The patch below does not apply to the 5.10-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to stable@vger.kernel.org.
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From cf9d052aa6005f1e8dfaf491d83bf37f368af69e Mon Sep 17 00:00:00 2001
From: Douglas Anderson dianders@chromium.org Date: Thu, 14 Jan 2021 19:16:24 -0800 Subject: [PATCH] pinctrl: qcom: Don't clear pending interrupts when enabling
In Linux, if a driver does disable_irq() and later does enable_irq() on its interrupt, I believe it's expecting these properties: * If an interrupt was pending when the driver disabled then it will still be pending after the driver re-enables. * If an edge-triggered interrupt comes in while an interrupt is disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and enable_irq() are supposed to be masking/unmasking the interrupt instead of disabling/enabling it then you've made an astute observation. Specifically when talking about interrupts, "mask" usually means to stop posting interrupts but keep tracking them and "disable" means to fully shut off interrupt detection. It's unfortunate that this is so confusing, but presumably this is all the way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of IRQs themselves don't have a way to request mask/unmask vs. disable/enable calls, IRQ chips themselves can implement both. ...and yet more confusing is that if an IRQ chip implements disable/enable then they will be called when a client driver calls disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However, without any other core interrupt changes it should be clear that when an IRQ chip gets a request to "disable" an IRQ that it has to treat it like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask and clear" can break things. Maulik tried to fix it so that we no longer did "unmask and clear" in commit 71266d9d3936 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback"), but it only handled the PDC case and it had problems (it caused sc7180-trogdor devices to fail to suspend). Let's fix.
From my understanding the source of the phantom interrupt in the
were these two things: 1. One that could have been introduced in msm_gpio_irq_set_type() (only for the non-PDC case). 2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states, sleep and default, and mux between the two during runtime PM and system suspend (see geni_se_resources_{on,off}() for more details). The difference between the sleep and default state is that the RX pin is muxed to a GPIO during sleep and muxed to the UART otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC (or the non-PDC interrupt detection logic) is still watching it / latching edges. These edges don't cause interrupts because the current code masks the interrupt unless we're entering suspend. However, as soon as we enter suspend we unmask the interrupt and it's counted as a wakeup.
Let's deal with the problem like this: * When we mux away, we'll mask our interrupt. This isn't necessary in the above case since the client already masked us, but it's a good idea in general. * When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for msm gpio") Fixes: 71266d9d3936 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback") Signed-off-by: Douglas Anderson dianders@chromium.org Reviewed-by: Maulik Shah mkshah@codeaurora.org Tested-by: Maulik Shah mkshah@codeaurora.org Reviewed-by: Stephen Boyd swboyd@chromium.org Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b6... Signed-off-by: Linus Walleij linus.walleij@linaro.org
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c index 192ed31eabf4..d70caecd21d2 100644 --- a/drivers/pinctrl/qcom/pinctrl-msm.c +++ b/drivers/pinctrl/qcom/pinctrl-msm.c @@ -51,6 +51,7 @@ * @dual_edge_irqs: Bitmap of irqs that need sw emulated dual edge * detection. * @skip_wake_irqs: Skip IRQs that are handled by wakeup interrupt controller + * @disabled_for_mux: These IRQs were disabled because we muxed away. * @soc: Reference to soc_data of platform specific data. * @regs: Base addresses for the TLMM tiles. * @phys_base: Physical base address @@ -72,6 +73,7 @@ struct msm_pinctrl { DECLARE_BITMAP(dual_edge_irqs, MAX_NR_GPIO); DECLARE_BITMAP(enabled_irqs, MAX_NR_GPIO); DECLARE_BITMAP(skip_wake_irqs, MAX_NR_GPIO); + DECLARE_BITMAP(disabled_for_mux, MAX_NR_GPIO);
const struct msm_pinctrl_soc_data *soc; void __iomem *regs[MAX_NR_TILES]; @@ -179,6 +181,10 @@ static int msm_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned group) { struct msm_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); + struct gpio_chip *gc = &pctrl->chip; + unsigned int irq = irq_find_mapping(gc->irq.domain, group); + struct irq_data *d = irq_get_irq_data(irq); + unsigned int gpio_func = pctrl->soc->gpio_func; const struct msm_pingroup *g; unsigned long flags; u32 val, mask; @@ -195,6 +201,20 @@ static int msm_pinmux_set_mux(struct pinctrl_dev *pctldev, if (WARN_ON(i == g->nfuncs)) return -EINVAL;
