Okay, so I have tried both 12.02 for Android and 12.02 for Ubuntu Desktop both for the Origen board.
I got the Android image from here: http://releases.linaro.org/12.02/android/leb-origen/origen-ics-gcc46-sam sunglt-stable-blob.img.gz and the Ubuntu from here: http://releases.linaro.org/12.02/oneiric/ubuntu-desktop/origen-ubuntu-de sktop.img.gz.
My commands to make the Ubuntu image were:
SDCARD=/dev/sdb
IMGFILE=origen-ubuntu-desktop.image
gunzip ${IMGFILE}.gz
dd bs=64k if=${IMGFILE} of=${SDCARD}
I then powered up the Origen board and again, got no output on the LCD and only a small amount of boot information in terminal before the SD card power LED (LED4) went off.
U-Boot 2011.12 (Feb 16 2012 - 21:52:47) for ORIGEN
CPU: S5PC210@1000MHz
Board: ORIGEN
DRAM: 1 GiB
WARNING: Caches not enabled
MMC: SAMSUNG SD/MMC: 0
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
reading uImage
4082320 bytes read
reading uInitrd
2175126 bytes read
## Booting kernel from Legacy Image at 40007000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4082256 Bytes = 3.9 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 42000000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 2175062 Bytes = 2.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
For the Android image, I used the following commands:
SDCARD=/dev/sdb
IMGFILE=origen-ics-gcc46-samsunglt-stable-blob.img
gunzip ${IMGFILE}.gz
dd bs=64k if=${IMGFILE} of=${SDCARD}
Exactly the same thing happened as I previously mentioned, got a bunch of boot text then LED4 goes off and nothing else happens.
Any advice would be gratefully accepted.
Andy
Hi, could you paste your command to flash SD card here?
I have just purchased an Origen Board - Full Package. I flashed the SD card with igen-ics-gcc46-samsunglt-stable-blob.img and placed it into the SD card slot. I flicked the power switch and pressed SWITCH then POWER and saw the board booting in terminal. However, after a short period of time LED4 turns off and I do not see the LCD light or show the Android screen. The output in terminal is given below. Is my board faulty or have I not flashed the correct image to the SD card ?
U-Boot 2011.06-01275-gd6186aa (Feb 17 2012 - 08:54:12) for ORIGEN
CPU: S5PC210@1000MHz
Board: ORIGEN DRAM: 1 GiB WARNING: Caches not enabled MMC: SAMSUNG SD/MMC: 0 *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 reading boot.scr
397 bytes read Running bootscript from mmc0:2 ... ## Executing script at 42000000 reading uImage
4049424 bytes read reading uInitrd
166156 bytes read ## Booting kernel from Legacy Image at 40007000 ... Image Name: Linux-3.0.4+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4049360 Bytes = 3.9 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Android Ramdisk Image Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 166092 Bytes = 162.2 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel. <5>Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <5>Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). <3>CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 <3>CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 <3>CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 <3>CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 <3>CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 <3>CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 <3>CMA reserve : common, addr is 0x57c00000, size is 0x4000000 <3>CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) <7>exynos4_init_clocks: initializing clocks <6>S3C24XX Clocks, Copyright 2004 Simtec Electronics <3>s3c_register_clksrc: clock armclk has no registers set <3>mout_audss: bad source 0 <7>exynos4_setup_clocks: registering clocks <7>exynos4_setup_clocks: xtal is 24000000 <6>EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000<6>EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>sclk_pwm: source is ext_xtal (0), rate is 24000000 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_cam0: source is xusbxti (1), rate is 0 <6>sclk_cam1: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_mixer: source is sclk_dac (0), rate is 24000000 <6>sclk_fimd0: source is xusbxti (1), rate is 0 <6>sclk_fimd1: source is xusbxti (1), rate is 0 <6>sclk_sata: source is mout_mpll (0), rate is 133333333 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_spi: source is mout_mpll (6), rate is 80000000 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 <7>On node 0 totalpages: 188416 <7> Normal zone: 1472 pages used for memmap <7> Normal zone: 0 pages reserved <7> Normal zone: 186944 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 <7>pcpu-alloc: s6528 r8192 d13952 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 <5>Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2
