May 2025 - Linux-stable-mirror

[PATCH v3 0/2] iio: accel: fxls8962af: Fix temperature readings

by Sean Nyekjaer

Add the correct scale to get temperature in mili degree Celcius. Add sign component to temperature scan element. Signed-off-by: Sean Nyekjaer <sean(a)geanix.com> --- Changes in v3: - Dropping define infavor of inline scale value - Added using constants from units.h - Tweaked commit msg to make it more assertive - Link to v2: https://lore.kernel.org/r/20250502-fxls-v2-0-e1af65f1aa6c@geanix.com Changes in v2: - Correct offset is applied before scaling component - Added sign component to temperature scan element - Link to v1: https://lore.kernel.org/r/20250501-fxls-v1-1-f54061a07099@geanix.com --- Sean Nyekjaer (2): iio: accel: fxls8962af: Fix temperature calculation iio: accel: fxls8962af: Fix temperature scan element sign drivers/iio/accel/fxls8962af-core.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) --- base-commit: 609bc31eca06c7408e6860d8b46311ebe45c1fef change-id: 20250501-fxls-307ef3d6d065 Best regards, -- Sean Nyekjaer <sean(a)geanix.com>

4 months, 2 weeks

2
4
0 0

[PATCH v2] video: screen_info: Relocate framebuffers behind PCI bridges

by Thomas Zimmermann

Apply bridge window offsets to screen_info framebuffers during relocation. Fixes invalid access to I/O memory. Resources behind a PCI bridge can be located at a certain offset in the kernel's I/O range. The framebuffer memory range stored in screen_info refers to the offset as seen during boot (essentialy 0). During boot up, the kernel may assign a different memory offset to the bridge device and thereby relocating the framebuffer address of the PCI graphics device as seen by the kernel. The information in screen_info must be updated as well. The helper pcibios_bus_to_resource() performs the relocation of the screen_info resource. The result now matches the I/O-memory resource of the PCI graphics device. As before, we store away the information necessary to update the information in screen_info. Commit 78aa89d1dfba ("firmware/sysfb: Update screen_info for relocated EFI framebuffers") added the code for updating screen_info. It is based on similar functionality that pre-existed in efifb. Efifb uses a pointer to the PCI resource, while the newer code does a memcpy of the region. Hence efifb sees any updates to the PCI resource and avoids the issue. v2: - Fixed tags (Takashi, Ivan) - Updated information on efifb Signed-off-by: Thomas Zimmermann <tzimmermann(a)suse.de> Reported-by: "Ivan T. Ivanov" <iivanov(a)suse.de> Closes: https://bugzilla.suse.com/show_bug.cgi?id=1240696 Tested-by: "Ivan T. Ivanov" <iivanov(a)suse.de> Fixes: 78aa89d1dfba ("firmware/sysfb: Update screen_info for relocated EFI framebuffers") Cc: dri-devel(a)lists.freedesktop.org Cc: <stable(a)vger.kernel.org> # v6.9+ --- drivers/video/screen_info_pci.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) diff --git a/drivers/video/screen_info_pci.c b/drivers/video/screen_info_pci.c index 6c5833517141..c46c75dc3fae 100644 --- a/drivers/video/screen_info_pci.c +++ b/drivers/video/screen_info_pci.c @@ -8,7 +8,7 @@ static struct pci_dev *screen_info_lfb_pdev; static size_t screen_info_lfb_bar; static resource_size_t screen_info_lfb_offset; -static struct resource screen_info_lfb_res = DEFINE_RES_MEM(0, 0); +static struct pci_bus_region screen_info_lfb_region; static bool __screen_info_relocation_is_valid(const struct screen_info *si, struct resource *pr) { @@ -31,7 +31,7 @@ void screen_info_apply_fixups(void) if (screen_info_lfb_pdev) { struct resource *pr = &screen_info_lfb_pdev->resource[screen_info_lfb_bar]; - if (pr->start != screen_info_lfb_res.start) { + if (pr->start != screen_info_lfb_region.start) { if (__screen_info_relocation_is_valid(si, pr)) { /* * Only update base if we have an actual @@ -69,10 +69,21 @@ static void screen_info_fixup_lfb(struct pci_dev *pdev) for (i = 0; i < numres; ++i) { struct resource *r = &res[i]; + struct pci_bus_region bus_region = { + .start = r->start, + .end = r->end, + }; const struct resource *pr; if (!(r->flags & IORESOURCE_MEM)) continue; + + /* + * Translate the address to resource if the framebuffer + * is behind a PCI bridge. + */ + pcibios_bus_to_resource(pdev->bus, r, &bus_region); + pr = pci_find_resource(pdev, r); if (!pr) continue; @@ -85,7 +96,7 @@ static void screen_info_fixup_lfb(struct pci_dev *pdev) screen_info_lfb_pdev = pdev; screen_info_lfb_bar = pr - pdev->resource; screen_info_lfb_offset = r->start - pr->start; - memcpy(&screen_info_lfb_res, r, sizeof(screen_info_lfb_res)); + memcpy(&screen_info_lfb_region, &bus_region, sizeof(screen_info_lfb_region)); } } DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_ANY_ID, PCI_ANY_ID, PCI_BASE_CLASS_DISPLAY, 16, -- 2.49.0

