From: Bryan O'Donoghue bryan.odonoghue@linaro.org
[ Upstream commit f47ab3c2f5338828a67e89d5f688d2cef9605245 ]
During the process of debugging a processor derived from the msm8916 which we found the new processor was not starting one of its PLLs.
After tracing the addresses and writes that downstream was doing and comparing to upstream it became obvious that we were writing to a different register location than downstream when trying to configure the PLL.
This error is also present in upstream msm8916.
As an example clk-pll.c::clk_pll_recalc_rate wants to write to pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an example
lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
0x01823010 GCC_BIMC_PLL_USER_CTL 0x01823014 GCC_BIMC_PLL_CONFIG_CTL
This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
This error is likely not apparent since the bootloader will already have initialized these PLLs.
This patch corrects the location of config_reg from PLL_CONFIG_CTL to PLL_USER_CTL for all relevant PLLs on msm8916.
Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov georgi.djakov@linaro.org Cc: Andy Gross agross@kernel.org Cc: Bjorn Andersson bjorn.andersson@linaro.org Cc: Michael Turquette mturquette@baylibre.com Cc: Stephen Boyd sboyd@kernel.org Signed-off-by: Bryan O'Donoghue bryan.odonoghue@linaro.org Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.or... Signed-off-by: Stephen Boyd sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/qcom/gcc-msm8916.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c index ac2b0aa1e8b5..03e0ade7a6f3 100644 --- a/drivers/clk/qcom/gcc-msm8916.c +++ b/drivers/clk/qcom/gcc-msm8916.c @@ -268,7 +268,7 @@ static struct clk_pll gpll0 = { .l_reg = 0x21004, .m_reg = 0x21008, .n_reg = 0x2100c, - .config_reg = 0x21014, + .config_reg = 0x21010, .mode_reg = 0x21000, .status_reg = 0x2101c, .status_bit = 17, @@ -295,7 +295,7 @@ static struct clk_pll gpll1 = { .l_reg = 0x20004, .m_reg = 0x20008, .n_reg = 0x2000c, - .config_reg = 0x20014, + .config_reg = 0x20010, .mode_reg = 0x20000, .status_reg = 0x2001c, .status_bit = 17, @@ -322,7 +322,7 @@ static struct clk_pll gpll2 = { .l_reg = 0x4a004, .m_reg = 0x4a008, .n_reg = 0x4a00c, - .config_reg = 0x4a014, + .config_reg = 0x4a010, .mode_reg = 0x4a000, .status_reg = 0x4a01c, .status_bit = 17, @@ -349,7 +349,7 @@ static struct clk_pll bimc_pll = { .l_reg = 0x23004, .m_reg = 0x23008, .n_reg = 0x2300c, - .config_reg = 0x23014, + .config_reg = 0x23010, .mode_reg = 0x23000, .status_reg = 0x2301c, .status_bit = 17,