[PATCH AUTOSEL 6.6 078/104] ARM64: dts: marvell: Fix some common switch mistakes

16 Jan 2024

From: Linus Walleij linus.walleij@linaro.org
[ Upstream commit 605a5f5d406df0c01d92e36a7b5419ffaf62a4ce ]
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@
Reviewed-by: Andrew Lunn andrew@lunn.ch
Signed-off-by: Linus Walleij linus.walleij@linaro.org
Reviewed-by: Florian Fainelli florian.fainelli@broadcom.com
Signed-off-by: David S. Miller davem@davemloft.net
Signed-off-by: Sasha Levin sashal@kernel.org
---
 .../marvell/armada-3720-espressobin-ultra.dts | 14 +--
 .../dts/marvell/armada-3720-espressobin.dtsi  | 20 ++---
 .../dts/marvell/armada-3720-gl-mv1000.dts     | 20 ++---
 .../dts/marvell/armada-3720-turris-mox.dts    | 85 +++++++++++--------
 .../boot/dts/marvell/armada-7040-mochabin.dts | 24 +++---
 .../marvell/armada-8040-clearfog-gt-8k.dts    | 22 ++---
 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi   | 42 +++++----
 7 files changed, 115 insertions(+), 112 deletions(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
index f9abef8dcc94..870bb380a40a 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -126,32 +126,32 @@ &switch0 {
reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
-	ports {
-		switch0port1: port@1 {
+	ethernet-ports {
+		switch0port1: ethernet-port@1 {
    		reg = <1>;
    		label = "lan0";
    		phy-handle = <&switch0phy0>;
    	};
-		switch0port2: port@2 {
+		switch0port2: ethernet-port@2 {
    		reg = <2>;
    		label = "lan1";
    		phy-handle = <&switch0phy1>;
    	};
-		switch0port3: port@3 {
+		switch0port3: ethernet-port@3 {
    		reg = <3>;
    		label = "lan2";
    		phy-handle = <&switch0phy2>;
    	};
-		switch0port4: port@4 {
+		switch0port4: ethernet-port@4 {
    		reg = <4>;
    		label = "lan3";
    		phy-handle = <&switch0phy3>;
    	};
-		switch0port5: port@5 {
+		switch0port5: ethernet-port@5 {
    		reg = <5>;
    		label = "wan";
    		phy-handle = <&extphy>;
@@ -160,7 +160,7 @@ switch0port5: port@5 {
    };
mdio {
-		switch0phy3: switch0phy3@14 {
+		switch0phy3: ethernet-phy@14 {
    		reg = <0x14>;
    	};
    };
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index 5fc613d24151..86ec0df1c676 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -145,19 +145,17 @@ &usb2 {
 };
&mdio {
-	switch0: switch0@1 {
+	switch0: ethernet-switch@1 {
    	compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
    	reg = <1>;
dsa,member = <0 0>;
-		ports {
+		ethernet-ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0port0: port@0 {
+			switch0port0: ethernet-port@0 {
    			reg = <0>;
    			label = "cpu";
    			ethernet = <&eth0>;
@@ -168,19 +166,19 @@ fixed-link {
    			};
    		};
-			switch0port1: port@1 {
+			switch0port1: ethernet-port@1 {
    			reg = <1>;
    			label = "wan";
    			phy-handle = <&switch0phy0>;
    		};
-			switch0port2: port@2 {
+			switch0port2: ethernet-port@2 {
    			reg = <2>;
    			label = "lan0";
    			phy-handle = <&switch0phy1>;
    		};
-			switch0port3: port@3 {
+			switch0port3: ethernet-port@3 {
    			reg = <3>;
    			label = "lan1";
    			phy-handle = <&switch0phy2>;
@@ -192,13 +190,13 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
    			reg = <0x13>;
    		};
    	};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
index b1b45b4fa9d4..63fbc8352161 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
@@ -152,31 +152,29 @@ &uart0 {
 };
&mdio {
-	switch0: switch0@1 {
+	switch0: ethernet-switch@1 {
    	compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
    	reg = <1>;
dsa,member = <0 0>;
-		ports: ports {
+		ports: ethernet-ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			port@0 {
+			ethernet-port@0 {
    			reg = <0>;
    			label = "cpu";
    			ethernet = <&eth0>;
    		};
-			port@1 {
+			ethernet-port@1 {
    			reg = <1>;
    			label = "wan";
    			phy-handle = <&switch0phy0>;
    		};
-			port@2 {
+			ethernet-port@2 {
    			reg = <2>;
    			label = "lan0";
