- Linux-stable-mirror - lists.linaro.org

[PATCH 1/2] arm64: dts: stratix10: Support Ethernet Jumbo frame

by Dinh Nguyen

From: Thor Thayer <thor.thayer(a)linux.intel.com> commit a27460c9768ee19949c5b91f3d959ccd88c2a64a upstream Properly specify the RX and TX FIFO size which is important for Jumbo frames. Update the max-frame-size to support Jumbo frames. Signed-off-by: Thor Thayer <thor.thayer(a)linux.intel.com> Signed-off-by: David S. Miller <davem(a)davemloft.net> --- arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 6 ++++++ arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts | 2 +- 2 files changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi index d033da401c26..8a2641c742ae 100644 --- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi @@ -137,6 +137,8 @@ reset-names = "stmmaceth", "stmmaceth-ocp"; clocks = <&clkmgr STRATIX10_EMAC0_CLK>; clock-names = "stmmaceth"; + tx-fifo-depth = <16384>; + rx-fifo-depth = <16384>; status = "disabled"; }; @@ -150,6 +152,8 @@ reset-names = "stmmaceth", "stmmaceth-ocp"; clocks = <&clkmgr STRATIX10_EMAC1_CLK>; clock-names = "stmmaceth"; + tx-fifo-depth = <16384>; + rx-fifo-depth = <16384>; status = "disabled"; }; @@ -163,6 +167,8 @@ reset-names = "stmmaceth", "stmmaceth-ocp"; clocks = <&clkmgr STRATIX10_EMAC2_CLK>; clock-names = "stmmaceth"; + tx-fifo-depth = <16384>; + rx-fifo-depth = <16384>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts index 6edc4fa9fd42..7c661753bfaf 100644 --- a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts @@ -76,7 +76,7 @@ phy-mode = "rgmii"; phy-handle = <&phy0>; - max-frame-size = <3800>; + max-frame-size = <9000>; mdio0 { #address-cells = <1>; -- 2.17.1

6 years, 9 months

3
4
0 0

[PATCH v2] ubifs: Handle re-linking of inodes correctly while recovery

by Richard Weinberger

UBIFS's recovery code strictly assumes that a deleted inode will never come back, therefore it removes all data which belongs to that inode as soon it faces an inode with link count 0 in the replay list. Before O_TMPFILE this assumption was perfectly fine. With O_TMPFILE it can lead to data loss upon a power-cut. Consider a journal with entries like: 0: inode X (nlink = 0) /* O_TMPFILE was created */ 1: data for inode X /* Someone writes to the temp file */ 2: inode X (nlink = 0) /* inode was changed, xattr, chmod, … */ 3: inode X (nlink = 1) /* inode was re-linked via linkat() */ Upon replay of entry #2 UBIFS will drop all data that belongs to inode X, this will lead to an empty file after mounting. As solution for this problem, scan the replay list for a re-link entry before dropping data. Fixes: 474b93704f32 ("ubifs: Implement O_TMPFILE") Cc: stable(a)vger.kernel.org Cc: Russell Senior <russell(a)personaltelco.net> Cc: Rafał Miłecki <zajec5(a)gmail.com> Reported-by: Russell Senior <russell(a)personaltelco.net> Reported-by: Rafał Miłecki <zajec5(a)gmail.com> Signed-off-by: Richard Weinberger <richard(a)nod.at> --- fs/ubifs/replay.c | 37 +++++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/fs/ubifs/replay.c b/fs/ubifs/replay.c index 75f961c4c044..cb1f23459553 100644 --- a/fs/ubifs/replay.c +++ b/fs/ubifs/replay.c @@ -212,6 +212,38 @@ static int trun_remove_range(struct ubifs_info *c, struct replay_entry *r) return ubifs_tnc_remove_range(c, &min_key, &max_key); } +/** + * inode_still_linked - check whether inode in question will be re-linked. + * @c: UBIFS file-system description object + * @rino: replay entry to test + * + * O_TMPFILE files can be re-linked, this means link count goes from 0 to 1. + * This case needs special care, otherwise all references to the inode will + * be removed upon the first replay entry of an inode with link count 0 + * is found. + */ +static bool inode_still_linked(struct ubifs_info *c, struct replay_entry *rino) +{ + struct replay_entry *r; + + ubifs_assert(c, rino->deletion); + ubifs_assert(c, key_type(c, &rino->key) == UBIFS_INO_KEY); + + /* + * Find the most recent entry for the inode behind @rino and check + * whether it is a deletion. + */ + list_for_each_entry_reverse(r, &c->replay_list, list) { + ubifs_assert(c, r->sqnum >= rino->sqnum); + if (key_inum(c, &r->key) == key_inum(c, &rino->key)) + return r->deletion == 0; + + } + + ubifs_assert(c, 0); + return false; +} + /** * apply_replay_entry - apply a replay entry to the TNC. * @c: UBIFS file-system description object @@ -239,6 +271,11 @@ static int apply_replay_entry(struct ubifs_info *c, struct replay_entry *r) { ino_t inum = key_inum(c, &r->key); + if (inode_still_linked(c, r)) { + err = 0; + break; + } + err = ubifs_tnc_remove_ino(c, inum); break; } -- 2.19.1

