arm-soc boot: 37 pass, 6 fail (v3.14-rc4-693-g10c9e4a) - linaro-kernel

9 Mar 2014


      Automated DT boot report for various ARM defconfigs.
Tree/Branch: arm-soc
Git describe: v3.14-rc4-693-g10c9e4a
Failed boot tests (console logs at the end)
===========================================
       sun7i-a20-cubieboard2:     FAIL:    multi_lpae_defconfig
       sun7i-a20-cubieboard2:     FAIL:    sunxi_defconfig
        sun4i-a10-cubieboard:     FAIL:    sunxi_defconfig
                ste-snowball:     FAIL:    multi_v7_defconfig
       sun7i-a20-cubieboard2:     FAIL:    multi_v7_defconfig
        sun4i-a10-cubieboard:     FAIL:    multi_v7_defconfig
Full Report
===========
da8xx_omapl_defconfig
---------------------
                   da850-evm     PASS:    0 min 15.2 sec
omap2plus_defconfig
-------------------
               legacy,3730xm     PASS:    0 min 51.8 sec
            am335x-boneblack     PASS:    0 min 25.5 sec
             omap3-beagle-xm     PASS:    1 min  3.3 sec
           legacy,3530beagle     PASS:    0 min 50.8 sec
                 omap4-panda     PASS:    1 min  8.6 sec
            omap3-overo-tobi     PASS:    0 min 22.7 sec
                 am335x-bone     PASS:    0 min 32.3 sec
      omap3-overo-storm-tobi     PASS:    0 min 22.2 sec
              omap4-panda-es     PASS:    1 min 10.1 sec
            legacy,3730storm     PASS:    0 min 23.5 sec
            legacy,3530overo     PASS:    0 min 21.1 sec
multi_lpae_defconfig
--------------------
       sun7i-a20-cubieboard2     FAIL:    0 min 19.6 sec
tegra_defconfig
---------------
              tegra30-beaver     PASS:    0 min 17.1 sec
imx_v6_v7_defconfig
-------------------
  imx6dl-wandboard,wand-dual     PASS:    0 min 18.5 sec
  imx6dl-wandboard,wand-solo     PASS:    0 min 18.4 sec
             imx6q-wandboard     PASS:    0 min 16.9 sec
sunxi_defconfig
---------------
       sun7i-a20-cubieboard2     FAIL:    0 min 17.6 sec
        sun4i-a10-cubieboard     FAIL:    0 min 20.4 sec
bcm_defconfig
-------------
                 bcm28155-ap     PASS:    0 min 58.8 sec
mvebu_v7_defconfig
------------------
  armada-xp-openblocks-ax3-4     PASS:    0 min 22.2 sec
          armada-370-mirabox     PASS:    0 min 20.4 sec
exynos_defconfig
----------------
          exynos5250-arndale     PASS:    0 min 30.0 sec
multi_v7_defconfig
------------------
                ste-snowball     FAIL:    0 min 30.4 sec
              tegra30-beaver     PASS:    0 min 19.9 sec
            am335x-boneblack     PASS:    0 min 23.6 sec
             omap3-beagle-xm     PASS:    0 min 55.4 sec
       sun7i-a20-cubieboard2     FAIL:    0 min 31.4 sec
          armada-370-mirabox     PASS:    0 min 22.4 sec
                 omap4-panda     PASS:    0 min 51.6 sec
  armada-xp-openblocks-ax3-4     PASS:    0 min 24.9 sec
        sun4i-a10-cubieboard     FAIL:    0 min 19.4 sec
                 bcm28155-ap     PASS:    1 min  9.5 sec
            omap3-overo-tobi     PASS:    0 min 22.3 sec
  imx6dl-wandboard,wand-solo     PASS:    0 min 17.9 sec
                 am335x-bone     PASS:    0 min 26.3 sec
      omap3-overo-storm-tobi     PASS:    0 min 24.1 sec
             imx6q-wandboard     PASS:    0 min 16.9 sec
              omap4-panda-es     PASS:    0 min 53.0 sec
  imx6dl-wandboard,wand-dual     PASS:    0 min 17.9 sec
u8500_defconfig
---------------
                ste-snowball     PASS:    0 min 30.4 sec
sama5_defconfig
---------------
                  sama5d35ek     PASS:    0 min 17.0 sec
davinci_all_defconfig
---------------------
             legacy,dm365evm     PASS:    0 min 16.5 sec
Console logs for failures
=========================
multi_lpae_defconfig
--------------------
sun7i-a20-cubieboard2: FAIL: last 80 lines of boot log:
    -------------------------------------------------------
setenv ethaddr 22:71:81:DA:53:EA
sun7i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
sun7i#setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
 setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
sun7i# setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
sun7i# if test -n ${initenv}; then run initenv; fi
if test -n ${initenv}; then run initenv; fi
sun7i# if test -n ${preboot}; then run preboot; fi
if test -n ${preboot}; then run preboot; fi
sun7i# setenv autoload no; setenv autoboot no
setenv autoload no; setenv autoboot no
sun7i# dhcp
dhcp
ENET Speed is 100 Mbps - FULL duplex connection
BOOTP broadcast 1
DHCP client bound to address 192.168.1.153
sun7i# setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
sun7i# if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
sun7i# tftp 0x40008000 192.168.1.2:tmp/cubie2-ZBzmaD/zImage
tftp 0x40008000 192.168.1.2:tmp/cubie2-ZBzmaD/zImage
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'tmp/cubie2-ZBzmaD/zImage'.
