This is a note to let you know that I've just added the patch titled
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
to the 4.14-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git%3Ba=su...
The filename of the patch is: arm64-dts-renesas-ulcb-remove-renesas-no-ether-link-property.patch and it can be found in the queue-4.14 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree, please let stable@vger.kernel.org know about it.
From foo@baz Wed Feb 28 16:23:28 CET 2018
From: Bogdan Mirea Bogdan-Stefan_Mirea@mentor.com Date: Thu, 21 Dec 2017 17:18:59 +0200 Subject: arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
From: Bogdan Mirea Bogdan-Stefan_Mirea@mentor.com
[ Upstream commit 7d2901f809c110bd9a261e879d59efe62e3bc758 ]
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce: - start AVB TX stream (Using aplay via MSE), - disconnect+reconnect the eth cable, - after a reconnection the eth connection goes iteratively up/down without user interaction, - this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option should be used when a board does not provide a proper AVB_LINK signal. There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will have impact on the code flow in the following ways: - keeping this option enabled may lead to unexpected behavior since the RX & TX are enabled/disabled directly from adjust_link function without any HW interrogation, - removing this option, the RX & TX will only be enabled/disabled after HW interrogation. The HW check is made through the LMON pin in PSR register which specifies AVB_LINK signal value (0 - at low level; 1 - at high level).
In conclusion, the present change is also a safety improvement because it removes the "renesas,no-ether-link" option leading to a proper way of detecting the link state based on HW interrogation and not on software heuristic.
Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB") Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X") Signed-off-by: Bogdan Mirea Bogdan-Stefan_Mirea@mentor.com Signed-off-by: Vladimir Zapolskiy vladimir_zapolskiy@mentor.com Signed-off-by: Simon Horman horms+renesas@verge.net.au Signed-off-by: Sasha Levin alexander.levin@verizon.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/arm64/boot/dts/renesas/ulcb.dtsi | 1 - 1 file changed, 1 deletion(-)
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi @@ -145,7 +145,6 @@ &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; - renesas,no-ether-link; phy-handle = <&phy0>; status = "okay";
Patches currently in stable-queue which might be from Bogdan-Stefan_Mirea@mentor.com are
queue-4.14/arm64-dts-renesas-ulcb-remove-renesas-no-ether-link-property.patch