Mathieu,
I've got:
Xloader version: u8500-android-2.3_v2.8 Built: Thu Jun 30 07:08:07 PM 2011 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to do AVS calculations About to exec MEMINIT function 0 Executed MEMINIT function 0 About to ask ISSW to perform MEMINIT ISSW returned from MEMINIT, Vendor ID 0xFF len 0x10 CS0 density 0x54 CS1 density 0x54 About to exec MEMINIT function 1
SoC settings: INFO: @(#)SOC-SETTINGS v3.0.2-AVS_VMOD_workaround db8500 v2 1000Mh z Jun 30 2011 19:08:06 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Error setting 1GHz dvfs: 0x00000000 Executed MEMINIT function 1 MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader TEEC_InvokeCommand TEEC_SUCCESS != result (0xFFFF000F) Loading raw payload XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 U8500 $
Do I need to flash the new uboot as specified by these instructions:
http://www.igloocommunity.org/support/Flashing_howto
If so the instructions have at 2 holes that I've found:
It says,
Due to differences in default U-Boot environment, these instructions will not work if you have flashed the Igloo Community Android Gingerbread releases, please flash the latest Ubuntu image to get a compatible U-Boot.
What if I've got some random Snowball? Shouldn't we list a particular uboot version to look for?
Also, the instructions have me go here:
http://www.igloocommunity.org/support/Index.php/Downloads
Which doesn't list an Ubuntu build.
can we make these better?
On 12-06-19 01:31 PM, Zach Pfeffer wrote:
Mathieu,
I've got:
Xloader version: u8500-android-2.3_v2.8 Built: Thu Jun 30 07:08:07 PM 2011 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to do AVS calculations About to exec MEMINIT function 0 Executed MEMINIT function 0 About to ask ISSW to perform MEMINIT ISSW returned from MEMINIT, Vendor ID 0xFF len 0x10 CS0 density 0x54 CS1 density 0x54 About to exec MEMINIT function 1
SoC settings: INFO: @(#)SOC-SETTINGS v3.0.2-AVS_VMOD_workaround db8500 v2 1000Mh z Jun 30 2011 19:08:06 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Error setting 1GHz dvfs: 0x00000000 Executed MEMINIT function 1 MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader TEEC_InvokeCommand TEEC_SUCCESS != result (0xFFFF000F) Loading raw payload XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 U8500 $
You definitely need to upgrade your uboot.
Do I need to flash the new uboot as specified by these instructions:
http://www.igloocommunity.org/support/Flashing_howto
If so the instructions have at 2 holes that I've found:
It says,
Due to differences in default U-Boot environment, these instructions will not work if you have flashed the Igloo Community Android Gingerbread releases, please flash the latest Ubuntu image to get a compatible U-Boot.
The GB release is STE specific and as such has its own way of packaging and working.
What if I've got some random Snowball? Shouldn't we list a particular uboot version to look for?
All snowball have been shipped with a very old snapshot of uboot and guaranteed to fail with the new lamc/lmc. It is mandatory to upgrade.
Also, the instructions have me go here:
http://www.igloocommunity.org/support/Index.php/Downloads
Which doesn't list an Ubuntu build.
All our builds are listed under "Linux BSP releases page."
can we make these better?
On 19 June 2012 15:01, Mathieu Poirier mathieu.poirier@linaro.org wrote:
On 12-06-19 01:31 PM, Zach Pfeffer wrote:
Mathieu,
I've got:
Xloader version: u8500-android-2.3_v2.8 Built: Thu Jun 30 07:08:07 PM 2011 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to do AVS calculations About to exec MEMINIT function 0 Executed MEMINIT function 0 About to ask ISSW to perform MEMINIT ISSW returned from MEMINIT, Vendor ID 0xFF len 0x10 CS0 density 0x54 CS1 density 0x54 About to exec MEMINIT function 1
SoC settings: INFO: @(#)SOC-SETTINGS v3.0.2-AVS_VMOD_workaround db8500 v2 1000Mh z Jun 30 2011 19:08:06 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Error setting 1GHz dvfs: 0x00000000 Executed MEMINIT function 1 MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader TEEC_InvokeCommand TEEC_SUCCESS != result (0xFFFF000F) Loading raw payload XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 U8500 $
You definitely need to upgrade your uboot.
Do I need to flash the new uboot as specified by these instructions:
http://www.igloocommunity.org/support/Flashing_howto
If so the instructions have at 2 holes that I've found:
It says,
Due to differences in default U-Boot environment, these instructions will not work if you have flashed the Igloo Community Android Gingerbread releases, please flash the latest Ubuntu image to get a compatible U-Boot.
The GB release is STE specific and as such has its own way of packaging and working.
What if I've got some random Snowball? Shouldn't we list a particular uboot version to look for?
All snowball have been shipped with a very old snapshot of uboot and guaranteed to fail with the new lamc/lmc. It is mandatory to upgrade.
Also, the instructions have me go here:
http://www.igloocommunity.org/support/Index.php/Downloads
Which doesn't list an Ubuntu build.
All our builds are listed under "Linux BSP releases page."
Okay. Would you mind running through the instructions and generating a better, more conscience set, maybe with all the commands laid out? I'll then run through what you've done to verify.
can we make these better?
