Hi Kim,
I was on a sick leave, please excuse the delayed response.
On 04/02/2023 00:06, Kim Steiner wrote:
Hi Dmitry,
Did you receive the new hd-sdi camera? Are you able to get video?
No, not yet. The parcel is stuck.
Have you looked into how to use a single GPU frequency in the 5.15 kernel?
The frequencies for the GPU are handled both by the kernel and by the GPMU, a separate IP core. I'm debugging the way the kernel interacts with the GPMU.
Thanks,
Kim
*From:* Kim Steiner *Sent:* Wednesday, January 25, 2023 12:02 PM *To:* Jordan Holt jordan.holt@sightlineapplications.com; Steve Olson steve.olson@sightlineapplications.com; Dmitry Baryshkov dmitry.baryshkov@linaro.org *Cc:* Paul Neuhardt paul.neuhardt@linaro.org; sightlineapplications@lists.linaro.org *Subject:* RE: [Sightlineapplications] Re: Project Status and Burn Report
Hi Dmitry,
- I put a 5.15 kernel 4000 installer here: https://www.dropbox.com/s/aktq45ybqty1640/SLAUpgrade4000.msi?dl=0 https://www.dropbox.com/s/aktq45ybqty1640/SLAUpgrade4000.msi?dl=0
- Our device tree sources, you can find here: https://www.dropbox.com/s/gevgqyu79mtqy14/linaro_5.15_files.zip?dl=0 https://www.dropbox.com/s/gevgqyu79mtqy14/linaro_5.15_files.zip?dl=0
- I’m not 100% on what you will need if you use your 5.15 kernel build and want to run media-ctl and v4l2-ctl tools from the command line. What works for me is to
A. Run our VTNext_ARM64_Release.out – this is doing some FPGA reset and setup of GPIOs
B. sudo media-ctl -d /dev/media0 -l '"msm_csiphy2":1->"msm_csid1":0[1],"msm_csid1":1->"msm_ispif1":0[1],"msm_ispif1":1->"msm_vfe0_rdi1":0[1]'
sudo media-ctl -d /dev/media0 -V '"mt9034 5-003a":0[fmt:UYVY2X8/1280x720],"msm_csiphy2":0[fmt:UYVY2X8/1280x720],"msm_csid1":0[fmt:UYVY2X8/1280x720],"msm_ispif1":0[fmt:UYVY2X8/1280x720],"msm_vfe0_rdi1":0[fmt:UYVY2X8/1280x720]'
sudo v4l2-ctl --set-fmt-video=width=1280,height=720,pixelformat='UYVY' -d /dev/video1
v4l2-ctl --stream-mmap=4 --verbose -d /dev/video1
polling_ms is in this file - drivers/gpu/drm/msm/msm_gpu_devfreq.c:90: .polling_ms = 50,
If #3 does not work for you, then let me know and I will proceed with getting access to our kernel repository.
Thanks,
Kim
*From:* Jordan Holt <jordan.holt@sightlineapplications.com mailto:jordan.holt@sightlineapplications.com> *Sent:* Wednesday, January 25, 2023 10:20 AM *To:* Steve Olson <steve.olson@sightlineapplications.com mailto:steve.olson@sightlineapplications.com>; Dmitry Baryshkov <dmitry.baryshkov@linaro.org mailto:dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com mailto:kim.steiner@sightlineapplications.com> *Cc:* Paul Neuhardt <paul.neuhardt@linaro.org mailto:paul.neuhardt@linaro.org>; sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org *Subject:* RE: [Sightlineapplications] Re: Project Status and Burn Report
I tried to send with a picture, but mail is “being held for review”.
*Jordan Holt | **CTO **| SightLine Applications Inc. |**Onboard Video**Processing****| *he/him | 503 724-9727**
Please note our *NEW PORTLAND ADDRESS* is:
/5711 S Hood Ave., Suite A/
/Portland, OR 97239/
*From:* Jordan Holt *Sent:* Wednesday, January 25, 2023 10:18 AM *To:* Steve Olson <steve.olson@sightlineapplications.com mailto:steve.olson@sightlineapplications.com>; Dmitry Baryshkov <dmitry.baryshkov@linaro.org mailto:dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com mailto:kim.steiner@sightlineapplications.com> *Cc:* Paul Neuhardt <paul.neuhardt@linaro.org mailto:paul.neuhardt@linaro.org>; sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org *Subject:* RE: [Sightlineapplications] Re: Project Status and Burn Report
This should be the settings. If you can get it to display on your analog TV, click the middle button (press in) then toggle it up/down to get to *System* then press in then you want Frame Rate and Freq like below.
Jordan Holt | CTO | SightLine Applications Inc. | Onboard Video Processing | he/him | 503 724-9727
Please note our NEW PORTLAND ADDRESS is:
5711 S Hood Ave., Suite A
Portland, OR 97239
-----Original Message----- From: Steve Olson <steve.olson@sightlineapplications.com mailto:steve.olson@sightlineapplications.com> Sent: Wednesday, January 25, 2023 10:14 AM To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org mailto:dmitry.baryshkov@linaro.org>; Kim Steiner <kim.steiner@sightlineapplications.com mailto:kim.steiner@sightlineapplications.com> Cc: Jordan Holt <jordan.holt@sightlineapplications.com mailto:jordan.holt@sightlineapplications.com>; Paul Neuhardt <paul.neuhardt@linaro.org mailto:paul.neuhardt@linaro.org>; sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org Subject: RE: [Sightlineapplications] Re: Project Status and Burn Report
Yes, it's just NTSC composite video. I think can configure for PAL too, but to do that you need to be able to see the video to do that.
In parallel, I've started the process of sending you another camera and board.
Steve
Steve Olson | CEO | SightLine Applications Inc. | Onboard Video Processing | he/him
503 975-8478 (mobile) | www.sightlineapplications.com http://www.sightlineapplications.com
-----Original Message-----
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org mailto:dmitry.baryshkov@linaro.org>
Sent: Wednesday, January 25, 2023 9:50 AM
To: Kim Steiner <kim.steiner@sightlineapplications.com mailto:kim.steiner@sightlineapplications.com>
Cc: Jordan Holt <jordan.holt@sightlineapplications.com mailto:jordan.holt@sightlineapplications.com>; Paul Neuhardt <paul.neuhardt@linaro.org mailto:paul.neuhardt@linaro.org>; sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org
Subject: [Sightlineapplications] Re: Project Status and Burn Report
On 25/01/2023 19:47, Kim Steiner wrote:
Hi Dmitry,
One other thought in terms of getting the hd-sdi camera to work is to
try the analog out connector. It is the yellow connector on the hd-sdi camera cabling. Would you have a way to display this?
I'll check if I can find a capture device. Is it just a composite video signal or something more intelligent?
Thanks,
Kim
-----Original Message-----
From: Kim Steiner
Sent: Tuesday, January 24, 2023 3:31 PM
To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org
mailto:dmitry.baryshkov@linaro.org>
Cc: Jordan Holt <jordan.holt@sightlineapplications.com
mailto:jordan.holt@sightlineapplications.com>; Paul Neuhardt
<paul.neuhardt@linaro.org mailto:paul.neuhardt@linaro.org>;
sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org
Subject: RE: [Sightlineapplications] Re: Project Status and Burn
Report
Resending with basically no message then this one:
Hi Dmitry,
In regards to our testing, we have seen a GPU fault crash with our
custom board (with 5.15 kernel) during temp testing. On one unit, we have seen the GPU fault crash at 118F (47C) while our custom board is sitting on a desk. The output of the GPU fault crash occurs once and our application continues to run. What do you think of this output?:
[ 156.660355] msm 900000.mdss: CP | opcode error | possible
opcode=0x00000000 [ 156.662139] msm 900000.mdss: [drm:a5xx_irq] *ERROR* gpu fault ring 0 fence 5e47 status 800001C1 rb 1820/17e6 ib1 0000000003C1B000/0000 ib2 0000000001483000/0000 [ 156.666297] msm 900000.mdss: [drm:recover_worker] *ERROR* A530: hangcheck recover!
[ 156.680832] msm 900000.mdss: [drm:recover_worker] *ERROR* A530:
offending task: VTNext_ARM:sq0 (./VTNext_ARM64_Release.out -FULL) [ 156.699196] revision: 530 (5.3.0.2) [ 156.699341] msm 900000.mdss: [drm:a5xx_irq] *ERROR* gpu fault ring 0 fence 5e47 status 800001C1 rb 1820/17e6 ib1 0000000003C1B000/0000 ib2 0000000001483000/0000
[ 156.699833] rb 0: fence: 24134/24135
[ 156.717750] rptr: 6081
[ 156.721300] rb wptr: 6118
[ 156.724047] rb 1: fence: 0/0
[ 156.726786] rptr: 0
[ 156.729795] rb wptr: 0
[ 156.732207] rb 2: fence: 0/0
[ 156.734670] rptr: 0
[ 156.737779] rb wptr: 0
[ 156.740191] rb 3: fence: 0/0
[ 156.742649] rptr: 0
[ 156.745768] rb wptr: 0
[ 156.748186] CP_SCRATCH_REG0: 0
[ 156.750641] CP_SCRATCH_REG1: 0
[ 156.753762] CP_SCRATCH_REG2: 24134
[ 156.756812] CP_SCRATCH_REG3: 0
[ 156.760169] CP_SCRATCH_REG4: 0
[ 156.763222] CP_SCRATCH_REG5: 0
[ 156.766262] CP_SCRATCH_REG6: 0
[ 156.769300] CP_SCRATCH_REG7: 0
[ 156.773675] msm 900000.mdss: [drm:recover_worker] *ERROR* A530:
hangcheck recover!
Thanks,
Kim
--
With best wishes
Dmitry
Sightlineapplications mailing list -- sightlineapplications@lists.linaro.org mailto:sightlineapplications@lists.linaro.org
To unsubscribe send an email to sightlineapplications-leave@lists.linaro.org mailto:sightlineapplications-leave@lists.linaro.org