Hi Dmitry,
A. Run our VTNext_ARM64_Release.out – this is doing some FPGA reset and setup of GPIOs
B. sudo media-ctl -d /dev/media0 -l '"msm_csiphy2":1->"msm_csid1":0[1],"msm_csid1":1->"msm_ispif1":0[1],"msm_ispif1":1->"msm_vfe0_rdi1":0[1]'
If #3 does not work for you, then let me know and I will proceed with getting access to our kernel repository.
Thanks,
Kim
From: Jordan Holt <jordan.holt@sightlineapplications.com>
Sent: Wednesday, January 25, 2023 10:20 AM
To: Steve Olson <steve.olson@sightlineapplications.com>; Dmitry Baryshkov <dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com>
Cc: Paul Neuhardt <paul.neuhardt@linaro.org>; sightlineapplications@lists.linaro.org
Subject: RE: [Sightlineapplications] Re: Project Status and Burn Report
I tried to send with a picture, but mail is “being held for review”.
Jordan Holt | CTO
| SightLine Applications Inc. | Onboard Video
Processing |
he/him | 503 724-9727
Please note our NEW PORTLAND ADDRESS is:
5711 S Hood Ave., Suite A
Portland, OR 97239
From: Jordan Holt
Sent: Wednesday, January 25, 2023 10:18 AM
To: Steve Olson <steve.olson@sightlineapplications.com>; Dmitry Baryshkov <dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com>
Cc: Paul Neuhardt <paul.neuhardt@linaro.org>;
sightlineapplications@lists.linaro.org
Subject: RE: [Sightlineapplications] Re: Project Status and Burn Report
This should be the settings. If you can get it to display on your analog TV, click the middle button (press in) then toggle it up/down to get to
System then press in then you want Frame Rate and Freq like below.
Jordan Holt | CTO | SightLine Applications Inc. | Onboard Video Processing | he/him | 503 724-9727
Please note our NEW PORTLAND ADDRESS is:
5711 S Hood Ave., Suite A
Portland, OR 97239
-----Original Message-----
From: Steve Olson <steve.olson@sightlineapplications.com>
Sent: Wednesday, January 25, 2023 10:14 AM
To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com>
Cc: Jordan Holt <jordan.holt@sightlineapplications.com>; Paul Neuhardt <paul.neuhardt@linaro.org>;
sightlineapplications@lists.linaro.org
Subject: RE: [Sightlineapplications] Re: Project Status and Burn Report
Yes, it's just NTSC composite video. I think can configure for PAL too, but to do that you need to be able to see the video to do that.
In parallel, I've started the process of sending you another camera and board.
Steve
Steve Olson | CEO | SightLine Applications Inc. | Onboard Video Processing | he/him
503 975-8478 (mobile) |
www.sightlineapplications.com
-----Original Message-----
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Sent: Wednesday, January 25, 2023 9:50 AM
To: Kim Steiner <kim.steiner@sightlineapplications.com>
Cc: Jordan Holt <jordan.holt@sightlineapplications.com>; Paul Neuhardt <paul.neuhardt@linaro.org>;
sightlineapplications@lists.linaro.org
Subject: [Sightlineapplications] Re: Project Status and Burn Report
On 25/01/2023 19:47, Kim Steiner wrote:
> Hi Dmitry,
>
> One other thought in terms of getting the hd-sdi camera to work is to try the analog out connector. It is the yellow connector on the hd-sdi camera cabling. Would you have a way to display this?
I'll check if I can find a capture device. Is it just a composite video signal or something more intelligent?
>
> Thanks,
> Kim
>
> -----Original Message-----
> From: Kim Steiner
> Sent: Tuesday, January 24, 2023 3:31 PM
> To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> Cc: Jordan Holt <jordan.holt@sightlineapplications.com>; Paul Neuhardt
> <paul.neuhardt@linaro.org>;
sightlineapplications@lists.linaro.org
> Subject: RE: [Sightlineapplications] Re: Project Status and Burn
> Report
>
> Resending with basically no message then this one:
>
> Hi Dmitry,
>
> In regards to our testing, we have seen a GPU fault crash with our custom board (with 5.15 kernel) during temp testing. On one unit, we have seen the GPU fault crash at 118F (47C) while our custom board is sitting on a desk. The
output of the GPU fault crash occurs once and our application continues to run. What do you think of this output?:
>
> [ 156.660355] msm 900000.mdss: CP | opcode error | possible opcode=0x00000000 [ 156.662139] msm 900000.mdss: [drm:a5xx_irq] *ERROR* gpu fault ring 0 fence 5e47 status 800001C1 rb 1820/17e6 ib1 0000000003C1B000/0000 ib2 0000000001483000/0000
[ 156.666297] msm 900000.mdss: [drm:recover_worker] *ERROR* A530: hangcheck recover!
> [ 156.680832] msm 900000.mdss: [drm:recover_worker] *ERROR* A530: offending task: VTNext_ARM:sq0 (./VTNext_ARM64_Release.out -FULL) [ 156.699196] revision: 530 (5.3.0.2) [ 156.699341] msm 900000.mdss: [drm:a5xx_irq] *ERROR* gpu
fault ring 0 fence 5e47 status 800001C1 rb 1820/17e6 ib1 0000000003C1B000/0000 ib2 0000000001483000/0000
> [ 156.699833] rb 0: fence: 24134/24135
> [ 156.717750] rptr: 6081
> [ 156.721300] rb wptr: 6118
> [ 156.724047] rb 1: fence: 0/0
> [ 156.726786] rptr: 0
> [ 156.729795] rb wptr: 0
> [ 156.732207] rb 2: fence: 0/0
> [ 156.734670] rptr: 0
> [ 156.737779] rb wptr: 0
> [ 156.740191] rb 3: fence: 0/0
> [ 156.742649] rptr: 0
> [ 156.745768] rb wptr: 0
> [ 156.748186] CP_SCRATCH_REG0: 0
> [ 156.750641] CP_SCRATCH_REG1: 0
> [ 156.753762] CP_SCRATCH_REG2: 24134
> [ 156.756812] CP_SCRATCH_REG3: 0
> [ 156.760169] CP_SCRATCH_REG4: 0
> [ 156.763222] CP_SCRATCH_REG5: 0
> [ 156.766262] CP_SCRATCH_REG6: 0
> [ 156.769300] CP_SCRATCH_REG7: 0
> [ 156.773675] msm 900000.mdss: [drm:recover_worker] *ERROR* A530: hangcheck recover!
>
> Thanks,
> Kim
--
With best wishes
Dmitry
_______________________________________________
Sightlineapplications mailing list --
sightlineapplications@lists.linaro.org
To unsubscribe send an email to
sightlineapplications-leave@lists.linaro.org