<6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 736MB = 736MB total <5>Memory: 601736k/601736k available, 151928k reserved, 0K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) <6>Preemptible hierarchical RCU implementation. <6>NR_IRQS:624 <6>sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms <6>Console: colour dummy device 80x30 <6>console [tty0] enabled Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 CMA reserve : common, addr is 0x57c00000, size is 0x4000000 CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) S3C24XX Clocks, Copyright 2004 Simtec Electronics s3c_register_clksrc: clock armclk has no registers set mout_audss: bad source 0 EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000 EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 sclk_pwm: source is ext_xtal (0), rate is 24000000 sclk_csis: source is xusbxti (1), rate is 0 sclk_csis: source is xusbxti (1), rate is 0 sclk_cam0: source is xusbxti (1), rate is 0 sclk_cam1: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_mixer: source is sclk_dac (0), rate is 24000000 sclk_fimd0: source is xusbxti (1), rate is 0 sclk_fimd1: source is xusbxti (1), rate is 0 sclk_sata: source is mout_mpll (0), rate is 133333333 sclk_spi: source is xusbxti (1), rate is 0 sclk_spi: source is mout_mpll (6), rate is 80000000 sclk_spi: source is xusbxti (1), rate is 0 sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2
PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 736MB = 736MB total Memory: 601736k/601736k available, 151928k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) Preemptible hierarchical RCU implementation. NR_IRQS:624 sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms Console: colour dummy device 80x30 console <tty0] enabled 6>console [ttySAC2] enabled console [tt<SAC2] enabled 6>Calibrating delay loop... Calibrating delay loop... <c>1992.29 BogoMIPS (lpj=4980736) 1992.29 BogoMIPS<(lpj=4980736) 6>pid_max: default: 32768 minimum: 301 pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: CPU: Testing write buffer coherency: ok ok <6>ftrace: allocating 19856 entries in 59 pages ftrace: allocating 19856 entries in 59 pages <6>CPU0: thread -1, cpu 0, socket 9, mpidr 80000900 CPU0: thread -1, cpu 0, socket 9, <pidr 80000900 6>Calibrating local timer... Calibrating local timer... 249.93MHz. 249.93MHz. <6>hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available <6>L310 cache controller enabled L310 cache cont<oller enabled 6>l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B CPU1: Booted secondary processor <2>CPU1: Unknown IPI message 0x1
_______________________________________________ linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
Hey, Andy
Here we use linaro-android-media-create to burn the sd card. Since I never use the burn steps as you mentioned, so I could not comment on it.
-jack
On 20 March 2012 06:56, Andrew Fraser afraser@andyfraser.co.uk wrote:
Okay, so I have tried both 12.02 for Android and 12.02 for Ubuntu Desktop both for the Origen board.****
I got the Android image from here: http://releases.linaro.org/12.02/android/leb-origen/origen-ics-gcc46-samsung... the Ubuntu from here: http://releases.linaro.org/12.02/oneiric/ubuntu-desktop/origen-ubuntu-deskto... .****
My commands to make the Ubuntu image were:****
SDCARD=/dev/sdb****
IMGFILE=origen-ubuntu-desktop.image****
gunzip ${IMGFILE}.gz****
dd bs=64k if=${IMGFILE} of=${SDCARD}****
I then powered up the Origen board and again, got no output on the LCD and only a small amount of boot information in terminal before the SD card power LED (LED4) went off.****
U-Boot 2011.12 (Feb 16 2012 - 21:52:47) for ORIGEN****
CPU: S5PC210@1000MHz****
Board: ORIGEN****
DRAM: 1 GiB****
WARNING: Caches not enabled****
MMC: SAMSUNG SD/MMC: 0****
In: serial****
Out: serial****
Err: serial****
Hit any key to stop autoboot: 0****
reading uImage****
4082320 bytes read****
reading uInitrd****
2175126 bytes read****
## Booting kernel from Legacy Image at 40007000 ...****
Image Name: Linux****
Image Type: ARM Linux Kernel Image (uncompressed)****
Data Size: 4082256 Bytes = 3.9 MiB****
Load Address: 40008000****
Entry Point: 40008000****
Verifying Checksum ... OK****
## Loading init Ramdisk from Legacy Image at 42000000 ...****
Image Name: initramfs****
Image Type: ARM Linux RAMDisk Image (uncompressed)****
Data Size: 2175062 Bytes = 2.1 MiB****
Load Address: 00000000****
Entry Point: 00000000****
Verifying Checksum ... OK****
Loading Kernel Image ... OK****
OK****
Starting kernel ...****
Uncompressing Linux... done, booting the kernel.****
For the Android image, I used the following commands:****
SDCARD=/dev/sdb****
IMGFILE=origen-ics-gcc46-samsunglt-stable-blob.img****
gunzip ${IMGFILE}.gz****
dd bs=64k if=${IMGFILE} of=${SDCARD}****
Exactly the same thing happened as I previously mentioned, got a bunch of boot text then LED4 goes off and nothing else happens.****
Any advice would be gratefully accepted.****
*Andy***
Hi, could you paste your command to flash SD card here?****
I have just purchased an Origen Board - Full Package. I flashed the SD card with igen-ics-gcc46-samsunglt-stable-blob.img and placed it into the SD card slot. I flicked the power switch and pressed SWITCH then POWER and saw the board booting in terminal. However, after a short period of time LED4 turns off and I do not see the LCD light or show the Android screen. The output in terminal is given below. Is my board faulty or have I not flashed the correct image to the SD card ?****
U-Boot 2011.06-01275-gd6186aa (Feb 17 2012 - 08:54:12) for ORIGEN****
CPU: S5PC210@1000MHz****
Board: ORIGEN DRAM: 1 GiB WARNING: Caches not enabled MMC: SAMSUNG SD/MMC: 0 *** Warning - bad CRC, using default environment****
In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 reading boot.scr****
397 bytes read Running bootscript from mmc0:2 ... ## Executing script at 42000000 reading uImage****
4049424 bytes read reading uInitrd****
