linaro-kernel

linaro-kernel@lists.linaro.org

10095 discussions

by john stultz

Was out sick weds, so not a super productive week. === Highlights === * Added EARLYSUSPEND to linaro+android defconfigs * Made final 11.11 linaro+android release * After being nudged by Thomas, sent out first draft of a large patchset reworking some of the timekeeping locking. * Reviewed and acked sched_clock overflow fix. * Helped with Android Image testing for 11.11 release * Submitted config fragment management script to akpm and it was included into the -mm tree. * Revised madvise volatile patchset a few times preping for lkml discussion. Got some good feedback that made me think it would be better to rework the patch to use fadvise instead of madvise. Started efforts to convert the interface over. === Plans === * Finish madvise->fadvise conversion, do one last cleanup and send to lkml. * Take another pass at the timekeeping locking for Thomas. * Push queued patches for 3.3 to Thomas. === Issues === * None

14 years

[Activity] (Linus Walleij) 2011-11-12 - 2011-11-18

by Linus Walleij

== Linus Walleij linusw == === Highlights === * Very active discussions around the pinctrl v2 patch sent sent out last week, much good feedback and slowly building consensus. https://blueprints.launchpad.net/linux-linaro/+spec/pinctrl-pinprops-2011.11 * Refactored U300 GPIO to live in pinctrl as sibling to the U300 pinmux controller. Also implemented pin multiplexing and draft pin configuration interface (subject to change). This was done as a proof-of-concept that the pincontrol subsystem is good for something that exists out there. Will be sent out back-to-back with the pinconfig patch set. * Harvesting some fixes for pinctrl * Looked after the GPIO subsystem -rc fixes for Grant but haven't seen many patches, discussed a few non-rc patches. * A lot of discussion around the PL022 driver thread safety, led to the submission of the patch entitled: "spi/pl022: make the chip deselect handling thread safe" * Lots of mailing and reading trying to understand how to get my kernel.org git repo back online. === Plans === * Drive generalization of Nomadik GPIO by using the pinctrl framework. drivers/gpio/gpio-nomadik.c * Test the PL08x patches on the Ericsson Research PB11MPCore and submit platform data for using pl08x DMA on that platform. * Pushed out the AB8500 HWMON driver, will try to address review comments. * Look into other Ux500 stuff in need of mainlining... === Issues === * Pretty much internal fuzz at my parent company due to re- organization. Thanks, Linus Walleij

14 years

ACTIVITY (Rajendra Nayak) Nov 14 - Nov 18

by Rajendra Nayak

== Rajendra Nayak <rnayak> == === Highlights === * Posted an early RFC version of the omap pinmux driver. Working on improving it by adding missing pieces and based on review comments from Tony/Linus. * Posted omap serial dt support. Reworked to handle some shortcomings in the hmwod framework. Still, has missing low power (PM) support, which is currently implemented using platform func pointers. Need to work on a solution as people seem to dislike auxdata approach as its ugly. * Posted v5 of regulator core bindings. TWL regulator support still has dependencies on other (i2c/gpio/twl) OMAP dt patches. * Reworking TWL-smps support patches, based on the latest ones (post ELC discussions of Tero with Kevin/Benoit) sent across by Tero Kristo. === Plans === * Work on further improving the omap pinmux driver and add support for all OMAPs. * Rework any OMAP driver DT support patches.