4 months, 2 weeks

2
3
0 0

[PATCH 2/5] rust: clean Rust 1.87.0's `clippy::ptr_eq` lints

by Miguel Ojeda

Starting with Rust 1.87.0 (expected 2025-05-15) [1], Clippy may expand the `ptr_eq` lint, e.g.: error: use `core::ptr::eq` when comparing raw pointers --> rust/kernel/list.rs:438:12 | 438 | if self.first == item { | ^^^^^^^^^^^^^^^^^^ help: try: `core::ptr::eq(self.first, item)` | = help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#ptr_eq = note: `-D clippy::ptr-eq` implied by `-D warnings` = help: to override `-D warnings` add `#[allow(clippy::ptr_eq)]` Thus clean the few cases we have. This patch may not be actually needed by the time Rust 1.87.0 releases since a PR to relax the lint has been beta nominated [2] due to reports of being too eager (at least by default) [3]. Cc: stable(a)vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs). Link: https://github.com/rust-lang/rust-clippy/pull/14339 [1] Link: https://github.com/rust-lang/rust-clippy/pull/14526 [2] Link: https://github.com/rust-lang/rust-clippy/issues/14525 [3] Signed-off-by: Miguel Ojeda <ojeda(a)kernel.org> --- rust/kernel/alloc/kvec.rs | 2 +- rust/kernel/list.rs | 12 ++++++------ 2 files changed, 7 insertions(+), 7 deletions(-) diff --git a/rust/kernel/alloc/kvec.rs b/rust/kernel/alloc/kvec.rs index ae9d072741ce..cde911551327 100644 --- a/rust/kernel/alloc/kvec.rs +++ b/rust/kernel/alloc/kvec.rs @@ -743,7 +743,7 @@ fn into_raw_parts(self) -> (*mut T, NonNull<T>, usize, usize) { pub fn collect(self, flags: Flags) -> Vec<T, A> { let old_layout = self.layout; let (mut ptr, buf, len, mut cap) = self.into_raw_parts(); - let has_advanced = ptr != buf.as_ptr(); + let has_advanced = !core::ptr::eq(ptr, buf.as_ptr()); if has_advanced { // Copy the contents we have advanced to at the beginning of the buffer. diff --git a/rust/kernel/list.rs b/rust/kernel/list.rs index a335c3b1ff5e..c63cbeee3316 100644 --- a/rust/kernel/list.rs +++ b/rust/kernel/list.rs @@ -435,7 +435,7 @@ unsafe fn remove_internal_inner( // * If `item` was the only item in the list, then `prev == item`, and we just set // `item->next` to null, so this correctly sets `first` to null now that the list is // empty. - if self.first == item { + if core::ptr::eq(self.first, item) { // SAFETY: The `prev` pointer is the value that `item->prev` had when it was in this // list, so it must be valid. There is no race since `prev` is still in the list and we // still have exclusive access to the list. @@ -556,7 +556,7 @@ fn next(&mut self) -> Option<ArcBorrow<'a, T>> { let next = unsafe { (*current).next }; // INVARIANT: If `current` was the last element of the list, then this updates it to null. // Otherwise, we update it to the next element. - self.current = if next != self.stop { + self.current = if !core::ptr::eq(next, self.stop) { next } else { ptr::null_mut() @@ -726,7 +726,7 @@ impl<'a, T: ?Sized + ListItem<ID>, const ID: u64> Cursor<'a, T, ID> { fn prev_ptr(&self) -> *mut ListLinksFields { let mut next = self.next; let first = self.list.first; - if next == first { + if core::ptr::eq(next, first) { // We are before the first element. return core::ptr::null_mut(); } @@ -788,7 +788,7 @@ pub fn move_next(&mut self) -> bool { // access the `next` field. let mut next = unsafe { (*self.next).next }; - if next == self.list.first { + if core::ptr::eq(next, self.list.first) { next = core::ptr::null_mut(); } @@ -802,7 +802,7 @@ pub fn move_next(&mut self) -> bool { /// If the cursor is before the first element, then this call does nothing. This call returns /// `true` if the cursor's position was changed. pub fn move_prev(&mut self) -> bool { - if self.next == self.list.first { + if core::ptr::eq(self.next, self.list.first) { return false; } @@ -822,7 +822,7 @@ fn insert_inner(&mut self, item: ListArc<T, ID>) -> *mut ListLinksFields { // * `ptr` is an element in the list or null. // * if `ptr` is null, then `self.list.first` is null so the list is empty. let item = unsafe { self.list.insert_inner(item, ptr) }; - if self.next == self.list.first { + if core::ptr::eq(self.next, self.list.first) { // INVARIANT: We just inserted `item`, so it's a member of list. self.list.first = item; } -- 2.49.0

4 months, 2 weeks

3
2
0 0

[PATCH for 6.1.y] LoongArch: Fix build error due to backport

by Huacai Chen

In 6.1 there is no pmdp_get() definition, so use *pmd directly, in order to avoid such build error due to a recently backport: arch/loongarch/mm/hugetlbpage.c: In function 'huge_pte_offset': arch/loongarch/mm/hugetlbpage.c:50:25: error: implicit declaration of function 'pmdp_get'; did you mean 'ptep_get'? [-Wimplicit-function-declaration] 50 | return pmd_none(pmdp_get(pmd)) ? NULL : (pte_t *) pmd; | ^~~~~~~~ | ptep_get Signed-off-by: Huacai Chen <chenhuacai(a)loongson.cn> --- arch/loongarch/mm/hugetlbpage.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/loongarch/mm/hugetlbpage.c b/arch/loongarch/mm/hugetlbpage.c index cf3b8785a921..70b4a51885c2 100644 --- a/arch/loongarch/mm/hugetlbpage.c +++ b/arch/loongarch/mm/hugetlbpage.c @@ -47,7 +47,7 @@ pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr, pmd = pmd_offset(pud, addr); } } - return pmd_none(pmdp_get(pmd)) ? NULL : (pte_t *) pmd; + return pmd_none(*pmd) ? NULL : (pte_t *) pmd; } /* -- 2.47.1

4 months, 2 weeks

3
2
0 0

[PATCH 6.1] smb: client: fix double free of TCP_Server_Info::hostname

by Pavel Paklov

From: Pavel Paklov <pavel.paklov(a)cyberprotect.ru> From: Paulo Alcantara <pc(a)manguebit.com> commit fa2f9906a7b333ba757a7dbae0713d8a5396186e upstream When shutting down the server in cifs_put_tcp_session(), cifsd thread might be reconnecting to multiple DFS targets before it realizes it should exit the loop, so @server->hostname can't be freed as long as cifsd thread isn't done. Otherwise the following can happen: RIP: 0010:__slab_free+0x223/0x3c0 Code: 5e 41 5f c3 cc cc cc cc 4c 89 de 4c 89 cf 44 89 44 24 08 4c 89 1c 24 e8 fb cf 8e 00 44 8b 44 24 08 4c 8b 1c 24 e9 5f fe ff ff <0f> 0b 41 f7 45 08 00 0d 21 00 0f 85 2d ff ff ff e9 1f ff ff ff 80 RSP: 0018:ffffb26180dbfd08 EFLAGS: 00010246 RAX: ffff8ea34728e510 RBX: ffff8ea34728e500 RCX: 0000000000800068 RDX: 0000000000800068 RSI: 0000000000000000 RDI: ffff8ea340042400 RBP: ffffe112041ca380 R08: 0000000000000001 R09: 0000000000000000 R10: 6170732e31303000 R11: 70726f632e786563 R12: ffff8ea34728e500 R13: ffff8ea340042400 R14: ffff8ea34728e500 R15: 0000000000800068 FS: 0000000000000000(0000) GS:ffff8ea66fd80000(0000) 000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffc25376080 CR3: 000000012a2ba001 CR4: PKRU: 55555554 Call Trace: <TASK> ? show_trace_log_lvl+0x1c4/0x2df ? show_trace_log_lvl+0x1c4/0x2df ? __reconnect_target_unlocked+0x3e/0x160 [cifs] ? __die_body.cold+0x8/0xd ? die+0x2b/0x50 ? do_trap+0xce/0x120 ? __slab_free+0x223/0x3c0 ? do_error_trap+0x65/0x80 ? __slab_free+0x223/0x3c0 ? exc_invalid_op+0x4e/0x70 ? __slab_free+0x223/0x3c0 ? asm_exc_invalid_op+0x16/0x20 ? __slab_free+0x223/0x3c0 ? extract_hostname+0x5c/0xa0 [cifs] ? extract_hostname+0x5c/0xa0 [cifs] ? __kmalloc+0x4b/0x140 __reconnect_target_unlocked+0x3e/0x160 [cifs] reconnect_dfs_server+0x145/0x430 [cifs] cifs_handle_standard+0x1ad/0x1d0 [cifs] cifs_demultiplex_thread+0x592/0x730 [cifs] ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs] kthread+0xdd/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x29/0x50 </TASK> Fixes: 7be3248f3139 ("cifs: To match file servers, make sure the server hostname matches") Reported-by: Jay Shin <jaeshin(a)redhat.com> Signed-off-by: Paulo Alcantara (Red Hat) <pc(a)manguebit.com> Signed-off-by: Steve French <stfrench(a)microsoft.com> Signed-off-by: Pavel Paklov <pavel.paklov(a)cyberprotect.ru> --- Backport fix for CVE-2025-21673 fs/smb/client/connect.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/fs/smb/client/connect.c b/fs/smb/client/connect.c index 01ce81f77e89..2b0657fe2a3f 100644 --- a/fs/smb/client/connect.c +++ b/fs/smb/client/connect.c @@ -1066,6 +1066,7 @@ static void clean_demultiplex_info(struct TCP_Server_Info *server) kfree(server->origin_fullpath); kfree(server->leaf_fullpath); #endif + kfree(server->hostname); kfree(server); length = atomic_dec_return(&tcpSesAllocCount); @@ -1688,8 +1689,6 @@ cifs_put_tcp_session(struct TCP_Server_Info *server, int from_reconnect) kfree_sensitive(server->session_key.response); server->session_key.response = NULL; server->session_key.len = 0; - kfree(server->hostname); - server->hostname = NULL; task = xchg(&server->tsk, NULL); if (task) -- 2.43.0