166156 bytes read ## Booting kernel from Legacy Image at 40007000 ... Image Name: Linux-3.0.4+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4049360 Bytes = 3.9 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Android Ramdisk Image Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 166092 Bytes = 162.2 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK****
Starting kernel ...****
Uncompressing Linux... done, booting the kernel. <5>Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <5>Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). <3>CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 <3>CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 <3>CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 <3>CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 <3>CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 <3>CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 <3>CMA reserve : common, addr is 0x57c00000, size is 0x4000000 <3>CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) <7>exynos4_init_clocks: initializing clocks <6>S3C24XX Clocks, Copyright 2004 Simtec Electronics <3>s3c_register_clksrc: clock armclk has no registers set <3>mout_audss: bad source 0 <7>exynos4_setup_clocks: registering clocks <7>exynos4_setup_clocks: xtal is 24000000 <6>EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000<6>EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>sclk_pwm: source is ext_xtal (0), rate is 24000000 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_cam0: source is xusbxti (1), rate is 0 <6>sclk_cam1: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_mixer: source is sclk_dac (0), rate is 24000000 <6>sclk_fimd0: source is xusbxti (1), rate is 0 <6>sclk_fimd1: source is xusbxti (1), rate is 0 <6>sclk_sata: source is mout_mpll (0), rate is 133333333 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_spi: source is mout_mpll (6), rate is 80000000 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 <7>On node 0 totalpages: 188416 <7> Normal zone: 1472 pages used for memmap <7> Normal zone: 0 pages reserved <7> Normal zone: 186944 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 <7>pcpu-alloc: s6528 r8192 d13952 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 <5>Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2
<6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 736MB = 736MB total <5>Memory: 601736k/601736k available, 151928k reserved, 0K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) <6>Preemptible hierarchical RCU implementation. <6>NR_IRQS:624 <6>sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms <6>Console: colour dummy device 80x30 <6>console [tty0] enabled Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 CMA reserve : common, addr is 0x57c00000, size is 0x4000000 CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) S3C24XX Clocks, Copyright 2004 Simtec Electronics s3c_register_clksrc: clock armclk has no registers set mout_audss: bad source 0 EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000 EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 sclk_pwm: source is ext_xtal (0), rate is 24000000 sclk_csis: source is xusbxti (1), rate is 0 sclk_csis: source is xusbxti (1), rate is 0 sclk_cam0: source is xusbxti (1), rate is 0 sclk_cam1: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_mixer: source is sclk_dac (0), rate is 24000000 sclk_fimd0: source is xusbxti (1), rate is 0 sclk_fimd1: source is xusbxti (1), rate is 0 sclk_sata: source is mout_mpll (0), rate is 133333333 sclk_spi: source is xusbxti (1), rate is 0 sclk_spi: source is mout_mpll (6), rate is 80000000 sclk_spi: source is xusbxti (1), rate is 0 sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2
PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 736MB = 736MB total Memory: 601736k/601736k available, 151928k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) Preemptible hierarchical RCU implementation. NR_IRQS:624 sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms Console: colour dummy device 80x30 console <tty0] enabled 6>console [ttySAC2] enabled console [tt<SAC2] enabled 6>Calibrating delay loop... Calibrating delay loop... <c>1992.29 BogoMIPS (lpj=4980736) 1992.29 BogoMIPS<(lpj=4980736) 6>pid_max: default: 32768 minimum: 301 pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: CPU: Testing write buffer coherency: ok ok <6>ftrace: allocating 19856 entries in 59 pages ftrace: allocating 19856 entries in 59 pages <6>CPU0: thread -1, cpu 0, socket 9, mpidr 80000900 CPU0: thread -1, cpu 0, socket 9, <pidr 80000900 6>Calibrating local timer... Calibrating local timer... 249.93MHz. 249.93MHz. <6>hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available <6>L310 cache controller enabled L310 cache cont<oller enabled 6>l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B CPU1: Booted secondary processor <2>CPU1: Unknown IPI message 0x1****
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android****
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
Hi Andrew,
I completely had the same issue with you and was able to solve it by making the boot image with modified following way. (I should have seen this email earlier, yesterday was Japanese public holiday ;) )
1) Download these files: boot.tar.bz2 userdata.tar.bz2 system.tar.bz2 from:
https://android-build.linaro.org/builds/~linaro-android/origen-ics-gcc46-sam...
