Dear Fathi Boudra,
Is these binary images contains LCD Touch Expansion drivers? We are using the following LCD Touch Panel.
http://www.svtronics.com/products/34-pandaboardes-display-expansion-board
Do we need to connect a PC monitor through HDMI to DVI cable?
Please let me know. We are NOT seeing any display. But power is up as Keyboard and Mouse got the power.
Regards, Srinivas G.
On Thu, Aug 9, 2012 at 1:02 PM, Srinivas Ganji < srinivasganji.android@gmail.com> wrote:
Dear Fathi Boudra,
Thanks for your prompt reply.
I saw all of your e-mails. I am doing again with correct words as you suggested. I think, I was overlook the statements earlier as it was there /dev/sdX only.
I will let you know, once I complete it either it is success / failure / any issues.
Thanks again for your information.
Regards, Srinivas G
On Thu, Aug 9, 2012 at 12:54 PM, Fathi Boudra fathi.boudra@linaro.orgwrote:
On 9 August 2012 10:06, Srinivas Ganji srinivasganji.android@gmail.com wrote:
Dear Fathi Boudra,
Thank you very much for your e-mails with explanations. I will go
through
it, surely. But, I have a basic question. Who will create the
partitions on
SD card? I did not create myself. I thought that your commands only
create.
The dd command will take care of the partitions.
I think, in STEP-3, I need to pass /dev/sdb instead of /dev/sdb1. Is
this
correct?
This is correct. I sent a second mail right after to raise the step 3 issue.
Please let me know about the creation of the partitions in SD card.
Thanks a lot.
Regards, Srinivas G.
On Thu, Aug 9, 2012 at 12:11 PM, Fathi Boudra fathi.boudra@linaro.org wrote:
On 8 August 2012 19:02, Zach Pfeffer zach.pfeffer@linaro.org wrote:
Srinivas,
Please use the instructions on:
https://android-build.linaro.org/builds/~linaro-android/panda-ics-gcc47-tilt...
Those instructions are incomplete. They don't contain the binaries section.
@Srinivas: the instructions on releases.linaro.org are correct. I pointed your mistakes in previous e-mails. Let me know if you need further help.
On 8 August 2012 10:21, Srinivas Ganji <
srinivasganji.android@gmail.com>
wrote:
Hi All,
We have a Pandaboard ES model with us. We purchased the same last
week.
We want to test board with the pre-built images from Linaro. So, we followed the following steps.
The main link is
http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-...
STEPS:
- wget
http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-...
- gunzip panda-ics-gcc47-tilt-stable-blob.img.gz
- sudo dd bs=4M if=panda-ics-gcc47-tilt-stable-blob.img
of=/dev/sdb1
- wget
http://releases.linaro.org/12.07/android/images/panda-ics-gcc47-tilt-stable-...
- chmod a+x install-binaries.sh
- ./install-binaries.sh /dev/sdb1
After doing above steps, we inserted the SD card into the
Pandaboard.
We also connected other peripherals like HDMI cable, USB Mouse, USB Keyboard, Serial cable. The other end (DVI) is connected to the LED monitor. After every thing is connected correctly, we connected the power cable. However, we did not see any thing (display) in the LED monitor as well as
Hyper
terminal.
Are we missing any thing here? Are we followed the correct steps?
Is the step-6 correct? Actually, it looks as follows. $./install-binaries.sh /dev/sdX2 "device node of system partition"
But, I do not understand about "device node of system partition".
Please suggest us.
Regards, Srinivas G
The output of the STEP-6.
vendor/ vendor/imgtec/ vendor/imgtec/panda/ vendor/imgtec/panda/BoardConfigPanda.mk vendor/imgtec/panda/proprietary/ vendor/imgtec/panda/proprietary/libsrv_init.so vendor/imgtec/panda/proprietary/gralloc.omap4.so vendor/imgtec/panda/proprietary/libsrv_um.so vendor/imgtec/panda/proprietary/libIMGegl.so vendor/imgtec/panda/proprietary/libEGL_POWERVR_SGX540_120.so vendor/imgtec/panda/proprietary/libGLESv2_POWERVR_SGX540_120.so vendor/imgtec/panda/proprietary/pvrsrvinit vendor/imgtec/panda/proprietary/libGLESv1_CM_POWERVR_SGX540_120.so vendor/imgtec/panda/proprietary/libusc.so vendor/imgtec/panda/proprietary/libPVRScopeServices.so vendor/imgtec/panda/proprietary/libpvr2d.so vendor/imgtec/panda/proprietary/libglslcompiler.so vendor/imgtec/panda/proprietary/libpvrANDROID_WSEGL.so vendor/imgtec/panda/device-panda.mk vendor/ti/ vendor/ti/panda/ vendor/ti/panda/BoardConfigVendor.mk vendor/ti/panda/device-vendor.mk
Files extracted successfully. mount: you must specify the filesystem type cp: cannot create regular file `/mnt/bin/pvrsrvinit': No such file
or
directory cp: cannot create regular file `/mnt/vendor/lib/hw/gralloc.omap4.so
':
No such file or directory umount2: Invalid argument umount: /dev/sdb1: not mounted /home/pandriod/Android Success, installing binary files
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
-- Zach Pfeffer Android Platform Team Lead, Linaro Platform Teams Linaro.org | Open source software for ARM SoCs Follow Linaro: http://www.facebook.com/pages/Linaro http://twitter.com/#%21/linaroorg - http://www.linaro.org/linaro-blog
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
-- Fathi Boudra Linaro Release Manager | Validation Project Manager Linaro.org | Open source software for ARM SoCs
-- Fathi Boudra Linaro Release Manager | Validation Project Manager Linaro.org | Open source software for ARM SoCs