6 years, 9 months

2
1
0 0

[PATCH v3] drm/msm: Move fence put to where failure occurs

by Robert Foss

If dma_fence_wait fails to wait for a supplied in-fence in msm_ioctl_gem_submit, make sure we release that in-fence. Also remove this dma_fence_put() from the 'out' label. Signed-off-by: Robert Foss <robert.foss(a)collabora.com> Reviewed-by: Chris Wilson <chris(a)chris-wilson.co.uk> Cc: stable(a)vger.kernel.org --- Changes since v2: - Chris Wilson: Added r-b and stable kernel tag Changes since v1: - Chris Wilson: Make sure that dma_fence_put() is always executed drivers/gpu/drm/msm/msm_gem_submit.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/drivers/gpu/drm/msm/msm_gem_submit.c b/drivers/gpu/drm/msm/msm_gem_submit.c index a90aedd6883a..d5e6665a4c8f 100644 --- a/drivers/gpu/drm/msm/msm_gem_submit.c +++ b/drivers/gpu/drm/msm/msm_gem_submit.c @@ -411,7 +411,6 @@ int msm_ioctl_gem_submit(struct drm_device *dev, void *data, struct msm_file_private *ctx = file->driver_priv; struct msm_gem_submit *submit; struct msm_gpu *gpu = priv->gpu; - struct dma_fence *in_fence = NULL; struct sync_file *sync_file = NULL; struct msm_gpu_submitqueue *queue; struct msm_ringbuffer *ring; @@ -444,6 +443,8 @@ int msm_ioctl_gem_submit(struct drm_device *dev, void *data, ring = gpu->rb[queue->prio]; if (args->flags & MSM_SUBMIT_FENCE_FD_IN) { + struct dma_fence *in_fence; + in_fence = sync_file_get_fence(args->fence_fd); if (!in_fence) @@ -453,11 +454,13 @@ int msm_ioctl_gem_submit(struct drm_device *dev, void *data, * Wait if the fence is from a foreign context, or if the fence * array contains any fence from a foreign context. */ - if (!dma_fence_match_context(in_fence, ring->fctx->context)) { + ret = 0; + if (!dma_fence_match_context(in_fence, ring->fctx->context)) ret = dma_fence_wait(in_fence, true); - if (ret) - return ret; - } + + dma_fence_put(in_fence); + if (ret) + return ret; } ret = mutex_lock_interruptible(&dev->struct_mutex); @@ -583,8 +586,6 @@ int msm_ioctl_gem_submit(struct drm_device *dev, void *data, } out: - if (in_fence) - dma_fence_put(in_fence); submit_cleanup(submit); if (ret) msm_gem_submit_free(submit); -- 2.17.1