14 years

[PATCH] pinctrl: add a gpio and pinctrl driver for samsung io-pad controllers

by Thomas Abraham

Add a combined gpio and pinctrl io-pad driver for Samsung platforms. Signed-off-by: Thomas Abraham <thomas.abraham(a)linaro.org> --- This driver supports gpio, pinctrl and pinmux functionality. At present, all the possible pin groups and pin functions have not been added. This driver is designed to be reusable across all Samsung SoC's and when this implemtation is complete, the gpio driver in driver/gpio for samsung platforms can be phased out. Features like GPIO interrupt support and pin-config support are yet to be added. drivers/pinctrl/Kconfig | 6 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-samsung.c | 688 +++++++++++++++++++++++++++++++++++++ 3 files changed, 695 insertions(+), 0 deletions(-) create mode 100644 drivers/pinctrl/pinctrl-samsung.c diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index e17e2f8..55739d2 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -30,6 +30,12 @@ config PINMUX_U300 depends on ARCH_U300 select PINMUX +config PINCTRL_SAMSUNG + bool "Samsung pinctrl driver" + default y + depends on PLAT_SAMSUNG + select PINMUX + endmenu endif diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index bdc548a..463b934 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_PINCTRL) += core.o obj-$(CONFIG_PINMUX) += pinmux.o obj-$(CONFIG_PINMUX_SIRF) += pinmux-sirf.o obj-$(CONFIG_PINMUX_U300) += pinmux-u300.o +obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o diff --git a/drivers/pinctrl/pinctrl-samsung.c b/drivers/pinctrl/pinctrl-samsung.c new file mode 100644 index 0000000..0705a8d --- /dev/null +++ b/drivers/pinctrl/pinctrl-samsung.c @@ -0,0 +1,688 @@ +/* + * pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's. + * + * Copyright (c) 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * Copyright (c) 2011 Linaro Ltd + * http://www.linaro.org + * + * Author: Thomas Abraham <thomas.abraham(a)linaro.org> + * + * This driver is divided into two main components, gpiolib subsystem interface + * and the pin-controller subsystem interface. This model help to better + * abstract the details of pad controller for all the Samsung SoC's. The driver + * is reusuable on all the Samsung SoC's, though the data that could get + * accumulated in this file could be daunting. + * + * The driver functions are kept as generic as possible such that they are + * usable across multiple Samsung SoC's. The driver data differentiates the + * operation of the driver for each SoC by describing the complete + * pad-controller structure to the driver and the generic driver code operates + * on the SoC specific driver data. The driver data also includes runtime data + * required for the operation of the driver. + * + * List of ToDo's: + * 1. Add GPIO Interrupt support. + * 2. Add external interrupt (wakeup) support. + * 3 Add power management support. + * 4 Add pin-config (pull up/down, driver strength) support. + * 5. Find a better way to populate data about pins and functions. + * 6. Add driver data, pins, groups, functions for all Samsung SoC's and test. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/err.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/gpio.h> + +#include <plat/map-base.h> +#include <plat/map-s5p.h> + +#define DAT_REG 0x4 + +/** + * struct samsung_pin_bank: represent a controller pin-bank. + * @reg_offset: starting offset of the pin-bank registers. + * @pin_base: starting pin number of the bank. + * @nr_pins: number of pins included in this bank. + * @func_width: width of the function selector bit field. + * @irq_base: starting eint number of the bank. + */ +struct samsung_pin_bank { + unsigned int reg_offset; + unsigned int pin_base; + unsigned int nr_pins; + unsigned int func_width; + unsigned int irq_base; +}; + +/** + * struct samsung_pin_ctrl: represent a pin controller. + * @pin_banks: list of pin banks included in this controller. + * @nr_banks: number of pin banks. + * @base: starting system wide pin number. + * @nr_pins: number of pins supported by the controller. + * @label: for debug information. + */ +struct samsung_pin_ctrl { + struct samsung_pin_bank *pin_banks; + unsigned int nr_banks; + unsigned int base; + unsigned int nr_pins; + char *label; +}; + +/** + * struct samsung_pinctrl_drv_data: wrapper for holding driver data together. + * @virt_base: register base address of the controller. + * @ctrl: pin controller instance