From: Joakim Zhang qiangqing.zhang@nxp.com

commit 5ec55823438e850c91c6b92aec93fb04ebde29e2 upstream.

This patch intends to add clocks management for stmmac driver:

If CONFIG_PM enabled: 1. Keep clocks disabled after driver probed. 2. Enable clocks when up the net device, and disable clocks when down the net device.

If CONFIG_PM disabled: Keep clocks always enabled after driver probed.

Note: 1. It is fine for ethtool, since the way of implementing ethtool_ops::begin in stmmac is only can be accessed when interface is enabled, so the clocks are ticked. 2. The MDIO bus has a different life cycle to the MAC, need ensure clocks are enabled when _mdio_read/write() need clocks, because these functions can be called while the interface it not opened.

Stable backport notes: When run below command to remove ethernet driver on stratix10 platform, there will be warning trace as below:

$ cd /sys/class/net/eth0/device/driver/ $ echo ff800000.ethernet > unbind

WARNING: CPU: 3 PID: 386 at drivers/clk/clk.c:810 clk_core_unprepare+0x114/0x274 Modules linked in: sch_fq_codel CPU: 3 PID: 386 Comm: sh Tainted: G W 5.10.74-yocto-standard #1 Hardware name: SoCFPGA Stratix 10 SoCDK (DT) pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--) pc : clk_core_unprepare+0x114/0x274 lr : clk_core_unprepare+0x114/0x274 sp : ffff800011bdbb10 clk_core_unprepare+0x114/0x274 clk_unprepare+0x38/0x50 stmmac_remove_config_dt+0x40/0x80 stmmac_pltfr_remove+0x64/0x80 platform_drv_remove+0x38/0x60 ... .. el0_sync_handler+0x1a4/0x1b0 el0_sync+0x180/0x1c0 This issue is introduced by introducing upstream commit 8f269102baf7 ("net: stmmac: disable clocks in stmmac_remove_config_dt()")

But in latest mainline kernel, there is no this issue. Because this patch improved clocks management for stmmac driver. Therefore, backport it and its fixing patches to stable kernel v5.10.

Reviewed-by: Andrew Lunn andrew@lunn.ch Signed-off-by: Joakim Zhang qiangqing.zhang@nxp.com Signed-off-by: David S. Miller davem@davemloft.net Cc: stable@vger.kernel.org Signed-off-by: Meng Li Meng.Li@windriver.com --- drivers/net/ethernet/stmicro/stmmac/stmmac.h | 1 + .../net/ethernet/stmicro/stmmac/stmmac_main.c | 75 ++++++++++-- .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 111 ++++++++++++++---- .../ethernet/stmicro/stmmac/stmmac_platform.c | 24 +++- 4 files changed, 174 insertions(+), 37 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h index 727e68dfaf1c..a4ca283e0228 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h @@ -270,6 +270,7 @@ void stmmac_disable_eee_mode(struct stmmac_priv *priv); bool stmmac_eee_init(struct stmmac_priv *priv); int stmmac_reinit_queues(struct net_device *dev, u32 rx_cnt, u32 tx_cnt); int stmmac_reinit_ringparam(struct net_device *dev, u32 rx_size, u32 tx_size); +int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled);

#if IS_ENABLED(CONFIG_STMMAC_SELFTESTS) void stmmac_selftest_run(struct net_device *dev, diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 0ac61e7ab43c..498962c4b59e 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -28,6 +28,7 @@ #include <linux/if_vlan.h> #include <linux/dma-mapping.h> #include <linux/slab.h> +#include <linux/pm_runtime.h> #include <linux/prefetch.h> #include <linux/pinctrl/consumer.h> #ifdef CONFIG_DEBUG_FS @@ -113,6 +114,28 @@ static void stmmac_exit_fs(struct net_device *dev);

#define STMMAC_COAL_TIMER(x) (jiffies + usecs_to_jiffies(x))

+int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled) +{ + int ret = 0; + + if (enabled) { + ret = clk_prepare_enable(priv->plat->stmmac_clk); + if (ret) + return ret; + ret = clk_prepare_enable(priv->plat->pclk); + if (ret) { + clk_disable_unprepare(priv->plat->stmmac_clk); + return ret; + } + } else { + clk_disable_unprepare(priv->plat->stmmac_clk); + clk_disable_unprepare(priv->plat->pclk); + } + + return ret; +} +EXPORT_SYMBOL_GPL(stmmac_bus_clks_config); + /** * stmmac_verify_args - verify the driver parameters. * Description: it checks the driver parameters and set a default in case of @@ -2792,6 +2815,12 @@ static int stmmac_open(struct net_device *dev) u32 chan; int ret;

