From: Tan Tee Min tee.min.tan@linux.intel.com
commit c76acfb7e19dcc3a0964e0563770b1d11b8d4540 upstream.
There is a limitation in TI DP83867 PHY device where SGMII AN is only triggered once after the device is booted up. Even after the PHY TPI is down and up again, SGMII AN is not triggered and hence no new in-band message from PHY to MAC side SGMII.
This could cause an issue during power up, when PHY is up prior to MAC. At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t receive new in-band message from TI PHY with correct link status, speed and duplex info.
As suggested by TI, implemented a SW solution here to retrigger SGMII Auto-Neg whenever there is a link change.
v2: Add Fixes tag in commit message.
Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy") Cc: stable@vger.kernel.org # 5.4.x Signed-off-by: Sit, Michael Wei Hong michael.wei.hong.sit@intel.com Reviewed-by: Voon Weifeng weifeng.voon@intel.com Signed-off-by: Tan Tee Min tee.min.tan@linux.intel.com Reviewed-by: Andrew Lunn andrew@lunn.ch Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.co... Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/phy/dp83867.c | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+)
--- a/drivers/net/phy/dp83867.c +++ b/drivers/net/phy/dp83867.c @@ -137,6 +137,7 @@ #define DP83867_DOWNSHIFT_2_COUNT 2 #define DP83867_DOWNSHIFT_4_COUNT 4 #define DP83867_DOWNSHIFT_8_COUNT 8 +#define DP83867_SGMII_AUTONEG_EN BIT(7)
/* CFG3 bits */ #define DP83867_CFG3_INT_OE BIT(7) @@ -855,6 +856,32 @@ static int dp83867_phy_reset(struct phy_ DP83867_PHYCR_FORCE_LINK_GOOD, 0); }
+static void dp83867_link_change_notify(struct phy_device *phydev) +{ + /* There is a limitation in DP83867 PHY device where SGMII AN is + * only triggered once after the device is booted up. Even after the + * PHY TPI is down and up again, SGMII AN is not triggered and + * hence no new in-band message from PHY to MAC side SGMII. + * This could cause an issue during power up, when PHY is up prior + * to MAC. At this condition, once MAC side SGMII is up, MAC side + * SGMII wouldn`t receive new in-band message from TI PHY with + * correct link status, speed and duplex info. + * Thus, implemented a SW solution here to retrigger SGMII Auto-Neg + * whenever there is a link change. + */ + if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { + int val = 0; + + val = phy_clear_bits(phydev, DP83867_CFG2, + DP83867_SGMII_AUTONEG_EN); + if (val < 0) + return; + + phy_set_bits(phydev, DP83867_CFG2, + DP83867_SGMII_AUTONEG_EN); + } +} + static struct phy_driver dp83867_driver[] = { { .phy_id = DP83867_PHY_ID, @@ -879,6 +906,8 @@ static struct phy_driver dp83867_driver[
.suspend = genphy_suspend, .resume = genphy_resume, + + .link_change_notify = dp83867_link_change_notify, }, }; module_phy_driver(dp83867_driver);