From: Slawomir Stepien sst@poczta.fm

[ Upstream commit 0559ef7fde67bc6c83c6eb6329dbd6649528263e ]

Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative error code. This change will ensure that this error is being passed up in the call stack, so it can be handled.

Signed-off-by: Slawomir Stepien sst@poczta.fm Signed-off-by: Jonathan Cameron Jonathan.Cameron@huawei.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/staging/iio/adc/ad7280a.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/drivers/staging/iio/adc/ad7280a.c b/drivers/staging/iio/adc/ad7280a.c index b736275c10f5..6a48ad067a8b 100644 --- a/drivers/staging/iio/adc/ad7280a.c +++ b/drivers/staging/iio/adc/ad7280a.c @@ -256,7 +256,9 @@ static int ad7280_read(struct ad7280_state *st, unsigned int devaddr, if (ret) return ret;

- __ad7280_read32(st, &tmp); + ret = __ad7280_read32(st, &tmp); + if (ret) + return ret;

if (ad7280_check_crc(st, tmp)) return -EIO; @@ -294,7 +296,9 @@ static int ad7280_read_channel(struct ad7280_state *st, unsigned int devaddr,

ad7280_delay(st);

- __ad7280_read32(st, &tmp); + ret = __ad7280_read32(st, &tmp); + if (ret) + return ret;

if (ad7280_check_crc(st, tmp)) return -EIO; @@ -327,7 +331,9 @@ static int ad7280_read_all_channels(struct ad7280_state *st, unsigned int cnt, ad7280_delay(st);

for (i = 0; i < cnt; i++) { - __ad7280_read32(st, &tmp); + ret = __ad7280_read32(st, &tmp); + if (ret) + return ret;

if (ad7280_check_crc(st, tmp)) return -EIO; @@ -370,7 +376,10 @@ static int ad7280_chain_setup(struct ad7280_state *st) return ret;

for (n = 0; n <= AD7280A_MAX_CHAIN; n++) { - __ad7280_read32(st, &val); + ret = __ad7280_read32(st, &val); + if (ret) + return ret; + if (val == 0) return n - 1;

From: Lukas Wunner lukas@wunner.de

[ Upstream commit 3c7b30f704b6f5e53eed6bf89cf2c8d1b38b02c0 ]

The BCM2835 pinctrl driver acquires a spinlock in its ->irq_enable, ->irq_disable and ->irq_set_type callbacks. Spinlocks become sleeping locks with CONFIG_PREEMPT_RT_FULL=y, therefore invocation of one of the callbacks in atomic context may cause a hard lockup if at least two GPIO pins in the same bank are used as interrupts. The issue doesn't occur with just a single interrupt pin per bank because the lock is never contended. I'm experiencing such lockups with GPIO 8 and 28 used as level-triggered interrupts, i.e. with ->irq_disable being invoked on reception of every IRQ.

The critical section protected by the spinlock is very small (one bitop and one RMW of an MMIO register), hence converting to a raw spinlock seems a better trade-off than converting the driver to threaded IRQ handling (which would increase latency to handle an interrupt).

Cc: Mathias Duckeck m.duckeck@kunbus.de Signed-off-by: Lukas Wunner lukas@wunner.de Acked-by: Julia Cartwright julia@ni.com Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c index fa530913a2c8..08925d24180b 100644 --- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c +++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c @@ -90,7 +90,7 @@ struct bcm2835_pinctrl { struct gpio_chip gpio_chip; struct pinctrl_gpio_range gpio_range;

- spinlock_t irq_lock[BCM2835_NUM_BANKS]; + raw_spinlock_t irq_lock[BCM2835_NUM_BANKS]; };

/* pins are just named GPIO0..GPIO53 */ @@ -461,10 +461,10 @@ static void bcm2835_gpio_irq_enable(struct irq_data *data) unsigned bank = GPIO_REG_OFFSET(gpio); unsigned long flags;

- spin_lock_irqsave(&pc->irq_lock[bank], flags); + raw_spin_lock_irqsave(&pc->irq_lock[bank], flags); set_bit(offset, &pc->enabled_irq_map[bank]); bcm2835_gpio_irq_config(pc, gpio, true); - spin_unlock_irqrestore(&pc->irq_lock[bank], flags); + raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags); }

static void bcm2835_gpio_irq_disable(struct irq_data *data) @@ -476,12 +476,12 @@ static void bcm2835_gpio_irq_disable(struct irq_data *data) unsigned bank = GPIO_REG_OFFSET(gpio); unsigned long flags;

- spin_lock_irqsave(&pc->irq_lock[bank], flags); + raw_spin_lock_irqsave(&pc->irq_lock[bank], flags); bcm2835_gpio_irq_config(pc, gpio, false); /* Clear events that were latched prior to clearing event sources */ bcm2835_gpio_set_bit(pc, GPEDS0, gpio); clear_bit(offset, &pc->enabled_irq_map[bank]); - spin_unlock_irqrestore(&pc->irq_lock[bank], flags); + raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags); }

static int __bcm2835_gpio_irq_set_type_disabled(struct bcm2835_pinctrl *pc, @@ -584,7 +584,7 @@ static int bcm2835_gpio_irq_set_type(struct irq_data *data, unsigned int type) unsigned long flags; int ret;

- spin_lock_irqsave(&pc->irq_lock[bank], flags); + raw_spin_lock_irqsave(&pc->irq_lock[bank], flags);

if (test_bit(offset, &pc->enabled_irq_map[bank])) ret = __bcm2835_gpio_irq_set_type_enabled(pc, gpio, type); @@ -596,7 +596,7 @@ static int bcm2835_gpio_irq_set_type(struct irq_data *data, unsigned int type) else irq_set_handler_locked(data, handle_level_irq);

- spin_unlock_irqrestore(&pc->irq_lock[bank], flags); + raw_spin_unlock_irqrestore(&pc->irq_lock[bank], flags);

return ret; } @@ -1047,7 +1047,7 @@ static int bcm2835_pinctrl_probe(struct platform_device *pdev) for_each_set_bit(offset, &events, 32) bcm2835_gpio_wr(pc, GPEDS0 + i * 4, BIT(offset));

- spin_lock_init(&pc->irq_lock[i]); + raw_spin_lock_init(&pc->irq_lock[i]); }

err = gpiochip_add_data(&pc->gpio_chip, pc);

From: Muchun Song smuchun@gmail.com

[ Upstream commit 18534df419041e6c1f4b41af56ee7d41f757815c ]

gpiod_request_commit() copies the pointer to the label passed as an argument only to be used later. But there's a chance the caller could immediately free the passed string(e.g., local variable). This could trigger a use after free when we use gpio label(e.g., gpiochip_unlock_as_irq(), gpiochip_is_requested()).

To be on the safe side: duplicate the string with kstrdup_const() so that if an unaware user passes an address to a stack-allocated buffer, we won't get the arbitrary label.

Also fix gpiod_set_consumer_name().

