Help-
I have a new Panda board (the box label says UEVM4460G-02-01-00) with a 16 GB SD card and DVI monitor, with Ubuntu 10.04 as the dev platform.
I have been trying a number of different pre-built Android binaries (starting at pandaboard.org and following instructions there (Quickstart with pre-built binaries) which takes me to omappedia and linaro, but can't seem to get any to come to full running status.
The release with most success is 12.03, but as soon as the "Android" shimmer screen is replaced with the Android environment, a window pops up to say "Unfortunately, Launcher has stopped". Some green blocks are moving about the screen at approx a one second interval, and moving the mouse causes the cursor to move very slowly, in sync with the green block movements.
A few icons are shown at bottom left, and time of day is shown at bottom right. Nothing else is visible on the screen.
Pressing the reset button cause a reboot, but this time it gets no further than the Android shimmer screen. The TTY console shows what appears to be an endless loop of a few dozen events, all seeming to repeat themselves.
Not sure what details are needed to get past this problem, any help would be most appreciated.
I have also tried releases 12.01, 12.02, and 11.11. None of these even show anything on the monitor.
Thanks, Ron
____________________________________________________________ 53 Year Old Mom Looks 33 The Stunning Results of Her Wrinkle Trick Has Botox Doctors Worried http://thirdpartyoffers.juno.com/TGL3131/4f94bdbf27e2681f827st01vuc
Hi Ron,
Can only say from experience that i checked build 11.11/11.12/12.03 on Pandaboard using HDMI monitor and it works. Only problem occurs when it enters 'sleep' mode. Maybe if you post some logging from the console you can expect more help. Did you try another SD card? I did see some stability differences between SD cards (I use a 2 GB card). Best regards,
Ruud
-----Original Message----- From: linaro-android-bounces@lists.linaro.org [mailto:linaro-android-bounces@lists.linaro.org] On Behalf Of rknollman@juno.com Sent: maandag 23 april 2012 4:26 To: linaro-android@lists.linaro.org Subject: Linaro on Panda Board
Help-
I have a new Panda board (the box label says UEVM4460G-02-01-00) with a 16 GB SD card and DVI monitor, with Ubuntu 10.04 as the dev platform.
I have been trying a number of different pre-built Android binaries (starting at pandaboard.org and following instructions there (Quickstart with pre-built binaries) which takes me to omappedia and linaro, but can't seem to get any to come to full running status.
The release with most success is 12.03, but as soon as the "Android" shimmer screen is replaced with the Android environment, a window pops up to say "Unfortunately, Launcher has stopped". Some green blocks are moving about the screen at approx a one second interval, and moving the mouse causes the cursor to move very slowly, in sync with the green block movements.
A few icons are shown at bottom left, and time of day is shown at bottom right. Nothing else is visible on the screen.
Pressing the reset button cause a reboot, but this time it gets no further than the Android shimmer screen. The TTY console shows what appears to be an endless loop of a few dozen events, all seeming to repeat themselves.
Not sure what details are needed to get past this problem, any help would be most appreciated.
I have also tried releases 12.01, 12.02, and 11.11. None of these even show anything on the monitor.
Thanks, Ron
____________________________________________________________ 53 Year Old Mom Looks 33 The Stunning Results of Her Wrinkle Trick Has Botox Doctors Worried http://thirdpartyoffers.juno.com/TGL3131/4f94bdbf27e2681f827st01vuc
_______________________________________________ linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
----- Geen virus gevonden in dit bericht. Gecontroleerd door AVG - www.avg.com Versie: 2012.0.1913 / Virusdatabase: 2411/4954 - datum van uitgifte: 04/23/12
Hi Ron,
I think I also experience the same "Unfortunately, Launcher has stopped" a while ago. It might be worth trying to build boot binary by yourself since I do not see the error message when I make boot image by myself.
Download boot.tar.bz2,system.tar.bz2 and userdata.tar.bz2 from https://android-build.linaro.org/builds/~linaro-android/panda-ics-gcc46-tilt... and please follow the instructions of "How to Use Prebuilt Images".
Regards,
Akira
On 04/23/2012 11:25 AM, rknollman@juno.com wrote:
Help-
I have a new Panda board (the box label says UEVM4460G-02-01-00) with a 16 GB SD card and DVI monitor, with Ubuntu 10.04 as the dev platform.
I have been trying a number of different pre-built Android binaries (starting at pandaboard.org and following instructions there (Quickstart with pre-built binaries) which takes me to omappedia and linaro, but can't seem to get any to come to full running status.
The release with most success is 12.03, but as soon as the "Android" shimmer screen is replaced with the Android environment, a window pops up to say "Unfortunately, Launcher has stopped". Some green blocks are moving about the screen at approx a one second interval, and moving the mouse causes the cursor to move very slowly, in sync with the green block movements.
A few icons are shown at bottom left, and time of day is shown at bottom right. Nothing else is visible on the screen.
Pressing the reset button cause a reboot, but this time it gets no further than the Android shimmer screen. The TTY console shows what appears to be an endless loop of a few dozen events, all seeming to repeat themselves.
Not sure what details are needed to get past this problem, any help would be most appreciated.
I have also tried releases 12.01, 12.02, and 11.11. None of these even show anything on the monitor.
Thanks, Ron
53 Year Old Mom Looks 33 The Stunning Results of Her Wrinkle Trick Has Botox Doctors Worried http://thirdpartyoffers.juno.com/TGL3131/4f94bdbf27e2681f827st01vuc
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
On 04/25/2012 04:07 AM, Akira Tsukamoto wrote:
I think I also experience the same "Unfortunately, Launcher has stopped" a while ago. It might be worth trying to build boot binary by yourself since I do not see the error message when I make boot image by myself.
Download boot.tar.bz2,system.tar.bz2 and userdata.tar.bz2 from https://android-build.linaro.org/builds/~linaro-android/panda-ics-gcc46-tilt...
and please follow the instructions of "How to Use Prebuilt Images".
NOTE: the most common cause for this problem is forgetting these steps:
wget http://people.linaro.org/~vishalbhoj/install-binaries-4.0.3.sh chmod a+x install-binaries-4.0.3.sh ./install-binaries-4.0.3.sh /dev/sdc2 #device node of system part
linaro-android@lists.linaro.org
-
Akira Tsukamoto -
Andy Doan -
rknollmanīŧ juno.com -
Ruud Siebierski