[ 0.000000] Linux version 6.8.0-1-mainline-08073-g480e035fc4c7 (linux-mainline@archlinux) (gcc (GCC) 14.1.1 20240522, GNU ld (GNU Binutils) 2.42.0) #1 SMP PREEMPT_DYNAMIC Thu, 23 May 2024 21:57:23 +0000 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux-mainline root=UUID=963daeed-0888-4658-9f17-18bd343dfb2a rw zswap.enabled=0 rootfstype=ext4 loglevel=3 quiet [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bfdeffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bfdf0000-0x00000000bfdf2fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bfdf3000-0x00000000bfdfffff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bfe00000-0x00000000bfefffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: Gigabyte Technology Co., Ltd. GA-78LMT-USB3 R2/GA-78LMT-USB3 R2, BIOS F1 11/08/2017 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 3321.914 MHz processor [ 0.002877] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.002881] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.002886] last_pfn = 0x43f000 max_arch_pfn = 0x400000000 [ 0.002895] total RAM covered: 3070M [ 0.003161] Found optimal setting for mtrr clean up [ 0.003162] gran_size: 64K chunk_size: 4M num_reg: 3 lose cover RAM: 0G [ 0.003168] MTRR map: 7 entries (4 fixed + 3 variable; max 21), built from 9 variable MTRRs [ 0.003170] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.004028] e820: update [mem 0xbfe00000-0xffffffff] usable ==> reserved [ 0.004038] last_pfn = 0xbfdf0 max_arch_pfn = 0x400000000 [ 0.006834] found SMP MP-table at [mem 0x000f5ea0-0x000f5eaf] [ 0.006854] Using GB pages for direct mapping [ 0.007124] RAMDISK: [mem 0x31caf000-0x34e4efff] [ 0.007248] ACPI: Early table checksum verification disabled [ 0.007253] ACPI: RSDP 0x00000000000F78B0 000014 (v00 GBT ) [ 0.007257] ACPI: RSDT 0x00000000BFDF3000 000040 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007263] ACPI: FACP 0x00000000BFDF3080 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007269] ACPI: DSDT 0x00000000BFDF3100 0069E7 (v01 GBT GBTUACPI 00001000 MSFT 03000000) [ 0.007274] ACPI: FACS 0x00000000BFDF0000 000040 [ 0.007277] ACPI: MSDM 0x00000000BFDF9BC0 000055 (v03 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007281] ACPI: HPET 0x00000000BFDF9C40 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098) [ 0.007284] ACPI: MCFG 0x00000000BFDF9C80 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007288] ACPI: TAMG 0x00000000BFDF9CC0 000022 (v01 GBT GBT B0 5455312E BG?? 00000101) [ 0.007291] ACPI: APIC 0x00000000BFDF9B00 0000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007295] ACPI: SSDT 0x00000000BFDF9D60 001714 (v01 AMD POWERNOW 00000001 AMD 00000001) [ 0.007298] ACPI: Reserving FACP table memory at [mem 0xbfdf3080-0xbfdf30f3] [ 0.007299] ACPI: Reserving DSDT table memory at [mem 0xbfdf3100-0xbfdf9ae6] [ 0.007301] ACPI: Reserving FACS table memory at [mem 0xbfdf0000-0xbfdf003f] [ 0.007302] ACPI: Reserving MSDM table memory at [mem 0xbfdf9bc0-0xbfdf9c14] [ 0.007303] ACPI: Reserving HPET table memory at [mem 0xbfdf9c40-0xbfdf9c77] [ 0.007304] ACPI: Reserving MCFG table memory at [mem 0xbfdf9c80-0xbfdf9cbb] [ 0.007305] ACPI: Reserving TAMG table memory at [mem 0xbfdf9cc0-0xbfdf9ce1] [ 0.007306] ACPI: Reserving APIC table memory at [mem 0xbfdf9b00-0xbfdf9bbb] [ 0.007307] ACPI: Reserving SSDT table memory at [mem 0xbfdf9d60-0xbfdfb473] [ 0.007372] No NUMA configuration found [ 0.007373] Faking a node at [mem 0x0000000000000000-0x000000043effffff] [ 0.007376] NODE_DATA(0) allocated [mem 0x43effb000-0x43effffff] [ 0.007408] Zone ranges: [ 0.007409] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.007411] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.007413] Normal [mem 0x0000000100000000-0x000000043effffff] [ 0.007415] Device empty [ 0.007416] Movable zone start for each node [ 0.007417] Early memory node ranges [ 0.007418] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.007420] node 0: [mem 0x0000000000100000-0x00000000bfdeffff] [ 0.007421] node 0: [mem 0x0000000100000000-0x000000043effffff] [ 0.007424] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff] [ 0.007430] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.007466] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.054798] On node 0, zone Normal: 528 pages in unavailable ranges [ 0.054868] On node 0, zone Normal: 4096 pages in unavailable ranges [ 0.055052] ACPI: PM-Timer IO Port: 0x4008 [ 0.055064] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.055066] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.055067] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.055068] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) [ 0.055069] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1]) [ 0.055070] ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1]) [ 0.055072] ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1]) [ 0.055073] ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1]) [ 0.055086] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.055089] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.055091] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.055096] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.055097] ACPI: HPET id: 0x10b9a201 base: 0xfed00000 [ 0.055107] CPU topo: Max. logical packages: 1 [ 0.055108] CPU topo: Max. logical dies: 1 [ 0.055109] CPU topo: Max. dies per package: 1 [ 0.055115] CPU topo: Max. threads per core: 2 [ 0.055116] CPU topo: Num. cores per package: 4 [ 0.055117] CPU topo: Num. threads per package: 8 [ 0.055118] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs [ 0.055130] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.055132] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.055133] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.055134] PM: hibernation: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.055136] PM: hibernation: Registered nosave memory: [mem 0xbfdf0000-0xbfdf2fff] [ 0.055137] PM: hibernation: Registered nosave memory: [mem 0xbfdf3000-0xbfdfffff] [ 0.055138] PM: hibernation: Registered nosave memory: [mem 0xbfe00000-0xbfefffff] [ 0.055139] PM: hibernation: Registered nosave memory: [mem 0xbff00000-0xdfffffff] [ 0.055140] PM: hibernation: Registered nosave memory: [mem 0xe0000000-0xefffffff] [ 0.055141] PM: hibernation: Registered nosave memory: [mem 0xf0000000-0xfebfffff] [ 0.055142] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xffffffff] [ 0.055144] [mem 0xbff00000-0xdfffffff] available for PCI devices [ 0.055146] Booting paravirtualized kernel on bare hardware [ 0.055149] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns [ 0.060898] setup_percpu: NR_CPUS:320 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1 [ 0.061917] percpu: Embedded 66 pages/cpu s233472 r8192 d28672 u524288 [ 0.061923] pcpu-alloc: s233472 r8192 d28672 u524288 alloc=1*2097152 [ 0.061926] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 [ 0.061947] Kernel command line: BOOT_IMAGE=/vmlinuz-linux-mainline root=UUID=963daeed-0888-4658-9f17-18bd343dfb2a rw zswap.enabled=0 rootfstype=ext4 loglevel=3 quiet [ 0.062035] Unknown kernel command line parameters "BOOT_IMAGE=/vmlinuz-linux-mainline", will be passed to user space. [ 0.064853] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.066267] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.066346] Fallback order for Node 0: 0 [ 0.066352] Built 1 zonelists, mobility grouping on. Total pages: 4123960 [ 0.066353] Policy zone: Normal [ 0.066760] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.066766] software IO TLB: area num 8. [ 0.153391] Memory: 16303888K/16758328K available (16384K kernel code, 2138K rwdata, 13024K rodata, 3468K init, 3716K bss, 454180K reserved, 0K cma-reserved) [ 0.161590] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.161761] ftrace: allocating 49117 entries in 192 pages [ 0.172827] ftrace: allocated 192 pages with 2 groups [ 0.172994] Dynamic Preempt: full [ 0.173222] rcu: Preemptible hierarchical RCU implementation. [ 0.173223] rcu: RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=8. [ 0.173225] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.173226] Trampoline variant of Tasks RCU enabled. [ 0.173227] Rude variant of Tasks RCU enabled. [ 0.173227] Tracing variant of Tasks RCU enabled. [ 0.173228] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.173229] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.173237] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.173239] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.173241] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.177113] NR_IRQS: 20736, nr_irqs: 488, preallocated irqs: 16 [ 0.177313] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.177401] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____) [ 0.177476] spurious 8259A interrupt: IRQ7. [ 0.177494] Console: colour dummy device 80x25 [ 0.177497] printk: legacy console [tty0] enabled [ 0.177895] ACPI: Core revision 20230628 [ 0.178130] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns [ 0.178163] APIC: Switch to symmetric I/O mode setup [ 0.178665] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.194818] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2fe22977dcd, max_idle_ns: 440795267503 ns [ 0.194823] Calibrating delay loop (skipped), value calculated using timer frequency.. 6646.65 BogoMIPS (lpj=11073046) [ 0.194847] LVT offset 1 assigned for vector 0xf9 [ 0.194852] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.194853] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.194858] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.194861] Spectre V2 : Mitigation: Retpolines [ 0.194862] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.194863] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.194864] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.194865] RETBleed: Mitigation: untrained return thunk [ 0.194867] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.194869] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.194873] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.194875] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.194876] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.194878] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.194879] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.218347] Freeing SMP alternatives memory: 40K [ 0.218352] pid_max: default: 32768 minimum: 301 [ 0.219081] LSM: initializing lsm=capability,landlock,lockdown,yama,bpf [ 0.219939] landlock: Up and running. [ 0.219940] Yama: becoming mindful. [ 0.219947] LSM support for eBPF active [ 0.220195] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.220235] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.228216] APIC calibration not consistent with PM-Timer: 0ms instead of 100ms [ 0.228222] APIC delta adjusted to PM-Timer: 1258139 (1543) [ 0.228231] smpboot: CPU0: AMD FX(tm)-8300 Eight-Core Processor (family: 0x15, model: 0x2, stepping: 0x0) [ 0.228577] Performance Events: Fam15h core perfctr, AMD PMU driver. [ 0.228583] ... version: 0 [ 0.228584] ... bit width: 48 [ 0.228585] ... generic registers: 6 [ 0.228586] ... value mask: 0000ffffffffffff [ 0.228587] ... max period: 00007fffffffffff [ 0.228588] ... fixed-purpose events: 0 [ 0.228589] ... event mask: 000000000000003f [ 0.228679] signal: max sigframe size: 1776 [ 0.228728] rcu: Hierarchical SRCU implementation. [ 0.228729] rcu: Max phase no-delay instances is 1000. [ 0.231158] MCE: In-kernel MCE decoding enabled. [ 0.231233] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. [ 0.231354] smp: Bringing up secondary CPUs ... [ 0.231487] smpboot: x86: Booting SMP configuration: [ 0.231487] .... node #0, CPUs: #2 #4 #6 [ 0.000816] __common_interrupt: 2.55 No irq handler for vector [ 0.000816] __common_interrupt: 4.55 No irq handler for vector [ 0.000816] __common_interrupt: 6.55 No irq handler for vector [ 0.245808] #1 #3 #5 #7 [ 0.000816] ------------[ cut here ]------------ [ 0.000816] WARNING: CPU: 1 PID: 0 at kernel/sched/core.c:6482 sched_cpu_starting+0x183/0x250 [ 0.000816] Modules linked in: [ 0.000816] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0-1-mainline-08073-g480e035fc4c7 #1 b5b4939a7e36e7c9543996b79d4ad983e0adb635 [ 0.000816] Hardware name: Gigabyte Technology Co., Ltd. GA-78LMT-USB3 R2/GA-78LMT-USB3 R2, BIOS F1 11/08/2017 [ 0.000816] RIP: 0010:sched_cpu_starting+0x183/0x250 [ 0.000816] Code: 00 8b 0d c0 26 f0 01 39 c8 0f 83 71 ff ff ff 48 63 d0 48 8b 3c d5 40 62 6e ba 4c 01 e7 39 c3 75 c7 4c 89 bf 48 0d 00 00 eb c7 <0f> 0b eb c3 be 04 00 00 00 89 df e8 4d 5f 02 00 84 c0 0f 85 71 ff [ 0.000816] RSP: 0000:ffffb040800cfe40 EFLAGS: 00010087 [ 0.000816] RAX: 0000000000000002 RBX: 0000000000000001 RCX: 0000000000000008 [ 0.000816] RDX: 0000000000000002 RSI: fffffffffffffffc RDI: ffff8f31eeb36180 [ 0.000816] RBP: ffff8f31eea99b00 R08: ffff8f31eea99b00 R09: 0000000000000000 [ 0.000816] R10: ffff8f31eea99b00 R11: 0000000000000006 R12: 0000000000036180 [ 0.000816] R13: 0000000000036180 R14: 0000000000000001 R15: ffff8f31eea36180 [ 0.000816] FS: 0000000000000000(0000) GS:ffff8f31eea80000(0000) knlGS:0000000000000000 [ 0.000816] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 0.000816] CR2: 0000000000000000 CR3: 00000003d0820000 CR4: 00000000000406f0 [ 0.000816] Call Trace: [ 0.000816] [ 0.000816] ? __warn+0x80/0x120 [ 0.000816] ? sched_cpu_starting+0x183/0x250 [ 0.000816] ? report_bug+0x15e/0x190 [ 0.000816] ? handle_bug+0x3c/0x80 [ 0.000816] ? exc_invalid_op+0x17/0x70 [ 0.000816] ? asm_exc_invalid_op+0x1a/0x20 [ 0.000816] ? sched_cpu_starting+0x183/0x250 [ 0.000816] ? __pfx_sched_cpu_starting+0x10/0x10 [ 0.000816] cpuhp_invoke_callback+0x122/0x410 [ 0.000816] ? mcheck_cpu_init+0x1ef/0x4b0 [ 0.000816] __cpuhp_invoke_callback_range+0x84/0x100 [ 0.000816] start_secondary+0x9c/0x140 [ 0.000816] common_startup_64+0x13e/0x141 [ 0.000816] [ 0.000816] ---[ end trace 0000000000000000 ]--- [ 0.000816] __common_interrupt: 1.55 No irq handler for vector [ 0.000816] __common_interrupt: 3.55 No irq handler for vector [ 0.000816] __common_interrupt: 5.55 No irq handler for vector [ 0.000816] __common_interrupt: 7.55 No irq handler for vector [ 0.262496] smp: Brought up 1 node, 8 CPUs [ 0.262496] smpboot: Total of 8 processors activated (53171.23 BogoMIPS) [ 0.264907] ------------[ cut here ]------------ [ 0.264911] WARNING: CPU: 0 PID: 1 at kernel/sched/topology.c:2408 build_sched_domains+0x7b0/0x1300 [ 0.264918] Modules linked in: [ 0.264921] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.8.0-1-mainline-08073-g480e035fc4c7 #1 b5b4939a7e36e7c9543996b79d4ad983e0adb635 [ 0.264926] Hardware name: Gigabyte Technology Co., Ltd. GA-78LMT-USB3 R2/GA-78LMT-USB3 R2, BIOS F1 11/08/2017 [ 0.264927] RIP: 0010:build_sched_domains+0x7b0/0x1300 [ 0.264932] Code: 56 5b 01 00 4c 89 ea 4c 89 e6 4c 89 e7 8b 0d f7 e6 ec 01 e8 42 a3 52 00 e9 72 fe ff ff 41 c7 46 30 01 00 00 00 e9 0e fe ff ff <0f> 0b 41 be f4 ff ff ff 48 8b 5c 24 68 8b 03 85 c0 0f 84 f1 01 00 [ 0.264934] RSP: 0018:ffffb0408001fe20 EFLAGS: 00010202 [ 0.264936] RAX: 00000000ffffff01 RBX: 0000000000000000 RCX: 00000000ffffff01 [ 0.264938] RDX: 00000000fffffff8 RSI: 0000000000000003 RDI: ffff8f31eea19b00 [ 0.264939] RBP: ffff8f2ec0359200 R08: ffff8f31eea19b00 R09: 0000000000000000 [ 0.264941] R10: ffffb0408001fde8 R11: 0000000000000000 R12: 0000000000000001 [ 0.264942] R13: ffff8f31eea99b00 R14: 0000000000000001 R15: ffff8f2ec08b3b40 [ 0.264944] FS: 0000000000000000(0000) GS:ffff8f31eea00000(0000) knlGS:0000000000000000 [ 0.264946] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 0.264947] CR2: ffff8f3191601000 CR3: 00000003d0820000 CR4: 00000000000406f0 [ 0.264949] Call Trace: [ 0.264952] [ 0.264954] ? __warn+0x80/0x120 [ 0.264958] ? build_sched_domains+0x7b0/0x1300 [ 0.264962] ? report_bug+0x15e/0x190 [ 0.264966] ? handle_bug+0x3c/0x80 [ 0.264969] ? exc_invalid_op+0x17/0x70 [ 0.264971] ? asm_exc_invalid_op+0x1a/0x20 [ 0.264974] ? build_sched_domains+0x7b0/0x1300 [ 0.264978] ? kmalloc_trace+0x13a/0x320 [ 0.264982] sched_init_smp+0x3e/0xc0 [ 0.264986] ? stop_machine+0x30/0x40 [ 0.264988] kernel_init_freeable+0xf8/0x320 [ 0.264991] ? __pfx_kernel_init+0x10/0x10 [ 0.264994] kernel_init+0x1a/0x1c0 [ 0.264997] ret_from_fork+0x34/0x50 [ 0.265000] ? __pfx_kernel_init+0x10/0x10 [ 0.265003] ret_from_fork_asm+0x1a/0x30 [ 0.265007] [ 0.265008] ---[ end trace 0000000000000000 ]--- [ 0.265933] devtmpfs: initialized [ 0.265969] x86/mm: Memory block size: 128MB [ 0.269416] ACPI: PM: Registering ACPI NVS region [mem 0xbfdf0000-0xbfdf2fff] (12288 bytes) [ 0.269477] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.269499] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.270045] pinctrl core: initialized pinctrl subsystem [ 0.270179] PM: RTC time: 13:40:51, date: 2024-05-24 [ 0.271179] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.271607] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.271872] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.272159] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.272180] audit: initializing netlink subsys (disabled) [ 0.272233] audit: type=2000 audit(1716558050.096:1): state=initialized audit_enabled=0 res=1 [ 0.272369] thermal_sys: Registered thermal governor 'fair_share' [ 0.272371] thermal_sys: Registered thermal governor 'bang_bang' [ 0.272372] thermal_sys: Registered thermal governor 'step_wise' [ 0.272373] thermal_sys: Registered thermal governor 'user_space' [ 0.272374] thermal_sys: Registered thermal governor 'power_allocator' [ 0.272387] cpuidle: using governor ladder [ 0.272392] cpuidle: using governor menu [ 0.272421] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.272421] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.272421] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.272421] PCI: Using configuration type 1 for base access [ 0.272421] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.278331] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.278333] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page [ 0.278335] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.278336] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page [ 0.288266] fbcon: Taking over console [ 0.288287] ACPI: Added _OSI(Module Device) [ 0.288288] ACPI: Added _OSI(Processor Device) [ 0.288289] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.288291] ACPI: Added _OSI(Processor Aggregator Device) [ 0.297587] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.297853] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.297860] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297866] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.297872] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.297883] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297889] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.297894] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.297899] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.297911] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.297916] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.297921] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.297926] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297938] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.297943] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.297948] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297953] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.297964] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.297970] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297975] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.297980] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.297991] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.297997] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.298002] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.298007] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.298018] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.298024] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.298029] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.298034] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.298045] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.298051] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.298056] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.298061] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.298072] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.298077] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.298083] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.298088] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.298099] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.298104] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.298109] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.298114] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.308221] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.308461] ACPI: Interpreter enabled [ 0.308483] ACPI: PM: (supports S0 S3 S4 S5) [ 0.308485] ACPI: Using IOAPIC for interrupt routing [ 0.308826] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.308828] PCI: Using E820 reservations for host bridge windows [ 0.308980] ACPI: Enabled 5 GPEs in block 00 to 1F [ 0.321558] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.321566] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3] [ 0.321937] PCI host bridge to bus 0000:00 [ 0.321939] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.321942] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.321945] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window] [ 0.321948] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.321950] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.321968] pci 0000:00:00.0: [1022:9600] type 00 class 0x060000 conventional PCI endpoint [ 0.321980] pci 0000:00:00.0: [Firmware Bug]: BAR 3: invalid; can't size [ 0.322056] pci 0000:00:02.0: [1022:9603] type 01 class 0x060400 PCIe Root Port [ 0.322069] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.322073] pci 0000:00:02.0: bridge window [io 0xe000-0xefff] [ 0.322076] pci 0000:00:02.0: bridge window [mem 0xfb000000-0xfcffffff] [ 0.322081] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.322088] pci 0000:00:02.0: enabling Extended Tags [ 0.322115] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold [ 0.322220] pci 0000:00:04.0: [1022:9604] type 01 class 0x060400 PCIe Root Port [ 0.322233] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.322236] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff] [ 0.322239] pci 0000:00:04.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.322244] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.322250] pci 0000:00:04.0: enabling Extended Tags [ 0.322275] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.322372] pci 0000:00:06.0: [1022:9606] type 01 class 0x060400 PCIe Root Port [ 0.322384] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.322388] pci 0000:00:06.0: bridge window [io 0xc000-0xcfff] [ 0.322391] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff] [ 0.322395] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.322401] pci 0000:00:06.0: enabling Extended Tags [ 0.322426] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold [ 0.322543] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.322560] pci 0000:00:11.0: BAR 0 [io 0xff00-0xff07] [ 0.322569] pci 0000:00:11.0: BAR 1 [io 0xfe00-0xfe03] [ 0.322578] pci 0000:00:11.0: BAR 2 [io 0xfd00-0xfd07] [ 0.322587] pci 0000:00:11.0: BAR 3 [io 0xfc00-0xfc03] [ 0.322596] pci 0000:00:11.0: BAR 4 [io 0xfb00-0xfb0f] [ 0.322605] pci 0000:00:11.0: BAR 5 [mem 0xfe02f000-0xfe02f3ff] [ 0.322627] pci 0000:00:11.0: set SATA to AHCI mode [ 0.322732] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.322749] pci 0000:00:12.0: BAR 0 [mem 0xfe02e000-0xfe02efff] [ 0.322885] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.322901] pci 0000:00:12.1: BAR 0 [mem 0xfe02d000-0xfe02dfff] [ 0.323039] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.323056] pci 0000:00:12.2: BAR 0 [mem 0xfe02c000-0xfe02c0ff] [ 0.323134] pci 0000:00:12.2: supports D1 D2 [ 0.323136] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.323222] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.323239] pci 0000:00:13.0: BAR 0 [mem 0xfe02b000-0xfe02bfff] [ 0.323364] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.323384] pci 0000:00:13.1: BAR 0 [mem 0xfe02a000-0xfe02afff] [ 0.323517] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.323534] pci 0000:00:13.2: BAR 0 [mem 0xfe029000-0xfe0290ff] [ 0.323611] pci 0000:00:13.2: supports D1 D2 [ 0.323613] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.323705] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.323855] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.323872] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.323881] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.323890] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.323899] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.323907] pci 0000:00:14.1: BAR 4 [io 0xfa00-0xfa0f] [ 0.323927] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.323929] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.323930] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.323932] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.324037] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300 conventional PCI endpoint [ 0.324058] pci 0000:00:14.2: BAR 0 [mem 0xfe024000-0xfe027fff 64bit] [ 0.324123] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.324202] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.324370] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.324401] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode) [ 0.324406] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.324410] pci 0000:00:14.4: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.324415] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff pref] [ 0.324498] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.324514] pci 0000:00:14.5: BAR 0 [mem 0xfe028000-0xfe028fff] [ 0.324643] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.324696] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.324741] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.324786] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.324852] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.324898] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.324993] pci 0000:01:00.0: [10de:1c82] type 00 class 0x030000 PCIe Legacy Endpoint [ 0.325006] pci 0000:01:00.0: BAR 0 [mem 0xfb000000-0xfbffffff] [ 0.325017] pci 0000:01:00.0: BAR 1 [mem 0xc0000000-0xcfffffff 64bit pref] [ 0.325027] pci 0000:01:00.0: BAR 3 [mem 0xde000000-0xdfffffff 