- Linux-stable-mirror - lists.linaro.org

[PATCH 04/12] can: m_can: Fix runtime resume call

by Marc Kleine-Budde

From: Faiz Abbas <faiz_abbas(a)ti.com> pm_runtime_get_sync() returns a 1 if the state of the device is already 'active'. This is not a failure case and should return a success. Therefore fix error handling for pm_runtime_get_sync() call such that it returns success when the value is 1. Also cleanup the TODO for using runtime PM for sleep mode as that is implemented. Signed-off-by: Faiz Abbas <faiz_abbas(a)ti.com> Cc: <stable(a)vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl(a)pengutronix.de> --- drivers/net/can/m_can/m_can.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c index 8e2b7f873c4d..e2f965c2e3aa 100644 --- a/drivers/net/can/m_can/m_can.c +++ b/drivers/net/can/m_can/m_can.c @@ -634,10 +634,12 @@ static int m_can_clk_start(struct m_can_priv *priv) int err; err = pm_runtime_get_sync(priv->device); - if (err) + if (err < 0) { pm_runtime_put_noidle(priv->device); + return err; + } - return err; + return 0; } static void m_can_clk_stop(struct m_can_priv *priv) @@ -1688,8 +1690,6 @@ static int m_can_plat_probe(struct platform_device *pdev) return ret; } -/* TODO: runtime PM with power down or sleep mode */ - static __maybe_unused int m_can_suspend(struct device *dev) { struct net_device *ndev = dev_get_drvdata(dev); -- 2.18.0

6 years, 12 months

1
0
0 0

[PATCH 02/12] can: m_can.c: fix setup of CCCR register: clear CCCR NISO bit before checking can.ctrlmode

by Marc Kleine-Budde

From: Roman Fietze <roman.fietze(a)telemotive.de> Inside m_can_chip_config(), when setting up the new value of the CCCR, the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON, CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for CAN_CTRLMODE_FD_NON_ISO. This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO, this mode could never be cleared again. This fix is only relevant for controllers with version 3.1.x or 3.2.x. Older versions do not support NISO. Signed-off-by: Roman Fietze <roman.fietze(a)telemotive.de> Cc: linux-stable <stable(a)vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl(a)pengutronix.de> --- drivers/net/can/m_can/m_can.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c index b397a33f3d32..8e2b7f873c4d 100644 --- a/drivers/net/can/m_can/m_can.c +++ b/drivers/net/can/m_can/m_can.c @@ -1109,7 +1109,8 @@ static void m_can_chip_config(struct net_device *dev) } else { /* Version 3.1.x or 3.2.x */ - cccr &= ~(CCCR_TEST | CCCR_MON | CCCR_BRSE | CCCR_FDOE); + cccr &= ~(CCCR_TEST | CCCR_MON | CCCR_BRSE | CCCR_FDOE | + CCCR_NISO); /* Only 3.2.x has NISO Bit implemented */ if (priv->can.ctrlmode & CAN_CTRLMODE_FD_NON_ISO) -- 2.18.0

6 years, 12 months

1
0
0 0

[PATCH 01/12] can: peak_canfd: fix firmware < v3.3.0: limit allocation to 32-bit DMA addr only