managed by the driver. + * @pctl: pin controller descriptor registered with the pinctrl subsystem. + * @pctl_dev: cookie representing pinctrl device instance. + * @pin_groups: list of pin groups available to the driver. + * @nr_groups: number of such pin groups. + * @pmx_functions: list of pin functions available to the driver. + * @nr_function: number of such pin functions. + * @gc: gpio_chip instance registered with gpiolib. + */ +struct samsung_pinctrl_drv_data { + void __iomem *virt_base; + struct samsung_pin_ctrl *ctrl; + struct pinctrl_desc *pctl; + struct pinctrl_dev *pctl_dev; + const struct samsung_pin_group *pin_groups; + unsigned int nr_groups; + const struct samsung_pmx_func *pmx_functions; + unsigned int nr_functions; + struct gpio_chip *gc; +}; + +/** + * struct samsung_pin_group: represent group of pins of a pinmux function. + * @name: name of the pin group, used to lookup the group. + * @pins: the pins included in this group. + * @num_pins: number of pins included in this group. + * @func: the function number to be programmed when selected. + */ +struct samsung_pin_group { + const char *name; + const unsigned int *pins; + const unsigned int num_pins; + unsigned int func; +}; + +/** + * struct samsung_pmx_func: represent a pin function. + * @name: name of the pin function, used to lookup the function. + * @groups: one or more names of pin groups that provide this function. + * @num_groups: number of groups included in @groups. + */ +struct samsung_pmx_func { + const char *name; + const char * const *groups; + const unsigned num_groups; +}; + +/* Note: The pin group list needs to be further populated */ +static unsigned int exynos4210_spi0_pins[] = { + EXYNOS4_GPB(0), EXYNOS4_GPB(1), EXYNOS4_GPB(2), EXYNOS4_GPB(3), +}; + +static unsigned int exynos4210_i2c0_pins[] = { + EXYNOS4_GPD1(0), EXYNOS4_GPD1(1), +}; + +static unsigned int exynos4210_sdhci0_pins[] = { + EXYNOS4_GPK0(0), EXYNOS4_GPK0(1), EXYNOS4_GPK0(2), EXYNOS4_GPK0(3), + EXYNOS4_GPK0(4), EXYNOS4_GPK0(5), EXYNOS4_GPK0(6), EXYNOS4_GPK0(7) +}; + +static unsigned int exynos4210_sdhci2_pins[] = { + EXYNOS4_GPK2(0), EXYNOS4_GPK2(1), EXYNOS4_GPK2(2), EXYNOS4_GPK2(3), + EXYNOS4_GPK2(4), EXYNOS4_GPK2(5), EXYNOS4_GPK2(6), EXYNOS4_GPK2(7) +}; + +static unsigned int exynos4210_i2s0_pins[] = { + EXYNOS4_GPZ(0), EXYNOS4_GPZ(1), EXYNOS4_GPZ(2), EXYNOS4_GPZ(3), + EXYNOS4_GPZ(4), EXYNOS4_GPZ(5), EXYNOS4_GPZ(6), EXYNOS4_GPZ(7) +}; + +static unsigned int exynos4210_pcm0_pins[] = { + EXYNOS4_GPZ(0), EXYNOS4_GPZ(1), EXYNOS4_GPZ(2), EXYNOS4_GPZ(3), + EXYNOS4_GPZ(4), EXYNOS4_GPZ(5), +}; + +#define PIN_GROUP(n, p, f) \ + { \ + .name = n, \ + .pins = p, \ + .num_pins = ARRAY_SIZE(p), \ + .func = f \ + } + +/* + * list of pin groups available for pin-controller[0] of Exynos4210. + * Note: This listed needs to be populated. + */ +static const struct samsung_pin_group exynos4210_pin_groups0[] = { + PIN_GROUP("spi0_grp", exynos4210_spi0_pins, 2), + PIN_GROUP("i2c0_grp", exynos4210_i2c0_pins, 2), +}; + +/* + * list of pin groups available for pin-controller[1] of Exynos4210. + * Note: This listed needs to be populated. + */ +static const struct samsung_pin_group exynos4210_pin_groups1[] = { + PIN_GROUP("sdhci0_grp", exynos4210_sdhci0_pins, 2), + PIN_GROUP("sdhci2_grp", exynos4210_sdhci2_pins, 2), +}; + +/* + * list of pin groups available for pin-controller[2] of Exynos4210. + * Note: This listed needs to be populated. + */ +static const struct samsung_pin_group exynos4210_pin_groups2[] = { + PIN_GROUP("i2s0_grp", exynos4210_i2s0_pins, 2), + PIN_GROUP("pcm0_grp", exynos4210_pcm0_pins, 2), +}; + +/* check if the selector is a valid pin group selector */ +static int samsung_list_groups(struct pinctrl_dev *pctldev, unsigned selector) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + if (selector >= drvdata->nr_groups) + return -EINVAL; + return 0; +} + +/* return the name of the group selected by the group selector */ +static const char *samsung_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + return drvdata->pin_groups[selector].name; +} + +/* return the pin numbers associated with the specified group */ +static int samsung_get_group_pins(struct pinctrl_dev *pctldev, + unsigned selector, const unsigned **pins, unsigned *num_pins) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + *pins = drvdata->pin_groups[selector].pins; + *num_pins = drvdata->pin_groups[selector].num_pins; + return 0; +} + +/* list of pinctrl callbacks for the pinctrl core */ +static struct pinctrl_ops samsung_pctrl_ops = { + .list_groups = samsung_list_groups, + .get_group_name = samsung_get_group_name, + .get_group_pins = samsung_get_group_pins, +}; + +static const char * const i2c0_grp[] = { "i2c0_grp" }; +static const char * const spi0_grp[] = { "spi0_grp" }; +static const char * const sdhci0_grp[] = { "sdhci0_grp" }; +static const char * const sdhci2_grp[] = { "sdhci2_grp" }; +static const char * const i2s0_grp[] = { "i2s0_grp" }; +static const char * const pcm0_grp[] = { "pcm0_grp" }; + +#define PMX_FUNC(n, g) \ + { \ + .name = n, \ + .groups = g, \ + .num_groups = ARRAY_SIZE(g), \ + } + +/* + * list of function names supported by the pinmux vertical. + * Note: All functions to be populated here. + */ +static const struct samsung_pmx_func exynos4210_pmx_functions0[] = { + PMX_FUNC("spi0", spi0_grp), + PMX_FUNC("i2c0", i2c0_grp), +}; + +/* + * list of function names supported by the pinmux vertical. + * Note: All functions to be populated here. + */ +static const struct samsung_pmx_func exynos4210_pmx_functions1[] = { + PMX_FUNC("sdhci0", sdhci0_grp), + PMX_FUNC("sdhci2", sdhci2_grp), +}; + +/* + * list of function names supported by the pinmux vertical. + * Note: All functions to be populated here. + */ +static const struct samsung_pmx_func exynos4210_pmx_functions2[] = { + PMX_FUNC("i2s0", i2s0_grp), + PMX_FUNC("pcm0", pcm0_grp), +}; + +/* check if the selector is a valid pin function selector */ +static int samsung_pinmux_list_funcs(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + if (selector >= drvdata->nr_groups) + return -EINVAL; + return 0; +} + +/* return the name of the pin function specified */ +static const char *samsung_pinmux_get_fname(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + return drvdata->pmx_functions[selector].name; +} + +/* return the groups associated for the specified function selector */ +static int samsung_pinmux_get_groups(struct pinctrl_dev *pctldev, + unsigned selector, const char * const **groups, + unsigned * const num_groups) +{ + struct samsung_pinctrl_drv_data *drvdata; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + *groups = drvdata->pmx_functions[selector].groups; + *num_groups = drvdata->pmx_functions[selector].num_groups; + return 0; +} + +/* + * given a pin number that is local to a pin controller, find out the pin bank + * and the register base of the pin bank. + */ +static void pin_to_reg_bank(struct gpio_chip *gc, unsigned pin, + void __iomem **reg, unsigned long *offset, + struct samsung_pin_bank **bank) +{ + struct samsung_pinctrl_drv_data *drvdata; + struct samsung_pin_bank *b; + + drvdata = dev_get_drvdata(gc->dev); + b = drvdata->ctrl->pin_banks; + + while (b->pin_base + b->nr_pins < pin) + b++; + + *reg = drvdata->virt_base + b->reg_offset; + *offset = pin - b->pin_base; + if (bank) + *bank = b; + + /* some banks have two config registers in a single bank */ + if (*offset * b->func_width > BITS_PER_LONG) + *reg += 4; +} + +/* enable or disable a pinmux function */ +static void samsung_pimux_setup(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group, bool enable) +{ + struct samsung_pinctrl_drv_data *drvdata; + const unsigned int *pin; + unsigned long data, pin_offset, cnt; + struct samsung_pin_bank *bank; + void __iomem *reg; + unsigned int mask, shift; + + drvdata = pinctrl_dev_get_drvdata(pctldev); + pin = drvdata->pin_groups[group].pins; + + /* + * for each pin in the pin group selected, program the correspoding pin + * pin function number in the config register. + */ + for (cnt = 0; cnt < drvdata->pin_groups[group].num_pins; cnt++, pin++) { + pin_to_reg_bank(drvdata->gc, *pin - drvdata->ctrl->base, + &reg, &pin_offset, &bank); + mask = (1 << bank->func_width) - 1; + shift = pin_offset * bank->func_width; + + data = readl(reg); + data &= ~(mask << shift); + if (enable) + data |= drvdata->pin_groups[group].func << shift; + writel(data, reg); + } +} + +/* enable a specified pinmux by writing to registers */ +static int samsung_pinmux_enable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + samsung_pimux_setup(pctldev, selector, group, true); + return 0; +} + +/* disable a specified pinmux by writing to registers */ +static void samsung_pinmux_disable(struct pinctrl_dev *pctldev, + unsigned selector, unsigned group) +{ + samsung_pimux_setup(pctldev, selector, group, false); +} + +/* list of pinmux callbacks for the pinmux vertical in pinctrl core */ +static struct pinmux_ops