    			phy-handle = <&switch0phy1>;
@@ -185,7 +183,7 @@ port@2 {
    			nvmem-cell-names = "mac-address";
    		};
-			port@3 {
+			ethernet-port@3 {
    			reg = <3>;
    			label = "lan1";
    			phy-handle = <&switch0phy2>;
@@ -199,13 +197,13 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
    			reg = <0x13>;
    		};
    	};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index 9eab2bb22134..66cd98b67744 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -304,7 +304,13 @@ phy1: ethernet-phy@1 {
    	reg = <1>;
    };
-	/* switch nodes are enabled by U-Boot if modules are present */
+	/*
+	 * NOTE: switch nodes are enabled by U-Boot if modules are present
+	 * DO NOT change this node name (switch0@10) even if it is not following
+	 * conventions! Deployed U-Boot binaries are explicitly looking for
+	 * this node in order to augment the device tree!
+	 * Also do not touch the "ports" or "port@n" nodes. These are also ABI.
+	 */
    switch0@10 {
    	compatible = "marvell,mv88e6190";
    	reg = <0x10>;
@@ -317,35 +323,35 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy1: switch0phy1@1 {
+			switch0phy1: ethernet-phy@1 {
    			reg = <0x1>;
    		};
-			switch0phy2: switch0phy2@2 {
+			switch0phy2: ethernet-phy@2 {
    			reg = <0x2>;
    		};
-			switch0phy3: switch0phy3@3 {
+			switch0phy3: ethernet-phy@3 {
    			reg = <0x3>;
    		};
-			switch0phy4: switch0phy4@4 {
+			switch0phy4: ethernet-phy@4 {
    			reg = <0x4>;
    		};
-			switch0phy5: switch0phy5@5 {
+			switch0phy5: ethernet-phy@5 {
    			reg = <0x5>;
    		};
-			switch0phy6: switch0phy6@6 {
+			switch0phy6: ethernet-phy@6 {
    			reg = <0x6>;
    		};
-			switch0phy7: switch0phy7@7 {
+			switch0phy7: ethernet-phy@7 {
    			reg = <0x7>;
    		};
-			switch0phy8: switch0phy8@8 {
+			switch0phy8: ethernet-phy@8 {
    			reg = <0x8>;
    		};
    	};
@@ -430,6 +436,7 @@ port-sfp@a {
    	};
    };
+	/* NOTE: this node name is ABI, don't change it! */
    switch0@2 {
    	compatible = "marvell,mv88e6085";
    	reg = <0x2>;
@@ -442,19 +449,19 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy1_topaz: switch0phy1@11 {
+			switch0phy1_topaz: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch0phy2_topaz: switch0phy2@12 {
+			switch0phy2_topaz: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch0phy3_topaz: switch0phy3@13 {
+			switch0phy3_topaz: ethernet-phy@13 {
    			reg = <0x13>;
    		};
-			switch0phy4_topaz: switch0phy4@14 {
+			switch0phy4_topaz: ethernet-phy@14 {
    			reg = <0x14>;
    		};
    	};
@@ -497,6 +504,7 @@ port@5 {
    	};
    };
+	/* NOTE: this node name is ABI, don't change it! */
    switch1@11 {
    	compatible = "marvell,mv88e6190";
    	reg = <0x11>;
@@ -509,35 +517,35 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch1phy1: switch1phy1@1 {
+			switch1phy1: ethernet-phy@1 {
    			reg = <0x1>;
    		};
-			switch1phy2: switch1phy2@2 {
+			switch1phy2: ethernet-phy@2 {
    			reg = <0x2>;
    		};
-			switch1phy3: switch1phy3@3 {
+			switch1phy3: ethernet-phy@3 {
    			reg = <0x3>;
    		};
-			switch1phy4: switch1phy4@4 {
+			switch1phy4: ethernet-phy@4 {
    			reg = <0x4>;
    		};
-			switch1phy5: switch1phy5@5 {
+			switch1phy5: ethernet-phy@5 {
    			reg = <0x5>;
    		};
-			switch1phy6: switch1phy6@6 {
+			switch1phy6: ethernet-phy@6 {
    			reg = <0x6>;
    		};
-			switch1phy7: switch1phy7@7 {
+			switch1phy7: ethernet-phy@7 {
    			reg = <0x7>;
    		};
-			switch1phy8: switch1phy8@8 {
+			switch1phy8: ethernet-phy@8 {
    			reg = <0x8>;
    		};
    	};
@@ -622,6 +630,7 @@ port-sfp@a {
    	};
    };
+	/* NOTE: this node name is ABI, don't change it! */
    switch1@2 {
    	compatible = "marvell,mv88e6085";
    	reg = <0x2>;
@@ -634,19 +643,19 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch1phy1_topaz: switch1phy1@11 {
+			switch1phy1_topaz: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch1phy2_topaz: switch1phy2@12 {
+			switch1phy2_topaz: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch1phy3_topaz: switch1phy3@13 {