by Marc Kleine-Budde

From: Stephane Grosjean <s.grosjean(a)peak-system.com> The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards family is not capable of handling a mix of 32-bit and 64-bit logical addresses. If the board is equipped with 2 or 4 CAN ports, then such a situation might lead to a PCIe Bus Error "Malformed TLP" packet as well as "irq xx: nobody cared" issue. This patch adds a workaround that requests only 32-bit DMA addresses when these might be allocated outside of the 4 GB area. This issue has been fixed in firmware v3.3.0 and next. Signed-off-by: Stephane Grosjean <s.grosjean(a)peak-system.com> Cc: linux-stable <stable(a)vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl(a)pengutronix.de> --- drivers/net/can/peak_canfd/peak_pciefd_main.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/drivers/net/can/peak_canfd/peak_pciefd_main.c b/drivers/net/can/peak_canfd/peak_pciefd_main.c index b9e28578bc7b..455a3797a200 100644 --- a/drivers/net/can/peak_canfd/peak_pciefd_main.c +++ b/drivers/net/can/peak_canfd/peak_pciefd_main.c @@ -58,6 +58,10 @@ MODULE_LICENSE("GPL v2"); #define PCIEFD_REG_SYS_VER1 0x0040 /* version reg #1 */ #define PCIEFD_REG_SYS_VER2 0x0044 /* version reg #2 */ +#define PCIEFD_FW_VERSION(x, y, z) (((u32)(x) << 24) | \ + ((u32)(y) << 16) | \ + ((u32)(z) << 8)) + /* System Control Registers Bits */ #define PCIEFD_SYS_CTL_TS_RST 0x00000001 /* timestamp clock */ #define PCIEFD_SYS_CTL_CLK_EN 0x00000002 /* system clock */ @@ -782,6 +786,21 @@ static int peak_pciefd_probe(struct pci_dev *pdev, "%ux CAN-FD PCAN-PCIe FPGA v%u.%u.%u:\n", can_count, hw_ver_major, hw_ver_minor, hw_ver_sub); +#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT + /* FW < v3.3.0 DMA logic doesn't handle correctly the mix of 32-bit and + * 64-bit logical addresses: this workaround forces usage of 32-bit + * DMA addresses only when such a fw is detected. + */ + if (PCIEFD_FW_VERSION(hw_ver_major, hw_ver_minor, hw_ver_sub) < + PCIEFD_FW_VERSION(3, 3, 0)) { + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); + if (err) + dev_warn(&pdev->dev, + "warning: can't set DMA mask %llxh (err %d)\n", + DMA_BIT_MASK(32), err); + } +#endif + /* stop system clock */ pciefd_sys_writereg(pciefd, PCIEFD_SYS_CTL_CLK_EN, PCIEFD_REG_SYS_CTL_CLR); -- 2.18.0

6 years, 12 months

1
0
0 0

[PATCH 0/6] UBI fixes backported to 4.4.x

by Richard Weinberger

Greg, this series contains backports of the following upstream commits: 243a4f8126fc ubi: Introduce vol_ignored() fdf10ed710c0 ubi: Rework Fastmap attach base code 74f2c6e9a47c ubi: Be more paranoid while seaching for the most recent Fastmap 2e8f08deabbc ubi: Fix races around ubi_refill_pools() f7d11b33d4e8 ubi: Fix Fastmap's update_vol() 5793f39de7f6 ubi: fastmap: Erase outdated anchor PEBs during attach The first two patches are not directly stable patches but the other patches depend on them. Richard Weinberger (5): ubi: Introduce vol_ignored() ubi: Rework Fastmap attach base code ubi: Be more paranoid while seaching for the most recent Fastmap ubi: Fix races around ubi_refill_pools() ubi: Fix Fastmap's update_vol() Sascha Hauer (1): ubi: fastmap: Erase outdated anchor PEBs during attach drivers/mtd/ubi/attach.c | 139 ++++++++++++++++++++++++++--------- drivers/mtd/ubi/eba.c | 4 +- drivers/mtd/ubi/fastmap-wl.c | 6 +- drivers/mtd/ubi/fastmap.c | 51 +++++++++++-- drivers/mtd/ubi/ubi.h | 46 +++++++++++- drivers/mtd/ubi/wl.c | 114 ++++++++++++++++++++++------ 6 files changed, 292 insertions(+), 68 deletions(-) -- 2.18.0