Load address: 0x40008000
Loading: *#################################################################
     #################################################################
     #################################################################
     #################################################################
     ##################################################
     2.7 MiB/s
done
Bytes transferred = 4544360 (455768 hex)
sun7i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'buildroot.cpio.gz.uboot'.
Load address: 0x42000000
Loading: *############################################
     2.7 MiB/s
done
Bytes transferred = 642602 (9ce2a hex)
sun7i# tftp 0x41000000 192.168.1.2:tmp/cubie2-ZBzmaD/sun7i-a20-cubieboard2.dtb
tftp 0x41000000 192.168.1.2:tmp/cubie2-ZBzmaD/sun7i-a20-cubieboard2.dtb
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'tmp/cubie2-ZBzmaD/sun7i-a20-cubieboard2.dtb'.
Load address: 0x41000000
Loading: *##
     2.1 MiB/s
done
Bytes transferred = 15599 (3cef hex)
sun7i# printenv bootargs
printenv bootargs
bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.153:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none
sun7i# bootz 0x40008000 0x42000000 0x41000000
bootz 0x40008000 0x42000000 0x41000000
Kernel image @ 0x40008000 [ 0x000000 - 0x455768 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   
   Created:      2014-02-07  19:37:29 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    642538 Bytes = 627.5 KiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 40ff9000, end 40fffcee ... OK
Starting kernel ...
~$off
# PYBOOT: Exception: kernel: ERROR: did not start booting.
# PYBOOT: Time: 19.56 seconds.
# PYBOOT: Result: FAIL
sunxi_defconfig
---------------
sun7i-a20-cubieboard2: FAIL: last 80 lines of boot log:
    -------------------------------------------------------
arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.2-1ubuntu1) 4.7.2
GNU ld (GNU Binutils for Ubuntu) 2.22.90.20120919
sun7i# setenv ethaddr 22:71:81:DA:53:EA
setenv ethaddr 22:71:81:DA:53:EA
sun7i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
sun7i# setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
sun7i# setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
sun7i# if test -n ${initenv}; then run initenv; fi
if test -n ${initenv}; then run initenv; fi
sun7i# if test -n ${preboot}; then run preboot; fi
if test -n ${preboot}; then run preboot; fi
sun7i# setenv autoload no; setenv autoboot no
setenv autoload no; setenv autoboot no
sun7i#dhcp
 dhcp
ENET Speed is 100 Mbps - FULL duplex connection
BOOTP broadcast 1
DHCP client bound to address 192.168.1.153
sun7i# setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
sun7i# if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
sun7i#tftp 0x40008000 192.168.1.2:tmp/cubie2-i1AOp4/zImage
 tftp 0x40008000 192.168.1.2:tmp/cubie2-i1AOp4/zImage
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'tmp/cubie2-i1AOp4/zImage'.
Load address: 0x40008000
Loading: *#################################################################
     ########################################################
     2.7 MiB/s
done
Bytes transferred = 1774352 (1b1310 hex)
sun7i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'buildroot.cpio.gz.uboot'.
Load address: 0x42000000
Loading: *############################################
     2.7 MiB/s
done
Bytes transferred = 642602 (9ce2a hex)
sun7i# tftp 0x41000000 192.168.1.2:tmp/cubie2-i1AOp4/sun7i-a20-cubieboard2.dtb
tftp 0x41000000 192.168.1.2:tmp/cubie2-i1AOp4/sun7i-a20-cubieboard2.dtb
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.153
Filename 'tmp/cubie2-i1AOp4/sun7i-a20-cubieboard2.dtb'.
Load address: 0x41000000
Loading: *##
     2.1 MiB/s
done
Bytes transferred = 15599 (3cef hex)
sun7i# printenv bootargs
printenv bootargs
bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.153:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none
sun7i# bootz 0x40008000 0x42000000 0x41000000
bootz 0x40008000 0x42000000 0x41000000
Kernel image @ 0x40008000 [ 0x000000 - 0x1b1310 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   
   Created:      2014-02-07  19:37:29 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    642538 Bytes = 627.5 KiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 40ff9000, end 40fffcee ... OK
Starting kernel ...
~$off
# PYBOOT: Exception: kernel: ERROR: did not start booting.
# PYBOOT: Time: 17.61 seconds.
# PYBOOT: Result: FAIL
sun4i-a10-cubieboard: FAIL: last 80 lines of boot log:
    ------------------------------------------------------
GNU ld (GNU Binutils for Ubuntu) 2.22.90.20120919
sun4i# setenv ethaddr 2e:40:70:f0:12:08
setenv ethaddr 2e:40:70:f0:12:08
sun4i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
sun4i# setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
sun4i# setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
sun4i# if test -n ${initenv}; then run initenv; fi
if test -n ${initenv}; then run initenv; fi
sun4i# if test -n ${preboot}; then run preboot; fi
if test -n ${preboot}; then run preboot; fi
sun4i# setenv autoload no; setenv autoboot no
setenv autoload no; setenv autoboot no
sun4i# dhcp
dhcp
ENET Speed is 100 Mbps - FULL duplex connection
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.1.193
sun4i# setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
sun4i# if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
sun4i# tftp 0x40008000 192.168.1.2:tmp/cubie-OmVeqF/zImage
tftp 0x40008000 192.168.1.2:tmp/cubie-OmVeqF/zImage
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'tmp/cubie-OmVeqF/zImage'.
Load address: 0x40008000
Loading: *#################################################################
     ########################################################
     2.7 MiB/s
done
Bytes transferred = 1774352 (1b1310 hex)
sun4i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'buildroot.cpio.gz.uboot'.
Load address: 0x42000000
Loading: *############################################
     2.7 MiB/s
done
Bytes transferred = 642602 (9ce2a hex)
sun4i#tftp 0x41000000 192.168.1.2:tmp/cubie-OmVeqF/sun4i-a10-cubieboard.dtb
 tftp 0x41000000 192.168.1.2:tmp/cubie-OmVeqF/sun4i-a10-cubieboard.dtb
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'tmp/cubie-OmVeqF/sun4i-a10-cubieboard.dtb'.
Load address: 0x41000000
Loading: *#
     2 MiB/s
done
Bytes transferred = 12602 (313a hex)
sun4i#printenv bootargs
 printenv bootargs
bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.193:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none
sun4i# bootz 0x40008000 0x42000000 0x41000000
bootz 0x40008000 0x42000000 0x41000000
Kernel image @ 0x40008000 [ 0x000000 - 0x1b1310 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   
   Created:      2014-02-07  19:37:29 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    642538 Bytes = 627.5 KiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 40ff9000, end 40fff139 ... OK
Starting kernel ...
~$off
# PYBOOT: Exception: kernel: ERROR: did not start booting.
# PYBOOT: Time: 20.40 seconds.
# PYBOOT: Result: FAIL
multi_v7_defconfig
------------------
ste-snowball: FAIL: last 80 lines of boot log:
    ----------------------------------------------
Command(snowball console)> hardreset
(user:khilman) Reboot snowball
Reboot: snowball ; ip9258 2 2 :  ('off', 6, 'on')
, sleep 6,
MCDE:  startup failed
sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2
EMMC: 0, MMC: 1
In:    serial
Out:   serial
Err:   serial
Net:   smc911x-0
Hit any key to stop autoboot:  1  
0
U8500 $ 
U8500 $ version
U8500 $ versionsetenv ethaddr 6e:e6:84:36:8e:9e
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
U8500 $ setenv ethaddr 6e:e6:84:36:8e:9esetenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4
Can't overwrite "ethaddr"
U8500 $ setenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
U8500 $ setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'if test -n ${initenv}; then run initenv; fi
U8500 $ if test -n ${initenv}; then run initenv; fiif test -n ${preboot}; then run preboot; fi
U8500 $ if test -n ${preboot}; then run preboot; fisetenv autoload no; setenv autoboot no
U8500 $ setenv autoload no; setenv autoboot nodhcp
U8500 $ dhcp
smc911x: detected LAN9221 controller
smc911x: phy initialized
smc911x: MAC 6e:e6:84:36:8e:9e
BOOTP broadcast 1
DHCP client bound to address 192.168.1.159
U8500 $ setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
U8500 $ if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
U8500 $ tftp 0x00800000 192.168.1.2:tmp/snowball-fTqJ8A/tmpyEWGyK-uImage
tftp 0x00800000 192.168.1.2:tmp/snowball-fTqJ8A/tmpyEWGyK-uImage
smc911x: detected LAN9221 controller
smc911x: phy initialized
smc911x: MAC 6e:e6:84:36:8e:9e
Using smc911x-0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.159
Filename 'tmp/snowball-fTqJ8A/tmpyEWGyK-uImage'.
