On Thu, Oct 27, 2022 at 09:19:43AM +0900, Dominique Martinet wrote:
From: Lukas Wunner lukas@wunner.de
When a UART port is newly registered, uart_configure_port() seeks to deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl. However a number of UART drivers interpret a set RTS bit as *assertion* instead of deassertion: Affected drivers include those using serial8250_em485_config() (except 8250_bcm2835aux.c) and some using mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not suitable as a means to centrally deassert Transmit Enable in the serial core. Instead, the serial core must call on drivers to deassert it in their driver-specific way. One way to achieve that is to call ->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke uart_rs485_config(). That allows removing calls to uart_rs485_config() from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no hardware flow control, so the modem control lines are irrelevant and need not be touched. When leaving RS485 mode, reset the modem control lines to the state stored in port->mctrl. That way, UARTs which are muxed between RS485 and RS232 transceivers drive the lines correctly when switched to RS232. (serial8250_do_startup() historically raises the OUT1 modem signal because otherwise interrupts are not signaled on ancient PC UARTs, but I believe that no longer applies to modern, RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and deasserted. Stop it from doing that so port->mctrl reflects the RS232 line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling ->set_mctrl(). Because that is now a no-op in RS485 mode, amend the function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties after registering the UART port. Because applying now happens on registration in uart_configure_port(), move retrieval of the properties ahead of uart_add_one_port().
[ Upstream commit 7c7f9bc986e698873b489c371a08f206979d06b7 ] Link: https://lkml.kernel.org/r/20221017051737.51727-2-dominique.martinet@atmark-t... Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-... Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@g... Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Matthias Schiffer matthias.schiffer@ew.tq-group.com Reported-by: Roosen Henri Henri.Roosen@ginzinger.com Tested-by: Matthias Schiffer matthias.schiffer@ew.tq-group.com Reviewed-by: Ilpo Järvinen ilpo.jarvinen@linux.intel.com Signed-off-by: Lukas Wunner lukas@wunner.de Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.166386380... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Daisuke Mizobuchi mizo@atmark-techno.com Signed-off-by: Dominique Martinet dominique.martinet@atmark-techno.com
5.15 version of the 5.10 patch: https://lkml.kernel.org/r/20221017051737.51727-2-dominique.martinet@atmark-t... (only build tested)
Both now queued up, thanks.
greg k-h