Signed-off-by: Muchun Song smuchun@gmail.com Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpio/gpiolib.c | 25 +++++++++++++++++++++---- include/linux/gpio/consumer.h | 6 ++++-- 2 files changed, 25 insertions(+), 6 deletions(-)

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c index a8e01d99919c..647da2649c91 100644 --- a/drivers/gpio/gpiolib.c +++ b/drivers/gpio/gpiolib.c @@ -2271,6 +2271,12 @@ static int gpiod_request_commit(struct gpio_desc *desc, const char *label) unsigned long flags; unsigned offset;

+ if (label) { + label = kstrdup_const(label, GFP_KERNEL); + if (!label) + return -ENOMEM; + } + spin_lock_irqsave(&gpio_lock, flags);

/* NOTE: gpio_request() can be called in early boot, @@ -2281,6 +2287,7 @@ static int gpiod_request_commit(struct gpio_desc *desc, const char *label) desc_set_label(desc, label ? : "?"); status = 0; } else { + kfree_const(label); status = -EBUSY; goto done; } @@ -2297,6 +2304,7 @@ static int gpiod_request_commit(struct gpio_desc *desc, const char *label)

if (status < 0) { desc_set_label(desc, NULL); + kfree_const(label); clear_bit(FLAG_REQUESTED, &desc->flags); goto done; } @@ -2392,6 +2400,7 @@ static bool gpiod_free_commit(struct gpio_desc *desc) chip->free(chip, gpio_chip_hwgpio(desc)); spin_lock_irqsave(&gpio_lock, flags); } + kfree_const(desc->label); desc_set_label(desc, NULL); clear_bit(FLAG_ACTIVE_LOW, &desc->flags); clear_bit(FLAG_REQUESTED, &desc->flags); @@ -3213,11 +3222,19 @@ EXPORT_SYMBOL_GPL(gpiod_cansleep); * @desc: gpio to set the consumer name on * @name: the new consumer name */ -void gpiod_set_consumer_name(struct gpio_desc *desc, const char *name) +int gpiod_set_consumer_name(struct gpio_desc *desc, const char *name) { - VALIDATE_DESC_VOID(desc); - /* Just overwrite whatever the previous name was */ - desc->label = name; + VALIDATE_DESC(desc); + if (name) { + name = kstrdup_const(name, GFP_KERNEL); + if (!name) + return -ENOMEM; + } + + kfree_const(desc->label); + desc_set_label(desc, name); + + return 0; } EXPORT_SYMBOL_GPL(gpiod_set_consumer_name);

diff --git a/include/linux/gpio/consumer.h b/include/linux/gpio/consumer.h index 21ddbe440030..acc4279ad5e3 100644 --- a/include/linux/gpio/consumer.h +++ b/include/linux/gpio/consumer.h @@ -142,7 +142,7 @@ int gpiod_is_active_low(const struct gpio_desc *desc); int gpiod_cansleep(const struct gpio_desc *desc);

int gpiod_to_irq(const struct gpio_desc *desc); -void gpiod_set_consumer_name(struct gpio_desc *desc, const char *name); +int gpiod_set_consumer_name(struct gpio_desc *desc, const char *name);

/* Convert between the old gpio_ and new gpiod_ interfaces */ struct gpio_desc *gpio_to_desc(unsigned gpio); @@ -465,10 +465,12 @@ static inline int gpiod_to_irq(const struct gpio_desc *desc) return -EINVAL; }

-static inline void gpiod_set_consumer_name(struct gpio_desc *desc, const char *name) +static inline int gpiod_set_consumer_name(struct gpio_desc *desc, + const char *name) { /* GPIO can never have been requested */ WARN_ON(1); + return -EINVAL; }

static inline struct gpio_desc *gpio_to_desc(unsigned gpio)

From: Long Li longli@microsoft.com

[ Upstream commit b82592199032bf7c778f861b936287e37ebc9f62 ]

If the number of NUMA nodes exceeds the number of MSI/MSI-X interrupts which are allocated for a device, the interrupt affinity spreading code fails to spread them across all nodes.

The reason is, that the spreading code starts from node 0 and continues up to the number of interrupts requested for allocation. This leaves the nodes past the last interrupt unused.

This results in interrupt concentration on the first nodes which violates the assumption of the block layer that all nodes are covered evenly. As a consequence the NUMA nodes above the number of interrupts are all assigned to hardware queue 0 and therefore NUMA node 0, which results in bad performance and has CPU hotplug implications, because queue 0 gets shut down when the last CPU of node 0 is offlined.

Go over all NUMA nodes and assign them round-robin to all requested interrupts to solve this.

[ tglx: Massaged changelog ]

Signed-off-by: Long Li longli@microsoft.com Signed-off-by: Thomas Gleixner tglx@linutronix.de Reviewed-by: Ming Lei ming.lei@redhat.com Cc: Michael Kelley mikelley@microsoft.com Link: https://lkml.kernel.org/r/20181102180248.13583-1-longli@linuxonhyperv.com Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/irq/affinity.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/kernel/irq/affinity.c b/kernel/irq/affinity.c index f4f29b9d90ee..e12cdf637c71 100644 --- a/kernel/irq/affinity.c +++ b/kernel/irq/affinity.c @@ -117,12 +117,11 @@ static int irq_build_affinity_masks(const struct irq_affinity *affd, */ if (numvecs <= nodes) { for_each_node_mask(n, nodemsk) { - cpumask_copy(masks + curvec, node_to_cpumask[n]); - if (++done == numvecs) - break; + cpumask_or(masks + curvec, masks + curvec, node_to_cpumask[n]); if (++curvec == last_affv) curvec = affd->pre_vectors; } + done = numvecs; goto out; }

From: Nickhu nickhu@andestech.com

[ Upstream commit 4c3d6174e0e17599549f636ec48ddf78627a17fe ]

When the kernel configs of ftrace and frame pointer options are choosed, the compiler option of kernel will incompatible. Error message: nds32le-linux-gcc: error: -pg and -fomit-frame-pointer are incompatible

Signed-off-by: Nickhu nickhu@andestech.com Signed-off-by: Zong Li zong@andestech.com Acked-by: Greentime Hu greentime@andestech.com Signed-off-by: Greentime Hu greentime@andestech.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/nds32/mm/Makefile | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/nds32/mm/Makefile b/arch/nds32/mm/Makefile index 6b6855852223..7c5c15ad854a 100644 --- a/arch/nds32/mm/Makefile +++ b/arch/nds32/mm/Makefile @@ -4,4 +4,8 @@ obj-y := extable.o tlb.o \

obj-$(CONFIG_ALIGNMENT_TRAP) += alignment.o obj-$(CONFIG_HIGHMEM) += highmem.o -CFLAGS_proc-n13.o += -fomit-frame-pointer + +ifdef CONFIG_FUNCTION_TRACER +CFLAGS_REMOVE_proc.o = $(CC_FLAGS_FTRACE) +endif +CFLAGS_proc.o += -fomit-frame-pointer

From: Lior David liord@codeaurora.org

[ Upstream commit 664497400c89a4d40aee51bcf48bbd2e4dc71104 ]

A successful call to wil_tx_ring takes skb reference so it will only be freed in wil_tx_complete. Consume the skb in wil_find_tx_bcast_2 to prevent memory leak.

