Fix broken config in qcom_param_page_type_exec caused by copy-paste error from commit 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
In qcom_param_page_type_exec the value needs to be set to nandc->regs->cfg0 instead of host->cfg0. This wrong configuration caused the Qcom NANDC driver to malfunction on any device that makes use of it (IPQ806x, IPQ40xx, IPQ807x, IPQ60xx) with the following error:
[ 0.885369] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa [ 0.885909] nand: Micron NAND 256MiB 1,8V 8-bit [ 0.892499] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.896823] nand: ECC (step, strength) = (512, 8) does not fit in OOB [ 0.896836] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible [ 0.910996] bam-dma-engine 7984000.dma-controller: Cannot free busy channel [ 0.918070] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Restore original configuration fix the problem and makes the driver work again.
Also restore the wrongly dropped cpu_to_le32 to correctly support BE systems.
Cc: stable@vger.kernel.org Fixes: 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK") Tested-by: Robert Marko robimarko@gmail.com # IPQ8074 and IPQ6018 Signed-off-by: Christian Marangi ansuelsmth@gmail.com --- Changes v2: - Fix smatch warning (add missing cpu_to_le32 that was also dropped from the FIELD_PREP patch)
drivers/mtd/nand/raw/qcom_nandc.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c index d2d2aeee42a7..6720b547892b 100644 --- a/drivers/mtd/nand/raw/qcom_nandc.c +++ b/drivers/mtd/nand/raw/qcom_nandc.c @@ -1881,18 +1881,18 @@ static int qcom_param_page_type_exec(struct nand_chip *chip, const struct nand_ nandc->regs->addr0 = 0; nandc->regs->addr1 = 0;
- host->cfg0 = FIELD_PREP(CW_PER_PAGE_MASK, 0) | - FIELD_PREP(UD_SIZE_BYTES_MASK, 512) | - FIELD_PREP(NUM_ADDR_CYCLES_MASK, 5) | - FIELD_PREP(SPARE_SIZE_BYTES_MASK, 0); - - host->cfg1 = FIELD_PREP(NAND_RECOVERY_CYCLES_MASK, 7) | - FIELD_PREP(BAD_BLOCK_BYTE_NUM_MASK, 17) | - FIELD_PREP(CS_ACTIVE_BSY, 0) | - FIELD_PREP(BAD_BLOCK_IN_SPARE_AREA, 1) | - FIELD_PREP(WR_RD_BSY_GAP_MASK, 2) | - FIELD_PREP(WIDE_FLASH, 0) | - FIELD_PREP(DEV0_CFG1_ECC_DISABLE, 1); + nandc->regs->cfg0 = cpu_to_le32(FIELD_PREP(CW_PER_PAGE_MASK, 0) | + FIELD_PREP(UD_SIZE_BYTES_MASK, 512) | + FIELD_PREP(NUM_ADDR_CYCLES_MASK, 5) | + FIELD_PREP(SPARE_SIZE_BYTES_MASK, 0)); + + nandc->regs->cfg1 = cpu_to_le32(FIELD_PREP(NAND_RECOVERY_CYCLES_MASK, 7) | + FIELD_PREP(BAD_BLOCK_BYTE_NUM_MASK, 17) | + FIELD_PREP(CS_ACTIVE_BSY, 0) | + FIELD_PREP(BAD_BLOCK_IN_SPARE_AREA, 1) | + FIELD_PREP(WR_RD_BSY_GAP_MASK, 2) | + FIELD_PREP(WIDE_FLASH, 0) | + FIELD_PREP(DEV0_CFG1_ECC_DISABLE, 1));
if (!nandc->props->qpic_version2) nandc->regs->ecc_buf_cfg = cpu_to_le32(ECC_CFG_ECC_DISABLE);