ARM64 JIT used FP (x29) as eBPF fp register, but FP is subjected to change during function call so it may cause the BPF prog stack base address change too. Whenever, it pointed to the bottom of BPF prog stack instead of the top.

So, when copying data via bpf_probe_read, it will be copied to (SP - offset), then it may overwrite the saved FP/LR.

Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee saved register, so it will keep intact during function call. It is initialized in BPF prog prologue when BPF prog is started to run everytime. When BPF prog exits, it could be just tossed.

Other than this the BPf prog stack base need to be setup before function call stack.

So, the BPF stack layout looks like:

high original A64_SP => 0:+-----+ BPF prologue | | FP/LR and callee saved registers BPF fp register => +64:+-----+ | | | ... | BPF prog stack | | | | current A64_SP => +-----+ | | | ... | Function call stack | | +-----+ low

Signed-off-by: Yang Shi yang.shi@linaro.org CC: Zi Shen Lim zlim.lnx@gmail.com CC: Xi Wang xi.wang@gmail.com --- arch/arm64/net/bpf_jit_comp.c | 38 +++++++++++++++++++++++++++++++------- 1 file changed, 31 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/net/bpf_jit_comp.c b/arch/arm64/net/bpf_jit_comp.c index a44e529..6809647 100644 --- a/arch/arm64/net/bpf_jit_comp.c +++ b/arch/arm64/net/bpf_jit_comp.c @@ -50,7 +50,7 @@ static const int bpf2a64[] = { [BPF_REG_8] = A64_R(21), [BPF_REG_9] = A64_R(22), /* read-only frame pointer to access stack */ - [BPF_REG_FP] = A64_FP, + [BPF_REG_FP] = A64_R(25), /* temporary register for internal BPF JIT */ [TMP_REG_1] = A64_R(23), [TMP_REG_2] = A64_R(24), @@ -155,18 +155,42 @@ static void build_prologue(struct jit_ctx *ctx) stack_size += 4; /* extra for skb_copy_bits buffer */ stack_size = STACK_ALIGN(stack_size);

+ /* + * BPF prog stack layout + * + * high + * original A64_SP => 0:+-----+ BPF prologue + * | | FP/LR and callee saved registers + * BPF fp register => +64:+-----+ + * | | + * | ... | BPF prog stack + * | | + * | | + * current A64_SP => +-----+ + * | | + * | ... | Function call stack + * | | + * +-----+ + * low + * + */ + + /* Save FP and LR registers to stay align with ARM64 AAPCS */ + emit(A64_PUSH(A64_FP, A64_LR, A64_SP), ctx); + /* Save callee-saved register */ emit(A64_PUSH(r6, r7, A64_SP), ctx); emit(A64_PUSH(r8, r9, A64_SP), ctx); if (ctx->tmp_used) emit(A64_PUSH(tmp1, tmp2, A64_SP), ctx);

- /* Set up BPF stack */ - emit(A64_SUB_I(1, A64_SP, A64_SP, stack_size), ctx); - - /* Set up frame pointer */ + /* Set up BPF prog stack base register (x25) */ emit(A64_MOV(1, fp, A64_SP), ctx);

+ /* Set up function call stack */ + emit(A64_SUB_I(1, A64_SP, A64_SP, stack_size), ctx); + emit(A64_MOV(1, A64_FP, A64_SP), ctx); + /* Clear registers A and X */ emit_a64_mov_i64(ra, 0, ctx); emit_a64_mov_i64(rx, 0, ctx); @@ -196,8 +220,8 @@ static void build_epilogue(struct jit_ctx *ctx) emit(A64_POP(r8, r9, A64_SP), ctx); emit(A64_POP(r6, r7, A64_SP), ctx);

- /* Restore frame pointer */ - emit(A64_MOV(1, fp, A64_SP), ctx); + /* Restore FP/LR registers */ + emit(A64_POP(A64_FP, A64_LR, A64_SP), ctx);

/* Set return value */ emit(A64_MOV(1, A64_R(0), r0), ctx);