64bit pref] [ 0.325035] pci 0000:01:00.0: BAR 5 [io 0xef00-0xef7f] [ 0.325042] pci 0000:01:00.0: ROM [mem 0x00000000-0x0007ffff pref] [ 0.325065] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.325149] pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x16 link at 0000:00:02.0 (capable of 126.016 Gb/s with 8.0 GT/s PCIe x16 link) [ 0.325224] pci 0000:01:00.1: [10de:0fb9] type 00 class 0x040300 PCIe Endpoint [ 0.325237] pci 0000:01:00.1: BAR 0 [mem 0xfcffc000-0xfcffffff] [ 0.325384] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.325426] pci 0000:02:00.0: [1106:3483] type 00 class 0x0c0330 PCIe Endpoint [ 0.325441] pci 0000:02:00.0: BAR 0 [mem 0xfdaff000-0xfdafffff 64bit] [ 0.325500] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.325570] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.325614] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint [ 0.325630] pci 0000:03:00.0: BAR 0 [io 0xce00-0xceff] [ 0.325650] pci 0000:03:00.0: BAR 2 [mem 0xfdeff000-0xfdefffff 64bit] [ 0.325663] pci 0000:03:00.0: BAR 4 [mem 0xfddfc000-0xfddfffff 64bit pref] [ 0.325741] pci 0000:03:00.0: supports D1 D2 [ 0.325743] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.325868] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.325883] pci_bus 0000:04: extended config space not accessible [ 0.325944] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode) [ 0.325953] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.325955] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.325957] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000dffff window] (subtractive decode) [ 0.325959] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xfebfffff window] (subtractive decode) [ 0.326238] ACPI: PCI: Interrupt link LNKA configured for IRQ 0 [ 0.326240] ACPI: PCI: Interrupt link LNKA disabled [ 0.326295] ACPI: PCI: Interrupt link LNKB configured for IRQ 0 [ 0.326296] ACPI: PCI: Interrupt link LNKB disabled [ 0.326350] ACPI: PCI: Interrupt link LNKC configured for IRQ 0 [ 0.326352] ACPI: PCI: Interrupt link LNKC disabled [ 0.326405] ACPI: PCI: Interrupt link LNKD configured for IRQ 0 [ 0.326407] ACPI: PCI: Interrupt link LNKD disabled [ 0.326460] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.326462] ACPI: PCI: Interrupt link LNKE disabled [ 0.326515] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.326516] ACPI: PCI: Interrupt link LNKF disabled [ 0.326569] ACPI: PCI: Interrupt link LNK0 configured for IRQ 0 [ 0.326571] ACPI: PCI: Interrupt link LNK0 disabled [ 0.326624] ACPI: PCI: Interrupt link LNK1 configured for IRQ 0 [ 0.326625] ACPI: PCI: Interrupt link LNK1 disabled [ 0.327453] iommu: Default domain type: Translated [ 0.327455] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.327719] SCSI subsystem initialized [ 0.327759] libata version 3.00 loaded. [ 0.327765] ACPI: bus type USB registered [ 0.327780] usbcore: registered new interface driver usbfs [ 0.327786] usbcore: registered new interface driver hub [ 0.327797] usbcore: registered new device driver usb [ 0.327828] EDAC MC: Ver: 3.0.0 [ 0.328218] NetLabel: Initializing [ 0.328220] NetLabel: domain hash size = 128 [ 0.328221] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.328238] NetLabel: unlabeled traffic allowed by default [ 0.328242] mctp: management component transport protocol core [ 0.328244] NET: Registered PF_MCTP protocol family [ 0.328251] PCI: Using ACPI for IRQ routing [ 0.336650] PCI: pci_cache_line_size set to 64 bytes [ 0.336704] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff] [ 0.336723] e820: reserve RAM buffer [mem 0xbfdf0000-0xbfffffff] [ 0.336724] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff] [ 0.336768] pci 0000:01:00.0: vgaarb: setting as boot VGA device [ 0.336770] pci 0000:01:00.0: vgaarb: bridge control possible [ 0.336771] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.336774] vgaarb: loaded [ 0.336857] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.336863] hpet0: 4 comparators, 32-bit 14.318180 MHz counter [ 0.338281] clocksource: Switched to clocksource tsc-early [ 0.339740] VFS: Disk quotas dquot_6.6.0 [ 0.339801] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.339900] pnp: PnP ACPI init [ 0.339988] system 00:00: [io 0x04d0-0x04d1] has been reserved [ 0.339992] system 00:00: [io 0x0220-0x0225] has been reserved [ 0.339994] system 00:00: [io 0x0290-0x0294] has been reserved [ 0.340295] system 00:01: [io 0x4100-0x411f] has been reserved [ 0.340299] system 00:01: [io 0x0228-0x022f] has been reserved [ 0.340301] system 00:01: [io 0x040b] has been reserved [ 0.340303] system 00:01: [io 0x04d6] has been reserved [ 0.340305] system 00:01: [io 0x0c00-0x0c01] has been reserved [ 0.340307] system 00:01: [io 0x0c14] has been reserved [ 0.340309] system 00:01: [io 0x0c50-0x0c52] has been reserved [ 0.340311] system 00:01: [io 0x0c6c-0x0c6d] has been reserved [ 0.340313] system 00:01: [io 0x0c6f] has been reserved [ 0.340314] system 00:01: [io 0x0cd0-0x0cd1] has been reserved [ 0.340316] system 00:01: [io 0x0cd2-0x0cd3] has been reserved [ 0.340318] system 00:01: [io 0x0cd4-0x0cdf] has been reserved [ 0.340320] system 00:01: [io 0x4000-0x40fe] has been reserved [ 0.340322] system 00:01: [io 0x4210-0x4217] has been reserved [ 0.340324] system 00:01: [io 0x0b00-0x0b0f] has been reserved [ 0.340325] system 00:01: [io 0x0b10-0x0b1f] has been reserved [ 0.340327] system 00:01: [io 0x0b20-0x0b3f] has been reserved [ 0.340329] system 00:01: [mem 0x00000000-0x00000fff window] could not be reserved [ 0.340332] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved [ 0.341258] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved [ 0.341482] pnp 00:06: disabling [mem 0x000ce600-0x000cffff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.341504] system 00:06: [mem 0x000f0000-0x000f7fff] could not be reserved [ 0.341507] system 00:06: [mem 0x000f8000-0x000fbfff] could not be reserved [ 0.341509] system 00:06: [mem 0x000fc000-0x000fffff] could not be reserved [ 0.341511] system 00:06: [mem 0xbfdf0000-0xbfdfffff] could not be reserved [ 0.341514] system 00:06: [mem 0xffff0000-0xffffffff] has been reserved [ 0.341516] system 00:06: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.341518] system 00:06: [mem 0x00100000-0xbfdeffff] could not be reserved [ 0.341520] system 00:06: [mem 0xbfe00000-0xbfefffff] has been reserved [ 0.341522] system 00:06: [mem 0xbff00000-0xbfffffff] could not be reserved [ 0.341524] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.341526] system 00:06: [mem 0xfee00000-0xfee00fff] could not be reserved [ 0.341528] system 00:06: [mem 0xfff80000-0xfffeffff] has been reserved [ 0.341551] pnp: PnP ACPI: found 7 devices [ 0.347675] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.347949] NET: Registered PF_INET protocol family [ 0.348240] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.365489] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.365532] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.365691] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.366117] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.366431] TCP: Hash tables configured (established 131072 bind 65536) [ 0.366657] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear) [ 0.366758] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.366824] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.366928] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.366943] NET: Registered PF_XDP protocol family [ 0.366958] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.366962] pci 0000:00:02.0: bridge window [io 0xe000-0xefff] [ 0.366966] pci 0000:00:02.0: bridge window [mem 0xfb000000-0xfcffffff] [ 0.366969] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.366973] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.366975] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff] [ 0.366978] pci 0000:00:04.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.366980] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.366984] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.366986] pci 0000:00:06.0: bridge window [io 0xc000-0xcfff] [ 0.366989] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff] [ 0.366991] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.366995] pci 0000:00:14.4: PCI bridge to [bus 04] [ 0.366998] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.367003] pci 0000:00:14.4: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.367006] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff pref] [ 0.367014] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.367016] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.367018] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window] [ 0.367020] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.367022] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.367023] pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff] [ 0.367025] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.367027] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.367029] pci_bus 0000:02: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.367031] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.367033] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] [ 0.367034] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff] [ 0.367036] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.367038] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.367039] pci_bus 0000:04: resource 1 [mem 0xfdc00000-0xfdcfffff] [ 0.367041] pci_bus 0000:04: resource 2 [mem 0xfdb00000-0xfdbfffff pref] [ 0.367043] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7 window] [ 0.367045] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff window] [ 0.367046] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000dffff window] [ 0.367048] pci_bus 0000:04: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.384132] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7b0 took 16620 usecs [ 0.400803] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7b0 took 16262 usecs [ 0.420792] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7b0 took 19302 usecs [ 0.437489] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7b0 took 16288 usecs [ 0.457452] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7b0 took 19263 usecs [ 0.457488] pci 0000:01:00.1: extending delay after power-on from D3hot to 20 msec [ 0.457526] pci 0000:01:00.1: D0 power state depends on 0000:01:00.0 [ 0.457731] PCI: CLS 64 bytes, default 64 [ 0.457791] Trying to unpack rootfs image as initramfs... [ 0.460644] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.460648] software IO TLB: mapped [mem 0x00000000bbdf0000-0x00000000bfdf0000] (64MB) [ 0.460698] LVT offset 0 assigned for vector 0x400 [ 0.460831] perf: AMD IBS detected (0x000000ff) [ 0.462452] Initialise system trusted keyrings [ 0.462476] Key type blacklist registered [ 0.462535] workingset: timestamp_bits=41 max_order=22 bucket_order=0 [ 0.462542] zbud: loaded [ 0.464233] integrity: Platform Keyring initialized [ 0.464244] integrity: Machine keyring initialized [ 0.491817] Key type asymmetric registered [ 0.491822] Asymmetric key parser 'x509' registered [ 0.491904] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.493996] io scheduler mq-deadline registered [ 0.493999] io scheduler kyber registered [ 0.494051] io scheduler bfq registered [ 0.495020] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 0.495120] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 0.495147] ACPI: button: Power Button [PWRB] [ 0.495187] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.503997] ACPI: button: Power Button [PWRF] [ 0.504047] ACPI: \_PR_.C000: Found 2 idle states [ 0.504123] ACPI: \_PR_.C001: Found 2 idle states [ 0.504195] ACPI: \_PR_.C002: Found 2 idle states [ 0.504263] ACPI: \_PR_.C003: Found 2 idle states [ 0.504333] ACPI: \_PR_.C004: Found 2 idle states [ 0.504404] ACPI: \_PR_.C005: Found 2 idle states [ 0.504473] ACPI: \_PR_.C006: Found 2 idle states [ 0.504536] ACPI: \_PR_.C007: Found 2 idle states [ 0.504807] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.504980] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 0.512096] Non-volatile memory driver v1.3 [ 0.512099] Linux agpgart interface v0.103 [ 0.512221] ACPI: bus type drm_connector registered [ 0.513072] ahci 0000:00:11.0: version 3.0 [ 0.513290] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 0.513294] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 0.513296] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 0.513777] scsi host0: ahci [ 0.513930] scsi host1: ahci [ 0.514042] scsi host2: ahci [ 0.514132] scsi host3: ahci [ 0.514175] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 lpm-pol 3 [ 0.514178] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 lpm-pol 3 [ 0.514180] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 lpm-pol 3 [ 0.514182] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 lpm-pol 3 [ 0.514382] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 0.514388] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 0.514419] ohci-pci 0000:00:12.0: irq 16, io mem 0xfe02e000 [ 0.577359] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.08 [ 0.577366] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.577368] usb usb1: Product: OHCI PCI host controller [ 0.577370] usb usb1: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ohci_hcd [ 0.577372] usb usb1: SerialNumber: 0000:00:12.0 [ 0.577515] hub 1-0:1.0: USB hub found [ 0.577524] hub 1-0:1.0: 3 ports detected [ 0.577751] ehci-pci 0000:00:12.2: EHCI Host Controller [ 0.577756] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 0.577760] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 0.577770] ehci-pci 0000:00:12.2: debug port 1 [ 0.577823] ehci-pci 0000:00:12.2: irq 17, io mem 0xfe02c000 [ 0.582498] Freeing initrd memory: 50816K [ 0.590678] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 0.590829] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.08 [ 0.590838] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.590843] usb usb2: Product: EHCI Host Controller [ 0.590847] usb usb2: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ehci_hcd [ 0.590851] usb usb2: SerialNumber: 0000:00:12.2 [ 0.591006] hub 2-0:1.0: USB hub found [ 0.591020] hub 2-0:1.0: 6 ports detected [ 0.657450] hub 1-0:1.0: USB hub found [ 0.657475] hub 1-0:1.0: 3 ports detected [ 0.657626] ehci-pci 0000:00:13.2: EHCI Host Controller [ 0.657632] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 0.657636] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 0.657646] ehci-pci 0000:00:13.2: debug port 1 [ 0.657694] ehci-pci 0000:00:13.2: irq 19, io mem 0xfe029000 [ 0.670663] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 0.670814] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.08 [ 0.670822] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.670827] usb usb3: Product: EHCI Host Controller [ 0.670832] usb usb3: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ehci_hcd [ 0.670836] usb usb3: SerialNumber: 0000:00:13.2 [ 0.670973] hub 3-0:1.0: USB hub found [ 0.670979] hub 3-0:1.0: 6 ports detected [ 0.671114] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 0.671119] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 0.671136] ohci-pci 0000:00:12.1: irq 16, io mem 0xfe02d000 [ 0.731385] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.08 [ 0.731389] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.731391] usb usb4: Product: OHCI PCI host controller [ 0.731393] usb usb4: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ohci_hcd [ 0.731394] usb usb4: SerialNumber: 0000:00:12.1 [ 0.731483] hub 4-0:1.0: USB hub found [ 0.731492] hub 4-0:1.0: 3 ports detected [ 0.731739] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 0.731743] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 0.731776] ohci-pci 0000:00:13.0: irq 18, io mem 0xfe02b000 [ 0.791385] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.08 [ 0.791389] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.791391] usb usb5: Product: OHCI PCI host controller [ 0.791393] usb usb5: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ohci_hcd [ 0.791394] usb usb5: SerialNumber: 0000:00:13.0 [ 0.791489] hub 5-0:1.0: USB hub found [ 0.791497] hub 5-0:1.0: 3 ports detected [ 0.791721] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 0.791728] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 0.791744] ohci-pci 0000:00:13.1: irq 18, io mem 0xfe02a000 [ 0.830654] ata1: SATA link down (SStatus 0 SControl 300) [ 0.830737] ata4: SATA link down (SStatus 0 SControl 300) [ 0.840634] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.851374] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.08 [ 0.851378] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.851380] usb usb6: Product: OHCI PCI host controller [ 0.851382] usb usb6: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ohci_hcd [ 0.851383] usb usb6: SerialNumber: 0000:00:13.1 [ 0.851474] hub 6-0:1.0: USB hub found [ 0.851482] hub 6-0:1.0: 3 ports detected [ 0.851702] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 0.851707] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 0.851723] ohci-pci 0000:00:14.5: irq 18, io mem 0xfe028000 [ 0.911350] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.08 [ 0.911354] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.911356] usb usb7: Product: OHCI PCI host controller [ 0.911358] usb usb7: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 ohci_hcd [ 0.911360] usb usb7: SerialNumber: 0000:00:14.5 [ 0.911448] hub 7-0:1.0: USB hub found [ 0.911456] hub 7-0:1.0: 2 ports detected [ 0.911593] usbcore: registered new interface driver usbserial_generic [ 0.911598] usbserial: USB Serial support registered for generic [ 0.911665] rtc_cmos 00:02: RTC can wake from S4 [ 0.911871] rtc_cmos 00:02: registered as rtc0 [ 0.911896] rtc_cmos 00:02: setting system clock to 2024-05-24T13:40:52 UTC (1716558052) [ 0.911923] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.911963] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 0.912257] ledtrig-cpu: registered to indicate activity on CPUs [ 0.912741] [drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0 [ 0.917478] Console: switching to colour frame buffer device 160x64 [ 0.923496] simple-framebuffer simple-framebuffer.0: [drm] fb0: simpledrmdrmfb frame buffer device [ 0.923546] hid: raw HID events driver (C) Jiri Kosina [ 0.923649] drop_monitor: Initializing network drop monitor service [ 0.923997] NET: Registered PF_INET6 protocol family [ 0.930194] Segment Routing with IPv6 [ 0.930197] RPL Segment Routing with IPv6 [ 0.930212] In-situ OAM (IOAM) with IPv6 [ 0.930238] NET: Registered PF_PACKET protocol family [ 0.930276] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 0.930966] microcode: Current revision: 0x06000852 [ 0.930968] microcode: Updated early from: 0x06000822 [ 0.931118] IPI shorthand broadcast: enabled [ 0.933593] sched_clock: Marking stable (933611202, -2516524)->(2158705431, -1227610753) [ 0.933785] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.933924] registered taskstats version 1 [ 0.934271] Loading compiled-in X.509 certificates [ 0.938631] Loaded X.509 cert 'Build time autogenerated kernel key: ba55771f1c59367dcf377aa29b9b4f7948b6e0ec' [ 0.941067] Key type .fscrypt registered [ 0.941068] Key type fscrypt-provisioning registered [ 0.941445] PM: Magic number: 8:309:686 [ 0.945194] RAS: Correctable Errors collector initialized. [ 0.958652] clk: Disabling unused clocks [ 0.958655] PM: genpd: Disabling unused power domains [ 0.991707] usb 2-1: New USB device found, idVendor=0bda, idProduct=b812, bcdDevice= 2.10 [ 0.991711] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 0.991713] usb 2-1: Product: USB3.0 802.11ac 1200M Adapter [ 0.991715] usb 2-1: Manufacturer: Realtek [ 0.991716] usb 2-1: SerialNumber: 123456 [ 0.993952] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.993990] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.994127] ata2.00: ATA-11: Apacer AS340 120GB, AP612PE0, max UDMA/133 [ 0.994171] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.994361] ata2.00: configured for UDMA/133 [ 0.994793] ata3.00: ATA-8: TOSHIBA HDWD110, MS2OA8J0, max UDMA/133 [ 0.995062] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.996129] ata3.00: configured for UDMA/133 [ 1.020864] scsi 1:0:0:0: Direct-Access ATA Apacer AS340 120 2PE0 PQ: 0 ANSI: 5 [ 1.021144] sd 1:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 1.021154] sd 1:0:0:0: [sda] Write Protect is off [ 1.021156] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.021170] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.021189] sd 1:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.021602] scsi 2:0:0:0: Direct-Access ATA TOSHIBA HDWD110 A8J0 PQ: 0 ANSI: 5 [ 1.021734] sda: sda1 sda2 [ 1.021800] sd 1:0:0:0: [sda] Attached SCSI disk [ 1.021950] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.021952] sd 2:0:0:0: [sdb] 4096-byte physical blocks [ 1.021960] sd 2:0:0:0: [sdb] Write Protect is off [ 1.021962] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.021975] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.021994] sd 2:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 1.031122] sdb: sdb1 sdb2 [ 1.031208] sd 2:0:0:0: [sdb] Attached SCSI disk [ 1.034340] Freeing unused decrypted memory: 2028K [ 1.035063] Freeing unused kernel image (initmem) memory: 3468K [ 1.037297] Write protecting the kernel read-only data: 30720k [ 1.037971] Freeing unused kernel image (rodata/data gap) memory: 1312K [ 1.078468] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.078472] rodata_test: all tests were successful [ 1.078477] Run /init as init process [ 1.078478] with arguments: [ 1.078479] /init [ 1.078480] with environment: [ 1.078481] HOME=/ [ 1.078482] TERM=linux [ 1.078483] BOOT_IMAGE=/vmlinuz-linux-mainline [ 1.313649] scsi host4: pata_atiixp [ 1.313761] scsi host5: pata_atiixp [ 1.313792] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14 lpm-pol 0 [ 1.313794] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15 lpm-pol 0 [ 1.330836] usb 1-3: new low-speed USB device number 2 using ohci-pci [ 1.330865] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 1.330873] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8 [ 1.330949] xhci_hcd 0000:02:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000000000000890 [ 1.331106] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 1.331110] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9 [ 1.331113] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 1.331419] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.08 [ 1.331422] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.331424] usb usb8: Product: xHCI Host Controller [ 1.331426] usb usb8: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 xhci-hcd [ 1.331428] usb usb8: SerialNumber: 0000:02:00.0 [ 1.331538] hub 8-0:1.0: USB hub found [ 1.331546] hub 8-0:1.0: 1 port detected [ 1.331754] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.08 [ 1.331757] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.331760] usb usb9: Product: xHCI Host Controller [ 1.331761] usb usb9: Manufacturer: Linux 6.8.0-1-mainline-08073-g480e035fc4c7 xhci-hcd [ 1.331763] usb usb9: SerialNumber: 0000:02:00.0 [ 1.331937] hub 9-0:1.0: USB hub found [ 1.331947] hub 9-0:1.0: 4 ports detected [ 1.490437] tsc: Refined TSC clocksource calibration: 3322.065 MHz [ 1.490458] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2fe2b83769a, max_idle_ns: 440795214495 ns [ 1.490542] clocksource: Switched to clocksource tsc [ 1.514930] usb 1-3: New USB device found, idVendor=0c45, idProduct=7603, bcdDevice= 1.06 [ 1.514934] usb 1-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 1.514936] usb 1-3: Product: USB Keyboard [ 1.538363] usbcore: registered new interface driver usbhid [ 1.538366] usbhid: USB HID core driver [ 1.544886] input: USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.0/0003:0C45:7603.0001/input/input2 [ 1.580908] usb 8-1: new high-speed USB device number 2 using xhci_hcd [ 1.601675] hid-generic 0003:0C45:7603.0001: input,hidraw0: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:00:12.0-3/input0 [ 1.602220] input: USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input3 [ 1.657557] input: USB Keyboard System Control as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input4 [ 1.657685] input: USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input6 [ 1.657834] hid-generic 0003:0C45:7603.0002: input,hiddev96,hidraw1: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:00:12.0-3/input1 [ 1.722148] usb 8-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20 [ 1.722153] usb 8-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.722155] usb 8-1: Product: USB2.0 Hub [ 1.722853] hub 8-1:1.0: USB hub found [ 1.723047] hub 8-1:1.0: 4 ports detected [ 2.154223] usb 4-1: new full-speed USB device number 2 using ohci-pci [ 2.294237] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.294597] ata2.00: configured for UDMA/133 [ 2.348953] usb 4-1: New USB device found, idVendor=04d9, idProduct=a088, bcdDevice= 1.00 [ 2.348959] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.348961] usb 4-1: Product: USB Gaming Mouse [ 2.348964] usb 4-1: Manufacturer: RH [ 2.356258] input: RH USB Gaming Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.0/0003:04D9:A088.0003/input/input7 [ 2.411290] hid-generic 0003:04D9:A088.0003: input,hidraw2: USB HID v1.10 Keyboard [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input0 [ 2.417688] input: RH USB Gaming Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input8 [ 2.417770] input: RH USB Gaming Mouse System Control as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input9 [ 2.474486] input: RH USB Gaming Mouse Consumer Control as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input10 [ 2.474633] hid-generic 0003:04D9:A088.0004: input,hiddev97,hidraw3: USB HID v1.10 Mouse [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input1 [ 2.478402] hid-generic 0003:04D9:A088.0005: hiddev98,hidraw4: USB HID v1.10 Device [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input2 [ 3.050908] ata2.00: exception Emask 0x10 SAct 0x20000 SErr 0x40d0002 action 0xe frozen [ 3.050921] ata2.00: irq_stat 0x00000040, connection status changed [ 3.050925] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 3.050933] ata2.00: failed command: READ FPDMA QUEUED [ 3.050936] ata2.00: cmd 60/08:88:80:ff:f1/00:00:0d:00:00/40 tag 17 ncq dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 3.050953] ata2.00: status: { DRDY } [ 3.050959] ata2: hard resetting link [ 3.947573] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.947965] ata2.00: configured for UDMA/133 [ 3.958113] sd 1:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 3.958116] sd 1:0:0:0: [sda] tag#17 Sense Key : Illegal Request [current] [ 3.958118] sd 1:0:0:0: [sda] tag#17 Add. Sense: Unaligned write command [ 3.958121] sd 1:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 0d f1 ff 80 00 00 08 00 [ 3.958122] I/O error, dev sda, sector 233963392 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 3.958131] ata2: EH complete [ 4.119758] EXT4-fs (sda2): mounted filesystem 963daeed-0888-4658-9f17-18bd343dfb2a r/w with ordered data mode. Quota mode: none. [ 4.289536] systemd[1]: systemd 255.6-2-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified) [ 4.289542] systemd[1]: Detected architecture x86-64. [ 4.804287] systemd[1]: bpf-lsm: LSM BPF program attached [ 4.860959] ata2.00: exception Emask 0x10 SAct 0x200000 SErr 0x40d0002 action 0xe frozen [ 4.860971] ata2.00: irq_stat 0x00000040, connection status changed [ 4.860976] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 4.860984] ata2.00: failed command: READ FPDMA QUEUED [ 4.860987] ata2.00: cmd 60/08:a8:50:f9:08/00:00:07:00:00/40 tag 21 ncq dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 4.861003] ata2.00: status: { DRDY } [ 4.861010] ata2: hard resetting link [ 5.907577] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.908058] ata2.00: configured for UDMA/133 [ 5.918213] ata2: EH complete [ 6.032337] systemd-fstab-generator[269]: Mount point is not a valid path, ignoring. [ 6.033616] systemd-fstab-generator[269]: Mount point is not a valid path, ignoring. [ 6.657546] random: crng init done [ 6.730961] ata2: limiting SATA link speed to 1.5 Gbps [ 6.730971] ata2.00: exception Emask 0x10 SAct 0x30 SErr 0x40d0002 action 0xe frozen [ 6.730978] ata2.00: irq_stat 0x00000040, connection status changed [ 6.730982] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 6.730989] ata2.00: failed command: READ FPDMA QUEUED [ 6.730993] ata2.00: cmd 60/40:20:28:3d:9c/00:00:01:00:00/40 tag 4 ncq dma 32768 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 6.731008] ata2.00: status: { DRDY } [ 6.731013] ata2.00: failed command: READ FPDMA QUEUED [ 6.731016] ata2.00: cmd 60/08:28:30:04:ad/00:00:01:00:00/40 tag 5 ncq dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 6.731029] ata2.00: status: { DRDY } [ 6.731036] ata2: hard resetting link [ 7.910908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 7.911335] ata2.00: configured for UDMA/133 [ 7.921433] sd 1:0:0:0: [sda] tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=1s [ 7.921437] sd 1:0:0:0: [sda] tag#4 Sense Key : Illegal Request [current] [ 7.921439] sd 1:0:0:0: [sda] tag#4 Add. Sense: Unaligned write command [ 7.921441] sd 1:0:0:0: [sda] tag#4 CDB: Read(10) 28 00 01 9c 3d 28 00 00 40 00 [ 7.921443] I/O error, dev sda, sector 27016488 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0 [ 7.921451] sd 1:0:0:0: [sda] tag#5 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=1s [ 7.921453] sd 1:0:0:0: [sda] tag#5 Sense Key : Illegal Request [current] [ 7.921455] sd 1:0:0:0: [sda] tag#5 Add. Sense: Unaligned write command [ 7.921456] sd 1:0:0:0: [sda] tag#5 CDB: Read(10) 28 00 01 ad 04 30 00 00 08 00 [ 7.921457] I/O error, dev sda, sector 28116016 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7.921463] ata2: EH complete [ 7.935697] zram: Added device: zram0 [ 8.102998] systemd[1]: Queued start job for default target Graphical Interface. [ 8.132197] systemd[1]: Created slice Slice /system/dirmngr. [ 8.132587] systemd[1]: Created slice Slice /system/getty. [ 8.132925] systemd[1]: Created slice Slice /system/gpg-agent. [ 8.133237] systemd[1]: Created slice Slice /system/gpg-agent-browser. [ 8.133545] systemd[1]: Created slice Slice /system/gpg-agent-extra. [ 8.133851] systemd[1]: Created slice Slice /system/gpg-agent-ssh. [ 8.134193] systemd[1]: Created slice Slice /system/keyboxd. [ 8.134508] systemd[1]: Created slice Slice /system/modprobe. [ 8.134816] systemd[1]: Created slice Slice /system/systemd-fsck. [ 8.135128] systemd[1]: Created slice Slice /system/systemd-zram-setup. [ 8.135353] systemd[1]: Created slice User and Session Slice. [ 8.135412] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 8.135456] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 8.135604] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 8.135624] systemd[1]: Expecting device /dev/disk/by-uuid/03ce297b-4be8-4886-953d-2d2cc4bd0862... [ 8.135631] systemd[1]: Expecting device /dev/disk/by-uuid/6BB1-1CFA... [ 8.135638] systemd[1]: Expecting device /dev/zram0... [ 8.135648] systemd[1]: Reached target Local Encrypted Volumes. [ 8.135666] systemd[1]: Reached target Local Integrity Protected Volumes. [ 8.135695] systemd[1]: Reached target Path Units. [ 8.135708] systemd[1]: Reached target Remote File Systems. [ 8.135719] systemd[1]: Reached target Slice Units. [ 8.135747] systemd[1]: Reached target Local Verity Protected Volumes. [ 8.135816] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 8.136163] systemd[1]: Listening on LVM2 poll daemon socket. [ 8.137672] systemd[1]: Listening on Process Core Dump Socket. [ 8.137780] systemd[1]: Listening on Journal Socket (/dev/log). [ 8.137886] systemd[1]: Listening on Journal Socket. [ 8.138019] systemd[1]: Listening on Network Service Netlink Socket. [ 8.138038] systemd[1]: TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 8.138393] systemd[1]: Listening on udev Control Socket. [ 8.138476] systemd[1]: Listening on udev Kernel Socket. [ 8.139578] systemd[1]: Mounting Huge Pages File System... [ 8.140139] systemd[1]: Mounting POSIX Message Queue File System... [ 8.150911] systemd[1]: Mounting Kernel Debug File System... [ 8.151557] systemd[1]: Mounting Kernel Trace File System... [ 8.162835] systemd[1]: Starting Create List of Static Device Nodes... [ 8.167975] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... [ 8.175823] systemd[1]: Starting Load Kernel Module configfs... [ 8.183121] systemd[1]: Starting Load Kernel Module dm_mod... [ 8.191347] systemd[1]: Starting Load Kernel Module drm... [ 8.193922] systemd[1]: Starting Load Kernel Module fuse... [ 8.197959] systemd[1]: Starting Load Kernel Module loop... [ 8.198007] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 8.217879] systemd[1]: Starting Journal Service... [ 8.230249] systemd[1]: Starting Load Kernel Modules... [ 8.238614] device-mapper: uevent: version 1.0.3 [ 8.239723] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 8.240277] systemd[1]: Starting Generate network units from Kernel command line... [ 8.240308] systemd[1]: TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 8.270833] loop: module loaded [ 8.288807] systemd[1]: Starting Remount Root and Kernel File Systems... [ 8.288879] systemd[1]: TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 8.290376] fuse: init (API version 7.39) [ 8.290559] systemd[1]: Starting Coldplug All udev Devices... [ 8.291954] systemd[1]: Mounted Huge Pages File System. [ 8.292046] systemd[1]: Mounted POSIX Message Queue File System. [ 8.292119] systemd[1]: Mounted Kernel Debug File System. [ 8.292194] systemd[1]: Mounted Kernel Trace File System. [ 8.292378] systemd[1]: Finished Create List of Static Device Nodes. [ 8.292642] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 8.292772] systemd[1]: Finished Load Kernel Module configfs. [ 8.292999] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. [ 8.293125] systemd[1]: Finished Load Kernel Module dm_mod. [ 8.293347] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 8.293473] systemd[1]: Finished Load Kernel Module drm. [ 8.293696] systemd[1]: modprobe@loop.service: Deactivated successfully. [ 8.293820] systemd[1]: Finished Load Kernel Module loop. [ 8.308367] systemd[1]: Mounting Kernel Configuration File System... [ 8.308668] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met. [ 8.314378] systemd-journald[293]: Collecting audit messages is disabled. [ 8.320785] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 8.320886] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 8.343920] Asymmetric key parser 'pkcs8' registered [ 8.344099] systemd[1]: Starting Create Static Device Nodes in /dev gracefully... [ 8.344554] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling. [ 8.344827] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 8.344979] systemd[1]: Finished Load Kernel Module fuse. [ 8.345222] systemd[1]: Finished Generate network units from Kernel command line. [ 8.350872] systemd[1]: Mounting FUSE Control File System... [ 8.351080] systemd[1]: Finished Load Kernel Modules. [ 8.377541] EXT4-fs (sda2): re-mounted 963daeed-0888-4658-9f17-18bd343dfb2a r/w. Quota mode: none. [ 8.384289] systemd[1]: Starting Apply Kernel Variables... [ 8.385229] systemd[1]: Finished Remount Root and Kernel File Systems. [ 8.385361] systemd[1]: Mounted Kernel Configuration File System. [ 8.391551] systemd[1]: Rebuild Hardware Database was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc). [ 8.401061] systemd[1]: Starting Load/Save OS Random Seed... [ 8.405640] systemd[1]: TPM2 SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 8.411230] systemd[1]: Mounted FUSE Control File System. [ 8.424941] systemd[1]: Finished Apply Kernel Variables. [ 8.442480] systemd[1]: Finished Load/Save OS Random Seed. [ 8.454415] systemd[1]: Finished Create Static Device Nodes in /dev gracefully. [ 8.454520] systemd[1]: Create System Users was skipped because no trigger condition checks were met. [ 8.481070] systemd[1]: Starting Create Static Device Nodes in /dev... [ 8.483168] systemd[1]: Started Journal Service. [ 8.516388] systemd-journald[293]: Received client request to flush runtime journal. [ 8.525883] systemd-journald[293]: /var/log/journal/ca3d73a04dc345538c9904a96756e41e/system.journal: Journal file uses a different sequence number ID, rotating. [ 8.525887] systemd-journald[293]: Rotating system journal. [ 8.709389] zram0: detected capacity change from 0 to 8388608 [ 8.912770] Adding 4194300k swap on /dev/zram0. Priority:100 extents:1 across:4194300k SSDsc [ 8.988845] mousedev: PS/2 mouse device common for all mice [ 9.373138] acpi_cpufreq: overriding BIOS provided _PSD data [ 9.388627] ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B08 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0F (\SOR1) (20230628/utaddress-204) [ 9.388636] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 9.422698] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver [ 9.423211] sp5100-tco sp5100-tco: Failed to reserve MMIO or alternate MMIO region [ 9.423214] sp5100-tco: probe of sp5100-tco failed with error -16 [ 9.471108] input: PC Speaker as /devices/platform/pcspkr/input/input12 [ 9.480563] parport_pc 00:04: reported by Plug and Play ACPI [ 9.484174] cryptd: max_cpu_qlen set to 1000 [ 9.484462] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 9.558944] AVX version of gcm_enc/dec engaged. [ 9.558995] AES CTR mode by8 optimization enabled [ 9.573845] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control [ 9.589925] r8169 0000:03:00.0 eth0: RTL8168g/8111g, e0:d5:5e:3b:15:1f, XID 4c0, IRQ 28 [ 9.589930] r8169 0000:03:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] [ 9.612035] r8169 0000:03:00.0 enp3s0: renamed from eth0 [ 9.631260] ppdev: user-space parallel port driver [ 9.635755] EXT4-fs (sdb1): mounted filesystem 03ce297b-4be8-4886-953d-2d2cc4bd0862 r/w with ordered data mode. Quota mode: none. [ 9.751020] snd_hda_intel 0000:01:00.1: Disabling MSI [ 9.751032] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client [ 9.815753] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input13 [ 9.815849] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input14 [ 9.815900] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input15 [ 9.815946] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input16 [ 9.831879] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line [ 9.831885] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 9.831887] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 9.831890] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 9.831891] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x0 [ 9.831893] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 9.831894] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19 [ 9.831896] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18 [ 9.831898] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a [ 9.856717] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input17 [ 9.856773] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input18 [ 9.856826] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input19 [ 9.856873] input: HDA ATI SB Line Out as /devices/pci0000:00/0000:00:14.2/sound/card0/input20 [ 9.856920] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input21 [ 10.190847] kvm_amd: TSC scaling supported [ 10.190851] kvm_amd: Nested Virtualization enabled [ 10.190852] kvm_amd: Nested Paging enabled [ 10.190859] kvm_amd: LBR virtualization supported [ 10.904084] NET: Registered PF_ALG protocol family [ 11.034359] Generic FE-GE Realtek PHY r8169-0-300:00: attached PHY driver (mii_bus:phy_addr=r8169-0-300:00, irq=MAC) [ 11.224242] r8169 0000:03:00.0 enp3s0: Link is Down [ 14.387628] ata2.00: exception Emask 0x10 SAct 0x1000 SErr 0x40d0002 action 0xe frozen [ 14.387642] ata2.00: irq_stat 0x00000040, connection status changed [ 14.387646] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 14.387654] ata2.00: failed command: READ FPDMA QUEUED [ 14.387658] ata2.00: cmd 60/00:60:00:f9:d5/0a:00:0b:00:00/40 tag 12 ncq dma 1310720 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 14.387674] ata2.00: status: { DRDY } [ 14.387681] ata2: hard resetting link [ 15.284181] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 15.284596] ata2.00: configured for UDMA/133 [ 15.294755] sd 1:0:0:0: [sda] tag#12 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 15.294760] sd 1:0:0:0: [sda] tag#12 Sense Key : Illegal Request [current] [ 15.294764] sd 1:0:0:0: [sda] tag#12 Add. Sense: Unaligned write command [ 15.294768] sd 1:0:0:0: [sda] tag#12 CDB: Read(10) 28 00 0b d5 f9 00 00 0a 00 00 [ 15.294770] I/O error, dev sda, sector 198572288 op 0x0:(READ) flags 0x80700 phys_seg 21 prio class 0 [ 15.294792] ata2: EH complete [ 15.654295] ata2.00: exception Emask 0x10 SAct 0x40000 SErr 0x40d0002 action 0xe frozen [ 15.654309] ata2.00: irq_stat 0x00000040, connection status changed [ 15.654313] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 15.654321] ata2.00: failed command: WRITE FPDMA QUEUED [ 15.654325] ata2.00: cmd 61/08:90:00:97:a2/00:00:08:00:00/40 tag 18 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 15.654341] ata2.00: status: { DRDY } [ 15.654348] ata2: hard resetting link [ 16.550910] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 16.551386] ata2.00: configured for UDMA/133 [ 16.561567] ata2: EH complete [ 18.974248] ata2.00: exception Emask 0x10 SAct 0x20000 SErr 0x40d0002 action 0xe frozen [ 18.974261] ata2.00: irq_stat 0x00000040, connection status changed [ 18.974266] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 18.974274] ata2.00: failed command: READ FPDMA QUEUED [ 18.974277] ata2.00: cmd 60/10:88:48:a8:04/00:00:0b:00:00/40 tag 17 ncq dma 8192 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 18.974293] ata2.00: status: { DRDY } [ 18.974300] ata2: hard resetting link [ 19.877569] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 19.878012] ata2.00: configured for UDMA/133 [ 19.888161] sd 1:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=1s [ 19.888172] sd 1:0:0:0: [sda] tag#17 Sense Key : Illegal Request [current] [ 19.888178] sd 1:0:0:0: [sda] tag#17 Add. Sense: Unaligned write command [ 19.888184] sd 1:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 0b 04 a8 48 00 00 10 00 [ 19.888188] I/O error, dev sda, sector 184854600 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0 [ 19.888213] ata2: EH complete [ 20.061541] systemd-journald[293]: /var/log/journal/ca3d73a04dc345538c9904a96756e41e/user-1000.journal: Journal file uses a different sequence number ID, rotating. [ 21.624296] ata2.00: limiting speed to UDMA/100:PIO4 [ 21.624307] ata2.00: exception Emask 0x10 SAct 0x2000 SErr 0x40d0002 action 0xe frozen [ 21.624314] ata2.00: irq_stat 0x00000040, connection status changed [ 21.624318] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 21.624325] ata2.00: failed command: READ FPDMA QUEUED [ 21.624328] ata2.00: cmd 60/00:68:60:07:49/01:00:02:00:00/40 tag 13 ncq dma 131072 in res 40/00:58:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) [ 21.624345] ata2.00: status: { DRDY } [ 21.624352] ata2: hard resetting link [ 22.520957] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 22.521405] ata2.00: configured for UDMA/100 [ 22.531593] sd 1:0:0:0: [sda] tag#13 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 22.531603] sd 1:0:0:0: [sda] tag#13 Sense Key : Illegal Request [current] [ 22.531610] sd 1:0:0:0: [sda] tag#13 Add. Sense: Unaligned write command [ 22.531616] sd 1:0:0:0: [sda] tag#13 CDB: Read(10) 28 00 02 49 07 60 00 01 00 00 [ 22.531620] I/O error, dev sda, sector 38340448 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 22.531648] ata2: EH complete [ 25.257673] ata2.00: exception Emask 0x10 SAct 0x80cff01f SErr 0x40d0002 action 0xe frozen [ 25.257686] ata2.00: irq_stat 0x00000040, connection status changed [ 25.257690] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 25.257698] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257701] ata2.00: cmd 61/08:00:80:f8:07/00:00:02:00:00/40 tag 0 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257717] ata2.00: status: { DRDY } [ 25.257722] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257725] ata2.00: cmd 61/08:08:08:f9:07/00:00:02:00:00/40 tag 1 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257737] ata2.00: status: { DRDY } [ 25.257742] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257745] ata2.00: cmd 61/10:10:28:f9:07/00:00:02:00:00/40 tag 2 ncq dma 8192 out res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257757] ata2.00: status: { DRDY } [ 25.257761] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257764] ata2.00: cmd 61/08:18:40:fb:07/00:00:02:00:00/40 tag 3 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257776] ata2.00: status: { DRDY } [ 25.257780] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257783] ata2.00: cmd 61/08:20:30:fa:08/00:00:02:00:00/40 tag 4 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257795] ata2.00: status: { DRDY } [ 25.257800] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257802] ata2.00: cmd 61/18:60:08:f8:07/00:00:00:00:00/40 tag 12 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257815] ata2.00: status: { DRDY } [ 25.257819] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257821] ata2.00: cmd 61/10:68:28:f8:07/00:00:00:00:00/40 tag 13 ncq dma 8192 out res 40/00:58:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) [ 25.257834] ata2.00: status: { DRDY } [ 25.257838] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257841] ata2.00: cmd 61/08:70:40:f8:07/00:00:00:00:00/40 tag 14 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257853] ata2.00: status: { DRDY } [ 25.257857] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257860] ata2.00: cmd 61/18:78:50:f8:07/00:00:00:00:00/40 tag 15 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257872] ata2.00: status: { DRDY } [ 25.257876] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257878] ata2.00: cmd 61/08:80:78:18:08/00:00:00:00:00/40 tag 16 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257891] ata2.00: status: { DRDY } [ 25.257895] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257897] ata2.00: cmd 61/08:88:80:1c:09/00:00:00:00:00/40 tag 17 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257910] ata2.00: status: { DRDY } [ 25.257914] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257916] ata2.00: cmd 61/08:90:28:f8:c7/00:00:00:00:00/40 tag 18 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257929] ata2.00: status: { DRDY } [ 25.257932] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257935] ata2.00: cmd 61/08:98:08:f8:07/00:00:01:00:00/40 tag 19 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257947] ata2.00: status: { DRDY } [ 25.257951] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257954] ata2.00: cmd 61/08:b0:70:f8:47/00:00:01:00:00/40 tag 22 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257966] ata2.00: status: { DRDY } [ 25.257970] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257973] ata2.00: cmd 61/08:b8:d8:fa:c7/00:00:01:00:00/40 tag 23 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.257985] ata2.00: status: { DRDY } [ 25.257989] ata2.00: failed command: WRITE FPDMA QUEUED [ 25.257992] ata2.00: cmd 61/08:f8:08:f8:07/00:00:02:00:00/40 tag 31 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 25.258004] ata2.00: status: { DRDY } [ 25.258010] ata2: hard resetting link [ 26.414238] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 26.414746] ata2.00: configured for UDMA/100 [ 26.424980] ata2: EH complete [ 28.677624] ata2.00: exception Emask 0x10 SAct 0x8000000 SErr 0x40d0002 action 0xe frozen [ 28.677636] ata2.00: irq_stat 0x00000040, connection status changed [ 28.677641] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 28.677649] ata2.00: failed command: WRITE FPDMA QUEUED [ 28.677652] ata2.00: cmd 61/18:d8:90:87:cd/00:00:06:00:00/40 tag 27 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 28.677668] ata2.00: status: { DRDY } [ 28.677675] ata2: hard resetting link [ 29.574245] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 29.574735] ata2.00: configured for UDMA/100 [ 29.584915] ata2: EH complete [ 34.644289] ata2.00: exception Emask 0x10 SAct 0x2000 SErr 0x40d0002 action 0xe frozen [ 34.644302] ata2.00: irq_stat 0x00000040, connection status changed [ 34.644306] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 34.644313] ata2.00: failed command: WRITE FPDMA QUEUED [ 34.644317] ata2.00: cmd 61/20:68:b0:87:cd/00:00:06:00:00/40 tag 13 ncq dma 16384 out res 40/00:58:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) [ 34.644333] ata2.00: status: { DRDY } [ 34.644340] ata2: hard resetting link [ 35.540892] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 35.541384] ata2.00: configured for UDMA/100 [ 35.551566] ata2: EH complete [ 36.570957] ata2.00: limiting speed to UDMA/33:PIO4 [ 36.570967] ata2.00: exception Emask 0x10 SAct 0x200000 SErr 0x40d0002 action 0xe frozen [ 36.570974] ata2.00: irq_stat 0x00000040, connection status changed [ 36.570978] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 36.570985] ata2.00: failed command: READ FPDMA QUEUED [ 36.570988] ata2.00: cmd 60/58:a8:a8:b3:50/04:00:05:00:00/40 tag 21 ncq dma 569344 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 36.571004] ata2.00: status: { DRDY } [ 36.571010] ata2: hard resetting link [ 37.467572] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 37.467989] ata2.00: configured for UDMA/33 [ 37.478179] sd 1:0:0:0: [sda] tag#21 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 37.478189] sd 1:0:0:0: [sda] tag#21 Sense Key : Illegal Request [current] [ 37.478196] sd 1:0:0:0: [sda] tag#21 Add. Sense: Unaligned write command [ 37.478202] sd 1:0:0:0: [sda] tag#21 CDB: Read(10) 28 00 05 50 b3 a8 00 04 58 00 [ 37.478206] I/O error, dev sda, sector 89174952 op 0x0:(READ) flags 0x80700 phys_seg 131 prio class 0 [ 37.478237] ata2: EH complete [ 40.320952] ata2.00: exception Emask 0x10 SAct 0x4 SErr 0x40d0002 action 0xe frozen [ 40.320965] ata2.00: irq_stat 0x00000040, connection status changed [ 40.320969] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 40.320976] ata2.00: failed command: READ FPDMA QUEUED [ 40.320980] ata2.00: cmd 60/00:10:40:9b:86/01:00:06:00:00/40 tag 2 ncq dma 131072 in res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 40.320995] ata2.00: status: { DRDY } [ 40.321002] ata2: hard resetting link [ 41.187566] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 41.188054] ata2.00: configured for UDMA/33 [ 41.198241] sd 1:0:0:0: [sda] tag#2 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 41.198250] sd 1:0:0:0: [sda] tag#2 Sense Key : Illegal Request [current] [ 41.198256] sd 1:0:0:0: [sda] tag#2 Add. Sense: Unaligned write command [ 41.198262] sd 1:0:0:0: [sda] tag#2 CDB: Read(10) 28 00 06 86 9b 40 00 01 00 00 [ 41.198265] I/O error, dev sda, sector 109484864 op 0x0:(READ) flags 0x80700 phys_seg 31 prio class 0 [ 41.198293] ata2: EH complete [ 45.137574] ata2.00: exception Emask 0x10 SAct 0x200 SErr 0x40d0002 action 0xe frozen [ 45.137588] ata2.00: irq_stat 0x00000040, connection status changed [ 45.137592] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 45.137600] ata2.00: failed command: READ FPDMA QUEUED [ 45.137604] ata2.00: cmd 60/20:48:28:5d:0d/00:00:07:00:00/40 tag 9 ncq dma 16384 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 45.137619] ata2.00: status: { DRDY } [ 45.137627] ata2: hard resetting link [ 46.034230] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 46.034722] ata2.00: configured for UDMA/33 [ 46.044912] sd 1:0:0:0: [sda] tag#9 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 46.044922] sd 1:0:0:0: [sda] tag#9 Sense Key : Illegal Request [current] [ 46.044929] sd 1:0:0:0: [sda] tag#9 Add. Sense: Unaligned write command [ 46.044935] sd 1:0:0:0: [sda] tag#9 CDB: Read(10) 28 00 07 0d 5d 28 00 00 20 00 [ 46.044939] I/O error, dev sda, sector 118316328 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 46.044964] ata2: EH complete [ 47.007566] ata2.00: exception Emask 0x10 SAct 0x4000 SErr 0x40d0002 action 0xe frozen [ 47.007579] ata2.00: irq_stat 0x00000040, connection status changed [ 47.007583] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 47.007591] ata2.00: failed command: READ FPDMA QUEUED [ 47.007594] ata2.00: cmd 60/20:70:00:bc:0c/00:00:07:00:00/40 tag 14 ncq dma 16384 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 47.007610] ata2.00: status: { DRDY } [ 47.007617] ata2: hard resetting link [ 47.904231] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 47.904703] ata2.00: configured for UDMA/33 [ 47.914902] sd 1:0:0:0: [sda] tag#14 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 47.914919] sd 1:0:0:0: [sda] tag#14 Sense Key : Illegal Request [current] [ 47.914926] sd 1:0:0:0: [sda] tag#14 Add. Sense: Unaligned write command [ 47.914933] sd 1:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 07 0c bc 00 00 00 20 00 [ 47.914937] I/O error, dev sda, sector 118275072 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 47.914962] ata2: EH complete [ 51.717622] ata2.00: exception Emask 0x10 SAct 0x4000 SErr 0x40d0002 action 0xe frozen [ 51.717635] ata2.00: irq_stat 0x00000040, connection status changed [ 51.717639] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 51.717647] ata2.00: failed command: WRITE FPDMA QUEUED [ 51.717651] ata2.00: cmd 61/20:70:88:88:cd/00:00:06:00:00/40 tag 14 ncq dma 16384 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 51.717667] ata2.00: status: { DRDY } [ 51.717675] ata2: hard resetting link [ 52.614228] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 52.614681] ata2.00: configured for UDMA/33 [ 52.624862] ata2: EH complete [ 54.697626] ata2.00: exception Emask 0x10 SAct 0x80e00000 SErr 0x40d0002 action 0xe frozen [ 54.697638] ata2.00: irq_stat 0x00000040, connection status changed [ 54.697643] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 54.697650] ata2.00: failed command: WRITE FPDMA QUEUED [ 54.697654] ata2.00: cmd 61/00:a8:20:78:de/02:00:0a:00:00/40 tag 21 ncq dma 262144 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 54.697669] ata2.00: status: { DRDY } [ 54.697674] ata2.00: failed command: WRITE FPDMA QUEUED [ 54.697677] ata2.00: cmd 61/d8:b0:68:fb:e4/01:00:0a:00:00/40 tag 22 ncq dma 241664 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 54.697691] ata2.00: status: { DRDY } [ 54.697695] ata2.00: failed command: WRITE FPDMA QUEUED [ 54.697698] ata2.00: cmd 61/08:b8:10:68:f1/00:00:07:00:00/40 tag 23 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 54.697711] ata2.00: status: { DRDY } [ 54.697715] ata2.00: failed command: WRITE FPDMA QUEUED [ 54.697718] ata2.00: cmd 61/08:f8:18:68:f1/00:00:07:00:00/40 tag 31 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 54.697730] ata2.00: status: { DRDY } [ 54.697736] ata2: hard resetting link [ 55.594236] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 55.594739] ata2.00: configured for UDMA/33 [ 55.604929] ata2: EH complete [ 57.690952] ata2.00: exception Emask 0x10 SAct 0x1000 SErr 0x40d0002 action 0xe frozen [ 57.690965] ata2.00: irq_stat 0x00000040, connection status changed [ 57.690969] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 57.690977] ata2.00: failed command: WRITE FPDMA QUEUED [ 57.690980] ata2.00: cmd 61/18:60:b0:88:cd/00:00:06:00:00/40 tag 12 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 57.690996] ata2.00: status: { DRDY } [ 57.691003] ata2: hard resetting link [ 58.587576] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 58.588069] ata2.00: configured for UDMA/33 [ 58.598248] ata2: EH complete [ 60.097622] ata2.00: exception Emask 0x10 SAct 0xc000 SErr 0x40d0002 action 0xe frozen [ 60.097635] ata2.00: irq_stat 0x00000040, connection status changed [ 60.097639] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 60.097648] ata2.00: failed command: READ FPDMA QUEUED [ 60.097651] ata2.00: cmd 60/20:70:70:9a:94/00:00:01:00:00/40 tag 14 ncq dma 16384 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 60.097667] ata2.00: status: { DRDY } [ 60.097672] ata2.00: failed command: READ FPDMA QUEUED [ 60.097675] ata2.00: cmd 60/20:78:f8:47:bc/00:00:0b:00:00/40 tag 15 ncq dma 16384 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 60.097688] ata2.00: status: { DRDY } [ 60.097695] ata2: hard resetting link [ 60.994215] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 60.994716] ata2.00: configured for UDMA/33 [ 61.004915] sd 1:0:0:0: [sda] tag#14 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 61.004932] sd 1:0:0:0: [sda] tag#14 Sense Key : Illegal Request [current] [ 61.004939] sd 1:0:0:0: [sda] tag#14 Add. Sense: Unaligned write command [ 61.004946] sd 1:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 01 94 9a 70 00 00 20 00 [ 61.004950] I/O error, dev sda, sector 26516080 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 61.004980] sd 1:0:0:0: [sda] tag#15 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 61.004987] sd 1:0:0:0: [sda] tag#15 Sense Key : Illegal Request [current] [ 61.004994] sd 1:0:0:0: [sda] tag#15 Add. Sense: Unaligned write command [ 61.005001] sd 1:0:0:0: [sda] tag#15 CDB: Read(10) 28 00 0b bc 47 f8 00 00 20 00 [ 61.005005] I/O error, dev sda, sector 196888568 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 61.005025] ata2: EH complete [ 63.210907] ata2.00: exception Emask 0x10 SAct 0x60000 SErr 0x40d0002 action 0xe frozen [ 63.210922] ata2.00: irq_stat 0x00000040, connection status changed [ 63.210926] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 63.210934] ata2.00: failed command: WRITE FPDMA QUEUED [ 63.210938] ata2.00: cmd 61/28:88:d0:88:cd/00:00:06:00:00/40 tag 17 ncq dma 20480 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 63.210954] ata2.00: status: { DRDY } [ 63.210958] ata2.00: failed command: READ FPDMA QUEUED [ 63.210961] ata2.00: cmd 60/20:90:f8:3c:35/00:00:02:00:00/40 tag 18 ncq dma 16384 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 63.210975] ata2.00: status: { DRDY } [ 63.210982] ata2: hard resetting link [ 64.107561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 64.108048] ata2.00: configured for UDMA/33 [ 64.118241] sd 1:0:0:0: [sda] tag#18 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 64.118251] sd 1:0:0:0: [sda] tag#18 Sense Key : Illegal Request [current] [ 64.118257] sd 1:0:0:0: [sda] tag#18 Add. Sense: Unaligned write command [ 64.118264] sd 1:0:0:0: [sda] tag#18 CDB: Read(10) 28 00 02 35 3c f8 00 00 20 00 [ 64.118267] I/O error, dev sda, sector 37043448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 64.118289] ata2: EH complete [ 64.944302] ata2.00: exception Emask 0x10 SAct 0x3fc SErr 0x40d0002 action 0xe frozen [ 64.944316] ata2.00: irq_stat 0x00000040, connection status changed [ 64.944321] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 64.944329] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944332] ata2.00: cmd 61/08:10:10:68:f1/00:00:07:00:00/40 tag 2 ncq dma 4096 out res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944348] ata2.00: status: { DRDY } [ 64.944353] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944356] ata2.00: cmd 61/10:18:28:78:de/00:00:0a:00:00/40 tag 3 ncq dma 8192 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944369] ata2.00: status: { DRDY } [ 64.944373] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944376] ata2.00: cmd 61/08:20:40:78:de/00:00:0a:00:00/40 tag 4 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944389] ata2.00: status: { DRDY } [ 64.944393] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944396] ata2.00: cmd 61/18:28:50:78:de/00:00:0a:00:00/40 tag 5 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944409] ata2.00: status: { DRDY } [ 64.944413] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944415] ata2.00: cmd 61/c0:30:70:78:de/00:00:0a:00:00/40 tag 6 ncq dma 98304 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944428] ata2.00: status: { DRDY } [ 64.944432] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944435] ata2.00: cmd 61/50:38:40:79:de/00:00:0a:00:00/40 tag 7 ncq dma 40960 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944447] ata2.00: status: { DRDY } [ 64.944451] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944454] ata2.00: cmd 61/38:40:98:79:de/00:00:0a:00:00/40 tag 8 ncq dma 28672 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944466] ata2.00: status: { DRDY } [ 64.944470] ata2.00: failed command: WRITE FPDMA QUEUED [ 64.944473] ata2.00: cmd 61/70:48:e0:79:de/00:00:0a:00:00/40 tag 9 ncq dma 57344 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 64.944485] ata2.00: status: { DRDY } [ 64.944492] ata2: hard resetting link [ 65.840950] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 65.841434] ata2.00: configured for UDMA/33 [ 65.851631] ata2: EH complete [ 66.437655] ata2.00: exception Emask 0x10 SAct 0x1fff80 SErr 0x40d0002 action 0xe frozen [ 66.437668] ata2.00: irq_stat 0x00000040, connection status changed [ 66.437672] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 66.437679] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437683] ata2.00: cmd 61/08:38:10:f8:07/00:00:00:00:00/40 tag 7 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437698] ata2.00: status: { DRDY } [ 66.437703] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437706] ata2.00: cmd 61/08:40:28:f8:07/00:00:00:00:00/40 tag 8 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437719] ata2.00: status: { DRDY } [ 66.437723] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437726] ata2.00: cmd 61/08:48:80:1c:09/00:00:00:00:00/40 tag 9 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437739] ata2.00: status: { DRDY } [ 66.437743] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437746] ata2.00: cmd 61/08:50:00:f8:c7/00:00:01:00:00/40 tag 10 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437759] ata2.00: status: { DRDY } [ 66.437763] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437766] ata2.00: cmd 61/08:58:98:f8:c7/00:00:01:00:00/40 tag 11 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437778] ata2.00: status: { DRDY } [ 66.437782] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437785] ata2.00: cmd 61/08:60:a0:f9:c7/00:00:01:00:00/40 tag 12 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437797] ata2.00: status: { DRDY } [ 66.437801] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437804] ata2.00: cmd 61/10:68:08:29:c8/00:00:01:00:00/40 tag 13 ncq dma 8192 out res 40/00:58:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) [ 66.437817] ata2.00: status: { DRDY } [ 66.437821] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437824] ata2.00: cmd 61/08:70:b8:f9:c8/00:00:01:00:00/40 tag 14 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437836] ata2.00: status: { DRDY } [ 66.437840] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437843] ata2.00: cmd 61/08:78:40:fb:07/00:00:02:00:00/40 tag 15 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437855] ata2.00: status: { DRDY } [ 66.437859] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437862] ata2.00: cmd 61/08:80:80:f8:87/00:00:04:00:00/40 tag 16 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437874] ata2.00: status: { DRDY } [ 66.437878] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437881] ata2.00: cmd 61/08:88:00:f9:87/00:00:04:00:00/40 tag 17 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437893] ata2.00: status: { DRDY } [ 66.437897] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437900] ata2.00: cmd 61/08:90:10:06:88/00:00:04:00:00/40 tag 18 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437912] ata2.00: status: { DRDY } [ 66.437916] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437919] ata2.00: cmd 61/08:98:70:0b:88/00:00:04:00:00/40 tag 19 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437931] ata2.00: status: { DRDY } [ 66.437935] ata2.00: failed command: WRITE FPDMA QUEUED [ 66.437937] ata2.00: cmd 61/08:a0:08:f9:88/00:00:04:00:00/40 tag 20 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 66.437949] ata2.00: status: { DRDY } [ 66.437956] ata2: hard resetting link [ 67.304240] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 67.304708] ata2.00: configured for UDMA/33 [ 67.314934] ata2: EH complete [ 68.784289] ata2.00: exception Emask 0x10 SAct 0x2000000 SErr 0x40d0002 action 0xe frozen [ 68.784304] ata2.00: irq_stat 0x00000040, connection status changed [ 68.784308] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 68.784317] ata2.00: failed command: WRITE FPDMA QUEUED [ 68.784320] ata2.00: cmd 61/18:c8:00:89:cd/00:00:06:00:00/40 tag 25 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 68.784336] ata2.00: status: { DRDY } [ 68.784343] ata2: hard resetting link [ 69.650880] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 69.651470] ata2.00: configured for UDMA/33 [ 69.661614] ata2: EH complete [ 74.750955] ata2.00: exception Emask 0x10 SAct 0x40 SErr 0x40d0002 action 0xe frozen [ 74.750969] ata2.00: irq_stat 0x00000040, connection status changed [ 74.750974] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 74.750982] ata2.00: failed command: WRITE FPDMA QUEUED [ 74.750986] ata2.00: cmd 61/20:30:20:89:cd/00:00:06:00:00/40 tag 6 ncq dma 16384 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 74.751002] ata2.00: status: { DRDY } [ 74.751009] ata2: hard resetting link [ 75.647558] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 75.648029] ata2.00: configured for UDMA/33 [ 75.658163] ata2: EH complete [ 80.720952] ata2.00: exception Emask 0x10 SAct 0x4000 SErr 0x40d0002 action 0xe frozen [ 80.720966] ata2.00: irq_stat 0x00000040, connection status changed [ 80.720970] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 80.720978] ata2.00: failed command: WRITE FPDMA QUEUED [ 80.720982] ata2.00: cmd 61/18:70:48:89:cd/00:00:06:00:00/40 tag 14 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 80.720998] ata2.00: status: { DRDY } [ 80.721005] ata2: hard resetting link [ 81.617571] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 81.618081] ata2.00: configured for UDMA/33 [ 81.628267] ata2: EH complete [ 86.694285] ata2.00: exception Emask 0x10 SAct 0x400000 SErr 0x40d0002 action 0xe frozen [ 86.694299] ata2.00: irq_stat 0x00000040, connection status changed [ 86.694304] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 86.694312] ata2.00: failed command: WRITE FPDMA QUEUED [ 86.694315] ata2.00: cmd 61/18:b0:68:89:cd/00:00:06:00:00/40 