Signed-off-by: Lior David liord@codeaurora.org Signed-off-by: Maya Erez merez@codeaurora.org Signed-off-by: Kalle Valo kvalo@codeaurora.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/ath/wil6210/txrx.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c index 6a7943e487fb..75c8aa297107 100644 --- a/drivers/net/wireless/ath/wil6210/txrx.c +++ b/drivers/net/wireless/ath/wil6210/txrx.c @@ -1313,6 +1313,8 @@ static struct wil_ring *wil_find_tx_bcast_2(struct wil6210_priv *wil, wil_dbg_txrx(wil, "BCAST DUP -> ring %d\n", i); wil_set_da_for_vring(wil, skb2, i); wil_tx_ring(wil, vif, v2, skb2); + /* successful call to wil_tx_ring takes skb2 ref */ + dev_kfree_skb_any(skb2); } else { wil_err(wil, "skb_copy failed\n"); }

From: Lorenzo Bianconi lorenzo.bianconi@redhat.com

[ Upstream commit 3831a2a0010c72e3956020cbf1057a1701a2e469 ]

In order to properly support dynack in ad-hoc mode running wpa_supplicant, take into account authentication frames for 'late ack' detection. This patch has been tested on devices mounted on offshore high-voltage stations connected through ~24Km link

Reported-by: Koen Vandeputte koen.vandeputte@ncentric.com Tested-by: Koen Vandeputte koen.vandeputte@ncentric.com Signed-off-by: Lorenzo Bianconi lorenzo.bianconi@redhat.com Signed-off-by: Kalle Valo kvalo@codeaurora.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/ath/ath9k/dynack.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath9k/dynack.c b/drivers/net/wireless/ath/ath9k/dynack.c index 7334c9b09e82..cc0dc966c512 100644 --- a/drivers/net/wireless/ath/ath9k/dynack.c +++ b/drivers/net/wireless/ath/ath9k/dynack.c @@ -187,7 +187,8 @@ void ath_dynack_sample_tx_ts(struct ath_hw *ah, struct sk_buff *skb, /* late ACK */ if (ts->ts_status & ATH9K_TXERR_XRETRY) { if (ieee80211_is_assoc_req(hdr->frame_control) || - ieee80211_is_assoc_resp(hdr->frame_control)) { + ieee80211_is_assoc_resp(hdr->frame_control) || + ieee80211_is_auth(hdr->frame_control)) { ath_dbg(common, DYNACK, "late ack\n"); ath9k_hw_setslottime(ah, (LATEACK_TO - 3) / 2); ath9k_hw_set_ack_timeout(ah, LATEACK_TO);

From: Suganath Prabu suganath-prabu.subramani@broadcom.com

[ Upstream commit dc730212e8a378763cb182b889f90c8101331332 ]

Call sas_remove_host() before removing the target devices in the driver's .remove() callback function(i.e. during driver unload time). So that driver can provide a way to allow SYNC CACHE, START STOP unit commands etc. (which are issued from SML) to the target drives during driver unload time.

Once sas_remove_host() is called before removing the target drives then driver can just clean up the resources allocated for target devices and no need to call sas_port_delete_phy(), sas_port_delete() API's as these API's internally called from sas_remove_host().

Signed-off-by: Suganath Prabu suganath-prabu.subramani@broadcom.com Reviewed-by: Bjorn Helgaas bhelgaas@google.com Reviewed-by: Andy Shevchenko andy.shevchenko@gmail.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/mpt3sas/mpt3sas_scsih.c | 2 +- drivers/scsi/mpt3sas/mpt3sas_transport.c | 7 +++++-- 2 files changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c b/drivers/scsi/mpt3sas/mpt3sas_scsih.c index 53133cfd420f..622832e55211 100644 --- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c +++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c @@ -9809,6 +9809,7 @@ static void scsih_remove(struct pci_dev *pdev)

/* release all the volumes */ _scsih_ir_shutdown(ioc); + sas_remove_host(shost); list_for_each_entry_safe(raid_device, next, &ioc->raid_device_list, list) { if (raid_device->starget) { @@ -9851,7 +9852,6 @@ static void scsih_remove(struct pci_dev *pdev) ioc->sas_hba.num_phys = 0; }

- sas_remove_host(shost); mpt3sas_base_detach(ioc); spin_lock(&gioc_lock); list_del(&ioc->list); diff --git a/drivers/scsi/mpt3sas/mpt3sas_transport.c b/drivers/scsi/mpt3sas/mpt3sas_transport.c index f8cc2677c1cd..20d36061c217 100644 --- a/drivers/scsi/mpt3sas/mpt3sas_transport.c +++ b/drivers/scsi/mpt3sas/mpt3sas_transport.c @@ -834,10 +834,13 @@ mpt3sas_transport_port_remove(struct MPT3SAS_ADAPTER *ioc, u64 sas_address, mpt3sas_port->remote_identify.sas_address, mpt3sas_phy->phy_id); mpt3sas_phy->phy_belongs_to_port = 0; - sas_port_delete_phy(mpt3sas_port->port, mpt3sas_phy->phy); + if (!ioc->remove_host) + sas_port_delete_phy(mpt3sas_port->port, + mpt3sas_phy->phy); list_del(&mpt3sas_phy->port_siblings); } - sas_port_delete(mpt3sas_port->port); + if (!ioc->remove_host) + sas_port_delete(mpt3sas_port->port); kfree(mpt3sas_port); }

From: João Paulo Rechi Vita jprvita@gmail.com

[ Upstream commit b3f2f3799a972d3863d0fdc2ab6287aef6ca631f ]

When the OS registers to handle events from the display off hotkey the EC will send a notification with 0x35 for every key press, independent of the backlight state.

The behavior of this key on Windows, with the ATKACPI driver from Asus installed, is turning off the backlight of all connected displays with a fading effect, and any cursor input or key press turning the backlight back on. The key press or cursor input that wakes up the display is also passed through to the application under the cursor or under focus.

The key that matches this behavior the closest is KEY_SCREENLOCK.

Signed-off-by: João Paulo Rechi Vita jprvita@endlessm.com Signed-off-by: Andy Shevchenko andriy.shevchenko@linux.intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/platform/x86/asus-nb-wmi.c | 1 + 1 file changed, 1 insertion(+)

diff --git a/drivers/platform/x86/asus-nb-wmi.c b/drivers/platform/x86/asus-nb-wmi.c index db2af09067db..5a00a7665f9b 100644 --- a/drivers/platform/x86/asus-nb-wmi.c +++ b/drivers/platform/x86/asus-nb-wmi.c @@ -444,6 +444,7 @@ static const struct key_entry asus_nb_wmi_keymap[] = { { KE_KEY, 0x32, { KEY_MUTE } }, { KE_KEY, 0x33, { KEY_DISPLAYTOGGLE } }, /* LCD on */ { KE_KEY, 0x34, { KEY_DISPLAY_OFF } }, /* LCD off */ + { KE_KEY, 0x35, { KEY_SCREENLOCK } }, { KE_KEY, 0x40, { KEY_PREVIOUSSONG } }, { KE_KEY, 0x41, { KEY_NEXTSONG } }, { KE_KEY, 0x43, { KEY_STOPCD } }, /* Stop/Eject */

From: Yi Wang wang.yi59@zte.com.cn

[ Upstream commit 46fda5b5067a391912cf73bf3d32c26b6a22ad09 ]

Smatch report warnings: drivers/clk/imgtec/clk-boston.c:76 clk_boston_setup() warn: possible memory leak of 'onecell' drivers/clk/imgtec/clk-boston.c:83 clk_boston_setup() warn: possible memory leak of 'onecell' drivers/clk/imgtec/clk-boston.c:90 clk_boston_setup() warn: possible memory leak of 'onecell'

'onecell' is malloced in clk_boston_setup(), but not be freed before leaving from the error handling cases.

