6.12-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vladimir Oltean vladimir.oltean@nxp.com
[ Upstream commit 426d487bca38b34f39c483edfc6313a036446b33 ]
Simplest setup to reproduce the issue: connect 2 ports of the LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up $ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \ base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \ sched-entry S 20 300000 sched-entry S 48 200000 \ sched-entry S 20 300000 sched-entry S 83 200000 \ sched-entry S 40 300000 sched-entry S 00 200000 flags 2 $ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m & $ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts synchronizing, then it attempts to do a clock step, and after that, it never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627 ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0 ptp4l[84.170]: timed out while polling for tx timestamp ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it ptp4l[84.172]: port 1 (swp0): send peer delay request failed ptp4l[84.173]: port 1 (swp0): clearing fault immediately ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE ptp4l[85.303]: timed out while polling for tx timestamp ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it ptp4l[84.172]: port 1 (swp0): send peer delay request failed ptp4l[84.173]: port 1 (swp0): clearing fault immediately ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE ptp4l[85.303]: timed out while polling for tx timestamp ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it ptp4l[85.305]: port 1 (swp0): send peer delay response failed ptp4l[85.306]: port 1 (swp0): clearing fault immediately ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0 (...) Statistics: tx_pkts: 30 tx_lost: 11 tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64() or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to read the GCL RAM, after the admin schedule became operational, through the two status registers available for this purpose: QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot) { u32 val, list_length, interval, gate_state; int i, err;
err = read_poll_timeout(ocelot_read, val, !(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING), 10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8); if (err) { dev_err(ocelot->dev, "Failed to wait for TAS config pending bit to clear: %pe\n", ERR_PTR(err)); return; }
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3); list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) { ocelot_rmw(ocelot, QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i), QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M, QSYS_GCL_STATUS_REG_1); interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2); val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1); gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n", i, gate_state, interval); } }
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE performed by vsc9959_qos_port_tas_set(), and after the one done by vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8 mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000 mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000 mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000 mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000 mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000 mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000 mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000 mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8 mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0 mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions. It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE for a port's TAS, the GCL entry RAM is updated anyway, despite what the documentation claims: "Specify the time interval in QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM write with the gate state and the time interval for the entry number specified". We don't touch that register (through vsc9959_tas_gcl_set()) from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my testing can hold a variety of things, including even pieces of the previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this issue, because the newly updated schedule would "behave strangely", but ultimately might still pass traffic to some extent, due to some gate entries still being present in the stale GCL entry RAM. It is easy to miss.
With the particular schedule given at the beginning, the GCL RAM "happens" to be reproducibly rewritten with all zeroes, and this is consistent with what we see: when the time-aware shaper has gate entries with all gates closed, traffic is dropped on TX, no wonder we can't retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time") Reported-by: Richie Pearn richard.pearn@nxp.com Signed-off-by: Vladimir Oltean vladimir.oltean@nxp.com Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/dsa/ocelot/felix_vsc9959.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c index 940f1b71226d6..7b35d24c38d76 100644 --- a/drivers/net/dsa/ocelot/felix_vsc9959.c +++ b/drivers/net/dsa/ocelot/felix_vsc9959.c @@ -1543,7 +1543,7 @@ static void vsc9959_tas_clock_adjust(struct ocelot *ocelot) struct tc_taprio_qopt_offload *taprio; struct ocelot_port *ocelot_port; struct timespec64 base_ts; - int port; + int i, port; u32 val;
mutex_lock(&ocelot->fwd_domain_lock); @@ -1575,6 +1575,9 @@ static void vsc9959_tas_clock_adjust(struct ocelot *ocelot) QSYS_PARAM_CFG_REG_3_BASE_TIME_SEC_MSB_M, QSYS_PARAM_CFG_REG_3);
+ for (i = 0; i < taprio->num_entries; i++) + vsc9959_tas_gcl_set(ocelot, i, &taprio->entries[i]); + ocelot_rmw(ocelot, QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE, QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE, QSYS_TAS_PARAM_CFG_CTRL);