2) Get the latest linaro-image-tools: $bzr branch lp:linaro-image-tools
If you do not have bzr in your ubuntu, then just: $sudo apt-get install bzr should do.
3) Create boot image as following command line: $./linaro-image-tools/linaro-android-media-create --mmc /dev/mmcblk0 --dev origen --system system.tar.bz2 --userdata userdata.tar.bz2 --boot boot.tar.bz2 --extra-boot-args s5p_tvout_fb.hdmi_lcd_display=1 (My PC has SD slot at /dev/mmcblk0 but change it if it is different for you)
4) Insert the SD card to Origen then boot it. The Android will show with 1024x600 resolution in the middle of your display.
Please let me know if this helps.
Thanks,
Akira
On 03/21/2012 12:17 PM, Chenglie He wrote:
Hey, Andy
Here we use linaro-android-media-create to burn the sd card. Since I never use the burn steps as you mentioned, so I could not comment on it.
-jack
On 20 March 2012 06:56, Andrew Fraser <afraser@andyfraser.co.uk mailto:afraser@andyfraser.co.uk> wrote:
Okay, so I have tried both 12.02 for Android and 12.02 for Ubuntu Desktop both for the Origen board.____ I got the Android image from here: http://releases.linaro.org/12.02/android/leb-origen/origen-ics-gcc46-samsunglt-stable-blob.img.gz and the Ubuntu from here: http://releases.linaro.org/12.02/oneiric/ubuntu-desktop/origen-ubuntu-desktop.img.gz.____ __ __ My commands to make the Ubuntu image were:____ __ __ SDCARD=/dev/sdb____ IMGFILE=origen-ubuntu-desktop.image____ gunzip ${IMGFILE}.gz____ dd bs=64k if=${IMGFILE} of=${SDCARD}____ __ __ I then powered up the Origen board and again, got no output on the LCD and only a small amount of boot information in terminal before the SD card power LED (LED4) went off.____ __ __ U-Boot 2011.12 (Feb 16 2012 - 21:52:47) for ORIGEN____ __ __ CPU: S5PC210@1000MHz____ __ __ Board: ORIGEN____ DRAM: 1 GiB____ WARNING: Caches not enabled____ MMC: SAMSUNG SD/MMC: 0____ In: serial____ Out: serial____ Err: serial____ Hit any key to stop autoboot: 0____ reading uImage____ __ __ 4082320 bytes read____ reading uInitrd____ __ __ 2175126 bytes read____ ## Booting kernel from Legacy Image at 40007000 ...____ Image Name: Linux____ Image Type: ARM Linux Kernel Image (uncompressed)____ Data Size: 4082256 Bytes = 3.9 MiB____ Load Address: 40008000____ Entry Point: 40008000____ Verifying Checksum ... OK____ ## Loading init Ramdisk from Legacy Image at 42000000 ...____ Image Name: initramfs____ Image Type: ARM Linux RAMDisk Image (uncompressed)____ Data Size: 2175062 Bytes = 2.1 MiB____ Load Address: 00000000____ Entry Point: 00000000____ Verifying Checksum ... OK____ Loading Kernel Image ... OK____ OK____ __ __ Starting kernel ...____ __ __ Uncompressing Linux... done, booting the kernel.____ __ __ __ __ For the Android image, I used the following commands:____ __ __ SDCARD=/dev/sdb____ IMGFILE=origen-ics-gcc46-samsunglt-stable-blob.img____ gunzip ${IMGFILE}.gz____ dd bs=64k if=${IMGFILE} of=${SDCARD}____ __ __ Exactly the same thing happened as I previously mentioned, got a bunch of boot text then LED4 goes off and nothing else happens.____ __ __ Any advice would be gratefully accepted.____ __ __ *Andy**____* *__ __* __ __ __ __ Hi, could you paste your command to flash SD card here?____ I have just purchased an Origen Board - Full Package. I flashed the SD card with igen-ics-gcc46-samsunglt-stable-blob.img and placed it into the SD card slot. I flicked the power switch and pressed SWITCH then POWER and saw the board booting in terminal. However, after a short period of time LED4 turns off and I do not see the LCD light or show the Android screen. The output in terminal is given below. Is my board faulty or have I not flashed the correct image to the SD card ?____ U-Boot 2011.06-01275-gd6186aa (Feb 17 2012 - 08:54:12) for ORIGEN____ CPU: S5PC210@1000MHz <mailto:S5PC210@1000MHz>____ Board: ORIGEN DRAM: 1 GiB WARNING: Caches not enabled MMC: SAMSUNG SD/MMC: 0 *** Warning - bad CRC, using default environment____ In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 reading boot.scr____ 397 bytes read Running bootscript from mmc0:2 ... ## Executing script at 42000000 reading uImage____ 4049424 bytes read reading uInitrd____ 166156 bytes read ## Booting kernel from Legacy Image at 40007000 ... Image Name: Linux-3.0.4+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4049360 Bytes = 3.9 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Android Ramdisk Image Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 166092 Bytes = 162.2 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK____ Starting kernel ...