samsung_pinmux_ops = { + .list_functions = samsung_pinmux_list_funcs, + .get_function_name = samsung_pinmux_get_fname, + .get_function_groups = samsung_pinmux_get_groups, + .enable = samsung_pinmux_enable, + .disable = samsung_pinmux_disable, +}; + +/* gpiolib gpio_set callback function */ +static void samsung_gpio_set(struct gpio_chip *gc, unsigned offset, int value) +{ + void __iomem *reg; + unsigned long pin_offset, data; + + pin_to_reg_bank(gc, offset, &reg, &pin_offset, NULL); + data = readl(reg + DAT_REG); + data &= ~(1 << pin_offset); + if (value) + data |= 1 << pin_offset; + __raw_writel(data, reg + DAT_REG); +} + +/* gpiolib gpio_get callback function */ +static int samsung_gpio_get(struct gpio_chip *gc, unsigned offset) +{ + void __iomem *reg; + unsigned long pin_offset, data; + + pin_to_reg_bank(gc, offset, &reg, &pin_offset, NULL); + data = readl(reg + DAT_REG); + data >>= pin_offset; + data &= 1; + return data; +} + +/* register the pinctrl interface with the pinctrl subsystem */ +static int __init samsung_pinctrl_register(struct platform_device *pdev, + struct samsung_pinctrl_drv_data *drvdata) +{ + struct pinctrl_desc *ctrldesc = drvdata->pctl; + struct pinctrl_pin_desc *pindesc; + int pin; + + pindesc = devm_kzalloc(&pdev->dev, sizeof(*pindesc) * + drvdata->ctrl->nr_pins, GFP_KERNEL); + if (!pindesc) { + dev_err(&pdev->dev, "mem alloc for pin descriptors failed\n"); + return -ENOMEM; + } + ctrldesc->pins = pindesc; + ctrldesc->npins = drvdata->ctrl->nr_pins; + ctrldesc->maxpin = drvdata->ctrl->nr_pins; + + /* dynamically create the pindesc, ignore the name for pindesc */ + for (pin = 0; pin < ctrldesc->maxpin; pin++, pindesc++) + pindesc->number = pin + drvdata->ctrl->base; + + drvdata->pctl_dev = pinctrl_register(ctrldesc, &pdev->dev, drvdata); + if (!drvdata->pctl_dev) { + dev_err(&pdev->dev, "could not register pinctrl driver\n"); + return -EINVAL; + } + + return 0; +} + +/* register the gpiolib interface with the gpiolib subsystem */ +static int __init samsung_gpiolib_register(struct platform_device *pdev, + struct samsung_pinctrl_drv_data *drvdata) +{ + struct gpio_chip *gc; + int ret; + + gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL); + if (!gc) { + dev_err(&pdev->dev, "mem alloc for gpio_chip failed\n"); + return -ENOMEM; + } + + drvdata->gc = gc; + gc->base = drvdata->ctrl->base; + gc->ngpio = drvdata->ctrl->nr_pins; + gc->dev = &pdev->dev; + gc->set = samsung_gpio_set; + gc->get = samsung_gpio_get; + gc->label = drvdata->ctrl->label; + gc->owner = THIS_MODULE; + ret = gpiochip_add(gc); + if (ret) { + dev_err(&pdev->dev, "failed to register gpio_chip %s, error " + "code: %d\n", gc->label, ret); + return ret; + } + + return 0; +} + +static int __devinit samsung_pinctrl_probe(struct platform_device *pdev) +{ + struct samsung_pinctrl_drv_data *drvdata; + struct resource *res; + int ret; + + drvdata = (struct samsung_pinctrl_drv_data *) + platform_get_device_id(pdev)->driver_data + (pdev->id); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "cannot find IO resource\n"); + return -ENOENT; + } + + res = request_mem_region(res->start, resource_size(res), + pdev->name); + if (!res) { + dev_err(&pdev->dev, "request for mem region failed\n"); + return -EBUSY; + } + + drvdata->virt_base = ioremap(res->start, resource_size(res)); + if (!drvdata->virt_base) { + dev_err(&pdev->dev, "ioremap failed\n"); + return -EINVAL; + } + + ret = samsung_gpiolib_register(pdev, drvdata); + if (ret) + return ret; + + ret = samsung_pinctrl_register(pdev, drvdata); + if (ret) + return ret; + + platform_set_drvdata(pdev, drvdata); + return 0; +} + +/* driver data for various samsung soc's */ +#ifdef CONFIG_CPU_EXYNOS4210 + +#define EXYNOS4_PIN_BANK(offset, __gpio) \ + { \ + .reg_offset = offset, \ + .pin_base = (__gpio##_START), \ + .nr_pins = (__gpio##_NR), \ + .func_width = 4, \ + } + +/* pin banks of pin-controller 0 */ +static struct samsung_pin_bank exynos4210_pin_banks0[] = { + EXYNOS4_PIN_BANK(0x000, EXYNOS4_GPIO_A0), + EXYNOS4_PIN_BANK(0x020, EXYNOS4_GPIO_A1), + EXYNOS4_PIN_BANK(0x040, EXYNOS4_GPIO_B), + EXYNOS4_PIN_BANK(0x060, EXYNOS4_GPIO_C0), + EXYNOS4_PIN_BANK(0x080, EXYNOS4_GPIO_C1), + EXYNOS4_PIN_BANK(0x0A0, EXYNOS4_GPIO_D0), + EXYNOS4_PIN_BANK(0x0C0, EXYNOS4_GPIO_D1), + EXYNOS4_PIN_BANK(0x0E0, EXYNOS4_GPIO_E0), + EXYNOS4_PIN_BANK(0x100, EXYNOS4_GPIO_E1), + EXYNOS4_PIN_BANK(0x120, EXYNOS4_GPIO_E2), + EXYNOS4_PIN_BANK(0x140, EXYNOS4_GPIO_E3), + EXYNOS4_PIN_BANK(0x160, EXYNOS4_GPIO_E4), + EXYNOS4_PIN_BANK(0x180, EXYNOS4_GPIO_F0), + EXYNOS4_PIN_BANK(0x1A0, EXYNOS4_GPIO_F1), + EXYNOS4_PIN_BANK(0x1C0, EXYNOS4_GPIO_F2), + EXYNOS4_PIN_BANK(0x1E0, EXYNOS4_GPIO_F3), +}; + +#define