+ ret = pm_runtime_get_sync(priv->device); + if (ret < 0) { + pm_runtime_put_noidle(priv->device); + return ret; + } + if (priv->hw->pcs != STMMAC_PCS_TBI && priv->hw->pcs != STMMAC_PCS_RTBI && priv->hw->xpcs == NULL) { @@ -2800,7 +2829,7 @@ static int stmmac_open(struct net_device *dev) netdev_err(priv->dev, "%s: Cannot attach to PHY (error: %d)\n", __func__, ret); - return ret; + goto init_phy_error; } }

@@ -2915,6 +2944,8 @@ static int stmmac_open(struct net_device *dev) free_dma_desc_resources(priv); dma_desc_error: phylink_disconnect_phy(priv->phylink); +init_phy_error: + pm_runtime_put(priv->device); return ret; }

@@ -2965,6 +2996,8 @@ static int stmmac_release(struct net_device *dev)

stmmac_release_ptp(priv);

+ pm_runtime_put(priv->device); + return 0; }

@@ -4616,6 +4649,12 @@ static int stmmac_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vi bool is_double = false; int ret;

+ ret = pm_runtime_get_sync(priv->device); + if (ret < 0) { + pm_runtime_put_noidle(priv->device); + return ret; + } + if (be16_to_cpu(proto) == ETH_P_8021AD) is_double = true;

@@ -4624,10 +4663,15 @@ static int stmmac_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vi if (priv->hw->num_vlan) { ret = stmmac_del_hw_vlan_rx_fltr(priv, ndev, priv->hw, proto, vid); if (ret) - return ret; + goto del_vlan_error; }

- return stmmac_vlan_update(priv, is_double); + ret = stmmac_vlan_update(priv, is_double); + +del_vlan_error: + pm_runtime_put(priv->device); + + return ret; }

static const struct net_device_ops stmmac_netdev_ops = { @@ -5066,6 +5110,10 @@ int stmmac_dvr_probe(struct device *device,

stmmac_check_pcs_mode(priv);

+ pm_runtime_get_noresume(device); + pm_runtime_set_active(device); + pm_runtime_enable(device); + if (priv->hw->pcs != STMMAC_PCS_TBI && priv->hw->pcs != STMMAC_PCS_RTBI) { /* MDIO bus Registration */ @@ -5103,6 +5151,11 @@ int stmmac_dvr_probe(struct device *device, stmmac_init_fs(ndev); #endif

+ /* Let pm_runtime_put() disable the clocks. + * If CONFIG_PM is not enabled, the clocks will stay powered. + */ + pm_runtime_put(device); + return ret;

error_serdes_powerup: @@ -5117,6 +5170,7 @@ int stmmac_dvr_probe(struct device *device, stmmac_napi_del(ndev); error_hw_init: destroy_workqueue(priv->wq); + stmmac_bus_clks_config(priv, false);

return ret; } @@ -5152,8 +5206,8 @@ int stmmac_dvr_remove(struct device *dev) phylink_destroy(priv->phylink); if (priv->plat->stmmac_rst) reset_control_assert(priv->plat->stmmac_rst); - clk_disable_unprepare(priv->plat->pclk); - clk_disable_unprepare(priv->plat->stmmac_clk); + pm_runtime_put(dev); + pm_runtime_disable(dev); if (priv->hw->pcs != STMMAC_PCS_TBI && priv->hw->pcs != STMMAC_PCS_RTBI) stmmac_mdio_unregister(ndev); @@ -5176,6 +5230,7 @@ int stmmac_suspend(struct device *dev) struct net_device *ndev = dev_get_drvdata(dev); struct stmmac_priv *priv = netdev_priv(ndev); u32 chan; + int ret;

if (!ndev || !netif_running(ndev)) return 0; @@ -5219,8 +5274,9 @@ int stmmac_suspend(struct device *dev) pinctrl_pm_select_sleep_state(priv->device); /* Disable clock in case of PWM is off */ clk_disable_unprepare(priv->plat->clk_ptp_ref); - clk_disable_unprepare(priv->plat->pclk); - clk_disable_unprepare(priv->plat->stmmac_clk); + ret = pm_runtime_force_suspend(dev); + if (ret) + return ret; } mutex_unlock(&priv->lock);