____ Uncompressing Linux... done, booting the kernel. <5>Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146 <mailto:jenkins-build@ip-10-140-6-146>) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <5>Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). <3>CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 <3>CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 <3>CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 <3>CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 <3>CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 <3>CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 <3>CMA reserve : common, addr is 0x57c00000, size is 0x4000000 <3>CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) <7>exynos4_init_clocks: initializing clocks <6>S3C24XX Clocks, Copyright 2004 Simtec Electronics <3>s3c_register_clksrc: clock armclk has no registers set <3>mout_audss: bad source 0 <7>exynos4_setup_clocks: registering clocks <7>exynos4_setup_clocks: xtal is 24000000 <6>EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000<6>EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>sclk_pwm: source is ext_xtal (0), rate is 24000000 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_cam0: source is xusbxti (1), rate is 0 <6>sclk_cam1: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_mixer: source is sclk_dac (0), rate is 24000000 <6>sclk_fimd0: source is xusbxti (1), rate is 0 <6>sclk_fimd1: source is xusbxti (1), rate is 0 <6>sclk_sata: source is mout_mpll (0), rate is 133333333 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_spi: source is mout_mpll (6), rate is 80000000 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 <7>On node 0 totalpages: 188416 <7> Normal zone: 1472 pages used for memmap <7> Normal zone: 0 pages reserved <7> Normal zone: 186944 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 <7>pcpu-alloc: s6528 r8192 d13952 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 <5>Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2____ <6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 736MB = 736MB total <5>Memory: 601736k/601736k available, 151928k reserved, 0K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) <6>Preemptible hierarchical RCU implementation. <6>NR_IRQS:624 <6>sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms <6>Console: colour dummy device 80x30 <6>console [tty0] enabled Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146 <mailto:jenkins-build@ip-10-140-6-146>) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 CMA reserve : common, addr is 0x57c00000, size is 0x4000000 CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) S3C24XX Clocks, Copyright 2004 Simtec Electronics s3c_register_clksrc: clock armclk has no registers set mout_audss: bad source 0 EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000 EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 sclk_pwm: source is ext_xtal (0), rate is 24000000 sclk_csis: source is xusbxti (1), rate is 0 sclk_csis: source is xusbxti (1), rate is 0 sclk_cam0: source is xusbxti (1), rate is 0 sclk_cam1: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_mixer: source is sclk_dac (0), rate is 24000000 sclk_fimd0: source is xusbxti (1), rate is 0 sclk_fimd1: source is xusbxti (1), rate is 0 sclk_sata: source is mout_mpll (0), rate is 133333333 sclk_spi: source is xusbxti (1), rate is 0 sclk_spi: source is mout_mpll (6), rate is 80000000 sclk_spi: source is xusbxti (1), rate is 0 sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2____ PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 736MB = 736MB total Memory: 601736k/601736k available, 151928k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) Preemptible hierarchical RCU implementation. NR_IRQS:624 sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms Console: colour dummy device 80x30 console <tty0] enabled 6>console [ttySAC2] enabled console [tt<SAC2] enabled 6>Calibrating delay loop... Calibrating delay loop... <c>1992.29 BogoMIPS (lpj=4980736) 1992.29 BogoMIPS<(lpj=4980736) 6>pid_max: default: 32768 minimum: 301 pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: CPU: Testing write buffer coherency: ok ok <6>ftrace: allocating 19856 entries in 59 pages ftrace: allocating 19856 entries in 59 pages <6>CPU0: thread -1, cpu 0, socket 9, mpidr 80000900 CPU0: thread -1, cpu 0, socket 9, <pidr 80000900 6>Calibrating local timer... Calibrating local timer... 249.93MHz. 249.93MHz. <6>hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available <6>L310 cache controller enabled L310 cache cont<oller enabled 6>l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B CPU1: Booted secondary processor <2>CPU1: Unknown IPI message 0x1____ _______________________________________________ linaro-android mailing list linaro-android@lists.linaro.org <mailto:linaro-android@lists.linaro.org> http://lists.linaro.org/mailman/listinfo/linaro-android____ __ __ _______________________________________________ linaro-android mailing list linaro-android@lists.linaro.org <mailto:linaro-android@lists.linaro.org> http://lists.linaro.org/mailman/listinfo/linaro-android
linaro-android mailing list linaro-android@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-android
Hi, Akira:
You use origen for product usage or only for hacking?
