Add CFLAGS and LDFLAGS for each feature to be checked during the
build. This allows to pass particular flags and parameters to the
feature checks compilation.
Use the per-feature check flags for the unwinding feature in order
to correctly compile the test-all, libunwind and libunwind-debug-frame
feature checks.
This change set simplifies the flags passing mechanism between the
Makefiles in config/Makefile and config/feature-checks; this
could be farther optimized by moving the compilation flags to the
per-feature check flags for all features to be checked.
Tested on x86_64, ARMv7 and ARMv8 with and without LIBUNWIND_DIR
set in 'make -C tools/perf'
Jean Pihet (2):
perf: add per-feature check flags
perf: unwinding: use the per-feature check flags
tools/perf/config/Makefile | 52 ++++++++++++++++++-------------
tools/perf/config/feature-checks/Makefile | 8 ++---
2 files changed, 34 insertions(+), 26 deletions(-)
--
1.7.11.7
From: Al Stone <al.stone(a)linaro.org>
This series of patches starts with Hanjun's patch to create a kernel
config item for CONFIG_ACPI_REDUCED_HARDWARE [0]. Building on that, I
then reviewed all of the code that touched any of several fields in the
FADT that the OSPM is supposed to ignore when ACPI is in Hardware Reduced
mode [1]. Any time there was a use of one of the fields to be ignored,
I evaluated whether or not the code was implementing Hardware Reduced
mode correctly. Similarly, for each the flags in the FADT flags field
that are to be ignored in Hardware Reduced mode, the kernel code was again
scanned for proper usage. The remainder of the patches are to fix all of
the situations I could find where the kernel would not behave correctly
in this ACPI mode.
These seem to work just fine on the RTSM model for ARMv7, both with and
without ACPI enabled, and with and without ACPI_REDUCED_HARDWARE enabled;
similarly for the FVP model for ARMv8. The patches for ACPI on ARM
hardware will be coming later but they presume that reduced HW mode is
functioning correctly. In the meantime, there's no way I can think of
to test all possible scenarios so feedback would be greatly appreciated.
[0] List at https://wiki.linaro.org/LEG/Engineering/Kernel/ACPI/AcpiReducedHw#Section_5…
[1] Please see the ACPI Specification v5.0 for details on Hardware Reduced
mode.
Changes for v2:
-- Remove patch that was outside of reduced HW mode changes
-- Simplify CONFIG_ACPI_REDUCED_HARDWARE in Kconfig
-- Simplify use of CONFIG_ACPI_REDUCED_HARDWARE in #ifdefs
-- Ensure changelogs are present
-- Combine and simplify previous patches 8 & 10
Al Stone (6):
ACPI: introduce CONFIG_ACPI_REDUCED_HARDWARE to enable this ACPI mode
ACPI: bus master reload not supported in reduced HW mode
ACPI: HW reduced mode does not allow use of the FADT sci_interrupt
field
ACPI: ARM: exclude DMI calls
ACPI: do not reserve memory regions for some FADT entries in HW
reduced mode
ACPI: in HW reduced mode, using FADT PM information is not allowed.
drivers/acpi/Kconfig | 8 ++++++++
drivers/acpi/bus.c | 3 ++-
drivers/acpi/osl.c | 24 ++++++++++++------------
drivers/acpi/pci_link.c | 2 ++
drivers/acpi/processor_idle.c | 16 ++++++++++++++--
include/acpi/platform/aclinux.h | 4 ++++
include/linux/dmi.h | 2 +-
7 files changed, 43 insertions(+), 16 deletions(-)
--
1.8.3.1