Signed-off-by: Yi Wang wang.yi59@zte.com.cn Signed-off-by: Stephen Boyd sboyd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/imgtec/clk-boston.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/imgtec/clk-boston.c b/drivers/clk/imgtec/clk-boston.c index 15af423cc0c9..f5d54a64d33c 100644 --- a/drivers/clk/imgtec/clk-boston.c +++ b/drivers/clk/imgtec/clk-boston.c @@ -73,27 +73,32 @@ static void __init clk_boston_setup(struct device_node *np) hw = clk_hw_register_fixed_rate(NULL, "input", NULL, 0, in_freq); if (IS_ERR(hw)) { pr_err("failed to register input clock: %ld\n", PTR_ERR(hw)); - return; + goto error; } onecell->hws[BOSTON_CLK_INPUT] = hw;

hw = clk_hw_register_fixed_rate(NULL, "sys", "input", 0, sys_freq); if (IS_ERR(hw)) { pr_err("failed to register sys clock: %ld\n", PTR_ERR(hw)); - return; + goto error; } onecell->hws[BOSTON_CLK_SYS] = hw;

hw = clk_hw_register_fixed_rate(NULL, "cpu", "input", 0, cpu_freq); if (IS_ERR(hw)) { pr_err("failed to register cpu clock: %ld\n", PTR_ERR(hw)); - return; + goto error; } onecell->hws[BOSTON_CLK_CPU] = hw;

err = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, onecell); if (err) pr_err("failed to add DT provider: %d\n", err); + + return; + +error: + kfree(onecell); }

/*

From: Colin Ian King colin.king@canonical.com

[ Upstream commit 53bb565fc5439f2c8c57a786feea5946804aa3e9 ]

In the expression "word1 << 16", word1 starts as u16, but is promoted to a signed int, then sign-extended to resource_size_t, which is probably not what was intended. Cast to resource_size_t to avoid the sign extension.

This fixes an identical issue as fixed by commit 0b2d70764bb3 ("x86/PCI: Fix Broadcom CNB20LE unintended sign extension") back in 2014.

Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension")

Fixes: 3f6ea84a3035 ("PCI: read memory ranges out of Broadcom CNB20LE host bridge") Signed-off-by: Colin Ian King colin.king@canonical.com Signed-off-by: Bjorn Helgaas helgaas@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- arch/x86/pci/broadcom_bus.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/pci/broadcom_bus.c b/arch/x86/pci/broadcom_bus.c index 526536c81ddc..ca1e8e6dccc8 100644 --- a/arch/x86/pci/broadcom_bus.c +++ b/arch/x86/pci/broadcom_bus.c @@ -50,8 +50,8 @@ static void __init cnb20le_res(u8 bus, u8 slot, u8 func) word1 = read_pci_config_16(bus, slot, func, 0xc0); word2 = read_pci_config_16(bus, slot, func, 0xc2); if (word1 != word2) { - res.start = (word1 << 16) | 0x0000; - res.end = (word2 << 16) | 0xffff; + res.start = ((resource_size_t) word1 << 16) | 0x0000; + res.end = ((resource_size_t) word2 << 16) | 0xffff; res.flags = IORESOURCE_MEM; update_res(info, res.start, res.end, res.flags, 0); }

From: "Paul E. McKenney" paulmck@linux.vnet.ibm.com

[ Upstream commit 0607ba8403c4cdb253f8c5200ecf654dfb7790cc ]

Ever since cdf7abc4610a ("srcu: Allow use of Tiny/Tree SRCU from both process and interrupt context"), it has been permissible to use SRCU read-side critical sections in interrupt context. This allows __call_srcu() to use SRCU read-side critical sections to prevent a new SRCU grace period from ending before the call to either srcu_funnel_gp_start() or srcu_funnel_exp_start completes, thus preventing SRCU grace-period counter overflow during that time.

Note that this does not permit removal of the counter-wrap checks in srcu_gp_end(). These check are necessary to handle the case where a given CPU does not interact at all with SRCU for an extended time period.

This commit therefore adds an SRCU read-side critical section to __call_srcu() in order to prevent grace period counter wrap during the funnel-locking process.

Signed-off-by: Paul E. McKenney paulmck@linux.vnet.ibm.com Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/rcu/srcutree.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/kernel/rcu/srcutree.c b/kernel/rcu/srcutree.c index 1ff17e297f0c..4b0a6e319b2c 100644 --- a/kernel/rcu/srcutree.c +++ b/kernel/rcu/srcutree.c @@ -853,6 +853,7 @@ void __call_srcu(struct srcu_struct *sp, struct rcu_head *rhp, rcu_callback_t func, bool do_norm) { unsigned long flags; + int idx; bool needexp = false; bool needgp = false; unsigned long s; @@ -866,6 +867,7 @@ void __call_srcu(struct srcu_struct *sp, struct rcu_head *rhp, return; } rhp->func = func; + idx = srcu_read_lock(sp); local_irq_save(flags); sdp = this_cpu_ptr(sp->sda); spin_lock_rcu_node(sdp); @@ -887,6 +889,7 @@ void __call_srcu(struct srcu_struct *sp, struct rcu_head *rhp, srcu_funnel_gp_start(sp, sdp, s, do_norm); else if (needexp) srcu_funnel_exp_start(sp, sdp->mynode, s); + srcu_read_unlock(sp, idx); }

/**

From: Eric Biggers ebiggers@google.com

[ Upstream commit 0a6a40c2a8c184a2fb467efacfb1cd338d719e0b ]

In the "aes-fixed-time" AES implementation, disable interrupts while accessing the S-box, in order to make cache-timing attacks more difficult. Previously it was possible for the CPU to be interrupted while the S-box was loaded into L1 cache, potentially evicting the cachelines and causing later table lookups to be time-variant.

In tests I did on x86 and ARM, this doesn't affect performance significantly. Responsiveness is potentially a concern, but interrupts are only disabled for a single AES block.

Note that even after this change, the implementation still isn't necessarily guaranteed to be constant-time; see https://cr.yp.to/antiforgery/cachetiming-20050414.pdf for a discussion of the many difficulties involved in writing truly constant-time AES software. But it's valuable to make such attacks more difficult.