@@ -5286,8 +5342,9 @@ int stmmac_resume(struct device *dev) } else { pinctrl_pm_select_default_state(priv->device); /* enable the clk previously disabled */ - clk_prepare_enable(priv->plat->stmmac_clk); - clk_prepare_enable(priv->plat->pclk); + ret = pm_runtime_force_resume(dev); + if (ret) + return ret; if (priv->plat->clk_ptp_ref) clk_prepare_enable(priv->plat->clk_ptp_ref); /* reset the phy so that it's ready */ diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c index 678726c62a8a..7c1a14b256da 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c @@ -15,6 +15,7 @@ #include <linux/iopoll.h> #include <linux/mii.h> #include <linux/of_mdio.h> +#include <linux/pm_runtime.h> #include <linux/phy.h> #include <linux/property.h> #include <linux/slab.h> @@ -87,21 +88,29 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg) u32 tmp, addr, value = MII_XGMAC_BUSY; int ret;

+ ret = pm_runtime_get_sync(priv->device); + if (ret < 0) { + pm_runtime_put_noidle(priv->device); + return ret; + } + /* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000)) - return -EBUSY; + !(tmp & MII_XGMAC_BUSY), 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

if (phyreg & MII_ADDR_C45) { phyreg &= ~MII_ADDR_C45;

ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr); if (ret) - return ret; + goto err_disable_clks; } else { ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr); if (ret) - return ret; + goto err_disable_clks;

value |= MII_XGMAC_SADDR; } @@ -112,8 +121,10 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)

/* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000)) - return -EBUSY; + !(tmp & MII_XGMAC_BUSY), 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

/* Set the MII address register to read */ writel(addr, priv->ioaddr + mii_address); @@ -121,11 +132,18 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)

/* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000)) - return -EBUSY; + !(tmp & MII_XGMAC_BUSY), 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

/* Read the data from the MII data register */ - return readl(priv->ioaddr + mii_data) & GENMASK(15, 0); + ret = (int)readl(priv->ioaddr + mii_data) & GENMASK(15, 0); + +err_disable_clks: + pm_runtime_put(priv->device); + + return ret; }

static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr, @@ -138,21 +156,29 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr, u32 addr, tmp, value = MII_XGMAC_BUSY; int ret;

+ ret = pm_runtime_get_sync(priv->device); + if (ret < 0) { + pm_runtime_put_noidle(priv->device); + return ret; + } + /* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000)) - return -EBUSY; + !(tmp & MII_XGMAC_BUSY), 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

if (phyreg & MII_ADDR_C45) { phyreg &= ~MII_ADDR_C45;

ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr); if (ret) - return ret; + goto err_disable_clks; } else { ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr); if (ret) - return ret; + goto err_disable_clks;

value |= MII_XGMAC_SADDR; } @@ -164,16 +190,23 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,

/* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000)) - return -EBUSY; + !(tmp & MII_XGMAC_BUSY), 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

/* Set the MII address register to write */ writel(addr, priv->ioaddr + mii_address); writel(value, priv->ioaddr + mii_data);

/* Wait until any existing MII operation is complete */ - return readl_poll_timeout(priv->ioaddr + mii_data, tmp, - !(tmp & MII_XGMAC_BUSY), 100, 10000); + ret = readl_poll_timeout(priv->ioaddr + mii_data, tmp, + !(tmp & MII_XGMAC_BUSY), 100, 10000); + +err_disable_clks: + pm_runtime_put(priv->device); + + return ret; }

/** @@ -196,6 +229,12 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg) int data = 0; u32 v;

+ data = pm_runtime_get_sync(priv->device); + if (data < 0) { + pm_runtime_put_noidle(priv->device); + return data; + } + value |= (phyaddr << priv->hw->mii.addr_shift) & priv->hw->mii.addr_mask; value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask; @@ -216,19 +255,26 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg) }

if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY), - 100, 10000)) - return -EBUSY; + 100, 10000)) { + data = -EBUSY; + goto err_disable_clks; + }

writel(data, priv->ioaddr + mii_data); writel(value, priv->ioaddr + mii_address);

if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY), - 100, 10000)) - return -EBUSY; + 100, 10000)) { + data = -EBUSY; + goto err_disable_clks; + }

/* Read the data from the MII data register */ data = (int)readl(priv->ioaddr + mii_data) & MII_DATA_MASK;

+err_disable_clks: + pm_runtime_put(priv->device); + return data; }

@@ -247,10 +293,16 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg, struct stmmac_priv *priv = netdev_priv(ndev); unsigned int mii_address = priv->hw->mii.addr; unsigned int mii_data = priv->hw->mii.data; + int ret, data = phydata; u32 value = MII_BUSY; - int data = phydata; u32 v;