6 years, 12 months

2
10
0 0

[PATCH] drm/i915/gvt: fix cleanup sequence in intel_gvt_clean_device

by hang.yuan＠linux.intel.com

From: Hang Yuan <hang.yuan(a)linux.intel.com> Create one vGPU and then unbind IGD device from i915 driver. The following oops will happen. This patch will free vgpu resource first and then gvt resource to remove these oops. BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 PGD 80000003c9d2c067 P4D 80000003c9d2c067 PUD 3c817c067 P MD 0 Oops: 0002 [#1] SMP PTI RIP: 0010:down_write+0x1b/0x40 Call Trace: debugfs_remove_recursive+0x46/0x1a0 intel_gvt_debugfs_remove_vgpu+0x15/0x30 [i915] intel_gvt_destroy_vgpu+0x2d/0xf0 [i915] intel_vgpu_remove+0x2c/0x30 [kvmgt] mdev_device_remove_ops+0x23/0x50 [mdev] mdev_device_remove+0xdb/0x190 [mdev] mdev_device_remove+0x190/0x190 [mdev] device_for_each_child+0x47/0x90 mdev_unregister_device+0xd5/0x120 [mdev] intel_gvt_clean_device+0x91/0x120 [i915] i915_driver_unload+0x9d/0x120 [i915] i915_pci_remove+0x15/0x20 [i915] pci_device_remove+0x3b/0xc0 device_release_driver_internal+0x157/0x230 unbind_store+0xfc/0x150 kernfs_fop_write+0x10f/0x180 __vfs_write+0x36/0x180 ? common_file_perm+0x41/0x130 ? _cond_resched+0x16/0x40 vfs_write+0xb3/0x1a0 ksys_write+0x52/0xc0 do_syscall_64+0x55/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 BUG: unable to handle kernel NULL pointer dereference at 0 000000000000038 PGD 8000000405bce067 P4D 8000000405bce067 PUD 405bcd067 PM D 0 Oops: 0000 [#1] SMP PTI RIP: 0010:hrtimer_active+0x5/0x40 Call Trace: hrtimer_try_to_cancel+0x25/0x120 ? tbs_sched_clean_vgpu+0x1f/0x50 [i915] hrtimer_cancel+0x15/0x20 intel_gvt_destroy_vgpu+0x4c/0xf0 [i915] intel_vgpu_remove+0x2c/0x30 [kvmgt] mdev_device_remove_ops+0x23/0x50 [mdev] mdev_device_remove+0xdb/0x190 [mdev] ? mdev_device_remove+0x190/0x190 [mdev] device_for_each_child+0x47/0x90 mdev_unregister_device+0xd5/0x120 [mdev] intel_gvt_clean_device+0x89/0x120 [i915] i915_driver_unload+0x9d/0x120 [i915] i915_pci_remove+0x15/0x20 [i915] pci_device_remove+0x3b/0xc0 device_release_driver_internal+0x157/0x230 unbind_store+0xfc/0x150 kernfs_fop_write+0x10f/0x180 __vfs_write+0x36/0x180 ? common_file_perm+0x41/0x130 ? _cond_resched+0x16/0x40 vfs_write+0xb3/0x1a0 ksys_write+0x52/0xc0 do_syscall_64+0x55/0x100 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: bc7b0be316ae("drm/i915/gvt: Add basic debugfs infrastructure") Fixes: afe04fbe6c52("drm/i915/gvt: create an idle vGPU") Signed-off-by: Hang Yuan <hang.yuan(a)linux.intel.com> --- drivers/gpu/drm/i915/gvt/gvt.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) diff --git a/drivers/gpu/drm/i915/gvt/gvt.c b/drivers/gpu/drm/i915/gvt/gvt.c index 4e65266..b96c6c7 100644 --- a/drivers/gpu/drm/i915/gvt/gvt.c +++ b/drivers/gpu/drm/i915/gvt/gvt.c @@ -315,6 +315,11 @@ void intel_gvt_clean_device(struct drm_i915_private *dev_priv) if (WARN_ON(!gvt)) return; + intel_gvt_destroy_idle_vgpu(gvt->idle_vgpu); + intel_gvt_hypervisor_host_exit(&dev_priv->drm.pdev->dev, gvt); + intel_gvt_cleanup_vgpu_type_groups(gvt); + intel_gvt_clean_vgpu_types(gvt); + intel_gvt_debugfs_clean(gvt); clean_service_thread(gvt); intel_gvt_clean_cmd_parser(gvt); @@ -322,17 +327,10 @@ void intel_gvt_clean_device(struct drm_i915_private *dev_priv) intel_gvt_clean_workload_scheduler(gvt); intel_gvt_clean_gtt(gvt); intel_gvt_clean_irq(gvt); - intel_gvt_clean_mmio_info(gvt); intel_gvt_free_firmware(gvt); - - intel_gvt_hypervisor_host_exit(&dev_priv->drm.pdev->dev, gvt); - intel_gvt_cleanup_vgpu_type_groups(gvt); - intel_gvt_clean_vgpu_types(gvt); - + intel_gvt_clean_mmio_info(gvt); idr_destroy(&gvt->vgpu_idr); - intel_gvt_destroy_idle_vgpu(gvt->idle_vgpu); - kfree(dev_priv->gvt); dev_priv->gvt = NULL; } -- 2.7.4

6 years, 12 months

1
0
0 0

request for 4.4-stable: 1dc3039bc87a ("block: do not use interruptible wait anywhere")

by Sudip Mukherjee

Hi Greg, As discussed with Alan, this is the backported patch for 4.4-stable. Please apply it to your queue. -- Regards Sudip