+ /* + * If an GPIO interrupt is setup on this pin then we need special + * handling. Specifically interrupt detection logic will still see + * the pin twiddle even when we're muxed away. + * + * When we see a pin with an interrupt setup on it then we'll disable + * (mask) interrupts on it when we mux away until we mux back. Note + * that disable_irq() refcounts and interrupts are disabled as long as + * at least one disable_irq() has been called. + */ + if (d && i != gpio_func && + !test_and_set_bit(d->hwirq, pctrl->disabled_for_mux)) + disable_irq(irq); + raw_spin_lock_irqsave(&pctrl->lock, flags);
val = msm_readl_ctl(pctrl, g); @@ -204,6 +224,20 @@ static int msm_pinmux_set_mux(struct pinctrl_dev *pctldev,
raw_spin_unlock_irqrestore(&pctrl->lock, flags);
+ if (d && i == gpio_func && + test_and_clear_bit(d->hwirq, pctrl->disabled_for_mux)) { + /* + * Clear interrupts detected while not GPIO since we only + * masked things. + */ + if (d->parent_data && test_bit(d->hwirq, pctrl->skip_wake_irqs)) + irq_chip_set_parent_state(d, IRQCHIP_STATE_PENDING, false); + else + msm_ack_intr_status(pctrl, g); + + enable_irq(irq); + } + return 0; }
@@ -781,7 +815,7 @@ static void msm_gpio_irq_mask(struct irq_data *d) raw_spin_unlock_irqrestore(&pctrl->lock, flags); }
-static void msm_gpio_irq_clear_unmask(struct irq_data *d, bool status_clear) +static void msm_gpio_irq_unmask(struct irq_data *d) { struct gpio_chip *gc = irq_data_get_irq_chip_data(d); struct msm_pinctrl *pctrl = gpiochip_get_data(gc); @@ -799,14 +833,6 @@ static void msm_gpio_irq_clear_unmask(struct irq_data *d, bool status_clear)
raw_spin_lock_irqsave(&pctrl->lock, flags);
- /* - * clear the interrupt status bit before unmask to avoid - * any erroneous interrupts that would have got latched - * when the interrupt is not in use. - */ - if (status_clear) - msm_ack_intr_status(pctrl, g); - val = msm_readl_intr_cfg(pctrl, g); val |= BIT(g->intr_raw_status_bit); val |= BIT(g->intr_enable_bit); @@ -826,7 +852,7 @@ static void msm_gpio_irq_enable(struct irq_data *d) irq_chip_enable_parent(d);
if (!test_bit(d->hwirq, pctrl->skip_wake_irqs)) - msm_gpio_irq_clear_unmask(d, true); + msm_gpio_irq_unmask(d); }
static void msm_gpio_irq_disable(struct irq_data *d) @@ -841,11 +867,6 @@ static void msm_gpio_irq_disable(struct irq_data *d) msm_gpio_irq_mask(d); }
-static void msm_gpio_irq_unmask(struct irq_data *d) -{ - msm_gpio_irq_clear_unmask(d, false); -} - /** * msm_gpio_update_dual_edge_parent() - Prime next edge for IRQs handled by parent. * @d: The irq dta. @@ -934,6 +955,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type) struct msm_pinctrl *pctrl = gpiochip_get_data(gc); const struct msm_pingroup *g; unsigned long flags; + bool was_enabled; u32 val;
if (msm_gpio_needs_dual_edge_parent_workaround(d, type)) { @@ -995,6 +1017,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type) * could cause the INTR_STATUS to be set for EDGE interrupts. */ val = msm_readl_intr_cfg(pctrl, g); + was_enabled = val & BIT(g->intr_raw_status_bit); val |= BIT(g->intr_raw_status_bit); if (g->intr_detection_width == 2) { val &= ~(3 << g->intr_detection_bit); @@ -1044,6 +1067,14 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type) } msm_writel_intr_cfg(val, pctrl, g);
+ /* + * The first time we set RAW_STATUS_EN it could trigger an interrupt. + * Clear the interrupt. This is safe because we have + * IRQCHIP_SET_TYPE_MASKED. + */ + if (!was_enabled) + msm_ack_intr_status(pctrl, g); + if (test_bit(d->hwirq, pctrl->dual_edge_irqs)) msm_gpio_update_dual_edge_pos(pctrl, g, d);
@@ -1097,16 +1128,11 @@ static int msm_gpio_irq_reqres(struct irq_data *d) }
/* - * Clear the interrupt that may be pending before we enable - * the line. - * This is especially a problem with the GPIOs routed to the - * PDC. These GPIOs are direct-connect interrupts to the GIC. - * Disabling the interrupt line at the PDC does not prevent - * the interrupt from being latched at the GIC. The state at - * GIC needs to be cleared before enabling. + * The disable / clear-enable workaround we do in msm_pinmux_set_mux() + * only works if disable is not lazy since we only clear any bogus + * interrupt in hardware. Explicitly mark the interrupt as UNLAZY. */ - if (d->parent_data && test_bit(d->hwirq, pctrl->skip_wake_irqs)) - irq_chip_set_parent_state(d, IRQCHIP_STATE_PENDING, 0); + irq_set_status_flags(d->irq, IRQ_DISABLE_UNLAZY);
return 0; out: