From: Mario Kleiner mario.kleiner.de@gmail.com
commit 341abd693d10e5f337a51f140ae3e7a1ae0febf6 upstream.
This attempts to fix a bug found with a serial port card which uses an MCS9922 chip, one of the 4 models for which MSI-X interrupts are currently supported. I don't possess such a card, and i'm not experienced with the serial subsystem, so this patch is based on what i think i found as a likely reason for failure, based on walking the user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003) [ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2 [ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003) [ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2 ... [ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd) [ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd) ...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127 Baud_base: 115200, close_delay: 50, divisor: 0 closing_wait: 3000 Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the serial port driver means to share the irq, and this mismatch ends in some failed irq init?
With this setup, data reception works very unreliable, with dropped data, already at a transmission rate of only a 16 Bytes chunk every 1/120th of a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recordi...
Disabling the use of MSI interrupts for the serial port pci card did fix the reliability problems. The user executed the following sequence of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers [ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers [ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2 [ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when using MSI irq's. Note that all i know for sure is that disabling MSI irq's fixed the problem for the user, so this patch could be wrong and is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support") Cc: Ralf Ramsauer ralf.ramsauer@oth-regensburg.de Cc: stable stable@vger.kernel.org Reviewed-by: Andy Shevchenko andy.shevchenko@gmail.com Signed-off-by: Mario Kleiner mario.kleiner.de@gmail.com Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/tty/serial/8250/8250_pci.c | 1 + 1 file changed, 1 insertion(+)
--- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -3929,6 +3929,7 @@ pciserial_init_ports(struct pci_dev *dev if (pci_match_id(pci_use_msi, dev)) { dev_dbg(&dev->dev, "Using MSI(-X) interrupts\n"); pci_set_master(dev); + uart.port.flags &= ~UPF_SHARE_IRQ; rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES); } else { dev_dbg(&dev->dev, "Using legacy interrupts\n");