tag 22 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 86.694331] ata2.00: status: { DRDY } [ 86.694339] ata2: hard resetting link [ 87.570903] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 87.571405] ata2.00: configured for UDMA/33 [ 87.581630] ata2: EH complete [ 92.677619] ata2.00: exception Emask 0x10 SAct 0x80 SErr 0x40d0002 action 0xe frozen [ 92.677634] ata2.00: irq_stat 0x00000040, connection status changed [ 92.677639] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 92.677647] ata2.00: failed command: WRITE FPDMA QUEUED [ 92.677651] ata2.00: cmd 61/18:38:88:89:cd/00:00:06:00:00/40 tag 7 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 92.677667] ata2.00: status: { DRDY } [ 92.677675] ata2: hard resetting link [ 93.547571] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 93.548074] ata2.00: configured for UDMA/33 [ 93.558258] ata2: EH complete [ 95.314326] ata2.00: exception Emask 0x10 SAct 0x800000 SErr 0x40d0002 action 0xe frozen [ 95.314340] ata2.00: irq_stat 0x00000040, connection status changed [ 95.314346] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 95.314355] ata2.00: failed command: READ FPDMA QUEUED [ 95.314359] ata2.00: cmd 60/60:b8:f8:73:c2/00:00:0b:00:00/40 tag 23 ncq dma 49152 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 95.314379] ata2.00: status: { DRDY } [ 95.314387] ata2: hard resetting link [ 96.397573] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 96.398071] ata2.00: configured for UDMA/33 [ 96.408278] sd 1:0:0:0: [sda] tag#23 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=1s [ 96.408296] sd 1:0:0:0: [sda] tag#23 Sense Key : Illegal Request [current] [ 96.408303] sd 1:0:0:0: [sda] tag#23 Add. Sense: Unaligned write command [ 96.408309] sd 1:0:0:0: [sda] tag#23 CDB: Read(10) 28 00 0b c2 73 f8 00 00 60 00 [ 96.408313] I/O error, dev sda, sector 197293048 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 96.408341] ata2: EH complete [ 96.730959] ata2.00: exception Emask 0x10 SAct 0x3e SErr 0x40d0002 action 0xe frozen [ 96.730974] ata2.00: irq_stat 0x00000040, connection status changed [ 96.730979] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 96.730987] ata2.00: failed command: WRITE FPDMA QUEUED [ 96.730991] ata2.00: cmd 61/98:08:20:78:de/01:00:0a:00:00/40 tag 1 ncq dma 208896 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 96.731007] ata2.00: status: { DRDY } [ 96.731012] ata2.00: failed command: WRITE FPDMA QUEUED [ 96.731015] ata2.00: cmd 61/08:10:c8:79:de/00:00:0a:00:00/40 tag 2 ncq dma 4096 out res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 96.731028] ata2.00: status: { DRDY } [ 96.731032] ata2.00: failed command: WRITE FPDMA QUEUED [ 96.731035] ata2.00: cmd 61/60:18:e0:79:de/00:00:0a:00:00/40 tag 3 ncq dma 49152 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 96.731048] ata2.00: status: { DRDY } [ 96.731052] ata2.00: failed command: WRITE FPDMA QUEUED [ 96.731055] ata2.00: cmd 61/80:20:48:7a:de/00:00:0a:00:00/40 tag 4 ncq dma 65536 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 96.731067] ata2.00: status: { DRDY } [ 96.731071] ata2.00: failed command: WRITE FPDMA QUEUED [ 96.731074] ata2.00: cmd 61/08:28:10:68:f1/00:00:07:00:00/40 tag 5 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 96.731087] ata2.00: status: { DRDY } [ 96.731093] ata2: hard resetting link [ 97.607572] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 97.608049] ata2.00: configured for UDMA/33 [ 97.618240] ata2: EH complete [ 98.067617] ata2.00: exception Emask 0x10 SAct 0x80000 SErr 0x40d0002 action 0xe frozen [ 98.067633] ata2.00: irq_stat 0x00000040, connection status changed [ 98.067637] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 98.067646] ata2.00: failed command: WRITE FPDMA QUEUED [ 98.067649] ata2.00: cmd 61/18:98:a8:89:cd/00:00:06:00:00/40 tag 19 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 98.067665] ata2.00: status: { DRDY } [ 98.067673] ata2: hard resetting link [ 98.950901] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 98.951378] ata2.00: configured for UDMA/33 [ 98.961572] ata2: EH complete [ 103.770948] ata2.00: exception Emask 0x10 SAct 0x1 SErr 0x40d0002 action 0xe frozen [ 103.770962] ata2.00: irq_stat 0x00000040, connection status changed [ 103.770966] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 103.770974] ata2.00: failed command: WRITE FPDMA QUEUED [ 103.770978] ata2.00: cmd 61/18:00:c8:89:cd/00:00:06:00:00/40 tag 0 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 103.770993] ata2.00: status: { DRDY } [ 103.771001] ata2: hard resetting link [ 104.644223] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 104.644733] ata2.00: configured for UDMA/33 [ 104.654915] ata2: EH complete [ 105.074277] ata2.00: exception Emask 0x10 SAct 0x1000000 SErr 0x40d0002 action 0xe frozen [ 105.074290] ata2.00: irq_stat 0x00000040, connection status changed [ 105.074294] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 105.074302] ata2.00: failed command: READ FPDMA QUEUED [ 105.074305] ata2.00: cmd 60/00:c0:b0:8e:2a/01:00:04:00:00/40 tag 24 ncq dma 131072 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 105.074321] ata2.00: status: { DRDY } [ 105.074327] ata2: hard resetting link [ 105.970888] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 105.971346] ata2.00: configured for UDMA/33 [ 105.981533] sd 1:0:0:0: [sda] tag#24 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s [ 105.981544] sd 1:0:0:0: [sda] tag#24 Sense Key : Illegal Request [current] [ 105.981550] sd 1:0:0:0: [sda] tag#24 Add. Sense: Unaligned write command [ 105.981556] sd 1:0:0:0: [sda] tag#24 CDB: Read(10) 28 00 04 2a 8e b0 00 01 00 00 [ 105.981560] I/O error, dev sda, sector 69897904 op 0x0:(READ) flags 0x80700 phys_seg 31 prio class 0 [ 105.981586] ata2: EH complete [ 106.544280] ata2.00: exception Emask 0x10 SAct 0x400000 SErr 0x40d0002 action 0xe frozen [ 106.544294] ata2.00: irq_stat 0x00000040, connection status changed [ 106.544299] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 106.544307] ata2.00: failed command: WRITE FPDMA QUEUED [ 106.544310] ata2.00: cmd 61/08:b0:48:fb:07/00:00:02:00:00/40 tag 22 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 106.544326] ata2.00: status: { DRDY } [ 106.544333] ata2: hard resetting link [ 107.410951] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 107.411376] ata2.00: configured for UDMA/33 [ 107.421558] ata2: EH complete [ 109.744281] ata2.00: exception Emask 0x10 SAct 0x800000 SErr 0x40d0002 action 0xe frozen [ 109.744294] ata2.00: irq_stat 0x00000040, connection status changed [ 109.744299] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 109.744307] ata2.00: failed command: WRITE FPDMA QUEUED [ 109.744310] ata2.00: cmd 61/18:b8:e8:89:cd/00:00:06:00:00/40 tag 23 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 109.744326] ata2.00: status: { DRDY } [ 109.744333] ata2: hard resetting link [ 110.640888] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 110.641391] ata2.00: configured for UDMA/33 [ 110.651573] ata2: EH complete [ 113.434232] ata2.00: exception Emask 0x10 SAct 0x200 SErr 0x40d0002 action 0xe frozen [ 113.434246] ata2.00: irq_stat 0x00000040, connection status changed [ 113.434250] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 113.434266] ata2.00: failed command: WRITE FPDMA QUEUED [ 113.434268] ata2.00: cmd 61/08:48:00:b8:f1/00:00:07:00:00/40 tag 9 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 113.434280] ata2.00: status: { DRDY } [ 113.434286] ata2: hard resetting link [ 114.330891] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 114.331341] ata2.00: configured for UDMA/33 [ 114.341481] ata2: EH complete [ 115.717609] ata2.00: exception Emask 0x10 SAct 0x2000 SErr 0x40d0002 action 0xe frozen [ 115.717622] ata2.00: irq_stat 0x00000040, connection status changed [ 115.717626] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 115.717634] ata2.00: failed command: WRITE FPDMA QUEUED [ 115.717637] ata2.00: cmd 61/60:68:08:8a:cd/00:00:06:00:00/40 tag 13 ncq dma 49152 out res 40/00:58:00:00:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) [ 115.717653] ata2.00: status: { DRDY } [ 115.717660] ata2: hard resetting link [ 116.614208] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 116.614644] ata2.00: configured for UDMA/33 [ 116.624824] ata2: EH complete [ 117.637624] ata2.00: exception Emask 0x10 SAct 0x7c000007 SErr 0x40d0002 action 0xe frozen [ 117.637637] ata2.00: irq_stat 0x00000040, connection status changed [ 117.637641] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 117.637648] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637651] ata2.00: cmd 61/08:00:c8:78:de/00:00:0a:00:00/40 tag 0 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637667] ata2.00: status: { DRDY } [ 117.637671] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637674] ata2.00: cmd 61/38:08:d8:78:de/00:00:0a:00:00/40 tag 1 ncq dma 28672 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637688] ata2.00: status: { DRDY } [ 117.637692] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637695] ata2.00: cmd 61/10:10:18:79:de/00:00:0a:00:00/40 tag 2 ncq dma 8192 out res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637708] ata2.00: status: { DRDY } [ 117.637712] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637715] ata2.00: cmd 61/08:d0:20:78:de/00:00:0a:00:00/40 tag 26 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637728] ata2.00: status: { DRDY } [ 117.637732] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637735] ata2.00: cmd 61/20:d8:40:78:de/00:00:0a:00:00/40 tag 27 ncq dma 16384 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637747] ata2.00: status: { DRDY } [ 117.637751] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637754] ata2.00: cmd 61/08:e0:70:78:de/00:00:0a:00:00/40 tag 28 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637766] ata2.00: status: { DRDY } [ 117.637771] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637773] ata2.00: cmd 61/08:e8:a8:78:de/00:00:0a:00:00/40 tag 29 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637786] ata2.00: status: { DRDY } [ 117.637790] ata2.00: failed command: WRITE FPDMA QUEUED [ 117.637793] ata2.00: cmd 61/08:f0:b8:78:de/00:00:0a:00:00/40 tag 30 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 117.637805] ata2.00: status: { DRDY } [ 117.637811] ata2: hard resetting link [ 118.534229] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 118.534689] ata2.00: configured for UDMA/33 [ 118.544884] ata2: EH complete [ 121.690945] ata2.00: exception Emask 0x10 SAct 0x400 SErr 0x40d0002 action 0xe frozen [ 121.690959] ata2.00: irq_stat 0x00000040, connection status changed [ 121.690964] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 121.690972] ata2.00: failed command: WRITE FPDMA QUEUED [ 121.690975] ata2.00: cmd 61/18:50:70:8a:cd/00:00:06:00:00/40 tag 10 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 121.690991] ata2.00: status: { DRDY } [ 121.690999] ata2: hard resetting link [ 122.587560] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 122.588014] ata2.00: configured for UDMA/33 [ 122.598196] ata2: EH complete [ 123.824246] ata2.00: exception Emask 0x10 SAct 0x80dc0003 SErr 0x40d0002 action 0xe frozen [ 123.824259] ata2.00: irq_stat 0x00000040, connection status changed [ 123.824263] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch } [ 123.824271] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824274] ata2.00: cmd 61/50:00:f0:78:de/00:00:0a:00:00/40 tag 0 ncq dma 40960 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824290] ata2.00: status: { DRDY } [ 123.824294] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824297] ata2.00: cmd 61/30:08:48:79:de/00:00:0a:00:00/40 tag 1 ncq dma 24576 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824311] ata2.00: status: { DRDY } [ 123.824316] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824319] ata2.00: cmd 61/40:90:20:78:de/00:00:0a:00:00/40 tag 18 ncq dma 32768 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824332] ata2.00: status: { DRDY } [ 123.824336] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824339] ata2.00: cmd 61/08:98:68:78:de/00:00:0a:00:00/40 tag 19 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824352] ata2.00: status: { DRDY } [ 123.824356] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824359] ata2.00: cmd 61/20:a0:88:78:de/00:00:0a:00:00/40 tag 20 ncq dma 16384 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824371] ata2.00: status: { DRDY } [ 123.824375] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824378] ata2.00: cmd 61/18:b0:b0:78:de/00:00:0a:00:00/40 tag 22 ncq dma 12288 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824390] ata2.00: status: { DRDY } [ 123.824394] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824397] ata2.00: cmd 61/08:b8:d0:78:de/00:00:0a:00:00/40 tag 23 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824410] ata2.00: status: { DRDY } [ 123.824414] ata2.00: failed command: WRITE FPDMA QUEUED [ 123.824417] ata2.00: cmd 61/08:f8:e0:78:de/00:00:0a:00:00/40 tag 31 ncq dma 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) [ 123.824429] ata2.00: status: { DRDY } [ 123.824435] ata2: hard resetting link [ 124.720950] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 124.721388] ata2.00: configured for UDMA/33 [ 124.731585] ata2: EH complete