6 years, 12 months

2
1
0 0

FAILED: patch "[PATCH] powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from" failed to apply to 4.14-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 4.14-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. thanks, greg k-h ------------------ original commit in Linus's tree ------------------ >From b03897cf318dfc47de33a7ecbc7655584266f034 Mon Sep 17 00:00:00 2001 From: "Gautham R. Shenoy" <ego(a)linux.vnet.ibm.com> Date: Wed, 18 Jul 2018 14:03:16 +0530 Subject: [PATCH] powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from stop (idle) On 64-bit servers, SPRN_SPRG3 and its userspace read-only mirror SPRN_USPRG3 are used as userspace VDSO write and read registers respectively. SPRN_SPRG3 is lost when we enter stop4 and above, and is currently not restored. As a result, any read from SPRN_USPRG3 returns zero on an exit from stop4 (Power9 only) and above. Thus in this situation, on POWER9, any call from sched_getcpu() always returns zero, as on powerpc, we call __kernel_getcpu() which relies upon SPRN_USPRG3 to report the CPU and NUMA node information. Fix this by restoring SPRN_SPRG3 on wake up from a deep stop state with the sprg_vdso value that is cached in PACA. Fixes: e1c1cfed5432 ("powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle") Cc: stable(a)vger.kernel.org # v4.14+ Reported-by: Florian Weimer <fweimer(a)redhat.com> Signed-off-by: Gautham R. Shenoy <ego(a)linux.vnet.ibm.com> Reviewed-by: Michael Ellerman <mpe(a)ellerman.id.au> Signed-off-by: Michael Ellerman <mpe(a)ellerman.id.au> diff --git a/arch/powerpc/kernel/idle_book3s.S b/arch/powerpc/kernel/idle_book3s.S index e734f6e45abc..689306118b48 100644 --- a/arch/powerpc/kernel/idle_book3s.S +++ b/arch/powerpc/kernel/idle_book3s.S @@ -144,7 +144,9 @@ power9_restore_additional_sprs: mtspr SPRN_MMCR1, r4 ld r3, STOP_MMCR2(r13) + ld r4, PACA_SPRG_VDSO(r13) mtspr SPRN_MMCR2, r3 + mtspr SPRN_SPRG3, r4 blr /*

6 years, 12 months

4
4
0 0

Re: [RESEND] stable request: 4.4.y: 797097301860 ("clk: tegra: Fix PLL_U post divider and initial rate on Tegra30")

by Jon Hunter

Correcting the stable ML address ... On 23/07/18 10:59, Jon Hunter wrote: > Please include the following fix for stable v4.4.y. If the PLL_U is not > configured by the bootloader, then without this change it will not be > configured by the kernel and this will cause USB host support to fail > which uses the PLL_U for its clock. > > Please note that this patch did not apply cleanly to v4.4.y, so I have > back-ported, but the resulting change is the same as the original. > >>From 797097301860c64b63346d068ba4fe4992bd5021 Mon Sep 17 00:00:00 2001 > From: Lucas Stach <dev(a)lynxeye.de> > Date: Mon, 29 Feb 2016 21:46:07 +0100 > Subject: [PATCH] clk: tegra: Fix PLL_U post divider and initial rate on > Tegra30 > > commit 797097301860c64b63346d068ba4fe4992bd5021 upstream > > The post divider value in the frequency table is wrong as it would lead > to the PLL producing an output rate of 960 MHz instead of the desired > 480 MHz. This wasn't a problem as nothing used the table to actually > initialize the PLL rate, but the bootloader configuration was used > unaltered. > > If the bootloader does not set up the PLL it will fail to come when used > under Linux. To fix this don't rely on the bootloader, but set the > correct rate in the clock driver. > > Change-Id: I9375c24ef0d48b1b98be10378e8d593299b0453b > Signed-off-by: Lucas Stach <dev(a)lynxeye.de> > Signed-off-by: Thierry Reding <treding(a)nvidia.com> > [jonathanh(a)nvidia.com: Back-ported to stable v4.4.y] > Signed-off-by: Jon Hunter <jonathanh(a)nvidia.com> > --- > drivers/clk/tegra/clk-tegra30.c | 11 ++++++----- > 1 file changed, 6 insertions(+), 5 deletions(-) > > diff --git a/drivers/clk/tegra/clk-tegra30.c b/drivers/clk/tegra/clk-tegra30.c > index 8c41c6fcb9ee..acf83569f86f 100644 > --- a/drivers/clk/tegra/clk-tegra30.c > +++ b/drivers/clk/tegra/clk-tegra30.c > @@ -333,11 +333,11 @@ static struct pdiv_map pllu_p[] = { > }; > > static struct tegra_clk_pll_freq_table pll_u_freq_table[] = { > - { 12000000, 480000000, 960, 12, 0, 12}, > - { 13000000, 480000000, 960, 13, 0, 12}, > - { 16800000, 480000000, 400, 7, 0, 5}, > - { 19200000, 480000000, 200, 4, 0, 3}, > - { 26000000, 480000000, 960, 26, 0, 12}, > + { 12000000, 480000000, 960, 12, 2, 12 }, > + { 13000000, 480000000, 960, 13, 2, 12 }, > + { 16800000, 480000000, 400, 7, 2, 5 }, > + { 19200000, 480000000, 200, 4, 2, 3 }, > + { 26000000, 480000000, 960, 26, 2, 12 }, > { 0, 0, 0, 0, 0, 0 }, > }; > > @@ -1372,6 +1372,7 @@ static struct tegra_clk_init_table init_table[] __initdata = { > {TEGRA30_CLK_GR2D, TEGRA30_CLK_PLL_C, 300000000, 0}, > {TEGRA30_CLK_GR3D, TEGRA30_CLK_PLL_C, 300000000, 0}, > {TEGRA30_CLK_GR3D2, TEGRA30_CLK_PLL_C, 300000000, 0}, > + { TEGRA30_CLK_PLL_U, TEGRA30_CLK_CLK_MAX, 480000000, 0 }, > {TEGRA30_CLK_CLK_MAX, TEGRA30_CLK_CLK_MAX, 0, 0}, /* This MUST be the last entry. */ > }; > > -- nvpublic