EXYNOS4_PIN_BANK1(offset, __gpio) \ + { \ + .reg_offset = offset, \ + .pin_base = (__gpio##_START) - EXYNOS4_GPIO_J0_START,\ + .nr_pins = (__gpio##_NR), \ + .func_width = 4, \ + } + +/* pin banks of pin-controller 1 */ +static struct samsung_pin_bank exynos4210_pin_banks1[] = { + EXYNOS4_PIN_BANK1(0x000, EXYNOS4_GPIO_J0), + EXYNOS4_PIN_BANK1(0x020, EXYNOS4_GPIO_J1), + EXYNOS4_PIN_BANK1(0x040, EXYNOS4_GPIO_K0), + EXYNOS4_PIN_BANK1(0x060, EXYNOS4_GPIO_K1), + EXYNOS4_PIN_BANK1(0x080, EXYNOS4_GPIO_K2), + EXYNOS4_PIN_BANK1(0x0A0, EXYNOS4_GPIO_K3), + EXYNOS4_PIN_BANK1(0x0C0, EXYNOS4_GPIO_L0), + EXYNOS4_PIN_BANK1(0x0E0, EXYNOS4_GPIO_L1), + EXYNOS4_PIN_BANK1(0x100, EXYNOS4_GPIO_L2), + EXYNOS4_PIN_BANK1(0x120, EXYNOS4_GPIO_Y0), + EXYNOS4_PIN_BANK1(0x140, EXYNOS4_GPIO_Y1), + EXYNOS4_PIN_BANK1(0x160, EXYNOS4_GPIO_Y2), + EXYNOS4_PIN_BANK1(0x180, EXYNOS4_GPIO_Y3), + EXYNOS4_PIN_BANK1(0x1A0, EXYNOS4_GPIO_Y4), + EXYNOS4_PIN_BANK1(0x1C0, EXYNOS4_GPIO_Y5), + EXYNOS4_PIN_BANK1(0x1E0, EXYNOS4_GPIO_Y6), + EXYNOS4_PIN_BANK1(0xC00, EXYNOS4_GPIO_X0), + EXYNOS4_PIN_BANK1(0xC20, EXYNOS4_GPIO_X1), + EXYNOS4_PIN_BANK1(0xC40, EXYNOS4_GPIO_X2), + EXYNOS4_PIN_BANK1(0xC60, EXYNOS4_GPIO_X3), +}; + +#define EXYNOS4_PIN_BANK2(offset, __gpio) \ + { \ + .reg_offset = offset, \ + .pin_base = (__gpio##_START) - EXYNOS4_GPIO_Z_START,\ + .nr_pins = (__gpio##_NR), \ + .func_width = 4, \ + } + +/* pin banks of pin-controller 2 */ +static struct samsung_pin_bank exynos4210_pin_banks2[] = { + EXYNOS4_PIN_BANK2(0x000, EXYNOS4_GPIO_Z), +}; + +static struct samsung_pinctrl_drv_data exynos4210_pinctrl_drv_data[] = { + { + /* pin-controller instance 0 data */ + .ctrl = &(struct samsung_pin_ctrl) { + .pin_banks = exynos4210_pin_banks0, + .nr_banks = ARRAY_SIZE(exynos4210_pin_banks0), + .base = EXYNOS4_GPIO_A0_START, + .nr_pins = EXYNOS4_GPIO_J0_START - 1, + .label = "exynos4210-gpio-ctrl0", + }, + .pctl = &(struct pinctrl_desc) { + .name = "exynos4210_pinctrl", + .pctlops = &samsung_pctrl_ops, + .pmxops = &samsung_pinmux_ops, + .owner = THIS_MODULE, + }, + .pin_groups = exynos4210_pin_groups0, + .nr_groups = ARRAY_SIZE(exynos4210_pin_groups0), + .pmx_functions = exynos4210_pmx_functions0, + .nr_functions = ARRAY_SIZE(exynos4210_pmx_functions0), + }, { + /* pin-controller instance 1 data */ + .ctrl = &(struct samsung_pin_ctrl) { + .pin_banks = exynos4210_pin_banks1, + .nr_banks = ARRAY_SIZE(exynos4210_pin_banks1), + .base = EXYNOS4_GPIO_J0_START, + .nr_pins = EXYNOS4_GPIO_Z_START - + EXYNOS4_GPIO_J0_START, + .label = "exynos4210-gpio-ctrl1", + }, + .pctl = &(struct pinctrl_desc) { + .name = "exynos4210_pinctrl", + .pctlops = &samsung_pctrl_ops, + .pmxops = &samsung_pinmux_ops, + .owner = THIS_MODULE, + }, + .pin_groups = exynos4210_pin_groups1, + .nr_groups = ARRAY_SIZE(exynos4210_pin_groups1), + .pmx_functions = exynos4210_pmx_functions1, + .nr_functions = ARRAY_SIZE(exynos4210_pmx_functions1), + }, { + /* pin-controller instance 2 data */ + .ctrl = &(struct samsung_pin_ctrl) { + .pin_banks = exynos4210_pin_banks2, + .nr_banks = ARRAY_SIZE(exynos4210_pin_banks2), + .base = EXYNOS4_GPIO_Z_START, + .nr_pins = EXYNOS4_GPIO_Z_NR, + .label = "exynos4210-gpio-ctrl2", + }, + .pctl = &(struct pinctrl_desc) { + .name = "exynos4210_pinctrl", + .pctlops = &samsung_pctrl_ops, + .pmxops = &samsung_pinmux_ops, + .owner = THIS_MODULE, + }, + .pin_groups = exynos4210_pin_groups2, + .nr_groups = ARRAY_SIZE(exynos4210_pin_groups2), + .pmx_functions = exynos4210_pmx_functions2, + .nr_functions = ARRAY_SIZE(exynos4210_pmx_functions2), + }, +}; +#define EXYNOS4210_PCTRL_DRVDATA ((kernel_ulong_t)&exynos4210_pinctrl_drv_data) +#else +#define EXYNOS4210_PCTRL_DRVDATA (kernel_ulong_t)NULL +#endif /* CONFIG_CPU_EXYNOS4210 */ + +static struct platform_device_id samsung_pinctrl_driver_ids[] = { + { + .name = "exynos4-pinctrl", + .driver_data = EXYNOS4210_PCTRL_DRVDATA, + }, +}; + +static struct platform_driver samsung_pinctrl_driver = { + .probe = samsung_pinctrl_probe, + .id_table = samsung_pinctrl_driver_ids, + .driver = { + .name = "samsung-pinctrl", + .owner = THIS_MODULE, + }, +}; + +static int __init samsung_pinctrl_drv_register(void) +{ + return platform_driver_register(&samsung_pinctrl_driver); +} +postcore_initcall(samsung_pinctrl_drv_register); -- 1.6.6.rc2

14 years

Linaro Kernel November 2011 Release

by Deepak Saxena

The Linaro Kernel Working Group (KWG) is excited to announce the availability our October 2011 development snapshot: linux-linaro-3.1-2011.11-1 As the word "snapshot" implies, these are meant as development kernels and have not been fully validated. You should expect issues and to help us deliver a better kernel in the future, please file bugs in Launchpad at https://bugs.launchpad.net/linux-linaro. The source tarball is available at: http://launchpad.net/linux-linaro/3.1/3.1-2011.11/+download/linux-linaro-3.… The kernel sources can also be accessed using git at: git://git.linaro.org/kernel/linux-linaro-3.1.git tag: linux-linaro-3.1-2011.11-0 This kernel includes the following changes from the 2011.10 kernel: - The v3.1.1 stable kernel - LPAE support from Catalin Marinas - Samsung cpuidle work from Amit Kachhap - sched_mc optimization from Vincent Guittot - Fix for mmap greater than 2GB from Rob Herring A full change log against the 2011.09 release is available at: http://launchpad.net/linux-linaro/3.1/3.1-2011.11/+download/CHANGELOG-linux… High Priority Known Issues: - None at this time This month's release is about a week early due to the upcoming Thanksgiving holidays in the US. If we find any major issues in the next few days, we will spin a new tarball. Mailing list: http://lists.linaro.org/mailman/listinfo/linaro-dev Questions? https://ask.linaro.org/