Reviewed-by: Ard Biesheuvel ard.biesheuvel@linaro.org Signed-off-by: Eric Biggers ebiggers@google.com Signed-off-by: Herbert Xu herbert@gondor.apana.org.au Signed-off-by: Sasha Levin sashal@kernel.org --- crypto/Kconfig | 3 ++- crypto/aes_ti.c | 18 ++++++++++++++++++ 2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/crypto/Kconfig b/crypto/Kconfig index 59e32623a7ce..0fb9586766a7 100644 --- a/crypto/Kconfig +++ b/crypto/Kconfig @@ -1056,7 +1056,8 @@ config CRYPTO_AES_TI 8 for decryption), this implementation only uses just two S-boxes of 256 bytes each, and attempts to eliminate data dependent latencies by prefetching the entire table into the cache at the start of each - block. + block. Interrupts are also disabled to avoid races where cachelines + are evicted when the CPU is interrupted to do something else.

config CRYPTO_AES_586 tristate "AES cipher algorithms (i586)" diff --git a/crypto/aes_ti.c b/crypto/aes_ti.c index 03023b2290e8..1ff9785b30f5 100644 --- a/crypto/aes_ti.c +++ b/crypto/aes_ti.c @@ -269,6 +269,7 @@ static void aesti_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) const u32 *rkp = ctx->key_enc + 4; int rounds = 6 + ctx->key_length / 4; u32 st0[4], st1[4]; + unsigned long flags; int round;

st0[0] = ctx->key_enc[0] ^ get_unaligned_le32(in); @@ -276,6 +277,12 @@ static void aesti_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) st0[2] = ctx->key_enc[2] ^ get_unaligned_le32(in + 8); st0[3] = ctx->key_enc[3] ^ get_unaligned_le32(in + 12);

+ /* + * Temporarily disable interrupts to avoid races where cachelines are + * evicted when the CPU is interrupted to do something else. + */ + local_irq_save(flags); + st0[0] ^= __aesti_sbox[ 0] ^ __aesti_sbox[128]; st0[1] ^= __aesti_sbox[32] ^ __aesti_sbox[160]; st0[2] ^= __aesti_sbox[64] ^ __aesti_sbox[192]; @@ -300,6 +307,8 @@ static void aesti_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) put_unaligned_le32(subshift(st1, 1) ^ rkp[5], out + 4); put_unaligned_le32(subshift(st1, 2) ^ rkp[6], out + 8); put_unaligned_le32(subshift(st1, 3) ^ rkp[7], out + 12); + + local_irq_restore(flags); }

static void aesti_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) @@ -308,6 +317,7 @@ static void aesti_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) const u32 *rkp = ctx->key_dec + 4; int rounds = 6 + ctx->key_length / 4; u32 st0[4], st1[4]; + unsigned long flags; int round;

st0[0] = ctx->key_dec[0] ^ get_unaligned_le32(in); @@ -315,6 +325,12 @@ static void aesti_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) st0[2] = ctx->key_dec[2] ^ get_unaligned_le32(in + 8); st0[3] = ctx->key_dec[3] ^ get_unaligned_le32(in + 12);

+ /* + * Temporarily disable interrupts to avoid races where cachelines are + * evicted when the CPU is interrupted to do something else. + */ + local_irq_save(flags); + st0[0] ^= __aesti_inv_sbox[ 0] ^ __aesti_inv_sbox[128]; st0[1] ^= __aesti_inv_sbox[32] ^ __aesti_inv_sbox[160]; st0[2] ^= __aesti_inv_sbox[64] ^ __aesti_inv_sbox[192]; @@ -339,6 +355,8 @@ static void aesti_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in) put_unaligned_le32(inv_subshift(st1, 1) ^ rkp[5], out + 4); put_unaligned_le32(inv_subshift(st1, 2) ^ rkp[6], out + 8); put_unaligned_le32(inv_subshift(st1, 3) ^ rkp[7], out + 12); + + local_irq_restore(flags); }

static struct crypto_alg aes_alg = {

From: Andy Duan fugang.duan@nxp.com

[ Upstream commit 397bd9211fe014b347ca8f95a8f4e1017bac1aeb ]

Current driver only enable parity enable bit and never clear it when user set the termios. The fix clear the parity enable bit when PARENB flag is not set in termios->c_cflag.

Cc: Lukas Wunner lukas@wunner.de Signed-off-by: Andy Duan fugang.duan@nxp.com Reviewed-by: Fabio Estevam festevam@gmail.com Acked-by: Uwe Kleine-König u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/tty/serial/fsl_lpuart.c | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index 3f8d1274fc85..7d030c2e42ff 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -1477,6 +1477,8 @@ lpuart_set_termios(struct uart_port *port, struct ktermios *termios, else cr1 &= ~UARTCR1_PT; } + } else { + cr1 &= ~UARTCR1_PE; }

/* ask the core to calculate the divisor */ @@ -1688,6 +1690,8 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, else ctrl &= ~UARTCTRL_PT; } + } else { + ctrl &= ~UARTCTRL_PE; }

/* ask the core to calculate the divisor */

From: Miroslav Lichvar mlichvar@redhat.com

[ Upstream commit 83d0bdc7390b890905634186baaa294475cd6a06 ]

If a gettime64 call fails, return the error and avoid copying data back to user.

Cc: Richard Cochran richardcochran@gmail.com Cc: Jacob Keller jacob.e.keller@intel.com Signed-off-by: Miroslav Lichvar mlichvar@redhat.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/ptp/ptp_chardev.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/ptp/ptp_chardev.c b/drivers/ptp/ptp_chardev.c index 2012551d93e0..796eeffdf93b 100644 --- a/drivers/ptp/ptp_chardev.c +++ b/drivers/ptp/ptp_chardev.c @@ -228,7 +228,9 @@ long ptp_ioctl(struct posix_clock *pc, unsigned int cmd, unsigned long arg) pct->sec = ts.tv_sec; pct->nsec = ts.tv_nsec; pct++; - ptp->info->gettime64(ptp->info, &ts); + err = ptp->info->gettime64(ptp->info, &ts); + if (err) + goto out; pct->sec = ts.tv_sec; pct->nsec = ts.tv_nsec; pct++; @@ -281,6 +283,7 @@ long ptp_ioctl(struct posix_clock *pc, unsigned int cmd, unsigned long arg) break; }

+out: kfree(sysoff); return err; }

From: Ioana Ciornei ioana.ciornei@nxp.com

[ Upstream commit 5500598abbfb5b46201b9768bd9ea873a5eeaece ]

The fsl_mc_portal_allocate can fail when the requested MC portals are not yet probed by the fsl_mc_allocator. In this situation, the driver should defer the probe.

Signed-off-by: Ioana Ciornei ioana.ciornei@nxp.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/staging/fsl-dpaa2/rtc/rtc.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/staging/fsl-dpaa2/rtc/rtc.c b/drivers/staging/fsl-dpaa2/rtc/rtc.c index 0d52cb85441f..318a33c2f7a7 100644 --- a/drivers/staging/fsl-dpaa2/rtc/rtc.c +++ b/drivers/staging/fsl-dpaa2/rtc/rtc.c @@ -142,7 +142,10 @@ static int rtc_probe(struct fsl_mc_device *mc_dev)

err = fsl_mc_portal_allocate(mc_dev, 0, &mc_dev->mc_io); if (err) { - dev_err(dev, "fsl_mc_portal_allocate err %d\n", err); + if (err == -ENXIO) + err = -EPROBE_DEFER; + else + dev_err(dev, "fsl_mc_portal_allocate err %d\n", err); goto err_exit; }

From: Naftali Goldstein naftali.goldstein@intel.com

[ Upstream commit 5c2dbebb446539eb9640bf59a02756d6e7f1fc53 ]

If the association supports HE, HT/VHT rates will never be used for Tx and therefore there's no need to set the sgi-per-channel-width-support bits, so don't set them in this case.