-jack
On 21 March 2012 15:32, Akira Tsukamoto akira.tsukamoto@linaro.org wrote:
Hi Andrew,
I completely had the same issue with you and was able to solve it by making the boot image with modified following way. (I should have seen this email earlier, yesterday was Japanese public holiday ;) )
Download these files: boot.tar.bz2 userdata.tar.bz2 system.tar.bz2 from:
https://android-build.linaro.**org/builds/~linaro-android/** origen-ics-gcc46-samsunglt-**stable-blob-12.02-release/https://android-build.linaro.org/builds/%7Elinaro-android/origen-ics-gcc46-samsunglt-stable-blob-12.02-release/
Get the latest linaro-image-tools: $bzr branch lp:linaro-image-tools
If you do not have bzr in your ubuntu, then just: $sudo apt-get install bzr should do.
Create boot image as following command line: $./linaro-image-tools/linaro-**android-media-create --mmc /dev/mmcblk0 --dev origen --system system.tar.bz2 --userdata userdata.tar.bz2 --boot boot.tar.bz2 --extra-boot-args s5p_tvout_fb.hdmi_lcd_display=**1 (My PC has SD slot at /dev/mmcblk0 but change it if it is different for you)
Insert the SD card to Origen then boot it. The Android will show with 1024x600 resolution in the middle of your display.
Please let me know if this helps.
Thanks,
Akira
On 03/21/2012 12:17 PM, Chenglie He wrote:
Hey, Andy
Here we use linaro-android-media-create to burn the sd card. Since I never use the burn steps as you mentioned, so I could not comment on it.
-jack
On 20 March 2012 06:56, Andrew Fraser <afraser@andyfraser.co.uk <mailto:afraser@andyfraser.co.**uk afraser@andyfraser.co.uk>> wrote:
Okay, so I have tried both 12.02 for Android and 12.02 for Ubuntu Desktop both for the Origen board.____
I got the Android image from here: http://releases.linaro.org/12.**02/android/leb-origen/origen-** ics-gcc46-samsunglt-stable-**blob.img.gzhttp://releases.linaro.org/12.02/android/leb-origen/origen-ics-gcc46-samsunglt-stable-blob.img.gz and the Ubuntu from here: http://releases.linaro.org/12.**02/oneiric/ubuntu-desktop/** origen-ubuntu-desktop.img.gz._**___http://releases.linaro.org/12.02/oneiric/ubuntu-desktop/origen-ubuntu-desktop.img.gz.____
My commands to make the Ubuntu image were:____
SDCARD=/dev/sdb____
IMGFILE=origen-ubuntu-desktop.**image____
gunzip ${IMGFILE}.gz____
dd bs=64k if=${IMGFILE} of=${SDCARD}____
I then powered up the Origen board and again, got no output on the LCD and only a small amount of boot information in terminal before the SD card power LED (LED4) went off.____
U-Boot 2011.12 (Feb 16 2012 - 21:52:47) for ORIGEN____
CPU: S5PC210@1000MHz____
Board: ORIGEN____
DRAM: 1 GiB____
WARNING: Caches not enabled____
MMC: SAMSUNG SD/MMC: 0____
In: serial____
Out: serial____
Err: serial____
Hit any key to stop autoboot: 0____
reading uImage____
4082320 bytes read____
reading uInitrd____
2175126 bytes read____
## Booting kernel from Legacy Image at 40007000 ...____
Image Name: Linux____ Image Type: ARM Linux Kernel Image (uncompressed)____ Data Size: 4082256 Bytes = 3.9 MiB____ Load Address: 40008000____ Entry Point: 40008000____ Verifying Checksum ... OK____## Loading init Ramdisk from Legacy Image at 42000000 ...____
Image Name: initramfs____ Image Type: ARM Linux RAMDisk Image (uncompressed)____ Data Size: 2175062 Bytes = 2.1 MiB____ Load Address: 00000000____ Entry Point: 00000000____ Verifying Checksum ... OK____ Loading Kernel Image ... OK____OK____
Starting kernel ...____
Uncompressing Linux... done, booting the kernel.____
For the Android image, I used the following commands:____
SDCARD=/dev/sdb____
IMGFILE=origen-ics-gcc46-**samsunglt-stable-blob.img____
gunzip ${IMGFILE}.gz____
dd bs=64k if=${IMGFILE} of=${SDCARD}____
Exactly the same thing happened as I previously mentioned, got a bunch of boot text then LED4 goes off and nothing else happens.____
Any advice would be gratefully accepted.____
*Andy**____*
*__ __*
Hi, could you paste your command to flash SD card here?____
I have just purchased an Origen Board - Full Package. I flashed the SD card with igen-ics-gcc46-samsunglt-**stable-blob.img and placed it into the SD card slot. I flicked the power switch and pressed SWITCH then POWER and saw the board booting in terminal. However, after a short period of time LED4 turns off and I do not see the LCD light or show the Android screen. The output in terminal is given below. Is my board faulty or have I not flashed the correct image to the SD card ?____
U-Boot 2011.06-01275-gd6186aa (Feb 17 2012 - 08:54:12) for ORIGEN____
