On Mon, Jul 14, 2025 at 10:44:13AM +0300, Josua Mayer wrote:
This reverts commit 8a1365c7bbc122bd843096f0008d259e7a8afc61.
The commit in questions most notably breaks SD-Card on SolidRun LX2162A Clearfog by corrupting the pinmux in dynamic configuration area for non-i2c pins without pinmux node. It is further expected that it breaks SD Card-Detect, as well as CAN, DSPI and GPIOs on any board based on LX2160 SoC.
Thank you for your patch. I remember we met similar issue before. Let's wait for carlos is back about in next week.
I remember uboot should copy RCWSR to 0x70010012c. I2C recover also is important feature.
Frank
Background:
The LX2160 SoC is configured at power-on from RCW (Reset Configuration Word) typically located in the first 4k of boot media. This blob configures various clock rates and pin functions. The pinmux for i2c specifically is part of configuration words RCWSR12, RCWSR13 and RCWSR14 size 32 bit each. These values are accessible at read-only addresses 0x01e0012c following.
For runtime (re-)configuration the SoC has a dynamic configuration area where alternative settings can be applied. The counterparts of RCWSR[12-14] can be overridden at 0x70010012c following.
The commit in question used this area to switch i2c pins between i2c and gpio function at runtime using the pinctrl-single driver - which reads a 32-bit value, makes particular changes by bitmask and writes back the new value.
SolidRun have observed that if the dynamic configuration is read first (before a write), it reads as zero regardless the initial values set by RCW. After the first write consecutive reads reflect the written value.
Because multiple pins are configured from a single 32-bit value, this causes unintentional change of all bits (except those for i2c) being set to zero when the pinctrl driver applies the first configuration.
See below a short list of which functions RCWSR12 alone controls:
LX2162-CF RCWSR12: 0b0000100000000000 0000000000000110 IIC2_PMUX ||| ||| || | ||| |||XXX : I2C/GPIO/CD-WP IIC3_PMUX ||| ||| || | ||| XXX : I2C/GPIO/CAN/EVT IIC4_PMUX ||| ||| || | |||XXX||| : I2C/GPIO/CAN/EVT IIC5_PMUX ||| ||| || | XXX ||| : I2C/GPIO/SDHC-CLK IIC6_PMUX ||| ||| || |XXX||| ||| : I2C/GPIO/SDHC-CLK XSPI1_A_DATA74_PMUX ||| ||| XX X ||| ||| : XSPI/GPIO XSPI1_A_DATA30_PMUX ||| |||XXX|| | ||| ||| : XSPI/GPIO XSPI1_A_BASE_PMUX ||| XXX || | ||| ||| : XSPI/GPIO SDHC1_BASE_PMUX |||XXX||| || | ||| ||| : SDHC/GPIO/SPI SDHC1_DIR_PMUX XXX ||| || | ||| ||| : SDHC/GPIO/SPI RESERVED XX||| ||| || | ||| ||| :
On LX2162A Clearfog the initial (ant intended) value is 0x08000006 - enabling card-detect on IIC2_PMUX and some LEDs on SDHC1_DIR_PMUX. Everything else is intentional zero (enabling I2C & XSPI).
By reading zero from dynamic configuration area, the commit in question changes IIC2_PMUX to value 0 (I2C function), and SDHC1_DIR_PMUX to 0 (SDHC data direction function) - breaking card-detect and led gpios.
This issue should affect any board based on LX2160 SoC that is using the same or earlier versions of NXP bootloader as SolidRun have tested, in particular: LSDK-21.08 and LS-5.15.71-2.2.0.
Whether NXP added some extra initialisation in the bootloader on later releases was not investigated. However bootloader upgrade should not be necessary to run a newer Linux kernel.
To work around this issue it is possible to explicitly define ALL pins controlled by any 32-bit value so that gradually after processing all pinctrl nodes the correct value is reached on all bits.
This is a large task that should be done carefully on a per-board basis and not globally through the SoC dtsi. Therefore the commit in question is reverted.