Fixes: 110b32f065f3 ("iwlwifi: mvm: rs: add basic implementation of the new RS API handlers") Signed-off-by: Naftali Goldstein naftali.goldstein@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.c | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.c b/drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.c index 8169d1450b3b..d1c1a8069c7e 100644 --- a/drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.c +++ b/drivers/net/wireless/intel/iwlwifi/mvm/rs-fw.c @@ -98,8 +98,12 @@ static u8 rs_fw_sgi_cw_support(struct ieee80211_sta *sta) { struct ieee80211_sta_ht_cap *ht_cap = &sta->ht_cap; struct ieee80211_sta_vht_cap *vht_cap = &sta->vht_cap; + struct ieee80211_sta_he_cap *he_cap = &sta->he_cap; u8 supp = 0;

+ if (he_cap && he_cap->has_he) + return 0; + if (ht_cap->cap & IEEE80211_HT_CAP_SGI_20) supp |= BIT(IWL_TLC_MNG_CH_WIDTH_20MHZ); if (ht_cap->cap & IEEE80211_HT_CAP_SGI_40)

From: Andreas Puhm puhm@oregano.at

[ Upstream commit 68f60538daa4bc3da5d0764d46f391916fba20fd ]

The probe function needs to verify the CvP enable bit in order to properly determine if FPGA Manager functionality can be safely enabled.

Fixes: 34d1dc17ce97 ("fpga manager: Add Altera CvP driver") Signed-off-by: Andreas Puhm puhm@oregano.at Signed-off-by: Anatolij Gustschin agust@denx.de Reviewed-by: Moritz Fischer mdf@kernel.org Acked-by: Alan Tull atull@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/fpga/altera-cvp.c | 9 +++++++++ 1 file changed, 9 insertions(+)

diff --git a/drivers/fpga/altera-cvp.c b/drivers/fpga/altera-cvp.c index 68e4b2b98c8f..1f4c26b4794a 100644 --- a/drivers/fpga/altera-cvp.c +++ b/drivers/fpga/altera-cvp.c @@ -403,6 +403,7 @@ static int altera_cvp_probe(struct pci_dev *pdev, struct altera_cvp_conf *conf; struct fpga_manager *mgr; u16 cmd, val; + u32 regval; int ret;

/* @@ -416,6 +417,14 @@ static int altera_cvp_probe(struct pci_dev *pdev, return -ENODEV; }

+ pci_read_config_dword(pdev, VSE_CVP_STATUS, &regval); + if (!(regval & VSE_CVP_STATUS_CVP_EN)) { + dev_err(&pdev->dev, + "CVP is disabled for this device: CVP_STATUS Reg 0x%x\n", + regval); + return -ENODEV; + } + conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL); if (!conf) return -ENOMEM;

From: Anatolij Gustschin agust@denx.de

[ Upstream commit 187fade88ca0ff2df9d360ca751d948d73db7095 ]

If mapping the CvP BAR fails, we still can configure the FPGA via PCI config space access. In this case the iomap pointer is NULL. On x86_64, passing NULL address to pci_iounmap() generates "Bad IO access at port 0x0" output with stack call trace. Fix it.

Signed-off-by: Anatolij Gustschin agust@denx.de Acked-by: Alan Tull atull@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/fpga/altera-cvp.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/fpga/altera-cvp.c b/drivers/fpga/altera-cvp.c index 1f4c26b4794a..7a42c194b944 100644 --- a/drivers/fpga/altera-cvp.c +++ b/drivers/fpga/altera-cvp.c @@ -480,7 +480,8 @@ static int altera_cvp_probe(struct pci_dev *pdev, return 0;

err_unmap: - pci_iounmap(pdev, conf->map); + if (conf->map) + pci_iounmap(pdev, conf->map); pci_release_region(pdev, CVP_BAR); err_disable: cmd &= ~PCI_COMMAND_MEMORY; @@ -495,7 +496,8 @@ static void altera_cvp_remove(struct pci_dev *pdev) u16 cmd;

fpga_mgr_unregister(mgr); - pci_iounmap(pdev, conf->map); + if (conf->map) + pci_iounmap(pdev, conf->map); pci_release_region(pdev, CVP_BAR); pci_read_config_word(pdev, PCI_COMMAND, &cmd); cmd &= ~PCI_COMMAND_MEMORY;

From: Brian Norris briannorris@chromium.org

[ Upstream commit 6ad16b78a039b45294b1ad5d69c14ac57b2fe706 ]

EC_MKBP_EVENT_SENSOR_FIFO events can be triggered for a variety of reasons, and there are very few cases in which they should be treated as wakeup interrupts (particularly, when a certain MOTIONSENSE_MODULE_FLAG_* is set, but this is not even supported in the mainline cros_ec_sensor driver yet). Most of the time, they are benign sensor readings. In any case, the top-level cros_ec device doesn't know enough to determine that they should wake the system, and so it should not report the event. This would be the job of the cros_ec_sensors driver to parse.

This patch adds checks to cros_ec_get_next_event() such that it doesn't signal 'wakeup' for events of type EC_MKBP_EVENT_SENSOR_FIFO.

This patch is particularly relevant on devices like Scarlet (Rockchip RK3399 tablet, known as Acer Chromebook Tab 10), where the EC firmware reports sensor events much more frequently. This was causing /sys/power/wakeup_count to increase very frequently, often needlessly interrupting our ability to suspend the system.

Signed-off-by: Brian Norris briannorris@chromium.org Signed-off-by: Benson Leung bleung@chromium.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/platform/chrome/cros_ec_proto.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/platform/chrome/cros_ec_proto.c b/drivers/platform/chrome/cros_ec_proto.c index b6fd4838f60f..e5d5b1adb5a9 100644 --- a/drivers/platform/chrome/cros_ec_proto.c +++ b/drivers/platform/chrome/cros_ec_proto.c @@ -575,6 +575,7 @@ static int get_keyboard_state_event(struct cros_ec_device *ec_dev)

int cros_ec_get_next_event(struct cros_ec_device *ec_dev, bool *wake_event) { + u8 event_type; u32 host_event; int ret;

@@ -594,11 +595,22 @@ int cros_ec_get_next_event(struct cros_ec_device *ec_dev, bool *wake_event) return ret;

if (wake_event) { + event_type = ec_dev->event_data.event_type; host_event = cros_ec_get_host_event(ec_dev);

- /* Consider non-host_event as wake event */ - *wake_event = !host_event || - !!(host_event & ec_dev->host_event_wake_mask); + /* + * Sensor events need to be parsed by the sensor sub-device. + * Defer them, and don't report the wakeup here. + */ + if (event_type == EC_MKBP_EVENT_SENSOR_FIFO) + *wake_event = false; + /* Masked host-events should not count as wake events. */ + else if (host_event && + !(host_event & ec_dev->host_event_wake_mask)) + *wake_event = false; + /* Consider all other events as wake events. */ + else + *wake_event = true; }

return ret;

From: Xiang Chen chenxiang66@hisilicon.com

[ Upstream commit 15bc43f31a074076f114e0b87931e3b220b7bff1 ]

Currently the time of SAS SSP connection is 1ms, which means the link connection will fail if no IO response after this period.

For some disks handling large IO (such as 512k), 1ms is not enough, so change it to 5ms.