CPU: S5PC210@1000MHz mailto:S5PC210@1000MHz____
Board: ORIGEN DRAM: 1 GiB WARNING: Caches not enabled MMC: SAMSUNG SD/MMC: 0 *** Warning - bad CRC, using default environment____
In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 reading boot.scr____
397 bytes read Running bootscript from mmc0:2 ... ## Executing script at 42000000 reading uImage____
4049424 bytes read reading uInitrd____
166156 bytes read ## Booting kernel from Legacy Image at 40007000 ... Image Name: Linux-3.0.4+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4049360 Bytes = 3.9 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Android Ramdisk Image Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 166092 Bytes = 162.2 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK____
Starting kernel ...____
Uncompressing Linux... done, booting the kernel. <5>Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146 <mailto:jenkins-build@ip-10-**140-6-146jenkins-build@ip-10-140-6-146>) (gcc version 4.6.3 20120201
(prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <4>Ignoring unrecognised tag 0x00000000 <5>Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). <3>CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 <3>CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 <3>CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 <3>CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 <3>CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 <3>CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 <3>CMA reserve : common, addr is 0x57c00000, size is 0x4000000 <3>CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) <7>exynos4_init_clocks: initializing clocks <6>S3C24XX Clocks, Copyright 2004 Simtec Electronics <3>s3c_register_clksrc: clock armclk has no registers set <3>mout_audss: bad source 0 <7>exynos4_setup_clocks: registering clocks <7>exynos4_setup_clocks: xtal is 24000000 <6>EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000<6>EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>uclk1: source is mout_mpll (6), rate is 100000000 <6>sclk_pwm: source is ext_xtal (0), rate is 24000000 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_csis: source is xusbxti (1), rate is 0 <6>sclk_cam0: source is xusbxti (1), rate is 0 <6>sclk_cam1: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_fimc: source is xusbxti (1), rate is 0 <6>sclk_mixer: source is sclk_dac (0), rate is 24000000 <6>sclk_fimd0: source is xusbxti (1), rate is 0 <6>sclk_fimd1: source is xusbxti (1), rate is 0 <6>sclk_sata: source is mout_mpll (0), rate is 133333333 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_spi: source is mout_mpll (6), rate is 80000000 <6>sclk_spi: source is xusbxti (1), rate is 0 <6>sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 <7>On node 0 totalpages: 188416 <7> Normal zone: 1472 pages used for memmap <7> Normal zone: 0 pages reserved <7> Normal zone: 186944 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 <7>pcpu-alloc: s6528 r8192 d13952 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 <5>Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2____
<6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 736MB = 736MB total <5>Memory: 601736k/601736k available, 151928k reserved, 0K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) <6>Preemptible hierarchical RCU implementation. <6>NR_IRQS:624 <6>sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms <6>Console: colour dummy device 80x30 <6>console [tty0] enabled Linux version 3.0.4+ (jenkins-build@ip-10-140-6-146 <mailto:jenkins-build@ip-10-**140-6-146jenkins-build@ip-10-140-6-146>) (gcc version 4.6.3 20120201
(prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Feb 17 09:34:26 UTC 2012 CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: ORIGEN Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Truncating RAM at 60000000-7fffffff to -6dffffff (vmalloc region overlap). CMA reserve : jpeg, addr is 0x5e800000, size is 0x1800000 CMA reserve : fimc0, addr is 0x5e300000, size is 0x500000 CMA reserve : fimc1, addr is 0x5de00000, size is 0x500000 CMA reserve : fimc2, addr is 0x5d900000, size is 0x500000 CMA reserve : fimc3, addr is 0x5d400000, size is 0x500000 CMA reserve : fimd, addr is 0x5bc00000, size is 0x1800000 CMA reserve : common, addr is 0x57c00000, size is 0x4000000 CMA reserve : (null), addr is 0x57c00000, size is 0x0 Memory policy: ECC disabled, Data cache writealloc CPU EXYNOS4210 (id 0x43210011) S3C24XX Clocks, Copyright 2004 