4 months, 2 weeks

2
1
0 0

[PATCH 6.12.y] bpf: Fix BPF_INTERNAL namespace import

by Xi Ruoyao

The commit cdd30ebb1b9f ("module: Convert symbol namespace to string literal") makes the grammar of MODULE_IMPORT_NS and EXPORT_SYMBOL_NS different between the stable branches and the mainline. But when the commit 955f9ede52b8 ("bpf: Add namespace to BPF internal symbols") was backported from mainline, only EXPORT_SYMBOL_NS instances are adapted, leaving the MODULE_IMPORT_NS instance with the "new" grammar and causing the module fails to build: ERROR: modpost: module bpf_preload uses symbol bpf_link_get_from_fd from namespace BPF_INTERNAL, but does not import it. ERROR: modpost: module bpf_preload uses symbol kern_sys_bpf from namespace BPF_INTERNAL, but does not import it. Reported-by: Mingcong Bai <jeffbai(a)aosc.io> Reported-by: Alex Davis <alex47794(a)gmail.com> Closes: https://lore.kernel.org/all/CADiockBKBQTVqjA5G+RJ9LBwnEnZ8o0odYnL=LBZ_7QN=_… Fixes: 955f9ede52b8 ("bpf: Add namespace to BPF internal symbols") Signed-off-by: Xi Ruoyao <xry111(a)xry111.site> --- kernel/bpf/preload/bpf_preload_kern.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/bpf/preload/bpf_preload_kern.c b/kernel/bpf/preload/bpf_preload_kern.c index 56a81df7a9d7..fdad0eb308fe 100644 --- a/kernel/bpf/preload/bpf_preload_kern.c +++ b/kernel/bpf/preload/bpf_preload_kern.c @@ -89,5 +89,5 @@ static void __exit fini(void) } late_initcall(load); module_exit(fini); -MODULE_IMPORT_NS("BPF_INTERNAL"); +MODULE_IMPORT_NS(BPF_INTERNAL); MODULE_LICENSE("GPL"); -- 2.49.0

4 months, 2 weeks

3
2
0 0

Please apply to v6.14.x commit 6eab70345799 ("ASoC: soc-core: Stop using of_property_read_bool() for non-boolean properties")

by LEROY Christophe

Hi, Could you please apply commit 6eab70345799 ("ASoC: soc-core: Stop using of_property_read_bool() for non-boolean properties") to v6.14.x in order to silence warnings introduced in v6.14 by commit c141ecc3cecd ("of: Warn when of_property_read_bool() is used on non-boolean properties") Thanks Christophe

4 months, 2 weeks

3
4
0 0

[GIT PULL] bcachefs fixes for 6.14.y

by Kent Overstreet

The following changes since commit 02a22be3c0003af08df510cba3d79d00c6495b74: bcachefs: bch2_ioctl_subvolume_destroy() fixes (2025-04-03 16:13:53 -0400) are available in the Git repository at: git://evilpiepirate.org/bcachefs.git tags/bcachefs-for-6.14-2025-05-02 for you to fetch changes up to 52b17bca7b20663e5df6dbfc24cc2030259b64b6: bcachefs: Remove incorrect __counted_by annotation (2025-05-02 21:09:51 -0400) ---------------------------------------------------------------- bcachefs fixes for 6.15 remove incorrect counted_by annotation, fixing FORTIFY_SOURCE crashes that have been hitting arch users ---------------------------------------------------------------- Alan Huang (1): bcachefs: Remove incorrect __counted_by annotation fs/bcachefs/xattr_format.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)

4 months, 2 weeks

2
6
0 0

[6.12.y] WARNING: CPU: 0 PID: 681 at block/blk-mq-cpumap.c:90 blk_mq_map_hw_queues+0xcf/0xe0

by Wang Yugui

Hi, I noticed a WARNING in recent 6.12.y kernel. This WARNING happen on 6.12.26/6.12.25, but not happen on 6.12.20. More bisect job need to be done, but reporti it firstly. [ 13.288365] ------------[ cut here ]------------ [ 13.288366] WARNING: CPU: 0 PID: 681 at block/blk-mq-cpumap.c:90 blk_mq_map_hw_queues+0xcf/0xe0 void blk_mq_map_hw_queues(struct blk_mq_queue_map *qmap, struct device *dev, unsigned int offset) { ... ... fallback: L90： WARN_ON_ONCE(qmap->nr_queues > 1); blk_mq_clear_mq_map(qmap); } [ 13.288373] Modules linked in: ahci(+) mlxfw libahci pci_hyperv_intf bnx2x(+) i40e(+) mpi3mr(+) psample bnxt_en(+) libata mgag200(+) tls megaraid_sas(+) crc32c_intel scsi_transport_sas mdio libie i2c_algo_bit wmi dm_mirror dm_region_hash dm_log dm_mod [ 13.288386] CPU: 0 UID: 0 PID: 681 Comm: kworker/0:2 Not tainted 6.12.26-1.el7.x86_64 #1 [ 13.288388] Hardware name: Dell Inc. PowerEdge T640/0TWW5Y, BIOS 2.22.1 09/12/2024 [ 13.288390] Workqueue: events work_for_cpu_fn [ 13.288394] RIP: 0010:blk_mq_map_hw_queues+0xcf/0xe0 [ 13.288396] Code: 8b 35 85 e4 9a 02 48 63 d0 48 c7 c7 e0 e5 78 94 e8 26 0b 07 00 39 05 70 e4 9a 02 77 d3 5b 5d 41 5c 41 5d 41 5e c3 cc cc cc cc <0f> 0b eb d2 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 90 90 90 90 90 [ 13.288398] RSP: 0018:ffffc0e11b83bd38 EFLAGS: 00010212 [ 13.288400] RAX: 0000000000000000 RBX: ffffa0804ad58000 RCX: 0000000000000050 [ 13.288402] RDX: 0000000000000050 RSI: ffffa07f8f24d0c8 RDI: ffffa0804ad580e8 [ 13.288403] RBP: ffffa0804ad580e0 R08: 000000000000004f R09: 0000000000000000 [ 13.288404] R10: ffffc0e11b83bd78 R11: ffffa07f9039da00 R12: 0000000000000000 [ 13.288405] R13: 0000000000000001 R14: ffffa0804ad580e8 R15: 0000000000000000 [ 13.288406] FS: 0000000000000000(0000) GS:ffffa0dd3fe00000(0000) knlGS:0000000000000000 [ 13.288407] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 13.288408] CR2: 00007f1f3226ba20 CR3: 00000002f9780005 CR4: 00000000007706f0 [ 13.288409] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 13.288410] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 13.288411] PKRU: 55555554 [ 13.288412] Call Trace: [ 13.288413] <TASK> [ 13.288415] megasas_map_queues+0x49/0x90 [megaraid_sas] [ 13.288431] blk_mq_alloc_tag_set+0x150/0x3b0 [ 13.288436] scsi_add_host_with_dma+0xd0/0x350 [ 13.288440] megasas_io_attach+0x15c/0x220 [megaraid_sas] [ 13.288456] megasas_probe_one+0x1cb/0x570 [megaraid_sas] [ 13.288468] local_pci_probe+0x47/0xa0 [ 13.288474] work_for_cpu_fn+0x17/0x30 [ 13.288475] process_one_work+0x179/0x3a0 [ 13.288480] worker_thread+0x24b/0x350 [ 13.288483] ? __pfx_worker_thread+0x10/0x10 [ 13.288485] kthread+0xde/0x110 [ 13.288489] ? __pfx_kthread+0x10/0x10 [ 13.288491] ret_from_fork+0x31/0x50 [ 13.288494] ? __pfx_kthread+0x10/0x10 [ 13.288496] ret_from_fork_asm+0x1a/0x30 [ 13.288502] </TASK> [ 13.288502] ---[ end trace 0000000000000000 ]--- Best Regards Wang Yugui (wangyugui(a)e16-tech.com) 2025/05/03