+			switch1phy3_topaz: ethernet-phy@13 {
    			reg = <0x13>;
    		};
-			switch1phy4_topaz: switch1phy4@14 {
+			switch1phy4_topaz: ethernet-phy@14 {
    			reg = <0x14>;
    		};
    	};
@@ -689,6 +698,7 @@ port@5 {
    	};
    };
+	/* NOTE: this node name is ABI, don't change it! */
    switch2@12 {
    	compatible = "marvell,mv88e6190";
    	reg = <0x12>;
@@ -701,35 +711,35 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch2phy1: switch2phy1@1 {
+			switch2phy1: ethernet-phy@1 {
    			reg = <0x1>;
    		};
-			switch2phy2: switch2phy2@2 {
+			switch2phy2: ethernet-phy@2 {
    			reg = <0x2>;
    		};
-			switch2phy3: switch2phy3@3 {
+			switch2phy3: ethernet-phy@3 {
    			reg = <0x3>;
    		};
-			switch2phy4: switch2phy4@4 {
+			switch2phy4: ethernet-phy@4 {
    			reg = <0x4>;
    		};
-			switch2phy5: switch2phy5@5 {
+			switch2phy5: ethernet-phy@5 {
    			reg = <0x5>;
    		};
-			switch2phy6: switch2phy6@6 {
+			switch2phy6: ethernet-phy@6 {
    			reg = <0x6>;
    		};
-			switch2phy7: switch2phy7@7 {
+			switch2phy7: ethernet-phy@7 {
    			reg = <0x7>;
    		};
-			switch2phy8: switch2phy8@8 {
+			switch2phy8: ethernet-phy@8 {
    			reg = <0x8>;
    		};
    	};
@@ -805,6 +815,7 @@ port-sfp@a {
    	};
    };
+	/* NOTE: this node name is ABI, don't change it! */
    switch2@2 {
    	compatible = "marvell,mv88e6085";
    	reg = <0x2>;
@@ -817,19 +828,19 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch2phy1_topaz: switch2phy1@11 {
+			switch2phy1_topaz: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch2phy2_topaz: switch2phy2@12 {
+			switch2phy2_topaz: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch2phy3_topaz: switch2phy3@13 {
+			switch2phy3_topaz: ethernet-phy@13 {
    			reg = <0x13>;
    		};
-			switch2phy4_topaz: switch2phy4@14 {
+			switch2phy4_topaz: ethernet-phy@14 {
    			reg = <0x14>;
    		};
    	};
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
index 48202810bf78..40b7ee7ead72 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -301,10 +301,8 @@ eth2phy: ethernet-phy@1 {
    };
/* 88E6141 Topaz switch */
-	switch: switch@3 {
+	switch: ethernet-switch@3 {
    	compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
    	reg = <3>;
pinctrl-names = "default";
@@ -314,35 +312,35 @@ switch: switch@3 {
    	interrupt-parent = <&cp0_gpio1>;
    	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
-		ports {
+		ethernet-ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			swport1: port@1 {
+			swport1: ethernet-port@1 {
    			reg = <1>;
    			label = "lan0";
    			phy-handle = <&swphy1>;
    		};
-			swport2: port@2 {
+			swport2: ethernet-port@2 {
    			reg = <2>;
    			label = "lan1";
    			phy-handle = <&swphy2>;
    		};
-			swport3: port@3 {
+			swport3: ethernet-port@3 {
    			reg = <3>;
    			label = "lan2";
    			phy-handle = <&swphy3>;
    		};
-			swport4: port@4 {
+			swport4: ethernet-port@4 {
    			reg = <4>;
    			label = "lan3";
    			phy-handle = <&swphy4>;
    		};
-			port@5 {
+			ethernet-port@5 {
    			reg = <5>;
    			label = "cpu";
    			ethernet = <&cp0_eth1>;
@@ -355,19 +353,19 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			swphy1: swphy1@17 {
+			swphy1: ethernet-phy@17 {
    			reg = <17>;
    		};
-			swphy2: swphy2@18 {
+			swphy2: ethernet-phy@18 {
    			reg = <18>;
    		};
-			swphy3: swphy3@19 {
+			swphy3: ethernet-phy@19 {
    			reg = <19>;
    		};
-			swphy4: swphy4@20 {
+			swphy4: ethernet-phy@20 {
    			reg = <20>;
    		};
    	};
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index 4125202028c8..67892f0d2863 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -497,42 +497,42 @@ ge_phy: ethernet-phy@0 {
    	reset-deassert-us = <10000>;
    };
-	switch0: switch0@4 {
+	switch0: ethernet-switch@4 {
    	compatible = "marvell,mv88e6085";
    	reg = <4>;
    	pinctrl-names = "default";
    	pinctrl-0 = <&cp1_switch_reset_pins>;