6 years, 9 months

1
1
0 0

[PATCH v3 2/2] drm/vc4: Set ->legacy_cursor_update to false when doing non-async updates

by Boris Brezillon

drm_atomic_helper_setup_commit() auto-completes commit->flip_done when state->legacy_cursor_update is true, but we know for sure that we want a sync update when we call drm_atomic_helper_setup_commit() from vc4_atomic_commit(). Explicitly set state->legacy_cursor_update to false to prevent this auto-completion. Fixes: 184d3cf4f738 ("drm/vc4: Use wait_for_flip_done() instead of wait_for_vblanks()") Cc: <stable(a)vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon(a)bootlin.com> Reviewed-by: Eric Anholt <eric(a)anholt.net> --- Changes in v3: - Add missing Fixes and Cc-stable tags - Fix a typo in the commit message Changes in v2: - Add Eric's R-b --- drivers/gpu/drm/vc4/vc4_kms.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c index 127468785f74..1f94b9affe4b 100644 --- a/drivers/gpu/drm/vc4/vc4_kms.c +++ b/drivers/gpu/drm/vc4/vc4_kms.c @@ -214,6 +214,12 @@ static int vc4_atomic_commit(struct drm_device *dev, return 0; } + /* We know for sure we don't want an async update here. Set + * state->legacy_cursor_update to false to prevent + * drm_atomic_helper_setup_commit() from auto-completing + * commit->flip_done. + */ + state->legacy_cursor_update = false; ret = drm_atomic_helper_setup_commit(state, nonblock); if (ret) return ret; -- 2.17.1

6 years, 9 months

1
0
0 0

[PATCH 1/1] xhci: Prevent bus suspend if a port connect change or polling state is detected

by Mathias Nyman

USB3 roothub might autosuspend before a plugged USB3 device is detected, causing USB3 device enumeration failure. USB3 devices don't show up as connected and enabled until USB3 link trainig completes. On a fast booting platform with a slow USB3 link training the link might reach the connected enabled state just as the bus is suspending. If this device is discovered first time by the xhci_bus_suspend() routine it will be put to U3 suspended state like the other ports which failed to suspend earlier. The hub thread will notice the connect change and resume the bus, moving the port back to U0 This U0 -> U3 -> U0 transition right after being connected seems to be too much for some devices, causing them to first go to SS.Inactive state, and finally end up stuck in a polling state with reset asserted Fix this by failing the bus suspend if a port has a connect change or is in a polling state in xhci_bus_suspend(). Don't do any port changes until all ports are checked, buffer all port changes and only write them in the end if suspend can proceed Cc: stable(a)vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman(a)linux.intel.com> --- drivers/usb/host/xhci-hub.c | 60 ++++++++++++++++++++++++++++++++++----------- 1 file changed, 46 insertions(+), 14 deletions(-) diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c index da98a11..94aca1b 100644 --- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -1474,15 +1474,18 @@ int xhci_bus_suspend(struct usb_hcd *hcd) unsigned long flags; struct xhci_hub *rhub; struct xhci_port **ports; + u32 portsc_buf[USB_MAXCHILDREN]; + bool wake_enabled; rhub = xhci_get_rhub(hcd); ports = rhub->ports; max_ports = rhub->num_ports; bus_state = &xhci->bus_state[hcd_index(hcd)]; + wake_enabled = hcd->self.root_hub->do_remote_wakeup; spin_lock_irqsave(&xhci->lock, flags); - if (hcd->self.root_hub->do_remote_wakeup) { + if (wake_enabled) { if (bus_state->resuming_ports || /* USB2 */ bus_state->port_remote_wakeup) { /* USB3 */ spin_unlock_irqrestore(&xhci->lock, flags); @@ -1490,26 +1493,36 @@ int xhci_bus_suspend(struct usb_hcd *hcd) return -EBUSY; } } - - port_index = max_ports; + /* + * Prepare ports for suspend, but don't write anything before all ports + * are checked and we know bus suspend can proceed + */ bus_state->bus_suspended = 0; + port_index = max_ports; while (port_index--) { - /* suspend the port if the port is not suspended */ u32 t1, t2; - int slot_id; t1 = readl(ports[port_index]->addr); t2 = xhci_port_state_to_neutral(t1); + portsc_buf[port_index] = 0; - if ((t1 & PORT_PE) && !(t1 & PORT_PLS_MASK)) { - xhci_dbg(xhci, "port %d not suspended\n", port_index); - slot_id = xhci_find_slot_id_by_port(hcd, xhci, - port_index + 1); - if (slot_id) { + /* Bail out if a USB3 port has a new device in link training */ + if ((t1 & PORT_PLS_MASK) == XDEV_POLLING) { + bus_state->bus_suspended = 0; + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_dbg(xhci, "Bus suspend bailout, port in polling\n"); + return -EBUSY; + } + + /* suspend ports in U0, or bail out for new connect changes */ + if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) { + if ((t1 & PORT_CSC) && wake_enabled) { + bus_state->bus_suspended = 0; spin_unlock_irqrestore(&xhci->lock, flags); - xhci_stop_device(xhci, slot_id, 1); - spin_lock_irqsave(&xhci->lock, flags); + xhci_dbg(xhci, "Bus suspend bailout, port connect change\n"); + return -EBUSY; } + xhci_dbg(xhci, "port %d not suspended\n", port_index); t2 &= ~PORT_PLS_MASK; t2 |= PORT_LINK_STROBE | XDEV_U3; set_bit(port_index, &bus_state->bus_suspended); @@ -1518,7 +1531,7 @@ int xhci_bus_suspend(struct usb_hcd *hcd) * including the USB 3.0 roothub, but only if CONFIG_PM * is enabled, so also enable remote wake here. */ - if (hcd->self.root_hub->do_remote_wakeup) { + if (wake_enabled) { if (t1 & PORT_CONNECT) { t2 |= PORT_WKOC_E | PORT_WKDISC_E; t2 &= ~PORT_WKCONN_E; @@ -1538,7 +1551,26 @@ int xhci_bus_suspend(struct usb_hcd *hcd) t1 = xhci_port_state_to_neutral(t1); if (t1 != t2) - writel(t2, ports[port_index]->addr); + portsc_buf[port_index] = t2; + } + + /* write port settings, stopping and suspending ports if needed */ + port_index = max_ports; + while (port_index--) { + if (!portsc_buf[port_index]) + continue; + if (test_bit(port_index, &bus_state->bus_suspended)) { + int slot_id; + + slot_id = xhci_find_slot_id_by_port(hcd, xhci, + port_index + 1); + if (slot_id) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_stop_device(xhci, slot_id, 1); + spin_lock_irqsave(&xhci->lock, flags); + } + } + writel(portsc_buf[port_index], ports[port_index]->addr); } hcd->state = HC_STATE_SUSPENDED; bus_state->next_statechange = jiffies + msecs_to_jiffies(10); -- 2.7.4