+ ret = pm_runtime_get_sync(priv->device); + if (ret < 0) { + pm_runtime_put_noidle(priv->device); + return ret; + } + value |= (phyaddr << priv->hw->mii.addr_shift) & priv->hw->mii.addr_mask; value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask; @@ -275,16 +327,23 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,

/* Wait until any existing MII operation is complete */ if (readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY), - 100, 10000)) - return -EBUSY; + 100, 10000)) { + ret = -EBUSY; + goto err_disable_clks; + }

/* Set the MII address register to write */ writel(data, priv->ioaddr + mii_data); writel(value, priv->ioaddr + mii_address);

/* Wait until any existing MII operation is complete */ - return readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY), - 100, 10000); + ret = readl_poll_timeout(priv->ioaddr + mii_address, v, !(v & MII_BUSY), + 100, 10000); + +err_disable_clks: + pm_runtime_put(priv->device); + + return ret; }

/** diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c index 48186cd32ce1..332afe8519f4 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c @@ -760,10 +760,30 @@ static int stmmac_pltfr_resume(struct device *dev)

return stmmac_resume(dev); } + +static int stmmac_runtime_suspend(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct stmmac_priv *priv = netdev_priv(ndev); + + stmmac_bus_clks_config(priv, false); + + return 0; +} + +static int stmmac_runtime_resume(struct device *dev) +{ + struct net_device *ndev = dev_get_drvdata(dev); + struct stmmac_priv *priv = netdev_priv(ndev); + + return stmmac_bus_clks_config(priv, true); +} #endif /* CONFIG_PM_SLEEP */

-SIMPLE_DEV_PM_OPS(stmmac_pltfr_pm_ops, stmmac_pltfr_suspend, - stmmac_pltfr_resume); +const struct dev_pm_ops stmmac_pltfr_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(stmmac_pltfr_suspend, stmmac_pltfr_resume) + SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL) +}; EXPORT_SYMBOL_GPL(stmmac_pltfr_pm_ops);

MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet platform support");

From: Yang Yingliang yangyingliang@huawei.com

commit 30f347ae7cc1178c431f968a89d4b4a375bc0d39 upstream

Add the missing unlock before return from stmmac_suspend() in the error handling case.

Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver") Reported-by: Hulk Robot hulkci@huawei.com Signed-off-by: Yang Yingliang yangyingliang@huawei.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Meng Li Meng.Li@windriver.com --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 498962c4b59e..51626edc6a4c 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -5275,8 +5275,10 @@ int stmmac_suspend(struct device *dev) /* Disable clock in case of PWM is off */ clk_disable_unprepare(priv->plat->clk_ptp_ref); ret = pm_runtime_force_suspend(dev); - if (ret) + if (ret) { + mutex_unlock(&priv->lock); return ret; + } } mutex_unlock(&priv->lock);

From: Wong Vee Khee vee.khee.wong@linux.intel.com

commit ab00f3e051e851a8458f0d0eb1bb426deadb6619 upstream.

In the case of MDIO bus registration failure due to no external PHY devices is connected to the MAC, clk_disable_unprepare() is called in stmmac_bus_clk_config() and intel_eth_pci_probe() respectively.

The second call in intel_eth_pci_probe() will caused the following:-

[ 16.578605] intel-eth-pci 0000:00:1e.5: No PHY found [ 16.583778] intel-eth-pci 0000:00:1e.5: stmmac_dvr_probe: MDIO bus (id: 2) registration failed [ 16.680181] ------------[ cut here ]------------ [ 16.684861] stmmac-0000:00:1e.5 already disabled [ 16.689547] WARNING: CPU: 13 PID: 2053 at drivers/clk/clk.c:952 clk_core_disable+0x96/0x1b0 [ 16.697963] Modules linked in: dwc3 iTCO_wdt mei_hdcp iTCO_vendor_support udc_core x86_pkg_temp_thermal kvm_intel marvell10g kvm sch_fq_codel nfsd irqbypass dwmac_intel(+) stmmac uio ax88179_178a pcs_xpcs phylink uhid spi_pxa2xx_platform usbnet mei_me pcspkr tpm_crb mii i2c_i801 dw_dmac dwc3_pci thermal dw_dmac_core intel_rapl_msr libphy i2c_smbus mei tpm_tis intel_th_gth tpm_tis_core tpm intel_th_acpi intel_pmc_core intel_th i915 fuse configfs snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_hda_codec snd_hda_core snd_pcm snd_timer snd soundcore [ 16.746785] CPU: 13 PID: 2053 Comm: systemd-udevd Tainted: G U 5.13.0-rc3-intel-lts #76 [ 16.756134] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-S ADP-S DRR4 CRB, BIOS ADLIFSI1.R00.1494.B00.2012031421 12/03/2020 [ 16.769465] RIP: 0010:clk_core_disable+0x96/0x1b0 [ 16.774222] Code: 00 8b 05 45 96 17 01 85 c0 7f 24 48 8b 5b 30 48 85 db 74 a5 8b 43 7c 85 c0 75 93 48 8b 33 48 c7 c7 6e 32 cc b7 e8 b2 5d 52 00 <0f> 0b 5b 5d c3 65 8b 05 76 31 18 49 89 c0 48 0f a3 05 bc 92 1a 01 [ 16.793016] RSP: 0018:ffffa44580523aa0 EFLAGS: 00010086 [ 16.798287] RAX: 0000000000000000 RBX: ffff8d7d0eb70a00 RCX: 0000000000000000 [ 16.805435] RDX: 0000000000000002 RSI: ffffffffb7c62d5f RDI: 00000000ffffffff [ 16.812610] RBP: 0000000000000287 R08: 0000000000000000 R09: ffffa445805238d0 [ 16.819759] R10: 0000000000000001 R11: 0000000000000001 R12: ffff8d7d0eb70a00 [ 16.826904] R13: ffff8d7d027370c8 R14: 0000000000000006 R15: ffffa44580523ad0 [ 16.834047] FS: 00007f9882fa2600(0000) GS:ffff8d80a0940000(0000) knlGS:0000000000000000 [ 16.842177] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 16.847966] CR2: 00007f9882bea3d8 CR3: 000000010b126001 CR4: 0000000000370ee0 [ 16.855144] Call Trace: [ 16.857614] clk_core_disable_lock+0x1b/0x30 [ 16.861941] intel_eth_pci_probe.cold+0x11d/0x136 [dwmac_intel] [ 16.867913] pci_device_probe+0xcf/0x150 [ 16.871890] really_probe+0xf5/0x3e0 [ 16.875526] driver_probe_device+0x64/0x150 [ 16.879763] device_driver_attach+0x53/0x60 [ 16.883998] __driver_attach+0x9f/0x150 [ 16.887883] ? device_driver_attach+0x60/0x60 [ 16.892288] ? device_driver_attach+0x60/0x60 [ 16.896698] bus_for_each_dev+0x77/0xc0 [ 16.900583] bus_add_driver+0x184/0x1f0 [ 16.904469] driver_register+0x6c/0xc0 [ 16.908268] ? 0xffffffffc07ae000 [ 16.911598] do_one_initcall+0x4a/0x210 [ 16.915489] ? kmem_cache_alloc_trace+0x305/0x4e0 [ 16.920247] do_init_module+0x5c/0x230 [ 16.924057] load_module+0x2894/0x2b70 [ 16.927857] ? __do_sys_finit_module+0xb5/0x120 [ 16.932441] __do_sys_finit_module+0xb5/0x120 [ 16.936845] do_syscall_64+0x42/0x80 [ 16.940476] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 16.945586] RIP: 0033:0x7f98830e5ccd [ 16.949177] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 93 31 0c 00 f7 d8 64 89 01 48 [ 16.967970] RSP: 002b:00007ffc66b60168 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 16.975583] RAX: ffffffffffffffda RBX: 000055885de35ef0 RCX: 00007f98830e5ccd [ 16.982725] RDX: 0000000000000000 RSI: 00007f98832541e3 RDI: 0000000000000012 [ 16.989868] RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000 [ 16.997042] R10: 0000000000000012 R11: 0000000000000246 R12: 00007f98832541e3 [ 17.004222] R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffc66b60328 [ 17.011369] ---[ end trace df06a3dab26b988c ]--- [ 17.016062] ------------[ cut here ]------------ [ 17.020701] stmmac-0000:00:1e.5 already unprepared

Removing the stmmac_bus_clks_config() call in stmmac_dvr_probe and let dwmac-intel to handle the unprepare and disable of the clk device.

Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver") Cc: Joakim Zhang qiangqing.zhang@nxp.com Signed-off-by: Wong Vee Khee vee.khee.wong@linux.intel.com Reviewed-by: Joakim Zhang qiangqing.zhang@nxp.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Meng Li Meng.Li@windriver.com --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 1 - 1 file changed, 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index cccf98f66ff4..4a75e73f06bb 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -5179,7 +5179,6 @@ int stmmac_dvr_probe(struct device *device, stmmac_napi_del(ndev); error_hw_init: destroy_workqueue(priv->wq); - stmmac_bus_clks_config(priv, false);

return ret; }