On 04/08/14 16:28, Hanjun Guo wrote:
Introduce ACPI_IRQ_MODEL_GIC which is needed for ARM64 as GIC is used, and then register device's gsi with the core IRQ subsystem.
acpi_register_gsi() is similar to DT based irq_of_parse_and_map(), since gsi is unique in the system, so use hwirq number directly for the mapping.
Originally-by: Amit Daniel Kachhap amit.daniel@samsung.com Signed-off-by: Hanjun Guo hanjun.guo@linaro.org
arch/arm64/kernel/acpi.c | 73 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/acpi/bus.c | 3 ++ include/linux/acpi.h | 1 + 3 files changed, 77 insertions(+)
diff --git a/arch/arm64/kernel/acpi.c b/arch/arm64/kernel/acpi.c index ac7ab34..621ced8 100644 --- a/arch/arm64/kernel/acpi.c +++ b/arch/arm64/kernel/acpi.c @@ -34,6 +34,12 @@ EXPORT_SYMBOL(acpi_pci_disabled); static int enabled_cpus; /* Processors (GICC) with enabled flag in MADT */
/*
- Since we're on ARM, the default interrupt routing model
- clearly has to be GIC.
- */
+enum acpi_irq_model_id acpi_irq_model = ACPI_IRQ_MODEL_GIC;
+/*
- __acpi_map_table() will be called before page_init(), so early_ioremap()
- or early_memremap() should be called here to for ACPI table mapping.
*/ @@ -169,6 +175,73 @@ static int __init acpi_parse_madt_gic_cpu_interface_entries(void) return 0; }
+int acpi_gsi_to_irq(u32 gsi, unsigned int *irq) +{
- *irq = irq_find_mapping(NULL, gsi);
- return 0;
+} +EXPORT_SYMBOL_GPL(acpi_gsi_to_irq);
+/*
- success: return IRQ number (>0)
- failure: return =< 0
- */
+int acpi_register_gsi(struct device *dev, u32 gsi, int trigger, int polarity) +{
- unsigned int irq;
- unsigned int irq_type;
- /*
* ACPI have no bindings to indicate SPI or PPI, so we* use different mappings from DT in ACPI.** For FDT* PPI interrupt: in the range [0, 15];* SPI interrupt: in the range [0, 987];** For ACPI, GSI should be unique so using* the hwirq directly for the mapping:* PPI interrupt: in the range [16, 31];* SPI interrupt: in the range [32, 1019];*/- if (trigger == ACPI_EDGE_SENSITIVE &&
polarity == ACPI_ACTIVE_LOW)irq_type = IRQ_TYPE_EDGE_FALLING;- else if (trigger == ACPI_EDGE_SENSITIVE &&
polarity == ACPI_ACTIVE_HIGH)irq_type = IRQ_TYPE_EDGE_RISING;- else if (trigger == ACPI_LEVEL_SENSITIVE &&
polarity == ACPI_ACTIVE_LOW)irq_type = IRQ_TYPE_LEVEL_LOW;- else if (trigger == ACPI_LEVEL_SENSITIVE &&
polarity == ACPI_ACTIVE_HIGH)irq_type = IRQ_TYPE_LEVEL_HIGH;- else
irq_type = IRQ_TYPE_NONE;- /*
* Since only one GIC is supported in ACPI 5.0, we can* create mapping refer to the default domain*/- irq = irq_create_mapping(NULL, gsi);
- if (!irq)
return irq;- /* Set irq type if specified and different than the current one */
- if (irq_type != IRQ_TYPE_NONE &&
irq_type != irq_get_trigger_type(irq))irq_set_irq_type(irq, irq_type);- return irq;
+} +EXPORT_SYMBOL_GPL(acpi_register_gsi);
Not sure if acpi_gsi_to_irq and acpi_{,un}register_gsi belong here. These are GIC specific and should belong to GIC driver IMO.
Regards, Sudeep