6 years, 9 months

1
0
0 0

[PATCH V5 5/8] MIPS: Align kernel load address to 64KB

by Huacai Chen

KEXEC needs the new kernel's load address to be aligned on a page boundary (see sanity_check_segment_list()), but on MIPS the default vmlinuz load address is only explicitly aligned to 16 bytes. Since the largest PAGE_SIZE supported by MIPS kernels is 64KB, increase the alignment calculated by calc_vmlinuz_load_addr to 64KB. Cc: <stable(a)vger.kernel.org> # 2.6.36+ Signed-off-by: Huacai Chen <chenhc(a)lemote.com> --- arch/mips/boot/compressed/calc_vmlinuz_load_addr.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c b/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c index 37fe58c..542c3ed 100644 --- a/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c +++ b/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c @@ -13,6 +13,7 @@ #include <stdint.h> #include <stdio.h> #include <stdlib.h> +#include "../../../../include/linux/sizes.h" int main(int argc, char *argv[]) { @@ -45,11 +46,11 @@ int main(int argc, char *argv[]) vmlinuz_load_addr = vmlinux_load_addr + vmlinux_size; /* - * Align with 16 bytes: "greater than that used for any standard data - * types by a MIPS compiler." -- See MIPS Run Linux (Second Edition). + * Align with 64KB: KEXEC needs load sections to be aligned to PAGE_SIZE, + * which may be as large as 64KB depending on the kernel configuration. */ - vmlinuz_load_addr += (16 - vmlinux_size % 16); + vmlinuz_load_addr += (SZ_64K - vmlinux_size % SZ_64K); printf("0x%llx\n", vmlinuz_load_addr); -- 2.7.0

