OPP core supports frequency/voltage changes based on the target frequency now, use that instead of open coding the same in cpufreq-dt driver.
Signed-off-by: Viresh Kumar viresh.kumar@linaro.org Reviewed-by: Stephen Boyd sboyd@codeaurora.org --- drivers/cpufreq/cpufreq-dt.c | 73 ++------------------------------------------ 1 file changed, 2 insertions(+), 71 deletions(-)
diff --git a/drivers/cpufreq/cpufreq-dt.c b/drivers/cpufreq/cpufreq-dt.c index 6f80ce56b4ec..150a172c7d0a 100644 --- a/drivers/cpufreq/cpufreq-dt.c +++ b/drivers/cpufreq/cpufreq-dt.c @@ -45,79 +45,10 @@ static struct freq_attr *cpufreq_dt_attr[] = {
static int set_target(struct cpufreq_policy *policy, unsigned int index) { - struct dev_pm_opp *opp; - struct cpufreq_frequency_table *freq_table = policy->freq_table; - struct clk *cpu_clk = policy->clk; struct private_data *priv = policy->driver_data; - struct device *cpu_dev = priv->cpu_dev; - struct regulator *cpu_reg = priv->cpu_reg; - unsigned long volt = 0, tol = 0; - int volt_old = 0; - unsigned int old_freq, new_freq; - long freq_Hz, freq_exact; - int ret; - - freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000); - if (freq_Hz <= 0) - freq_Hz = freq_table[index].frequency * 1000; - - freq_exact = freq_Hz; - new_freq = freq_Hz / 1000; - old_freq = clk_get_rate(cpu_clk) / 1000; - - if (!IS_ERR(cpu_reg)) { - unsigned long opp_freq; - - rcu_read_lock(); - opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_Hz); - if (IS_ERR(opp)) { - rcu_read_unlock(); - dev_err(cpu_dev, "failed to find OPP for %ld\n", - freq_Hz); - return PTR_ERR(opp); - } - volt = dev_pm_opp_get_voltage(opp); - opp_freq = dev_pm_opp_get_freq(opp); - rcu_read_unlock(); - tol = volt * priv->voltage_tolerance / 100; - volt_old = regulator_get_voltage(cpu_reg); - dev_dbg(cpu_dev, "Found OPP: %ld kHz, %ld uV\n", - opp_freq / 1000, volt); - } - - dev_dbg(cpu_dev, "%u MHz, %d mV --> %u MHz, %ld mV\n", - old_freq / 1000, (volt_old > 0) ? volt_old / 1000 : -1, - new_freq / 1000, volt ? volt / 1000 : -1); - - /* scaling up? scale voltage before frequency */ - if (!IS_ERR(cpu_reg) && new_freq > old_freq) { - ret = regulator_set_voltage_tol(cpu_reg, volt, tol); - if (ret) { - dev_err(cpu_dev, "failed to scale voltage up: %d\n", - ret); - return ret; - } - } - - ret = clk_set_rate(cpu_clk, freq_exact); - if (ret) { - dev_err(cpu_dev, "failed to set clock rate: %d\n", ret); - if (!IS_ERR(cpu_reg) && volt_old > 0) - regulator_set_voltage_tol(cpu_reg, volt_old, tol); - return ret; - }
- /* scaling down? scale voltage after frequency */ - if (!IS_ERR(cpu_reg) && new_freq < old_freq) { - ret = regulator_set_voltage_tol(cpu_reg, volt, tol); - if (ret) { - dev_err(cpu_dev, "failed to scale voltage down: %d\n", - ret); - clk_set_rate(cpu_clk, old_freq * 1000); - } - } - - return ret; + return dev_pm_opp_set_rate(priv->cpu_dev, + policy->freq_table[index].frequency * 1000); }
/*