On 12-06-19 02:03 PM, Zach Pfeffer wrote:
On 19 June 2012 15:01, Mathieu Poirier mathieu.poirier@linaro.org wrote:
On 12-06-19 01:31 PM, Zach Pfeffer wrote:
Mathieu,
I've got:
Xloader version: u8500-android-2.3_v2.8 Built: Thu Jun 30 07:08:07 PM 2011 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to do AVS calculations About to exec MEMINIT function 0 Executed MEMINIT function 0 About to ask ISSW to perform MEMINIT ISSW returned from MEMINIT, Vendor ID 0xFF len 0x10 CS0 density 0x54 CS1 density 0x54 About to exec MEMINIT function 1
SoC settings: INFO: @(#)SOC-SETTINGS v3.0.2-AVS_VMOD_workaround db8500 v2 1000Mh z Jun 30 2011 19:08:06 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Error setting 1GHz dvfs: 0x00000000 Executed MEMINIT function 1 MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader TEEC_InvokeCommand TEEC_SUCCESS != result (0xFFFF000F) Loading raw payload XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 U8500 $
You definitely need to upgrade your uboot.
Do I need to flash the new uboot as specified by these instructions:
http://www.igloocommunity.org/support/Flashing_howto
If so the instructions have at 2 holes that I've found:
It says,
Due to differences in default U-Boot environment, these instructions will not work if you have flashed the Igloo Community Android Gingerbread releases, please flash the latest Ubuntu image to get a compatible U-Boot.
The GB release is STE specific and as such has its own way of packaging and working.
What if I've got some random Snowball? Shouldn't we list a particular uboot version to look for?
All snowball have been shipped with a very old snapshot of uboot and guaranteed to fail with the new lamc/lmc. It is mandatory to upgrade.
Also, the instructions have me go here:
http://www.igloocommunity.org/support/Index.php/Downloads
Which doesn't list an Ubuntu build.
All our builds are listed under "Linux BSP releases page."
Okay. Would you mind running through the instructions and generating a better, more conscience set, maybe with all the commands laid out? I'll then run through what you've done to verify.
Steps to upgrade ICS on emmc are here:
http://igloocommunity.org/support/Android_Getting_started_with_ICS#Boot_ICS_...
Using the 12.05 ubuntu release, the command to generate a Ubuntu riff'able image can be found at the bottom of this page:
http://igloocommunity.org/support/BSP_Quick_Start
I have used both methods successfully with the 12.05 release.
can we make these better?
On 19 June 2012 15:24, Mathieu Poirier mathieu.poirier@linaro.org wrote:
On 12-06-19 02:03 PM, Zach Pfeffer wrote:
On 19 June 2012 15:01, Mathieu Poirier mathieu.poirier@linaro.org wrote:
On 12-06-19 01:31 PM, Zach Pfeffer wrote:
Mathieu,
I've got:
Xloader version: u8500-android-2.3_v2.8 Built: Thu Jun 30 07:08:07 PM 2011 Configured for: 8500 B0 Running on chip ID: 8500B2 SECURITY_Init Boot scenario: NORMAL USB - Enabled: 0x00000001 Enum done: 0x00000000 Last reset reason: POWER_ON_RESET XP70_DATA_MBFFC: 0xFF000001 PWR_MNGT_STARTED 1 About to do AVS calculations About to exec MEMINIT function 0 Executed MEMINIT function 0 About to ask ISSW to perform MEMINIT ISSW returned from MEMINIT, Vendor ID 0xFF len 0x10 CS0 density 0x54 CS1 density 0x54 About to exec MEMINIT function 1
SoC settings: INFO: @(#)SOC-SETTINGS v3.0.2-AVS_VMOD_workaround db8500 v2 1000Mh z Jun 30 2011 19:08:06 SoC settings: INFO: Memory size=0x40000000 (1024 MB) SoC settings: INFO: DDR Test Ended successfully. SoC settings: INFO: Requesting 1GHz from PRCMU SoC settings: INFO: Error setting 1GHz dvfs: 0x00000000 Executed MEMINIT function 1 MEMINIT passed OK About to load NORMAL After NORMAL loaded verify_signedheader TEEC_InvokeCommand TEEC_SUCCESS != result (0xFFFF000F) Loading raw payload XL_DisableCachesMmu Before ENABLE_L2CC After ENABLE_L2CC Flush boot issw code Before call normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 0 U8500 $
You definitely need to upgrade your uboot.
Do I need to flash the new uboot as specified by these instructions:
http://www.igloocommunity.org/support/Flashing_howto
If so the instructions have at 2 holes that I've found:
It says,
Due to differences in default U-Boot environment, these instructions will not work if you have flashed the Igloo Community Android Gingerbread releases, please flash the latest Ubuntu image to get a compatible U-Boot.
The GB release is STE specific and as such has its own way of packaging and working.
What if I've got some random Snowball? Shouldn't we list a particular uboot version to look for?
All snowball have been shipped with a very old snapshot of uboot and guaranteed to fail with the new lamc/lmc. It is mandatory to upgrade.
Also, the instructions have me go here:
http://www.igloocommunity.org/support/Index.php/Downloads
Which doesn't list an Ubuntu build.
All our builds are listed under "Linux BSP releases page."
Okay. Would you mind running through the instructions and generating a better, more conscience set, maybe with all the commands laid out? I'll then run through what you've done to verify.
Steps to upgrade ICS on emmc are here:
http://igloocommunity.org/support/Android_Getting_started_with_ICS#Boot_ICS_...
Using the 12.05 ubuntu release, the command to generate a Ubuntu riff'able image can be found at the bottom of this page:
http://igloocommunity.org/support/BSP_Quick_Start
I have used both methods successfully with the 12.05 release.
Okay, here's what I'm still unclear on. When users boot up their unit how do they know that they need to upgrade. And on both pages:
http://igloocommunity.org/support/Android_Getting_started_with_ICS#Boot_ICS_...
and
http://igloocommunity.org/support/BSP_Quick_Start
Which steps should people follow exactly?
can we make these better?
linaro-android@lists.linaro.org
-
Mathieu Poirier -
Zach Pfeffer