4 months, 2 weeks

6
9
0 0

[GIT PULL] bcachefs fixes for 6.12.y

by Kent Overstreet

The following changes since commit 1a7a2300e0dd8b4a73bcd3777a2947fe42a16bef: bcachefs: bch2_ioctl_subvolume_destroy() fixes (2025-03-31 13:16:15 -0400) are available in the Git repository at: git://evilpiepirate.org/bcachefs.git tags/bcachefs-for-6.12-2025-05-5 for you to fetch changes up to 3f105630c0b2e53a93713c2328e3426081f961c1: bcachefs: Remove incorrect __counted_by annotation (2025-05-05 09:41:26 -0400) ---------------------------------------------------------------- bcachefs fixes for 6.12 remove incorrect counted_by annotation, fixing FORTIFY_SOURCE crashes that have been hitting arch users ---------------------------------------------------------------- Alan Huang (1): bcachefs: Remove incorrect __counted_by annotation fs/bcachefs/xattr_format.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)

4 months, 2 weeks

1
0
0 0

[tip: timers/urgent] clocksource/i8253: Use raw_spinlock_irqsave() in clockevent_i8253_disable()

by tip-bot2 for Sebastian Andrzej Siewior

The following commit has been merged into the timers/urgent branch of tip: Commit-ID: 94cff94634e506a4a44684bee1875d2dbf782722 Gitweb: https://git.kernel.org/tip/94cff94634e506a4a44684bee1875d2dbf782722 Author: Sebastian Andrzej Siewior <bigeasy(a)linutronix.de> AuthorDate: Fri, 04 Apr 2025 15:31:16 +02:00 Committer: Thomas Gleixner <tglx(a)linutronix.de> CommitterDate: Mon, 05 May 2025 15:34:49 +02:00 clocksource/i8253: Use raw_spinlock_irqsave() in clockevent_i8253_disable() On x86 during boot, clockevent_i8253_disable() can be invoked via x86_late_time_init -> hpet_time_init() -> pit_timer_init() which happens with enabled interrupts. If some of the old i8253 hardware is actually used then lockdep will notice that i8253_lock is used in hard interrupt context. This causes lockdep to complain because it observed the lock being acquired with interrupts enabled and in hard interrupt context. Make clockevent_i8253_disable() acquire the lock with raw_spinlock_irqsave() to cure this. [ tglx: Massage change log and use guard() ] Fixes: c8c4076723dac ("x86/timer: Skip PIT initialization on modern chipsets") Signed-off-by: Sebastian Andrzej Siewior <bigeasy(a)linutronix.de> Signed-off-by: Thomas Gleixner <tglx(a)linutronix.de> Cc: stable(a)vger.kernel.org Link: https://lore.kernel.org/all/20250404133116.p-XRWJXf@linutronix.de --- drivers/clocksource/i8253.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/clocksource/i8253.c b/drivers/clocksource/i8253.c index 39f7c2d..b603c25 100644 --- a/drivers/clocksource/i8253.c +++ b/drivers/clocksource/i8253.c @@ -103,7 +103,7 @@ int __init clocksource_i8253_init(void) #ifdef CONFIG_CLKEVT_I8253 void clockevent_i8253_disable(void) { - raw_spin_lock(&i8253_lock); + guard(raw_spinlock_irqsave)(&i8253_lock); /* * Writing the MODE register should stop the counter, according to @@ -132,8 +132,6 @@ void clockevent_i8253_disable(void) outb_p(0, PIT_CH0); outb_p(0x30, PIT_MODE); - - raw_spin_unlock(&i8253_lock); } static int pit_shutdown(struct clock_event_device *evt)

4 months, 2 weeks

1
0
0 0

FAILED: patch "[PATCH] ASoC: soc-core: Stop using of_property_read_bool() for" failed to apply to 6.6-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 6.6-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. To reproduce the conflict and resubmit, you may use the following commands: git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.6.y git checkout FETCH_HEAD git cherry-pick -x 6eab70345799 # <resolve conflicts, build, test, etc.> git commit -s git send-email --to '<stable(a)vger.kernel.org>' --in-reply-to '2025050546-commute-subduing-1917@gregkh' --subject-prefix 'PATCH 6.6.y' HEAD^.. Possible dependencies: thanks, greg k-h ------------------ original commit in Linus's tree ------------------ From 6eab7034579917f207ca6d8e3f4e11e85e0ab7d5 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven <geert+renesas(a)glider.be> Date: Wed, 22 Jan 2025 09:21:27 +0100 Subject: [PATCH] ASoC: soc-core: Stop using of_property_read_bool() for non-boolean properties On R-Car: OF: /sound: Read of boolean property 'simple-audio-card,bitclock-master' with a value. OF: /sound: Read of boolean property 'simple-audio-card,frame-master' with a value. or: OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'bitclock-master' with a value. OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. The use of of_property_read_bool() for non-boolean properties is deprecated in favor of of_property_present() when testing for property presence. Replace testing for presence before calling of_property_read_u32() by testing for an -EINVAL return value from the latter, to simplify the code. Signed-off-by: Geert Uytterhoeven <geert+renesas(a)glider.be> Link: https://patch.msgid.link/db10e96fbda121e7456d70e97a013cbfc9755f4d.173753395… Signed-off-by: Mark Brown <broonie(a)kernel.org> diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c index 3c6d8aef4130..26b34b688508 100644 --- a/sound/soc/soc-core.c +++ b/sound/soc/soc-core.c @@ -3046,7 +3046,7 @@ int snd_soc_of_parse_pin_switches(struct snd_soc_card *card, const char *prop) unsigned int i, nb_controls; int ret; - if (!of_property_read_bool(dev->of_node, prop)) + if (!of_property_present(dev->of_node, prop)) return 0; strings = devm_kcalloc(dev, nb_controls_max, @@ -3120,23 +3120,17 @@ int snd_soc_of_parse_tdm_slot(struct device_node *np, if (rx_mask) snd_soc_of_get_slot_mask(np, "dai-tdm-slot-rx-mask", rx_mask); - if (of_property_read_bool(np, "dai-tdm-slot-num")) { - ret = of_property_read_u32(np, "dai-tdm-slot-num", &val); - if (ret) - return ret; + ret = of_property_read_u32(np, "dai-tdm-slot-num", &val); + if (ret && ret != -EINVAL) + return ret; + if (!ret && slots) + *slots = val; - if (slots) - *slots = val; - } - - if (of_property_read_bool(np, "dai-tdm-slot-width")) { - ret = of_property_read_u32(np, "dai-tdm-slot-width", &val); - if (ret) - return ret; - - if (slot_width) - *slot_width = val; - } + ret = of_property_read_u32(np, "dai-tdm-slot-width", &val); + if (ret && ret != -EINVAL) + return ret; + if (!ret && slot_width) + *slot_width = val; return 0; } @@ -3403,12 +3397,12 @@ unsigned int snd_soc_daifmt_parse_clock_provider_raw(struct device_node *np, * check "[prefix]frame-master" */ snprintf(prop, sizeof(prop), "%sbitclock-master", prefix); - bit = of_property_read_bool(np, prop); + bit = of_property_present(np, prop); if (bit && bitclkmaster) *bitclkmaster = of_parse_phandle(np, prop, 0); snprintf(prop, sizeof(prop), "%sframe-master", prefix); - frame = of_property_read_bool(np, prop); + frame = of_property_present(np, prop); if (frame && framemaster) *framemaster = of_parse_phandle(np, prop, 0);