Signed-off-by: Xiang Chen chenxiang66@hisilicon.com Signed-off-by: John Garry john.garry@huawei.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c index 687ff61bba9f..3922b17e2ea3 100644 --- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c +++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c @@ -492,7 +492,7 @@ static void init_reg_v3_hw(struct hisi_hba *hisi_hba) hisi_sas_phy_write32(hisi_hba, i, PHYCTRL_OOB_RESTART_MSK, 0x1); hisi_sas_phy_write32(hisi_hba, i, STP_LINK_TIMER, 0x7f7a120); hisi_sas_phy_write32(hisi_hba, i, CON_CFG_DRIVER, 0x2a0a01); - + hisi_sas_phy_write32(hisi_hba, i, SAS_SSP_CON_TIMER_CFG, 0x32); /* used for 12G negotiate */ hisi_sas_phy_write32(hisi_hba, i, COARSETUNE_TIME, 0x1e); }

From: Ben Dooks ben.dooks@codethink.co.uk

[ Upstream commit 810eeb1f41a9a272eedc94ca18c072e75678ede4 ]

The smsc95xx driver already takes into account the NET_IP_ALIGN parameter when setting up the receive packet data, which means we do not need to worry about aligning the packets in the usbnet driver.

Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now passed to the ip_rcv() routine with the start on an aligned address.

Tested on Raspberry Pi B3.

Signed-off-by: Ben Dooks ben.dooks@codethink.co.uk Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/smsc95xx.c | 1 + 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c index f2d01cb6f958..6e971628bb50 100644 --- a/drivers/net/usb/smsc95xx.c +++ b/drivers/net/usb/smsc95xx.c @@ -1295,6 +1295,7 @@ static int smsc95xx_bind(struct usbnet *dev, struct usb_interface *intf) dev->net->features |= NETIF_F_RXCSUM;

dev->net->hw_features = NETIF_F_IP_CSUM | NETIF_F_RXCSUM; + set_bit(EVENT_NO_IP_ALIGN, &dev->flags);

smsc95xx_init_mac_address(dev);

From: Nathan Chancellor natechancellor@gmail.com

[ Upstream commit c10b26abeb53cabc1e6271a167d3f3d396ce0218 ]

When building the kernel with Clang, the following section mismatch warnings appears:

WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from the function _setup() to the function .init.text:_setup_iclk_autoidle() The function _setup() references the function __init _setup_iclk_autoidle(). This is often because _setup lacks a __init annotation or the annotation of _setup_iclk_autoidle is wrong.

WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from the function _setup() to the function .init.text:_setup_reset() The function _setup() references the function __init _setup_reset(). This is often because _setup lacks a __init annotation or the annotation of _setup_reset is wrong.

WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from the function _setup() to the function .init.text:_setup_postsetup() The function _setup() references the function __init _setup_postsetup(). This is often because _setup lacks a __init annotation or the annotation of _setup_postsetup is wrong.

_setup is used in omap_hwmod_allocate_module, which isn't marked __init and looks like it shouldn't be, meaning to fix these warnings, those functions must be moved out of the init section, which this patch does.

Signed-off-by: Nathan Chancellor natechancellor@gmail.com Signed-off-by: Tony Lindgren tony@atomide.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-omap2/omap_hwmod.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index cd65ea4e9c54..ec3789ba17b8 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -2397,7 +2397,7 @@ static int __init _init(struct omap_hwmod *oh, void *data) * a stub; implementing this properly requires iclk autoidle usecounting in * the clock code. No return value. */ -static void __init _setup_iclk_autoidle(struct omap_hwmod *oh) +static void _setup_iclk_autoidle(struct omap_hwmod *oh) { struct omap_hwmod_ocp_if *os;

@@ -2428,7 +2428,7 @@ static void __init _setup_iclk_autoidle(struct omap_hwmod *oh) * reset. Returns 0 upon success or a negative error code upon * failure. */ -static int __init _setup_reset(struct omap_hwmod *oh) +static int _setup_reset(struct omap_hwmod *oh) { int r;

@@ -2489,7 +2489,7 @@ static int __init _setup_reset(struct omap_hwmod *oh) * * No return value. */ -static void __init _setup_postsetup(struct omap_hwmod *oh) +static void _setup_postsetup(struct omap_hwmod *oh) { u8 postsetup_state;

From: Yogesh Mohan Marimuthu yogesh.mohanmarimuthu@amd.com

[ Upstream commit 08e1c28dd521c7b08d1b0af0bae9fb22ccc012a4 ]

[why] phy_pix_clk is one of the variable used to check if one PLL can be shared with displays having common mode set configuration. As of now phy_pix_clock varialbe is calculated in function dc_validate_stream(). dc_validate_stream() function is called after clocks are assigned for the new display. Due to this during hotplug, when PLL sharing conditions are checked for new display phy_pix_clk variable will be 0 and for displays that are already enabled phy_pix_clk will have some value. Hence PLL will not be shared and if the display hardware doesn't have any more PLL to assign, mode set will fail due to resource unavailability.

[how] Instead of only calculating the phy_pix_clk variable after the PLL is assigned for new display, this patch calculates phy_pix_clk also during the before assigning the PLL for new display.

Signed-off-by: Yogesh Mohan Marimuthu yogesh.mohanmarimuthu@amd.com Reviewed-by: Harry Wentland Harry.Wentland@amd.com Acked-by: Bhawanpreet Lakha Bhawanpreet.Lakha@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/display/dc/core/dc_resource.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/amd/display/dc/core/dc_resource.c b/drivers/gpu/drm/amd/display/dc/core/dc_resource.c index ea6beccfd89d..87bf422f16be 100644 --- a/drivers/gpu/drm/amd/display/dc/core/dc_resource.c +++ b/drivers/gpu/drm/amd/display/dc/core/dc_resource.c @@ -1917,6 +1917,8 @@ enum dc_status resource_map_pool_resources( } */

+ calculate_phy_pix_clks(stream); + /* acquire new resources */ pipe_idx = acquire_first_free_pipe(&context->res_ctx, pool, stream);

From: Saeed Mahameed saeedm@mellanox.com

[ Upstream commit 1e86ace4c140fd5a693e266c9b23409358f25381 ]

Currently the cpu affinity hint mask for completion EQs is stored and read from the wrong place, since reading and storing is done from the same index, there is no actual issue with that, but internal irq_info for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info array, this patch changes the code to use the correct offset to store and read the IRQ affinity hint.

Signed-off-by: Saeed Mahameed saeedm@mellanox.com Reviewed-by: Leon Romanovsky leonro@mellanox.com Reviewed-by: Tariq Toukan tariqt@mellanox.com Signed-off-by: Leon Romanovsky leonro@mellanox.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 2 +- drivers/net/ethernet/mellanox/mlx5/core/main.c | 14 ++++++++------ include/linux/mlx5/driver.h | 2 +- 3 files changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c index 7365899c3ac9..944f21f99d43 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c @@ -1758,7 +1758,7 @@ static void mlx5e_close_cq(struct mlx5e_cq *cq)

static int mlx5e_get_cpu(struct mlx5e_priv *priv, int ix) { - return cpumask_first(priv->mdev->priv.irq_info[ix].mask); + return cpumask_first(priv->mdev->priv.irq_info[ix + MLX5_EQ_VEC_COMP_BASE].mask); }

static int mlx5e_open_tx_cqs(struct mlx5e_channel *c, diff --git a/drivers/net/ethernet/mellanox/mlx5/core/main.c b/drivers/net/ethernet/mellanox/mlx5/core/main.c index b5e9f664fc66..563ce3fedab4 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/main.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c @@ -640,18 +640,19 @@ u64 mlx5_read_internal_timer(struct mlx5_core_dev *dev) static int mlx5_irq_set_affinity_hint(struct mlx5_core_dev *mdev, int i) { struct mlx5_priv *priv = &mdev->priv; - int irq = pci_irq_vector(mdev->pdev, MLX5_EQ_VEC_COMP_BASE + i); + int vecidx = MLX5_EQ_VEC_COMP_BASE + i; + int irq = pci_irq_vector(mdev->pdev, vecidx);