    	reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>;
-		ports {
+		ethernet-ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			port@1 {
+			ethernet-port@1 {
    			reg = <1>;
    			label = "lan2";
    			phy-handle = <&switch0phy0>;
    		};
-			port@2 {
+			ethernet-port@2 {
    			reg = <2>;
    			label = "lan1";
    			phy-handle = <&switch0phy1>;
    		};
-			port@3 {
+			ethernet-port@3 {
    			reg = <3>;
    			label = "lan4";
    			phy-handle = <&switch0phy2>;
    		};
-			port@4 {
+			ethernet-port@4 {
    			reg = <4>;
    			label = "lan3";
    			phy-handle = <&switch0phy3>;
    		};
-			port@5 {
+			ethernet-port@5 {
    			reg = <5>;
    			label = "cpu";
    			ethernet = <&cp1_eth2>;
@@ -545,19 +545,19 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
    			reg = <0x11>;
    		};
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
    			reg = <0x12>;
    		};
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
    			reg = <0x13>;
    		};
-			switch0phy3: switch0phy3@14 {
+			switch0phy3: ethernet-phy@14 {
    			reg = <0x14>;
    		};
    	};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 47d45ff3d6f5..6fcc34f7b464 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -207,11 +207,9 @@ phy0: ethernet-phy@0 {
    	reg = <0>;
    };
-	switch6: switch0@6 {
+	switch6: ethernet-switch@6 {
    	/* Actual device is MV88E6393X */
    	compatible = "marvell,mv88e6190";
-		#address-cells = <1>;
-		#size-cells = <0>;
    	reg = <6>;
    	interrupt-parent = <&cp0_gpio1>;
    	interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
@@ -220,59 +218,59 @@ switch6: switch0@6 {
dsa,member = <0 0>;
-		ports {
+		ethernet-ports {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			port@1 {
+			ethernet-port@1 {
    			reg = <1>;
    			label = "p1";
    			phy-handle = <&switch0phy1>;
    		};
-			port@2 {
+			ethernet-port@2 {
    			reg = <2>;
    			label = "p2";
    			phy-handle = <&switch0phy2>;
    		};
-			port@3 {
+			ethernet-port@3 {
    			reg = <3>;
    			label = "p3";
    			phy-handle = <&switch0phy3>;
    		};
-			port@4 {
+			ethernet-port@4 {
    			reg = <4>;
    			label = "p4";
    			phy-handle = <&switch0phy4>;
    		};
-			port@5 {
+			ethernet-port@5 {
    			reg = <5>;
    			label = "p5";
    			phy-handle = <&switch0phy5>;
    		};
-			port@6 {
+			ethernet-port@6 {
    			reg = <6>;
    			label = "p6";
    			phy-handle = <&switch0phy6>;
    		};
-			port@7 {
+			ethernet-port@7 {
    			reg = <7>;
    			label = "p7";
    			phy-handle = <&switch0phy7>;
    		};
-			port@8 {
+			ethernet-port@8 {
    			reg = <8>;
    			label = "p8";
    			phy-handle = <&switch0phy8>;
    		};
-			port@9 {
+			ethernet-port@9 {
    			reg = <9>;
    			label = "p9";
    			phy-mode = "10gbase-r";
@@ -280,7 +278,7 @@ port@9 {
    			managed = "in-band-status";
    		};
-			port@a {
+			ethernet-port@a {
    			reg = <10>;
    			ethernet = <&cp0_eth0>;
    			phy-mode = "10gbase-r";
@@ -293,35 +291,35 @@ mdio {
    		#address-cells = <1>;
    		#size-cells = <0>;
-			switch0phy1: switch0phy1@1 {
+			switch0phy1: ethernet-phy@1 {
    			reg = <0x1>;
    		};
-			switch0phy2: switch0phy2@2 {
+			switch0phy2: ethernet-phy@2 {
    			reg = <0x2>;
    		};
-			switch0phy3: switch0phy3@3 {
+			switch0phy3: ethernet-phy@3 {
    			reg = <0x3>;
    		};
-			switch0phy4: switch0phy4@4 {
+			switch0phy4: ethernet-phy@4 {
    			reg = <0x4>;
    		};
-			switch0phy5: switch0phy5@5 {
+			switch0phy5: ethernet-phy@5 {
    			reg = <0x5>;
    		};
-			switch0phy6: switch0phy6@6 {
+			switch0phy6: ethernet-phy@6 {
    			reg = <0x6>;
    		};
-			switch0phy7: switch0phy7@7 {
+			switch0phy7: ethernet-phy@7 {
    			reg = <0x7>;
    		};
-			switch0phy8: switch0phy8@8 {
+			switch0phy8: ethernet-phy@8 {
    			reg = <0x8>;
    		};
    	};
-- 
2.43.0



    

2025

2024

2023

2022

2021

2020

2019

2018

2017

[PATCH AUTOSEL 6.6 078/104] ARM64: dts: marvell: Fix some common switch mistakes