From: Ioana Ciornei ioana.ciornei@nxp.com
[ Upstream commit ca2dccdeeb49a7e408112d681bf447984c845292 ]
The Aquantia datasheet notes that after issuing a Processor-Intensive MDIO operation, like changing the low-power state of the device, the driver should wait for the operation to finish before issuing a new MDIO command.
The new aqr107_wait_processor_intensive_op() function is added which can be used after these kind of MDIO operations. At the moment, we are only adding it at the end of the suspend/resume calls.
The issue was identified on a board featuring the AQR113C PHY, on which commands like 'ip link (..) up / down' issued without any delays between them would render the link on the PHY to remain down. The issue was easy to reproduce with a one-liner: $ ip link set dev ethX down; ip link set dev ethX up; \ ip link set dev ethX down; ip link set dev ethX up;
Fixes: ac9e81c230eb ("net: phy: aquantia: add suspend / resume callbacks for AQR107 family") Signed-off-by: Ioana Ciornei ioana.ciornei@nxp.com Reviewed-by: Andrew Lunn andrew@lunn.ch Link: https://lore.kernel.org/r/20220906130451.1483448-1-ioana.ciornei@nxp.com Signed-off-by: Paolo Abeni pabeni@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/phy/aquantia_main.c | 53 ++++++++++++++++++++++++++++++--- 1 file changed, 49 insertions(+), 4 deletions(-)
diff --git a/drivers/net/phy/aquantia_main.c b/drivers/net/phy/aquantia_main.c index 75a62d1cc737..7045595f8d7d 100644 --- a/drivers/net/phy/aquantia_main.c +++ b/drivers/net/phy/aquantia_main.c @@ -89,6 +89,9 @@ #define VEND1_GLOBAL_FW_ID_MAJOR GENMASK(15, 8) #define VEND1_GLOBAL_FW_ID_MINOR GENMASK(7, 0)
+#define VEND1_GLOBAL_GEN_STAT2 0xc831 +#define VEND1_GLOBAL_GEN_STAT2_OP_IN_PROG BIT(15) + #define VEND1_GLOBAL_RSVD_STAT1 0xc885 #define VEND1_GLOBAL_RSVD_STAT1_FW_BUILD_ID GENMASK(7, 4) #define VEND1_GLOBAL_RSVD_STAT1_PROV_ID GENMASK(3, 0) @@ -123,6 +126,12 @@ #define VEND1_GLOBAL_INT_VEND_MASK_GLOBAL2 BIT(1) #define VEND1_GLOBAL_INT_VEND_MASK_GLOBAL3 BIT(0)
+/* Sleep and timeout for checking if the Processor-Intensive + * MDIO operation is finished + */ +#define AQR107_OP_IN_PROG_SLEEP 1000 +#define AQR107_OP_IN_PROG_TIMEOUT 100000 + struct aqr107_hw_stat { const char *name; int reg; @@ -569,16 +578,52 @@ static void aqr107_link_change_notify(struct phy_device *phydev) phydev_info(phydev, "Aquantia 1000Base-T2 mode active\n"); }
+static int aqr107_wait_processor_intensive_op(struct phy_device *phydev) +{ + int val, err; + + /* The datasheet notes to wait at least 1ms after issuing a + * processor intensive operation before checking. + * We cannot use the 'sleep_before_read' parameter of read_poll_timeout + * because that just determines the maximum time slept, not the minimum. + */ + usleep_range(1000, 5000); + + err = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, + VEND1_GLOBAL_GEN_STAT2, val, + !(val & VEND1_GLOBAL_GEN_STAT2_OP_IN_PROG), + AQR107_OP_IN_PROG_SLEEP, + AQR107_OP_IN_PROG_TIMEOUT, false); + if (err) { + phydev_err(phydev, "timeout: processor-intensive MDIO operation\n"); + return err; + } + + return 0; +} + static int aqr107_suspend(struct phy_device *phydev) { - return phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1, - MDIO_CTRL1_LPOWER); + int err; + + err = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1, + MDIO_CTRL1_LPOWER); + if (err) + return err; + + return aqr107_wait_processor_intensive_op(phydev); }
static int aqr107_resume(struct phy_device *phydev) { - return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1, - MDIO_CTRL1_LPOWER); + int err; + + err = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MDIO_CTRL1, + MDIO_CTRL1_LPOWER); + if (err) + return err; + + return aqr107_wait_processor_intensive_op(phydev); }
static int aqr107_probe(struct phy_device *phydev)