Fixes: 8a1365c7bbc1 ("arm64: dts: lx2160a: add pinmux and i2c gpio to support bus recovery") Cc: stable@vger.kernel.org Signed-off-by: Josua Mayer josua@solid-run.com
Changes in v2:
- changed to revert problematic commit, workaround is large effort
- Link to v1: https://lore.kernel.org/r/f32c5525-3162-4acd-880c-99fc46d3a63d@solid-run.com
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 106 ------------------------- 1 file changed, 106 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index c9541403bcd8..eb1b4e607e2b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -749,10 +749,6 @@ i2c0: i2c@2000000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c0_scl>;pinctrl-1 = <&i2c0_scl_gpio>;scl-gpios = <&gpio0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -765,10 +761,6 @@ i2c1: i2c@2010000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c1_scl>;pinctrl-1 = <&i2c1_scl_gpio>;scl-gpios = <&gpio0 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -781,10 +773,6 @@ i2c2: i2c@2020000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c2_scl>;pinctrl-1 = <&i2c2_scl_gpio>;scl-gpios = <&gpio0 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -797,10 +785,6 @@ i2c3: i2c@2030000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c3_scl>;pinctrl-1 = <&i2c3_scl_gpio>;scl-gpios = <&gpio0 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -813,10 +797,6 @@ i2c4: i2c@2040000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c4_scl>;pinctrl-1 = <&i2c4_scl_gpio>;scl-gpios = <&gpio0 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -829,10 +809,6 @@ i2c5: i2c@2050000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c5_scl>;pinctrl-1 = <&i2c5_scl_gpio>;scl-gpios = <&gpio0 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -845,10 +821,6 @@ i2c6: i2c@2060000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c6_scl>;pinctrl-1 = <&i2c6_scl_gpio>;scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -861,10 +833,6 @@ i2c7: i2c@2070000 { clock-names = "ipg"; clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(16)>;
pinctrl-names = "default", "gpio";pinctrl-0 = <&i2c7_scl>;pinctrl-1 = <&i2c7_scl_gpio>;scl-gpios = <&gpio1 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "disabled";@@ -1700,80 +1668,6 @@ pcs18: ethernet-phy@0 { }; };
pinmux_i2crv: pinmux@70010012c {compatible = "pinctrl-single";reg = <0x00000007 0x0010012c 0x0 0xc>;#address-cells = <1>;#size-cells = <0>;pinctrl-single,bit-per-mux;pinctrl-single,register-width = <32>;pinctrl-single,function-mask = <0x7>;i2c1_scl: i2c1-scl-pins {pinctrl-single,bits = <0x0 0 0x7>;};i2c1_scl_gpio: i2c1-scl-gpio-pins {pinctrl-single,bits = <0x0 0x1 0x7>;};i2c2_scl: i2c2-scl-pins {pinctrl-single,bits = <0x0 0 (0x7 << 3)>;};i2c2_scl_gpio: i2c2-scl-gpio-pins {pinctrl-single,bits = <0x0 (0x1 << 3) (0x7 << 3)>;};i2c3_scl: i2c3-scl-pins {pinctrl-single,bits = <0x0 0 (0x7 << 6)>;};i2c3_scl_gpio: i2c3-scl-gpio-pins {pinctrl-single,bits = <0x0 (0x1 << 6) (0x7 << 6)>;};i2c4_scl: i2c4-scl-pins {pinctrl-single,bits = <0x0 0 (0x7 << 9)>;};i2c4_scl_gpio: i2c4-scl-gpio-pins {pinctrl-single,bits = <0x0 (0x1 << 9) (0x7 << 9)>;};i2c5_scl: i2c5-scl-pins {pinctrl-single,bits = <0x0 0 (0x7 << 12)>;};i2c5_scl_gpio: i2c5-scl-gpio-pins {pinctrl-single,bits = <0x0 (0x1 << 12) (0x7 << 12)>;};i2c6_scl: i2c6-scl-pins {pinctrl-single,bits = <0x4 0x2 0x7>;};i2c6_scl_gpio: i2c6-scl-gpio-pins {pinctrl-single,bits = <0x4 0x1 0x7>;};i2c7_scl: i2c7-scl-pins {pinctrl-single,bits = <0x4 0x2 0x7>;};i2c7_scl_gpio: i2c7-scl-gpio-pins {pinctrl-single,bits = <0x4 0x1 0x7>;};i2c0_scl: i2c0-scl-pins {pinctrl-single,bits = <0x8 0 (0x7 << 10)>;};i2c0_scl_gpio: i2c0-scl-gpio-pins {pinctrl-single,bits = <0x8 (0x1 << 10) (0x7 << 10)>;};};- fsl_mc: fsl-mc@80c000000 { compatible = "fsl,qoriq-mc"; reg = <0x00000008 0x0c000000 0 0x40>,
base-commit: 19272b37aa4f83ca52bdf9c16d5d81bdd1354494 change-id: 20250710-lx2160-sd-cd-00bf38ae169e
Best regards,
Josua Mayer josua@solid-run.com