6 years, 12 months

1
0
0 0

by Mukesh Ojha

Adding stable and lkml. Sorry for spam others. -Mukesh On 7/23/2018 1:57 PM, Mukesh Ojha wrote: > > Hi All, > > I wanted to discuss about one of the corner case exists in 4.9 kernel > (4.9.x) where > If hotplug of one of the CPU fails due to failure in one of the callback, > which is to be called after "notify:online"(as notify_online will > create sysfs nodes > for the hotplug cpu) . > > So, while cleaning up notify_dead() does not get called as step > <https://elixir.bootlin.com/linux/v4.9/ident/step>->skip_onerr set to > true for "notify:prepare"and due to that sysfs nodes of that cpu does > not get > cleaned up which can cause issue in next hotplug attempt of that cpu. > > Fails > cpuhp_up_callbacks > <https://elixir.bootlin.com/linux/v4.9/ident/cpuhp_up_callbacks> => > cpuhp_invoke_callback > <https://elixir.bootlin.com/linux/v4.9/ident/cpuhp_invoke_callback> => > undo_cpu_up <https://elixir.bootlin.com/linux/v4.9/ident/undo_cpu_up> > > .name = "notify:prepare", > .teardown.single = notify_dead > <https://elixir.bootlin.com/linux/v4.9/ident/notify_dead>, > .skip_onerr = true, > > I think the possible solution here could be to remove the > - .skip_onerr = true, > > for "notify:prepare"so that CPU_DEAD notification get send. > > Please, feel free to suggest if it has any side-effect as i don't feel > any. > > Ref: > > https://elixir.bootlin.com/linux/v4.9/source/kernel/cpu.c#L458 > > Cheers, > Mukesh > > > > > >

6 years, 12 months

2
1
0 0

request (x86 + stack protector + paravirt + clang)

by Nick Desaulniers

Please cherry-pick upstream commits: d03db2b "compiler-gcc.h: Add __attribute__((gnu_inline)) to all inline declarations" 0e2e160 "x86/asm: Add _ASM_ARG* constants for argument registers to <asm/asm.h>" d0a8d93 "x86/paravirt: Make native_save_fl() extern inline" To stable branches 4.4+. They will allow 4.4+ x86 kernels compiled with Clang and have the configs CONFIG_STACK_PROTECTOR_STRONG and CONFIG_PARAVIRT to boot. They also allow gcc 5.1+ users to have consistent `extern inline` semantics. In response to: https://android-review.googlesource.com/c/kernel/common/+/716477#message-29… One of these days I'll remember to cc stable in the commit message properly...sorry! -- Thanks, ~Nick Desaulniers

6 years, 12 months

3
11
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror