From: Ryan Hsu ryanhsu@qca.qualcomm.com
[ Upstream commit 88407beb1b1462f706a1950a355fd086e1c450b6 ]
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0 ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0 ... ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1 ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so that the uninitialized bss_conf.txpower=0 is assinged to the arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface. So the smallest txpower of all vifs will be the one limit the tx power of the physical device, that causing the low txpower issue on other active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm ath10k_pci mac vdev_id 0 txpower 21 ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0 ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21 ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu ryanhsu@qca.qualcomm.com Signed-off-by: Kalle Valo kvalo@qca.qualcomm.com Signed-off-by: Sasha Levin alexander.levin@verizon.com --- drivers/net/wireless/ath/ath10k/mac.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 30e98afa2e68..d3ac7e0745e2 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -4668,7 +4668,8 @@ static int ath10k_mac_txpower_recalc(struct ath10k *ar) lockdep_assert_held(&ar->conf_mutex);
list_for_each_entry(arvif, &ar->arvifs, list) { - WARN_ON(arvif->txpower < 0); + if (arvif->txpower <= 0) + continue;
if (txpower == -1) txpower = arvif->txpower; @@ -4676,8 +4677,8 @@ static int ath10k_mac_txpower_recalc(struct ath10k *ar) txpower = min(txpower, arvif->txpower); }
- if (WARN_ON(txpower == -1)) - return -EINVAL; + if (txpower == -1) + return 0;
ret = ath10k_mac_txpower_setup(ar, txpower); if (ret) {