6 years, 9 months

1
0
0 0

[PATCH V5 3/8] MIPS: Ensure pmd_present() returns false after pmd_mknotpresent()

by Huacai Chen

This patch is borrowed from ARM64 to ensure pmd_present() returns false after pmd_mknotpresent(). This is needed for THP. Cc: <stable(a)vger.kernel.org> # 3.8+ References: 5bb1cc0ff9a6 ("arm64: Ensure pmd_present() returns false after pmd_mknotpresent()") Reviewed-by: James Hogan <jhogan(a)kernel.org> Signed-off-by: Huacai Chen <chenhc(a)lemote.com> --- arch/mips/include/asm/pgtable-64.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/mips/include/asm/pgtable-64.h b/arch/mips/include/asm/pgtable-64.h index 0036ea0..93a9dce 100644 --- a/arch/mips/include/asm/pgtable-64.h +++ b/arch/mips/include/asm/pgtable-64.h @@ -265,6 +265,11 @@ static inline int pmd_bad(pmd_t pmd) static inline int pmd_present(pmd_t pmd) { +#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT + if (unlikely(pmd_val(pmd) & _PAGE_HUGE)) + return pmd_val(pmd) & _PAGE_PRESENT; +#endif + return pmd_val(pmd) != (unsigned long) invalid_pte_table; } -- 2.7.0

