On Wed, May 08, 2019 at 12:46:09PM +0200, Maarten Lankhorst wrote:
Op 25-04-2019 om 18:29 schreef Ville Syrjala:
From: Ville Syrjälä ville.syrjala@linux.intel.com
On HSW the pipe A panel fitter lives inside the display power well, and the input MUX for the EDP transcoder needs to be configured appropriately to route the data through the power well as needed. Changing the MUX setting is not allowed while the pipe is active, so we need to force a full modeset whenever we need to change it.
Currently we may end up doing a fastset which won't change the MUX settings, but it will drop the power well reference, and that kills the pipe.
Cc: stable@vger.kernel.org Cc: Hans de Goede hdegoede@redhat.com Cc: Maarten Lankhorst maarten.lankhorst@linux.intel.com Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.") Signed-off-by: Ville Syrjälä ville.syrjala@linux.intel.com
drivers/gpu/drm/i915/intel_display.c | 9 +++++++++ drivers/gpu/drm/i915/intel_pipe_crc.c | 13 ++++++++++--- 2 files changed, 19 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index c67f165b466c..691c9a929164 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -12133,6 +12133,7 @@ intel_pipe_config_compare(struct drm_i915_private *dev_priv, struct intel_crtc_state *pipe_config, bool adjust) {
- struct intel_crtc *crtc = to_intel_crtc(current_config->base.crtc); bool ret = true; bool fixup_inherited = adjust && (current_config->base.mode.private_flags & I915_MODE_FLAG_INHERITED) &&
@@ -12354,6 +12355,14 @@ intel_pipe_config_compare(struct drm_i915_private *dev_priv, PIPE_CONF_CHECK_X(gmch_pfit.pgm_ratios); PIPE_CONF_CHECK_X(gmch_pfit.lvds_border_bits);
- /*
* Changing the EDP transcoder input mux* (A_ONOFF vs. A_ON) requires a full modeset.*/- if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A &&
current_config->cpu_transcoder == TRANSCODER_EDP)PIPE_CONF_CHECK_BOOL(pch_pfit.enabled);I guess it depends if we want to make it a blocker or not..
- if (!adjust) { PIPE_CONF_CHECK_I(pipe_src_w); PIPE_CONF_CHECK_I(pipe_src_h);
diff --git a/drivers/gpu/drm/i915/intel_pipe_crc.c b/drivers/gpu/drm/i915/intel_pipe_crc.c index e94b5b1bc1b7..e7c7be4911c1 100644 --- a/drivers/gpu/drm/i915/intel_pipe_crc.c +++ b/drivers/gpu/drm/i915/intel_pipe_crc.c @@ -311,10 +311,17 @@ intel_crtc_crc_setup_workarounds(struct intel_crtc *crtc, bool enable) pipe_config->base.mode_changed = pipe_config->has_psr; pipe_config->crc_enabled = enable;
- if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A) {
- if (IS_HASWELL(dev_priv) &&
pipe_config->base.active && crtc->pipe == PIPE_A &&pipe_config->cpu_transcoder == TRANSCODER_EDP) {bool old_need_power_well = pipe_config->pch_pfit.enabled ||pipe_config->pch_pfit.force_thru;bool new_need_power_well = pipe_config->pch_pfit.enabled ||enable;- pipe_config->pch_pfit.force_thru = enable;
if (pipe_config->cpu_transcoder == TRANSCODER_EDP &&pipe_config->pch_pfit.enabled != enable)
if (old_need_power_well != new_need_power_well) pipe_config->base.connectors_changed = true;Could we get rid of this logic and set mode_changed instead?
Ah, I see that is done in 2/2, much less surprises then. :)
Yeah, wanted to keep the fix itself minimal for backporting.
In that case, for both:
Reviewed-by: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Thanks. Series pushed.