From: Hans de Goede hdegoede@redhat.com
[ Upstream commit c309a3e8793f7e01c4a4ec7960658380572cb576 ]
When the jack is partially inserted and then removed again it may be removed while the hpdet code is running. In this case the following may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers 2. arizona_jackdet runs and takes info->lock 3. The "HPDET" IRQ triggers 4. arizona_hpdet_irq runs, blocks on info->lock 5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done 6. arizona_jackdet releases info->lock 7. arizona_hpdet_irq now can continue running and: 7.1 Calls arizona_start_mic() (if a mic was detected) 7.2 sets info->hpdet_done
Step 7 is undesirable / a bug: 7.1 causes the device to stay in a high power-state (with MICVDD enabled) 7.2 causes hpdet to not run on the next jack insertion, which in turn causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq runs after the jack has been unplugged.
Signed-off-by: Hans de Goede hdegoede@redhat.com Reviewed-by: Andy Shevchenko andy.shevchenko@gmail.com Acked-by: Charles Keepax ckeepax@opensource.cirrus.com Tested-by: Charles Keepax ckeepax@opensource.cirrus.com Acked-by: Chanwoo Choi cw00.choi@samsung.com Signed-off-by: Lee Jones lee.jones@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/extcon/extcon-arizona.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c index 9327479c719c..c857120c00d9 100644 --- a/drivers/extcon/extcon-arizona.c +++ b/drivers/extcon/extcon-arizona.c @@ -602,7 +602,7 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data) struct arizona *arizona = info->arizona; int id_gpio = arizona->pdata.hpdet_id_gpio; unsigned int report = EXTCON_JACK_HEADPHONE; - int ret, reading; + int ret, reading, state; bool mic = false;
mutex_lock(&info->lock); @@ -615,12 +615,11 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data) }
/* If the cable was removed while measuring ignore the result */ - ret = extcon_get_state(info->edev, EXTCON_MECHANICAL); - if (ret < 0) { - dev_err(arizona->dev, "Failed to check cable state: %d\n", - ret); + state = extcon_get_state(info->edev, EXTCON_MECHANICAL); + if (state < 0) { + dev_err(arizona->dev, "Failed to check cable state: %d\n", state); goto out; - } else if (!ret) { + } else if (!state) { dev_dbg(arizona->dev, "Ignoring HPDET for removed cable\n"); goto done; } @@ -673,7 +672,7 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data) ARIZONA_ACCDET_MODE_MASK, ARIZONA_ACCDET_MODE_MIC);
/* If we have a mic then reenable MICDET */ - if (mic || info->mic) + if (state && (mic || info->mic)) arizona_start_mic(info);
if (info->hpdet_active) { @@ -681,7 +680,9 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data) info->hpdet_active = false; }
- info->hpdet_done = true; + /* Do not set hp_det done when the cable has been unplugged */ + if (state) + info->hpdet_done = true;
out: mutex_unlock(&info->lock);