6 years, 9 months

1
0
0 0

[PATCH V5 2/8] MIPS: c-r4k: Add r4k_blast_scache_node for Loongson-3

by Huacai Chen

For multi-node Loongson-3 (NUMA configuration), r4k_blast_scache() can only flush Node-0's scache. So we add r4k_blast_scache_node() by using (CAC_BASE | (node_id << NODE_ADDRSPACE_SHIFT)) instead of CKSEG0 as the start address. Cc: <stable(a)vger.kernel.org> # 3.15+ Signed-off-by: Huacai Chen <chenhc(a)lemote.com> --- arch/mips/include/asm/mach-loongson64/mmzone.h | 1 + arch/mips/include/asm/mmzone.h | 8 +++++ arch/mips/include/asm/r4kcache.h | 25 +++++++++++++++ arch/mips/mm/c-r4k.c | 44 ++++++++++++++++++++++---- 4 files changed, 71 insertions(+), 7 deletions(-) diff --git a/arch/mips/include/asm/mach-loongson64/mmzone.h b/arch/mips/include/asm/mach-loongson64/mmzone.h index c9f7e23..59c8b11 100644 --- a/arch/mips/include/asm/mach-loongson64/mmzone.h +++ b/arch/mips/include/asm/mach-loongson64/mmzone.h @@ -21,6 +21,7 @@ #define NODE3_ADDRSPACE_OFFSET 0x300000000000UL #define pa_to_nid(addr) (((addr) & 0xf00000000000) >> NODE_ADDRSPACE_SHIFT) +#define nid_to_addrbase(nid) ((nid) << NODE_ADDRSPACE_SHIFT) #define LEVELS_PER_SLICE 128 diff --git a/arch/mips/include/asm/mmzone.h b/arch/mips/include/asm/mmzone.h index f085fba..2a0fe1d 100644 --- a/arch/mips/include/asm/mmzone.h +++ b/arch/mips/include/asm/mmzone.h @@ -9,6 +9,14 @@ #include <asm/page.h> #include <mmzone.h> +#ifndef pa_to_nid +#define pa_to_nid(addr) 0 +#endif + +#ifndef nid_to_addrbase +#define nid_to_addrbase(nid) 0 +#endif + #ifdef CONFIG_DISCONTIGMEM #define pfn_to_nid(pfn) pa_to_nid((pfn) << PAGE_SHIFT) diff --git a/arch/mips/include/asm/r4kcache.h b/arch/mips/include/asm/r4kcache.h index d19b2d6..0815c2a 100644 --- a/arch/mips/include/asm/r4kcache.h +++ b/arch/mips/include/asm/r4kcache.h @@ -674,4 +674,25 @@ __BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, , ) __BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, , ) __BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, , ) +/* Currently, this is very specific to Loongson-3 */ +#define __BUILD_BLAST_CACHE_NODE(pfx, desc, indexop, hitop, lsize) \ +static inline void blast_##pfx##cache##lsize##_node(long node) \ +{ \ + unsigned long start = CAC_BASE | nid_to_addrbase(node); \ + unsigned long end = start + current_cpu_data.desc.waysize; \ + unsigned long ws_inc = 1UL << current_cpu_data.desc.waybit; \ + unsigned long ws_end = current_cpu_data.desc.ways << \ + current_cpu_data.desc.waybit; \ + unsigned long ws, addr; \ + \ + for (ws = 0; ws < ws_end; ws += ws_inc) \ + for (addr = start; addr < end; addr += lsize * 32) \ + cache##lsize##_unroll32(addr|ws, indexop); \ +} + +__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16) +__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32) +__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64) +__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128) + #endif /* _ASM_R4KCACHE_H */ diff --git a/arch/mips/mm/c-r4k.c b/arch/mips/mm/c-r4k.c index 7e430b4..96d666a 100644 --- a/arch/mips/mm/c-r4k.c +++ b/arch/mips/mm/c-r4k.c @@ -459,11 +459,28 @@ static void r4k_blast_scache_setup(void) r4k_blast_scache = blast_scache128; } +static void (*r4k_blast_scache_node)(long node); + +static void r4k_blast_scache_node_setup(void) +{ + unsigned long sc_lsize = cpu_scache_line_size(); + + if (current_cpu_type() != CPU_LOONGSON3) + r4k_blast_scache_node = (void *)cache_noop; + else if (sc_lsize == 16) + r4k_blast_scache_node = blast_scache16_node; + else if (sc_lsize == 32) + r4k_blast_scache_node = blast_scache32_node; + else if (sc_lsize == 64) + r4k_blast_scache_node = blast_scache64_node; + else if (sc_lsize == 128) + r4k_blast_scache_node = blast_scache128_node; +} + static inline void local_r4k___flush_cache_all(void * args) { switch (current_cpu_type()) { case CPU_LOONGSON2: - case CPU_LOONGSON3: case CPU_R4000SC: case CPU_R4000MC: case CPU_R4400SC: @@ -480,6 +497,11 @@ static inline void local_r4k___flush_cache_all(void * args) r4k_blast_scache(); break; + case CPU_LOONGSON3: + /* Use get_ebase_cpunum() for both NUMA=y/n */ + r4k_blast_scache_node(get_ebase_cpunum() >> 2); + break; + case CPU_BMIPS5000: r4k_blast_scache(); __sync(); @@ -840,10 +862,14 @@ static void r4k_dma_cache_wback_inv(unsigned long addr, unsigned long size) preempt_disable(); if (cpu_has_inclusive_pcaches) { - if (size >= scache_size) - r4k_blast_scache(); - else + if (size >= scache_size) { + if (current_cpu_type() != CPU_LOONGSON3) + r4k_blast_scache(); + else + r4k_blast_scache_node(pa_to_nid(addr)); + } else { blast_scache_range(addr, addr + size); + } preempt_enable(); __sync(); return; @@ -877,9 +903,12 @@ static void r4k_dma_cache_inv(unsigned long addr, unsigned long size) preempt_disable(); if (cpu_has_inclusive_pcaches) { - if (size >= scache_size) - r4k_blast_scache(); - else { + if (size >= scache_size) { + if (current_cpu_type() != CPU_LOONGSON3) + r4k_blast_scache(); + else + r4k_blast_scache_node(pa_to_nid(addr)); + } else { /* * There is no clearly documented alignment requirement * for the cache instruction on MIPS processors and @@ -1918,6 +1947,7 @@ void r4k_cache_init(void) r4k_blast_scache_page_setup(); r4k_blast_scache_page_indexed_setup(); r4k_blast_scache_setup(); + r4k_blast_scache_node_setup(); #ifdef CONFIG_EVA r4k_blast_dcache_user_page_setup(); r4k_blast_icache_user_page_setup(); -- 2.7.0

