Commit 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"") removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices, instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c.
This was done because the DIY BTUSB_RESET_RESUME reset-resume handling has several issues (see the original commit message). An added advantage of moving over to the USB-core reset-resume handling is that it also disables autosuspend for these devices, which is similarly broken on these.
But there are 2 issues with this approach: 1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek devices. 2) Sofar only 2 of the 10 QCA devices known to the btusb code have been added to usb/core/quirks.c and if we fix the Realtek case the same way we need to add an additional 14 entries. So in essence we need to duplicate a large part of the usb_device_id table in btusb.c in usb/core/quirks.c and manually keep them in sync.
This commit instead restores setting a reset-resume quirk for QCA devices in the btusb.c code, avoiding the duplicate usb_device_id table problem.
This commit avoids the problems with the original DIY BTUSB_RESET_RESUME code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the usb_device.
This commit also moves the BTUSB_REALTEK case over to directly setting the USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused BTUSB_RESET_RESUME code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"") Cc: stable@vger.kernel.org Cc: Leif Liddy leif.linux@gmail.com Cc: Matthias Kaehlcke mka@chromium.org Cc: Brian Norris briannorris@chromium.org Cc: Daniel Drake drake@endlessm.com Cc: Kai-Heng Feng kai.heng.feng@canonical.com Signed-off-by: Hans de Goede hdegoede@redhat.com --- Note: 1) Once this has been merged, the 2 commits adding QCA device entries to drivers/usb/core/quirks.c should be reverted or dropped from bluetooth-next. 2) I don't have any of the affected devices, please test --- drivers/bluetooth/btusb.c | 22 ++++++++++------------ 1 file changed, 10 insertions(+), 12 deletions(-)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 4764100a5888..c4689f03220f 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -23,6 +23,7 @@
#include <linux/module.h> #include <linux/usb.h> +#include <linux/usb/quirks.h> #include <linux/firmware.h> #include <linux/of_device.h> #include <linux/of_irq.h> @@ -388,9 +389,8 @@ static const struct usb_device_id blacklist_table[] = { #define BTUSB_FIRMWARE_LOADED 7 #define BTUSB_FIRMWARE_FAILED 8 #define BTUSB_BOOTING 9 -#define BTUSB_RESET_RESUME 10 -#define BTUSB_DIAG_RUNNING 11 -#define BTUSB_OOB_WAKE_ENABLED 12 +#define BTUSB_DIAG_RUNNING 10 +#define BTUSB_OOB_WAKE_ENABLED 11
struct btusb_data { struct hci_dev *hdev; @@ -3118,6 +3118,12 @@ static int btusb_probe(struct usb_interface *intf, if (id->driver_info & BTUSB_QCA_ROME) { data->setup_on_usb = btusb_setup_qca; hdev->set_bdaddr = btusb_set_bdaddr_ath3012; + + /* QCA Rome devices lose their updated firmware over suspend, + * but the USB hub doesn't notice any status change. + * explicitly request a device reset on resume. + */ + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; }
#ifdef CONFIG_BT_HCIBTUSB_RTL @@ -3128,7 +3134,7 @@ static int btusb_probe(struct usb_interface *intf, * but the USB hub doesn't notice any status change. * Explicitly request a device reset on resume. */ - set_bit(BTUSB_RESET_RESUME, &data->flags); + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #endif
@@ -3297,14 +3303,6 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message) enable_irq(data->oob_wake_irq); }
- /* Optionally request a device reset on resume, but only when - * wakeups are disabled. If wakeups are enabled we assume the - * device will stay powered up throughout suspend. - */ - if (test_bit(BTUSB_RESET_RESUME, &data->flags) && - !device_may_wakeup(&data->udev->dev)) - data->udev->reset_resume = 1; - return 0; }