Load address: 0x800000
Loading: *#################################################################
     #################################################################
     #################################################################
     #################################################################
     ###################################################
done
Bytes transferred = 4559705 (459359 hex)
U8500 $ printenv bootargs
printenv bootargs
bootargs=console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none
U8500 $ bootm 0x00800000  
bootm 0x00800000  
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4559641 Bytes =  4.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Loading Kernel Image ... OK
OK
Starting kernel ...
~$off
# PYBOOT: Exception: kernel: ERROR: did not start booting.
# PYBOOT: Time: 30.39 seconds.
# PYBOOT: Result: FAIL
sun7i-a20-cubieboard2: FAIL: last 80 lines of boot log:
    -------------------------------------------------------
Connected to cubie2 console [channel connected] (~$quit to exit)
(user:khilman) is already connected
~$hardreset
Command(cubie2 console)> hardreset
(user:khilman) Reboot cubie2
Reboot: cubie2 ; phidget 3 0 :  off, sleep, on
 0 
sun7i# ~$off
# PYBOOT: Exception: ERROR: Could not break into autoboot.
# PYBOOT: Time: 31.39 seconds.
# PYBOOT: Result: FAIL
sun4i-a10-cubieboard: FAIL: last 80 lines of boot log:
    ------------------------------------------------------
setenv ethaddr 2e:40:70:f0:12:08
sun4i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4
sun4i#setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
 setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'
sun4i# setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
sun4i# if test -n ${initenv}; then run initenv; fi
if test -n ${initenv}; then run initenv; fi
sun4i# if test -n ${preboot}; then run preboot; fi
if test -n ${preboot}; then run preboot; fi
sun4i# setenv autoload no; setenv autoboot no
setenv autoload no; setenv autoboot no
sun4i# dhcp
dhcp
ENET Speed is 100 Mbps - FULL duplex connection
BOOTP broadcast 1
DHCP client bound to address 192.168.1.193
sun4i#setenv serverip 192.168.1.2
 setenv serverip 192.168.1.2
sun4i# if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
sun4i# tftp 0x40008000 192.168.1.2:tmp/cubie-u_8MjA/zImage
tftp 0x40008000 192.168.1.2:tmp/cubie-u_8MjA/zImage
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'tmp/cubie-u_8MjA/zImage'.
Load address: 0x40008000
Loading: *#################################################################
     #################################################################
     #################################################################
     #################################################################
     ################################################
     2.7 MiB/s
done
Bytes transferred = 4518392 (44f1f8 hex)
sun4i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'buildroot.cpio.gz.uboot'.
Load address: 0x42000000
Loading: *############################################
     2.7 MiB/s
done
Bytes transferred = 642602 (9ce2a hex)
sun4i#tftp 0x41000000 192.168.1.2:tmp/cubie-u_8MjA/sun4i-a10-cubieboard.dtb
 tftp 0x41000000 192.168.1.2:tmp/cubie-u_8MjA/sun4i-a10-cubieboard.dtb
Using emac device
TFTP from server 192.168.1.2; our IP address is 192.168.1.193
Filename 'tmp/cubie-u_8MjA/sun4i-a10-cubieboard.dtb'.
Load address: 0x41000000
Loading: *#
     2.4 MiB/s
done
Bytes transferred = 12602 (313a hex)
sun4i# printenv bootargs
printenv bootargs
bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.193:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none
sun4i# bootz 0x40008000 0x42000000 0x41000000
bootz 0x40008000 0x42000000 0x41000000
Kernel image @ 0x40008000 [ 0x000000 - 0x44f1f8 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   
   Created:      2014-02-07  19:37:29 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    642538 Bytes = 627.5 KiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 41000000
   Booting using the fdt blob at 0x41000000
   Loading Device Tree to 40ff9000, end 40fff139 ... OK
Starting kernel ...
~$off
# PYBOOT: Exception: kernel: ERROR: did not start booting.
# PYBOOT: Time: 19.42 seconds.
# PYBOOT: Result: FAIL