6 years, 9 months

1
0
0 0

FAILED: patch "[PATCH] ovl: fix recursive oi->lock in ovl_link()" failed to apply to 4.18-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.18-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From 6cd078702f2f33cb6b19a682de3e9184112f1a46 Mon Sep 17 00:00:00 2001 From: Amir Goldstein <amir73il(a)gmail.com> Date: Thu, 18 Oct 2018 09:45:49 +0300 Subject: [PATCH] ovl: fix recursive oi->lock in ovl_link() linking a non-copied-up file into a non-copied-up parent results in a nested call to mutex_lock_interruptible(&oi->lock). Fix this by copying up target parent before ovl_nlink_start(), same as done in ovl_rename(). ~/unionmount-testsuite$ ./run --ov -s ~/unionmount-testsuite$ ln /mnt/a/foo100 /mnt/a/dir100/ WARNING: possible recursive locking detected -------------------------------------------- ln/1545 is trying to acquire lock: 00000000bcce7c4c (&ovl_i_lock_key[depth]){+.+.}, at: ovl_copy_up_start+0x28/0x7d but task is already holding lock: 0000000026d73d5b (&ovl_i_lock_key[depth]){+.+.}, at: ovl_nlink_start+0x3c/0xc1 [SzM: this seems to be a false positive, but doing the copy-up first is harmless and removes the lockdep splat] Reported-by: syzbot+3ef5c0d1a5cb0b21e6be(a)syzkaller.appspotmail.com Fixes: 5f8415d6b87e ("ovl: persistent overlay inode nlink for...") Cc: <stable(a)vger.kernel.org> # v4.13 Signed-off-by: Amir Goldstein <amir73il(a)gmail.com> Signed-off-by: Miklos Szeredi <mszeredi(a)redhat.com> diff --git a/fs/overlayfs/dir.c b/fs/overlayfs/dir.c index 276914ae3c60..e1a55ecb7aba 100644 --- a/fs/overlayfs/dir.c +++ b/fs/overlayfs/dir.c @@ -663,6 +663,10 @@ static int ovl_link(struct dentry *old, struct inode *newdir, if (err) goto out_drop_write; + err = ovl_copy_up(new->d_parent); + if (err) + goto out_drop_write; + if (ovl_is_metacopy_dentry(old)) { err = ovl_set_redirect(old, false); if (err)

6 years, 9 months

3
2
0 0

stable-rc/linux-4.4.y boot: 65 boots: 1 failed, 50 passed with 14 offline (v4.4.163-107-g3c957d7bc2fc)

by kernelci.org bot

stable-rc/linux-4.4.y boot: 65 boots: 1 failed, 50 passed with 14 offline (v4.4.163-107-g3c957d7bc2fc) Full Boot Summary: https://kernelci.org/boot/all/job/stable-rc/branch/linux-4.4.y/kernel/v4.4.… Full Build Summary: https://kernelci.org/build/stable-rc/branch/linux-4.4.y/kernel/v4.4.163-107… Tree: stable-rc Branch: linux-4.4.y Git Describe: v4.4.163-107-g3c957d7bc2fc Git Commit: 3c957d7bc2fc9c7bbe5200a2b7f0d6fc7bd391c0 Git URL: http://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git Tested: 37 unique boards, 18 SoC families, 15 builds out of 178 Boot Failure Detected: arm: multi_v7_defconfig stih410-b2120: 1 failed lab Offline Platforms: arm: omap2plus_defconfig: am335x-boneblack: 1 offline lab sunxi_defconfig: sun5i-r8-chip: 1 offline lab tegra_defconfig: tegra124-jetson-tk1: 1 offline lab bcm2835_defconfig: bcm2835-rpi-b: 1 offline lab exynos_defconfig: exynos5800-peach-pi: 1 offline lab sama5_defconfig: at91-sama5d4_xplained: 1 offline lab multi_v7_defconfig: alpine-db: 1 offline lab am335x-boneblack: 1 offline lab at91-sama5d4_xplained: 1 offline lab exynos5800-peach-pi: 1 offline lab socfpga_cyclone5_de0_sockit: 1 offline lab sun5i-r8-chip: 1 offline lab tegra124-jetson-tk1: 1 offline lab arm64: defconfig: apq8016-sbc: 1 offline lab --- For more info write to <info(a)kernelci.org>

6 years, 9 months

1
0
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror