From: Geert Uytterhoeven geert+renesas@glider.be
commit 77972b55fb9d35d4a6b0abca99abffaa4ec6a85b upstream.
This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.
This commit moved the ravb_mdio_init() call (and thus the of_mdiobus_register() call) from the ravb_probe() to the ravb_open() call. This causes a regression during system resume (s2idle/s2ram), as new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228) ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B) usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add() merely adds the device, but does not probe it yet, as really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8 device_resume+0xcc/0x1b0 dpm_run_callback+0x74/0x340 ravb_resume+0x190/0x1b8 ravb_open+0x84/0x770 of_mdiobus_register+0x1e0/0x468 of_mdiobus_register_phy+0x1b8/0x250 of_mdiobus_phy_device_register+0x178/0x1e8 phy_device_register+0x114/0x1b8 device_add+0x3d4/0x798 bus_probe_device+0x98/0xa0 device_initial_probe+0x10/0x18 __device_attach+0xe4/0x140 bus_for_each_drv+0x64/0xc8 __device_attach_driver+0xb8/0xe0 driver_probe_device.part.11+0xc4/0xd8 really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound, and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL) ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622 ravb e6800000.ethernet eth0: failed to initialize MDIO PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16 PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for -ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading PHY driver w/o initramfs"), would makes it fall back to the Generic PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven geert+renesas@glider.be Cc: stable@vger.kernel.org Reviewed-by: Sergei Shtylyov sergei.shtylyov@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
--- drivers/net/ethernet/renesas/ravb_main.c | 110 +++++++++++++++---------------- 1 file changed, 55 insertions(+), 55 deletions(-)
--- a/drivers/net/ethernet/renesas/ravb_main.c +++ b/drivers/net/ethernet/renesas/ravb_main.c @@ -1214,64 +1214,12 @@ static const struct ethtool_ops ravb_eth .get_ts_info = ravb_get_ts_info, };
-/* MDIO bus init function */ -static int ravb_mdio_init(struct ravb_private *priv) -{ - struct platform_device *pdev = priv->pdev; - struct device *dev = &pdev->dev; - int error; - - /* Bitbang init */ - priv->mdiobb.ops = &bb_ops; - - /* MII controller setting */ - priv->mii_bus = alloc_mdio_bitbang(&priv->mdiobb); - if (!priv->mii_bus) - return -ENOMEM; - - /* Hook up MII support for ethtool */ - priv->mii_bus->name = "ravb_mii"; - priv->mii_bus->parent = dev; - snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", - pdev->name, pdev->id); - - /* Register MDIO bus */ - error = of_mdiobus_register(priv->mii_bus, dev->of_node); - if (error) - goto out_free_bus; - - return 0; - -out_free_bus: - free_mdio_bitbang(priv->mii_bus); - return error; -} - -/* MDIO bus release function */ -static int ravb_mdio_release(struct ravb_private *priv) -{ - /* Unregister mdio bus */ - mdiobus_unregister(priv->mii_bus); - - /* Free bitbang info */ - free_mdio_bitbang(priv->mii_bus); - - return 0; -} - /* Network device open function for Ethernet AVB */ static int ravb_open(struct net_device *ndev) { struct ravb_private *priv = netdev_priv(ndev); int error;
- /* MDIO bus init */ - error = ravb_mdio_init(priv); - if (error) { - netdev_err(ndev, "failed to initialize MDIO\n"); - return error; - } - napi_enable(&priv->napi[RAVB_BE]); napi_enable(&priv->napi[RAVB_NC]);
@@ -1320,7 +1268,6 @@ out_free_irq: out_napi_off: napi_disable(&priv->napi[RAVB_NC]); napi_disable(&priv->napi[RAVB_BE]); - ravb_mdio_release(priv); return error; }
@@ -1614,8 +1561,6 @@ static int ravb_close(struct net_device ravb_ring_free(ndev, RAVB_BE); ravb_ring_free(ndev, RAVB_NC);
- ravb_mdio_release(priv); - return 0; }
@@ -1719,6 +1664,51 @@ static const struct net_device_ops ravb_ .ndo_change_mtu = eth_change_mtu, };
+/* MDIO bus init function */ +static int ravb_mdio_init(struct ravb_private *priv) +{ + struct platform_device *pdev = priv->pdev; + struct device *dev = &pdev->dev; + int error; + + /* Bitbang init */ + priv->mdiobb.ops = &bb_ops; + + /* MII controller setting */ + priv->mii_bus = alloc_mdio_bitbang(&priv->mdiobb); + if (!priv->mii_bus) + return -ENOMEM; + + /* Hook up MII support for ethtool */ + priv->mii_bus->name = "ravb_mii"; + priv->mii_bus->parent = dev; + snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", + pdev->name, pdev->id); + + /* Register MDIO bus */ + error = of_mdiobus_register(priv->mii_bus, dev->of_node); + if (error) + goto out_free_bus; + + return 0; + +out_free_bus: + free_mdio_bitbang(priv->mii_bus); + return error; +} + +/* MDIO bus release function */ +static int ravb_mdio_release(struct ravb_private *priv) +{ + /* Unregister mdio bus */ + mdiobus_unregister(priv->mii_bus); + + /* Free bitbang info */ + free_mdio_bitbang(priv->mii_bus); + + return 0; +} + static const struct of_device_id ravb_match_table[] = { { .compatible = "renesas,etheravb-r8a7790", .data = (void *)RCAR_GEN2 }, { .compatible = "renesas,etheravb-r8a7794", .data = (void *)RCAR_GEN2 }, @@ -1857,6 +1847,13 @@ static int ravb_probe(struct platform_de eth_hw_addr_random(ndev); }
+ /* MDIO bus init */ + error = ravb_mdio_init(priv); + if (error) { + dev_err(&pdev->dev, "failed to initialize MDIO\n"); + goto out_dma_free; + } + netif_napi_add(ndev, &priv->napi[RAVB_BE], ravb_poll, 64); netif_napi_add(ndev, &priv->napi[RAVB_NC], ravb_poll, 64);
@@ -1876,6 +1873,8 @@ static int ravb_probe(struct platform_de out_napi_del: netif_napi_del(&priv->napi[RAVB_NC]); netif_napi_del(&priv->napi[RAVB_BE]); + ravb_mdio_release(priv); +out_dma_free: dma_free_coherent(ndev->dev.parent, priv->desc_bat_size, priv->desc_bat, priv->desc_bat_dma); out_release: @@ -1900,6 +1899,7 @@ static int ravb_remove(struct platform_d unregister_netdev(ndev); netif_napi_del(&priv->napi[RAVB_NC]); netif_napi_del(&priv->napi[RAVB_BE]); + ravb_mdio_release(priv); pm_runtime_disable(&pdev->dev); free_netdev(ndev); platform_set_drvdata(pdev, NULL);