14 years

[ACTIVITY] (Deepak Saxena) Nov 6-12

by Deepak Saxena

=== Highlights === * Wrote post for Linaro blog summarizing Linaro connect (http://www.linaro.org/linaro-blog/2011/11/09/kernel-working-group-a-linaro-…) * Started transferring new roadmap cards to launchpad blueprints * Started work on documenting proposed new kernel process * Working with Ohad upstream to understand status of rpmsg and what === Plans === * Finish writing up new kernel process * Release 11.11 kernel * Finish creating new blueprints * Work with Mounir on cleaning out old blueprints from 11.05 and 11.11 cycle * Find all my receipts and do expenses for ELC + LC * Create new roadmap cards === Travel/Time Off === * Tentatively taking next wed (11/23) off * Linaro holiday: Dec 26 - Jan 2

14 years

ACTIVITY (Rajendra Nayak) Oct 31 - Nov 4

by Rajendra Nayak

== Rajendra Nayak <rnayak> == === Highlights === * Regulator core DT patches Acked by Mark. Some more minor comments from Olof, will need another final repost. * Initial omap hsmmc dt patches posted. Need more rework in cleaning up some of the legacy code from driver. * Mcspi/Ethernet dt patches validated, but with hack to make gpio_to_irq() work. Will post with proper implementation once Benoit fixes up the omap gpio adaptations. * Working on serial dt conversion, on top of the runtime changes /cleanup underway for omap serial driver. === Plans === * Repost regulator core binding series. * Rework/repost driver dt adaptations for omap mmc/serial/mcspi/eth * Start on pinmux driver for OMAP as communicated via Rypple. Tony Lindgren had plans of doing this, so need to syncup with him before I start off. * Work on basic OMAP5 support (test on emulator/simulator) using DT.

14 years

[Activity] (Niklas Hernaeus) 2011-11-07 - 2011-11-13

by Niklas Hernaeus

== Niklas Hernaeus <nhe> == === General activity === * Prepared report of Linaro Connect for STE Competence group, security. To be held Monday 2011-11-14. * Preparing DT report for Knowledge sharing session. 20% done. * Preparing a Linaro collaboration tools session. (irc, mumble, etherpad, blueprints, rypple) 20% done. Date and form not set. * Sent out a lurking patch from Linus. Consequences not fully understood. * Found some issues with done dt support for uarts. Probably just need a kernel rebase. === Plans === * Make detailed plans for the work items. * Present Linaro Connect report for STE Competence group. * Make the dt uarts work again. * Start work on dt i2c. * Also, MMC must be included in the blueprints, somewhere at the top, below i2c.

14 years

[ACTIVITY] (Shawn Guo) Week of Nov 7

by Shawn Guo

=== Device Tree === * imx5 board level DT series hit v3.2-rc1. * imx6 with DT support from the beginning hit v3.2-rc1. * Migrated mc13892 regulator to DT based Rajendra's series v4. Waiting for his series v5 to rebase and post mine. === Consolidation and cleanup === * Handed over imx pinctrl work to Dong Aisheng who has been assigned to pinctrl group for this work. And suggested we start from imx6 which needs pinctrl support badly. (imx6 becomes the priority for Freescale Landing Team) * Migrated imx6 clock to Mike's common clock series v2. Waiting for his series v3 to rebase and post my mine. * Sent a patch to remove imx_idle hook and use pm_idle instead to get imx arch_idle prepared for the global arch_idle cleanup coming later (suggested by Russell). === Misc === * Tested imx6 and mxs on v3.2-rc1. Collected a few fixing patches for v3.2-rc2. * Sent a patch to fix imx6 mmc error seen when mounting rootfs on SD/MMC card (reported by Dirk from Bosch). That is a temporary solution, and the issue should be eventually resolved by pinctrl support in a nice way. * Reported a v3.2-rc1 kernel issue. With CONFIG_PROVE_LOCKING enabled, a circular locking dependency warning is seen on both imx6 and imx5 with Linaro rootfs (nano, developer). === Plan === * Post mc13892 regulator DT patches * Post imx6 common clock patches * Look into Grant's clock DT bindings and try to play it with imx6 common clock support -- Regards, Shawn

14 years

[ACTIVITY] (Thomas Abraham) 2011-11-07 - 2011-11-12

by Thomas Abraham

== Thomas Abraham <thomas-ab> == === Highlights === * Reviewed pinctrl driver and pinmux extensions. Completed a limited functionality driver for exynos4, will submit this for review. * Reviewed LinusW's pin configuration patch and checked compatibility for exynos4. === Plans === * Develop a complete pinctrl driver with all possible pinmux support. * Complete the device tree support for i2s driver.

14 years

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

linaro-kernel