4 months, 2 weeks

1
0
0 0

[PATCH 2/2] xhci: dbc: Avoid event polling busyloop if pending rx transfers are inactive.

by Mathias Nyman

Event polling delay is set to 0 if there are any pending requests in either rx or tx requests lists. Checking for pending requests does not work well for "IN" transfers as the tty driver always queues requests to the list and TRBs to the ring, preparing to receive data from the host. This causes unnecessary busylooping and cpu hogging. Only set the event polling delay to 0 if there are pending tx "write" transfers, or if it was less than 10ms since last active data transfer in any direction. Cc: Łukasz Bartosik <ukaszb(a)chromium.org> Fixes: fb18e5bb9660 ("xhci: dbc: poll at different rate depending on data transfer activity") Cc: stable(a)vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com> --- drivers/usb/host/xhci-dbgcap.c | 19 ++++++++++++++++--- drivers/usb/host/xhci-dbgcap.h | 3 +++ 2 files changed, 19 insertions(+), 3 deletions(-) diff --git a/drivers/usb/host/xhci-dbgcap.c b/drivers/usb/host/xhci-dbgcap.c index fd7895b24367..0d4ce5734165 100644 --- a/drivers/usb/host/xhci-dbgcap.c +++ b/drivers/usb/host/xhci-dbgcap.c @@ -823,6 +823,7 @@ static enum evtreturn xhci_dbc_do_handle_events(struct xhci_dbc *dbc) { dma_addr_t deq; union xhci_trb *evt; + enum evtreturn ret = EVT_DONE; u32 ctrl, portsc; bool update_erdp = false; @@ -909,6 +910,7 @@ static enum evtreturn xhci_dbc_do_handle_events(struct xhci_dbc *dbc) break; case TRB_TYPE(TRB_TRANSFER): dbc_handle_xfer_event(dbc, evt); + ret = EVT_XFER_DONE; break; default: break; @@ -927,7 +929,7 @@ static enum evtreturn xhci_dbc_do_handle_events(struct xhci_dbc *dbc) lo_hi_writeq(deq, &dbc->regs->erdp); } - return EVT_DONE; + return ret; } static void xhci_dbc_handle_events(struct work_struct *work) @@ -936,6 +938,7 @@ static void xhci_dbc_handle_events(struct work_struct *work) struct xhci_dbc *dbc; unsigned long flags; unsigned int poll_interval; + unsigned long busypoll_timelimit; dbc = container_of(to_delayed_work(work), struct xhci_dbc, event_work); poll_interval = dbc->poll_interval; @@ -954,11 +957,21 @@ static void xhci_dbc_handle_events(struct work_struct *work) dbc->driver->disconnect(dbc); break; case EVT_DONE: - /* set fast poll rate if there are pending data transfers */ + /* + * Set fast poll rate if there are pending out transfers, or + * a transfer was recently processed + */ + busypoll_timelimit = dbc->xfer_timestamp + + msecs_to_jiffies(DBC_XFER_INACTIVITY_TIMEOUT); + if (!list_empty(&dbc->eps[BULK_OUT].list_pending) || - !list_empty(&dbc->eps[BULK_IN].list_pending)) + time_is_after_jiffies(busypoll_timelimit)) poll_interval = 0; break; + case EVT_XFER_DONE: + dbc->xfer_timestamp = jiffies; + poll_interval = 0; + break; default: dev_info(dbc->dev, "stop handling dbc events\n"); return; diff --git a/drivers/usb/host/xhci-dbgcap.h b/drivers/usb/host/xhci-dbgcap.h index 9dc8f4d8077c..47ac72c2286d 100644 --- a/drivers/usb/host/xhci-dbgcap.h +++ b/drivers/usb/host/xhci-dbgcap.h @@ -96,6 +96,7 @@ struct dbc_ep { #define DBC_WRITE_BUF_SIZE 8192 #define DBC_POLL_INTERVAL_DEFAULT 64 /* milliseconds */ #define DBC_POLL_INTERVAL_MAX 5000 /* milliseconds */ +#define DBC_XFER_INACTIVITY_TIMEOUT 10 /* milliseconds */ /* * Private structure for DbC hardware state: */ @@ -142,6 +143,7 @@ struct xhci_dbc { enum dbc_state state; struct delayed_work event_work; unsigned int poll_interval; /* ms */ + unsigned long xfer_timestamp; unsigned resume_required:1; struct dbc_ep eps[2]; @@ -187,6 +189,7 @@ struct dbc_request { enum evtreturn { EVT_ERR = -1, EVT_DONE, + EVT_XFER_DONE, EVT_GSER, EVT_DISC, }; -- 2.43.0

4 months, 2 weeks

1
0
0 0

[PATCH] arm64: dts: amlogic: dreambox: fix missing clkc_audio node

by Christian Hewitt

Add the clkc_audio node to fix audio support on Dreambox One/Two. Fixes: 83a6f4c62cb1 ("arm64: dts: meson: add initial support for Dreambox One/Two") CC: <stable(a)vger.kernel.org> Suggested-by: Emanuel Strobel <emanuel.strobel(a)yahoo.com> Signed-off-by: Christian Hewitt <christianshewitt(a)gmail.com> --- arch/arm64/boot/dts/amlogic/meson-g12b-dreambox.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-dreambox.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-dreambox.dtsi index de35fa2d7a6d..8e3e3354ed67 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-dreambox.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-dreambox.dtsi @@ -116,6 +116,10 @@ &arb { status = "okay"; }; +&clkc_audio { + status = "okay"; +}; + &frddr_a { status = "okay"; }; -- 2.34.1

4 months, 2 weeks

3
2
0 0

[PATCH 6.14.y] btrfs: fix the inode leak in btrfs_iget()

by Penglei Jiang

[BUG] There is a bug report that a syzbot reproducer can lead to the following busy inode at unmount time: BTRFS info (device loop1): last unmount of filesystem 1680000e-3c1e-4c46-84b6-56bd3909af50 VFS: Busy inodes after unmount of loop1 (btrfs) ------------[ cut here ]------------ kernel BUG at fs/super.c:650! Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI CPU: 0 UID: 0 PID: 48168 Comm: syz-executor Not tainted 6.15.0-rc2-00471-g119009db2674 #2 PREEMPT(full) Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:generic_shutdown_super+0x2e9/0x390 fs/super.c:650 Call Trace: <TASK> kill_anon_super+0x3a/0x60 fs/super.c:1237 btrfs_kill_super+0x3b/0x50 fs/btrfs/super.c:2099 deactivate_locked_super+0xbe/0x1a0 fs/super.c:473 deactivate_super fs/super.c:506 [inline] deactivate_super+0xe2/0x100 fs/super.c:502 cleanup_mnt+0x21f/0x440 fs/namespace.c:1435 task_work_run+0x14d/0x240 kernel/task_work.c:227 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x269/0x290 kernel/entry/common.c:218 do_syscall_64+0xd4/0x250 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> [CAUSE] When btrfs_alloc_path() failed, btrfs_iget() directly returned without releasing the inode already allocated by btrfs_iget_locked(). This results the above busy inode and trigger the kernel BUG. [FIX] Fix it by calling iget_failed() if btrfs_alloc_path() failed. If we hit error inside btrfs_read_locked_inode(), it will properly call iget_failed(), so nothing to worry about. Although the iget_failed() cleanup inside btrfs_read_locked_inode() is a break of the normal error handling scheme, let's fix the obvious bug and backport first, then rework the error handling later. Reported-by: Penglei Jiang <superman.xpt(a)gmail.com> Link: https://lore.kernel.org/linux-btrfs/20250421102425.44431-1-superman.xpt@gma… Fixes: 7c855e16ab72 ("btrfs: remove conditional path allocation in btrfs_read_locked_inode()") CC: stable(a)vger.kernel.org # 6.13+ Reviewed-by: Qu Wenruo <wqu(a)suse.com> Signed-off-by: Penglei Jiang <superman.xpt(a)gmail.com> Signed-off-by: David Sterba <dsterba(a)suse.com> (cherry picked from commit 48c1d1bb525b1c44b8bdc8e7ec5629cb6c2b9fc4) --- fs/btrfs/inode.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index 38756f8cef46..ad7009d336fa 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -5659,8 +5659,10 @@ struct inode *btrfs_iget(u64 ino, struct btrfs_root *root) return inode; path = btrfs_alloc_path(); - if (!path) + if (!path) { + iget_failed(&inode->vfs_inode); return ERR_PTR(-ENOMEM); + } ret = btrfs_read_locked_inode(inode, path); btrfs_free_path(path); -- 2.17.1

4 months, 2 weeks

1
0
0 0

[PATCH v2 rc] iommu: Skip PASID validation for devices without PASID capability

by Tushar Dave

Generally PASID support requires ACS settings that usually create single device groups, but there are some niche cases where we can get multi-device groups and still have working PASID support. The primary issue is that PCI switches are not required to treat PASID tagged TLPs specially so appropriate ACS settings are required to route all TLPs to the host bridge if PASID is going to work properly. pci_enable_pasid() does check that each device that will use PASID has the proper ACS settings to achieve this routing. However, no-PASID devices can be combined with PASID capable devices within the same topology using non-uniform ACS settings. In this case the no-PASID devices may not have strict route to host ACS flags and end up being grouped with the PASID devices. This configuration fails to allow use of the PASID within the iommu core code which wrongly checks if the no-PASID device supports PASID. Fix this by ignoring no-PASID devices during the PASID validation. They will never issue a PASID TLP anyhow so they can be ignored. Fixes: c404f55c26fc ("iommu: Validate the PASID in iommu_attach_device_pasid()") Cc: stable(a)vger.kernel.org Signed-off-by: Tushar Dave <tdave(a)nvidia.com> --- changes in v2: - added no-pasid check in __iommu_set_group_pasid and __iommu_remove_group_pasid drivers/iommu/iommu.c | 22 ++++++++++++++++------ 1 file changed, 16 insertions(+), 6 deletions(-) diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c index 60aed01e54f2..8251b07f4022 100644 --- a/drivers/iommu/iommu.c +++ b/drivers/iommu/iommu.c @@ -3329,8 +3329,9 @@ static int __iommu_set_group_pasid(struct iommu_domain *domain, int ret; for_each_group_device(group, device) { - ret = domain->ops->set_dev_pasid(domain, device->dev, - pasid, NULL); + if (device->dev->iommu->max_pasids > 0) + ret = domain->ops->set_dev_pasid(domain, device->dev, + pasid, NULL); if (ret) goto err_revert; } @@ -3342,7 +3343,8 @@ static int __iommu_set_group_pasid(struct iommu_domain *domain, for_each_group_device(group, device) { if (device == last_gdev) break; - iommu_remove_dev_pasid(device->dev, pasid, domain); + if (device->dev->iommu->max_pasids > 0) + iommu_remove_dev_pasid(device->dev, pasid, domain); } return ret; } @@ -3353,8 +3355,10 @@ static void __iommu_remove_group_pasid(struct iommu_group *group, { struct group_device *device; - for_each_group_device(group, device) - iommu_remove_dev_pasid(device->dev, pasid, domain); + for_each_group_device(group, device) { + if (device->dev->iommu->max_pasids > 0) + iommu_remove_dev_pasid(device->dev, pasid, domain); + } } /* @@ -3391,7 +3395,13 @@ int iommu_attach_device_pasid(struct iommu_domain *domain, mutex_lock(&group->mutex); for_each_group_device(group, device) { - if (pasid >= device->dev->iommu->max_pasids) { + /* + * Skip PASID validation for devices without PASID support + * (max_pasids = 0). These devices cannot issue transactions + * with PASID, so they don't affect group's PASID usage. + */ + if ((device->dev->iommu->max_pasids > 0) && + (pasid >= device->dev->iommu->max_pasids)) { ret = -EINVAL; goto out_unlock; } -- 2.34.1

4 months, 2 weeks

3
4
0 0

[PATCH] xfs: fix diff_two_keys calculation for cnt btree

by Fedor Pchelkin

Currently the difference is computed on 32-bit unsigned values although eventually it is stored in a variable of int64_t type. This gives awkward results, e.g. when the diff _should_ be negative, it is represented as some large positive int64_t value. Perform the calculations directly in int64_t as all other diff_two_keys routines actually do. Found by Linux Verification Center (linuxtesting.org) with Svace static analysis tool. Fixes: 08438b1e386b ("xfs: plumb in needed functions for range querying of the freespace btrees") Cc: stable(a)vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin(a)ispras.ru> --- fs/xfs/libxfs/xfs_alloc_btree.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/fs/xfs/libxfs/xfs_alloc_btree.c b/fs/xfs/libxfs/xfs_alloc_btree.c index a4ac37ba5d51..b3c54ae90e25 100644 --- a/fs/xfs/libxfs/xfs_alloc_btree.c +++ b/fs/xfs/libxfs/xfs_alloc_btree.c @@ -238,13 +238,13 @@ xfs_cntbt_diff_two_keys( ASSERT(!mask || (mask->alloc.ar_blockcount && mask->alloc.ar_startblock)); - diff = be32_to_cpu(k1->alloc.ar_blockcount) - - be32_to_cpu(k2->alloc.ar_blockcount); + diff = (int64_t)be32_to_cpu(k1->alloc.ar_blockcount) - + be32_to_cpu(k2->alloc.ar_blockcount); if (diff) return diff; - return be32_to_cpu(k1->alloc.ar_startblock) - - be32_to_cpu(k2->alloc.ar_startblock); + return (int64_t)be32_to_cpu(k1->alloc.ar_startblock) - + be32_to_cpu(k2->alloc.ar_startblock); } static xfs_failaddr_t -- 2.49.0