Simtec Electronics s3c_register_clksrc: clock armclk has no registers set mout_audss: bad source 0 EXYNOS4: PLL settings, A=1000000000, M=800000000, E=96000000 V=108000000 EXYNOS4: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000 ACLK100=100000000, ACLK160=160000000, ACLK133=133333333 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 uclk1: source is mout_mpll (6), rate is 100000000 sclk_pwm: source is ext_xtal (0), rate is 24000000 sclk_csis: source is xusbxti (1), rate is 0 sclk_csis: source is xusbxti (1), rate is 0 sclk_cam0: source is xusbxti (1), rate is 0 sclk_cam1: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_fimc: source is xusbxti (1), rate is 0 sclk_mixer: source is sclk_dac (0), rate is 24000000 sclk_fimd0: source is xusbxti (1), rate is 0 sclk_fimd1: source is xusbxti (1), rate is 0 sclk_sata: source is mout_mpll (0), rate is 133333333 sclk_spi: source is xusbxti (1), rate is 0 sclk_spi: source is mout_mpll (6), rate is 80000000 sclk_spi: source is xusbxti (1), rate is 0 sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000 PERCPU: Embedded 7 pages/cpu @c0f96000 s6528 r8192 d13952 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186944 Kernel command line: console=tty0 console=ttySAC2,115200n8 rootwait ro init=/init androidboot.console=ttySAC2 console=ttySAC2 root=/dev/mmcblk0p2____
PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 736MB = 736MB total Memory: 601736k/601736k available, 151928k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfe800000 - 0xffe00000 ( 22 MB) vmalloc : 0xee800000 - 0xf6000000 ( 120 MB) lowmem : 0xc0000000 - 0xee000000 ( 736 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc078fd14 (7712 kB) .init : 0xc0790000 - 0xc07d5980 ( 279 kB) .data : 0xc07d6000 - 0xc0835930 ( 383 kB) .bss : 0xc0835954 - 0xc098bca8 (1369 kB) Preemptible hierarchical RCU implementation. NR_IRQS:624 sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms Console: colour dummy device 80x30 console <tty0] enabled 6>console [ttySAC2] enabled console [tt<SAC2] enabled 6>Calibrating delay loop... Calibrating delay loop... <c>1992.29 BogoMIPS (lpj=4980736) 1992.29 BogoMIPS<(lpj=4980736) 6>pid_max: default: 32768 minimum: 301 pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 Mount-cache hash table entries: 512 <6>CPU: Testing write buffer coherency: CPU: Testing write buffer coherency: ok ok <6>ftrace: allocating 19856 entries in 59 pages ftrace: allocating 19856 entries in 59 pages <6>CPU0: thread -1, cpu 0, socket 9, mpidr 80000900 CPU0: thread -1, cpu 0, socket 9, <pidr 80000900 6>Calibrating local timer... Calibrating local timer... 249.93MHz. 249.93MHz. <6>hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available <6>L310 cache controller enabled L310 cache cont<oller enabled 6>l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache size: 1048576 B CPU1: Booted secondary processor <2>CPU1: Unknown IPI message 0x1____
______________________________**_________________ linaro-android mailing list linaro-android@lists.linaro.**org linaro-android@lists.linaro.org<mailto: linaro-android@lists.**linaro.org linaro-android@lists.linaro.org> http://lists.linaro.org/**mailman/listinfo/linaro-**android____http://lists.linaro.org/mailman/listinfo/linaro-android____
______________________________**_________________ linaro-android mailing list linaro-android@lists.linaro.**org linaro-android@lists.linaro.org<mailto: linaro-android@lists.**linaro.org linaro-android@lists.linaro.org>
http://lists.linaro.org/**mailman/listinfo/linaro-**androidhttp://lists.linaro.org/mailman/listinfo/linaro-android
______________________________**_________________ linaro-android mailing list linaro-android@lists.linaro.**org linaro-android@lists.linaro.org http://lists.linaro.org/**mailman/listinfo/linaro-**androidhttp://lists.linaro.org/mailman/listinfo/linaro-android
______________________________**_________________ linaro-android mailing list linaro-android@lists.linaro.**org linaro-android@lists.linaro.org http://lists.linaro.org/**mailman/listinfo/linaro-**androidhttp://lists.linaro.org/mailman/listinfo/linaro-android
Hi Jack,
On 03/21/2012 04:57 PM, Chenglie He wrote:
You use origen for product usage or only for hacking?
Am, I am not quite sure about your question since hacking is one of the way for the product usage. Lets move to private email if it is not technical discussion.
Regards,
Akira
linaro-android@lists.linaro.org
-
Akira Tsukamoto -
Andrew Fraser -
Chenglie He