER_IRQ_ENABLE(temp), &xhci->ir_set->irq_pending);
-
if (xhci->quirks & XHCI_NEC_HOST) {
struct xhci_command *command;
The patch below does not apply to the 4.14-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 83810f84ecf11dfc5a9414a8b762c3501b328185 Mon Sep 17 00:00:00 2001
From: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Date: Thu, 23 Jun 2022 14:19:43 +0300
Subject: [PATCH] xhci: turn off port power in shutdown
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable(a)vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index c54f2bc23d3f..0fdc014c9401 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -652,7 +652,7 @@ struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd)
* It will release and re-aquire the lock while calling ACPI
* method.
*/
-static void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
u16 index, bool on, unsigned long *flags)
__must_hold(&xhci->lock)
{
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index cb99bed5f755..65858f607437 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -791,6 +791,8 @@ static void xhci_stop(struct usb_hcd *hcd)
void xhci_shutdown(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ unsigned long flags;
+ int i;
if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
usb_disable_xhci_ports(to_pci_dev(hcd->self.sysdev));
@@ -806,12 +808,21 @@ void xhci_shutdown(struct usb_hcd *hcd)
del_timer_sync(&xhci->shared_hcd->rh_timer);
}
- spin_lock_irq(&xhci->lock);
+ spin_lock_irqsave(&xhci->lock, flags);
xhci_halt(xhci);
+
+ /* Power off USB2 ports*/
+ for (i = 0; i < xhci->usb2_rhub.num_ports; i++)
+ xhci_set_port_power(xhci, xhci->main_hcd, i, false, &flags);
+
+ /* Power off USB3 ports*/
+ for (i = 0; i < xhci->usb3_rhub.num_ports; i++)
+ xhci_set_port_power(xhci, xhci->shared_hcd, i, false, &flags);
+
/* Workaround for spurious wakeups at shutdown with HSW */
if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
- spin_unlock_irq(&xhci->lock);
+ spin_unlock_irqrestore(&xhci->lock, flags);
xhci_cleanup_msix(xhci);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 0bd76c94a4b1..28aaf031f9a8 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -2196,6 +2196,8 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1);
struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd);
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd, u16 index,
+ bool on, unsigned long *flags);
void xhci_hc_died(struct xhci_hcd *xhci);
The patch below does not apply to the 4.9-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable(a)vger.kernel.org>.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 83810f84ecf11dfc5a9414a8b762c3501b328185 Mon Sep 17 00:00:00 2001
From: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Date: Thu, 23 Jun 2022 14:19:43 +0300
Subject: [PATCH] xhci: turn off port power in shutdown
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable(a)vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.inte…
Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org>
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index c54f2bc23d3f..0fdc014c9401 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -652,7 +652,7 @@ struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd)
* It will release and re-aquire the lock while calling ACPI
* method.
*/
-static void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
u16 index, bool on, unsigned long *flags)
__must_hold(&xhci->lock)
{
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index cb99bed5f755..65858f607437 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -791,6 +791,8 @@ static void xhci_stop(struct usb_hcd *hcd)
void xhci_shutdown(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ unsigned long flags;
+ int i;
if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
usb_disable_xhci_ports(to_pci_dev(hcd->self.sysdev));
@@ -806,12 +808,21 @@ void xhci_shutdown(struct usb_hcd *hcd)
del_timer_sync(&xhci->shared_hcd->rh_timer);
}
- spin_lock_irq(&xhci->lock);
+ spin_lock_irqsave(&xhci->lock, flags);
xhci_halt(xhci);
+
+ /* Power off USB2 ports*/
+ for (i = 0; i < xhci->usb2_rhub.num_ports; i++)
+ xhci_set_port_power(xhci, xhci->main_hcd, i, false, &flags);
+
+ /* Power off USB3 ports*/
+ for (i = 0; i < xhci->usb3_rhub.num_ports; i++)
+ xhci_set_port_power(xhci, xhci->shared_hcd, i, false, &flags);
+
/* Workaround for spurious wakeups at shutdown with HSW */
if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
- spin_unlock_irq(&xhci->lock);
+ spin_unlock_irqrestore(&xhci->lock, flags);
xhci_cleanup_msix(xhci);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 0bd76c94a4b1..28aaf031f9a8 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -2196,6 +2196,8 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1);
struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd);
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd, u16 index,
+ bool on, unsigned long *flags);
void xhci_hc_died(struct xhci_hcd *xhci);