4 months, 2 weeks

3
4
0 0

[PATCH] arm64: dts: qcom: ipq5424: fix MSI base vector interrupt number

by Kathiravan Thirumoorthy

From: Vignesh Viswanathan <quic_viswanat(a)quicinc.com> As per the hardware design, MSI interrupt starts from 704. Fix the same. Cc: stable(a)vger.kernel.org Fixes: 1a91d2a6021e ("arm64: dts: qcom: add IPQ5424 SoC and rdp466 board support") Signed-off-by: Vignesh Viswanathan <quic_viswanat(a)quicinc.com> Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy(a)oss.qualcomm.com> --- arch/arm64/boot/dts/qcom/ipq5424.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/ipq5424.dtsi b/arch/arm64/boot/dts/qcom/ipq5424.dtsi index 5d6ed2172b1bb0a57c593f121f387ec917f42419..7a2e5c89b26ad8010f158be6f052b307e8a32fb5 100644 --- a/arch/arm64/boot/dts/qcom/ipq5424.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq5424.dtsi @@ -371,7 +371,7 @@ intc: interrupt-controller@f200000 { #redistributor-regions = <1>; redistributor-stride = <0x0 0x20000>; interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; - mbi-ranges = <672 128>; + mbi-ranges = <704 128>; msi-controller; }; --- base-commit: 407f60a151df3c44397e5afc0111eb9b026c38d3 change-id: 20250505-msi-vector-f0dcd22233d9 Best regards, -- Kathiravan Thirumoorthy <kathiravan.thirumoorthy(a)oss.qualcomm.com>

4 months, 2 weeks

1
1
0 0

[PATCH 0/7] accel/ivpu: Add context violation handling for 6.12

by Jacek Lawrynowicz

These patchset adds support for VPU_JSM_STATUS_MVNCI_CONTEXT_VIOLATION_HW message added in recent VPU firmware. Without it the driver will not be able to process any jobs after this message is received and would need to be reloaded. Most patches are as-is from upstream besides these two: - Fix locking order in ivpu_job_submit - Abort all jobs after command queue unregister Both these patches need to be rebased because of missing new CMDQ UAPI changes that should not be backported to stable. Andrew Kreimer (1): accel/ivpu: Fix a typo Andrzej Kacprowski (1): accel/ivpu: Update VPU FW API headers Karol Wachowski (4): accel/ivpu: Use xa_alloc_cyclic() instead of custom function accel/ivpu: Abort all jobs after command queue unregister accel/ivpu: Fix locking order in ivpu_job_submit accel/ivpu: Add handling of VPU_JSM_STATUS_MVNCI_CONTEXT_VIOLATION_HW Tomasz Rusinowicz (1): accel/ivpu: Make DB_ID and JOB_ID allocations incremental drivers/accel/ivpu/ivpu_drv.c | 38 ++-- drivers/accel/ivpu/ivpu_drv.h | 9 + drivers/accel/ivpu/ivpu_job.c | 125 +++++++++--- drivers/accel/ivpu/ivpu_job.h | 1 + drivers/accel/ivpu/ivpu_jsm_msg.c | 3 +- drivers/accel/ivpu/ivpu_mmu.c | 3 +- drivers/accel/ivpu/ivpu_sysfs.c | 5 +- drivers/accel/ivpu/vpu_boot_api.h | 45 +++-- drivers/accel/ivpu/vpu_jsm_api.h | 303 +++++++++++++++++++++++++----- 9 files changed, 412 insertions(+), 120 deletions(-) -- 2.45.1

4 months, 2 weeks

3
16
0 0

[PATCH v2 0/3] accel/ivpu: Add context violation handling for 6.14

by Jacek Lawrynowicz

These patchset adds support for VPU_JSM_STATUS_MVNCI_CONTEXT_VIOLATION_HW message added in recent VPU firmware. Without it the driver will not be able to process any jobs after this message is received and would need to be reloaded. The last patch in this series is as-is from upstream, but other two patches had to be rebased because of missing new CMDQ UAPI changes that should not be backported to stable. Changes since v1: - Documented deviations from the original upstream patches in commit messages Karol Wachowski (3): accel/ivpu: Abort all jobs after command queue unregister accel/ivpu: Fix locking order in ivpu_job_submit accel/ivpu: Add handling of VPU_JSM_STATUS_MVNCI_CONTEXT_VIOLATION_HW drivers/accel/ivpu/ivpu_drv.c | 32 ++------- drivers/accel/ivpu/ivpu_drv.h | 2 + drivers/accel/ivpu/ivpu_job.c | 111 ++++++++++++++++++++++++++------ drivers/accel/ivpu/ivpu_job.h | 1 + drivers/accel/ivpu/ivpu_mmu.c | 3 +- drivers/accel/ivpu/ivpu_sysfs.c | 5 +- 6 files changed, 103 insertions(+), 51 deletions(-) -- 2.45.1

4 months, 2 weeks

1
3
0 0

[PATCH] fs: minix: Fix handling of corrupted directories

by Andrey Kriulin

If the directory is corrupted and the number of nlinks is less than 2 (valid nlinks have at least 2), then when the directory is deleted, the minix_rmdir will try to reduce the nlinks(unsigned int) to a negative value. Make nlinks validity check for directory in minix_lookup. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable(a)vger.kernel.org Signed-off-by: Andrey Kriulin <kitotavrik.media(a)gmail.com> --- fs/minix/namei.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/fs/minix/namei.c b/fs/minix/namei.c index 8938536d8..5717a56fa 100644 --- a/fs/minix/namei.c +++ b/fs/minix/namei.c @@ -28,8 +28,13 @@ static struct dentry *minix_lookup(struct inode * dir, struct dentry *dentry, un return ERR_PTR(-ENAMETOOLONG); ino = minix_inode_by_name(dentry); - if (ino) + if (ino) { inode = minix_iget(dir->i_sb, ino); + if (S_ISDIR(inode->i_mode) && inode->i_nlink < 2) { + iput(inode); + return ERR_PTR(-EIO); + } + } return d_splice_alias(inode, dentry); } -- 2.47.2

4 months, 2 weeks

4
3
0 0

[PATCH] fs: minix: Fix handling of corrupted directories

by Andrey Kriulin

If the directory is corrupted and the number of nlinks is less than 2 (valid nlinks have at least 2), then when the directory is deleted, the minix_rmdir will try to reduce the nlinks(unsigned int) to a negative value. Make nlinks validity check for directory in minix_lookup. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable(a)vger.kernel.org Signed-off-by: Andrey Kriulin <kitotavrik.media(a)gmail.com> --- fs/minix/namei.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/fs/minix/namei.c b/fs/minix/namei.c index 8938536d8..5717a56fa 100644 --- a/fs/minix/namei.c +++ b/fs/minix/namei.c @@ -28,8 +28,13 @@ static struct dentry *minix_lookup(struct inode * dir, struct dentry *dentry, un return ERR_PTR(-ENAMETOOLONG); ino = minix_inode_by_name(dentry); - if (ino) + if (ino) { inode = minix_iget(dir->i_sb, ino); + if (S_ISDIR(inode->i_mode) && inode->i_nlink < 2) { + iput(inode); + return ERR_PTR(-EIO); + } + } return d_splice_alias(inode, dentry); } -- 2.47.2

4 months, 2 weeks

2
1
0 0

FAILED: patch "[PATCH] dm-bufio: don't schedule in atomic context" failed to apply to 6.1-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 6.1-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. To reproduce the conflict and resubmit, you may use the following commands: git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.1.y git checkout FETCH_HEAD git cherry-pick -x a3d8f0a7f5e8b193db509c7191fefeed3533fc44 # <resolve conflicts, build, test, etc.> git commit -s git send-email --to '<stable(a)vger.kernel.org>' --in-reply-to '2025050552-backslid-thirsting-324d@gregkh' --subject-prefix 'PATCH 6.1.y' HEAD^.. Possible dependencies: thanks, greg k-h ------------------ original commit in Linus's tree ------------------ From a3d8f0a7f5e8b193db509c7191fefeed3533fc44 Mon Sep 17 00:00:00 2001 From: LongPing Wei <weilongping(a)oppo.com> Date: Thu, 17 Apr 2025 11:07:38 +0800 Subject: [PATCH] dm-bufio: don't schedule in atomic context A BUG was reported as below when CONFIG_DEBUG_ATOMIC_SLEEP and try_verify_in_tasklet are enabled. [ 129.444685][ T934] BUG: sleeping function called from invalid context at drivers/md/dm-bufio.c:2421 [ 129.444723][ T934] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 934, name: kworker/1:4 [ 129.444740][ T934] preempt_count: 201, expected: 0 [ 129.444756][ T934] RCU nest depth: 0, expected: 0 [ 129.444781][ T934] Preemption disabled at: [ 129.444789][ T934] [<ffffffd816231900>] shrink_work+0x21c/0x248 [ 129.445167][ T934] kernel BUG at kernel/sched/walt/walt_debug.c:16! [ 129.445183][ T934] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP [ 129.445204][ T934] Skip md ftrace buffer dump for: 0x1609e0 [ 129.447348][ T934] CPU: 1 PID: 934 Comm: kworker/1:4 Tainted: G W OE 6.6.56-android15-8-o-g6f82312b30b9-debug #1 1400000003000000474e5500b3187743670464e8 [ 129.447362][ T934] Hardware name: Qualcomm Technologies, Inc. Parrot QRD, Alpha-M (DT) [ 129.447373][ T934] Workqueue: dm_bufio_cache shrink_work [ 129.447394][ T934] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 129.447406][ T934] pc : android_rvh_schedule_bug+0x0/0x8 [sched_walt_debug] [ 129.447435][ T934] lr : __traceiter_android_rvh_schedule_bug+0x44/0x6c [ 129.447451][ T934] sp : ffffffc0843dbc90 [ 129.447459][ T934] x29: ffffffc0843dbc90 x28: ffffffffffffffff x27: 0000000000000c8b [ 129.447479][ T934] x26: 0000000000000040 x25: ffffff804b3d6260 x24: ffffffd816232b68 [ 129.447497][ T934] x23: ffffff805171c5b4 x22: 0000000000000000 x21: ffffffd816231900 [ 129.447517][ T934] x20: ffffff80306ba898 x19: 0000000000000000 x18: ffffffc084159030 [ 129.447535][ T934] x17: 00000000d2b5dd1f x16: 00000000d2b5dd1f x15: ffffffd816720358 [ 129.447554][ T934] x14: 0000000000000004 x13: ffffff89ef978000 x12: 0000000000000003 [ 129.447572][ T934] x11: ffffffd817a823c4 x10: 0000000000000202 x9 : 7e779c5735de9400 [ 129.447591][ T934] x8 : ffffffd81560d004 x7 : 205b5d3938373434 x6 : ffffffd8167397c8 [ 129.447610][ T934] x5 : 0000000000000000 x4 : 0000000000000001 x3 : ffffffc0843db9e0 [ 129.447629][ T934] x2 : 0000000000002f15 x1 : 0000000000000000 x0 : 0000000000000000 [ 129.447647][ T934] Call trace: [ 129.447655][ T934] android_rvh_schedule_bug+0x0/0x8 [sched_walt_debug 1400000003000000474e550080cce8a8a78606b6] [ 129.447681][ T934] __might_resched+0x190/0x1a8 [ 129.447694][ T934] shrink_work+0x180/0x248 [ 129.447706][ T934] process_one_work+0x260/0x624 [ 129.447718][ T934] worker_thread+0x28c/0x454 [ 129.447729][ T934] kthread+0x118/0x158 [ 129.447742][ T934] ret_from_fork+0x10/0x20 [ 129.447761][ T934] Code: ???????? ???????? ???????? d2b5dd1f (d4210000) [ 129.447772][ T934] ---[ end trace 0000000000000000 ]--- dm_bufio_lock will call spin_lock_bh when try_verify_in_tasklet is enabled, and __scan will be called in atomic context. Fixes: 7cd326747f46 ("dm bufio: remove dm_bufio_cond_resched()") Signed-off-by: LongPing Wei <weilongping(a)oppo.com> Cc: stable(a)vger.kernel.org Signed-off-by: Mikulas Patocka <mpatocka(a)redhat.com> diff --git a/drivers/md/dm-bufio.c b/drivers/md/dm-bufio.c index 9c8ed65cd87e..f0b5a6931161 100644 --- a/drivers/md/dm-bufio.c +++ b/drivers/md/dm-bufio.c @@ -68,6 +68,8 @@ #define LIST_DIRTY 1 #define LIST_SIZE 2 +#define SCAN_RESCHED_CYCLE 16 + /*--------------------------------------------------------------*/ /* @@ -2424,7 +2426,12 @@ static void __scan(struct dm_bufio_client *c) atomic_long_dec(&c->need_shrink); freed++; - cond_resched(); + + if (unlikely(freed % SCAN_RESCHED_CYCLE == 0)) { + dm_bufio_unlock(c); + cond_resched(); + dm_bufio_lock(c); + } } } }

4 months, 2 weeks

2
1
0 0

Linux 6.12.27

by Greg Kroah-Hartman

I'm announcing the release of the 6.12.27 kernel. This fixes a build problem in the 6.12.26 release. If you do not have a build issue with 6.12.26, there is no need to update. The updated 6.12.y git tree can be found at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git linux-6.12.y and can be browsed at the normal kernel.org git web browser: https://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=summary thanks, greg k-h ------------ Makefile | 2 +- kernel/bpf/preload/bpf_preload_kern.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) Greg Kroah-Hartman (1): Linux 6.12.27 Xi Ruoyao (1): bpf: Fix BPF_INTERNAL namespace import

4 months, 2 weeks

1
1
0 0

Linux 6.1.137

by Greg Kroah-Hartman

I'm announcing the release of the 6.1.137 kernel. This release fixes a problem building the Loongarch target in the 6.1.136 release. If you do not have build problems with the 6.1.136 release, there is no need for you to update to this release. The updated 6.1.y git tree can be found at: git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git linux-6.1.y and can be browsed at the normal kernel.org git web browser: https://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=summary thanks, greg k-h ------------ Makefile | 2 +- arch/loongarch/mm/hugetlbpage.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) Greg Kroah-Hartman (1): Linux 6.1.137 Huacai Chen (1): LoongArch: Fix build error due to backport

4 months, 2 weeks

1
1
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror May 2025