- if (!zalloc_cpumask_var(&priv->irq_info[i].mask, GFP_KERNEL)) { + if (!zalloc_cpumask_var(&priv->irq_info[vecidx].mask, GFP_KERNEL)) { mlx5_core_warn(mdev, "zalloc_cpumask_var failed"); return -ENOMEM; }

cpumask_set_cpu(cpumask_local_spread(i, priv->numa_node), - priv->irq_info[i].mask); + priv->irq_info[vecidx].mask);

if (IS_ENABLED(CONFIG_SMP) && - irq_set_affinity_hint(irq, priv->irq_info[i].mask)) + irq_set_affinity_hint(irq, priv->irq_info[vecidx].mask)) mlx5_core_warn(mdev, "irq_set_affinity_hint failed, irq 0x%.4x", irq);

return 0; @@ -659,11 +660,12 @@ static int mlx5_irq_set_affinity_hint(struct mlx5_core_dev *mdev, int i)

static void mlx5_irq_clear_affinity_hint(struct mlx5_core_dev *mdev, int i) { + int vecidx = MLX5_EQ_VEC_COMP_BASE + i; struct mlx5_priv *priv = &mdev->priv; - int irq = pci_irq_vector(mdev->pdev, MLX5_EQ_VEC_COMP_BASE + i); + int irq = pci_irq_vector(mdev->pdev, vecidx);

irq_set_affinity_hint(irq, NULL); - free_cpumask_var(priv->irq_info[i].mask); + free_cpumask_var(priv->irq_info[vecidx].mask); }

static int mlx5_irq_set_affinity_hints(struct mlx5_core_dev *mdev) diff --git a/include/linux/mlx5/driver.h b/include/linux/mlx5/driver.h index 88a041b73abf..bbcfe2e5fd91 100644 --- a/include/linux/mlx5/driver.h +++ b/include/linux/mlx5/driver.h @@ -1321,7 +1321,7 @@ enum { static inline const struct cpumask * mlx5_get_vector_affinity_hint(struct mlx5_core_dev *dev, int vector) { - return dev->priv.irq_info[vector].mask; + return dev->priv.irq_info[vector + MLX5_EQ_VEC_COMP_BASE].mask; }

#endif /* MLX5_DRIVER_H */

From: Pu Wen puwen@hygon.cn

[ Upstream commit 4787eff3fa88f62fede6ed7afa06477ae6bf984d ]

The tool perf is useful for the performance analysis on the Hygon Dhyana platform. But right now there is no Hygon support for it to analyze the KVM guest os data. So add Hygon Dhyana support to it by checking vendor string to share the code path of AMD.

Signed-off-by: Pu Wen puwen@hygon.cn Acked-by: Borislav Petkov bp@suse.de Cc: Alexander Shishkin alexander.shishkin@linux.intel.com Cc: Jiri Olsa jolsa@kernel.org Cc: Namhyung Kim namhyung@kernel.org Cc: Peter Zijlstra peterz@infradead.org Cc: Thomas Gleixner tglx@linutronix.de Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn Signed-off-by: Arnaldo Carvalho de Melo acme@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- tools/perf/arch/x86/util/kvm-stat.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/perf/arch/x86/util/kvm-stat.c b/tools/perf/arch/x86/util/kvm-stat.c index b32409a0e546..081353d7b095 100644 --- a/tools/perf/arch/x86/util/kvm-stat.c +++ b/tools/perf/arch/x86/util/kvm-stat.c @@ -156,7 +156,7 @@ int cpu_isa_init(struct perf_kvm_stat *kvm, const char *cpuid) if (strstr(cpuid, "Intel")) { kvm->exit_reasons = vmx_exit_reasons; kvm->exit_reasons_isa = "VMX"; - } else if (strstr(cpuid, "AMD")) { + } else if (strstr(cpuid, "AMD") || strstr(cpuid, "Hygon")) { kvm->exit_reasons = svm_exit_reasons; kvm->exit_reasons_isa = "SVM"; } else

From: Sean Young sean@mess.org

[ Upstream commit 8e782fcf78275f505194e767c515202d4fd274bc ]

If userspace has an open file descriptor on the rc input device or lirc device when rc_unregister_device() is called, then the rc close() is never called.

This ensures that the receiver is turned off on the nuvoton-cir driver during shutdown.

Signed-off-by: Sean Young sean@mess.org Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/rc/rc-main.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/media/rc/rc-main.c b/drivers/media/rc/rc-main.c index 8b2c16dd58bd..0f218afdadaa 100644 --- a/drivers/media/rc/rc-main.c +++ b/drivers/media/rc/rc-main.c @@ -1956,6 +1956,8 @@ void rc_unregister_device(struct rc_dev *dev) rc_free_rx_device(dev);

mutex_lock(&dev->lock); + if (dev->users && dev->close) + dev->close(dev); dev->registered = false; mutex_unlock(&dev->lock);

From: Alexey Khoroshilov khoroshilov@ispras.ru

[ Upstream commit 8ea0f2ba0fa3f91ea1b8d823a54b042026ada6b3 ]

of_parse_phandle() returns the device node with refcount incremented. There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(), but their refcounts are not decremented.

The patch adds one of_node_put() and fixes returning error codes.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov khoroshilov@ispras.ru Signed-off-by: Hans Verkuil hverkuil@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_pm.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_pm.c b/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_pm.c index 3e73e9db781f..7c025045ea90 100644 --- a/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_pm.c +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_pm.c @@ -41,25 +41,27 @@ int mtk_vcodec_init_enc_pm(struct mtk_vcodec_dev *mtkdev) node = of_parse_phandle(dev->of_node, "mediatek,larb", 0); if (!node) { mtk_v4l2_err("no mediatek,larb found"); - return -1; + return -ENODEV; } pdev = of_find_device_by_node(node); + of_node_put(node); if (!pdev) { mtk_v4l2_err("no mediatek,larb device found"); - return -1; + return -ENODEV; } pm->larbvenc = &pdev->dev;

node = of_parse_phandle(dev->of_node, "mediatek,larb", 1); if (!node) { mtk_v4l2_err("no mediatek,larb found"); - return -1; + return -ENODEV; }

pdev = of_find_device_by_node(node); + of_node_put(node); if (!pdev) { mtk_v4l2_err("no mediatek,larb device found"); - return -1; + return -ENODEV; }

pm->larbvenclt = &pdev->dev;

From: Babu Moger Babu.Moger@amd.com

[ Upstream commit 723f1a0dd8e26a7523ba068204bee11c95ded38d ]

Fix the messages in rdt_last_cmd_printf() and rdt_last_cmd_puts() to make them more meaningful and consistent.

[ bp: s/cpu/CPU/; s/mem\W/memory ]

Signed-off-by: Babu Moger babu.moger@amd.com Signed-off-by: Borislav Petkov bp@suse.de Cc: Andrew Morton akpm@linux-foundation.org Cc: Andy Lutomirski luto@kernel.org Cc: Arnd Bergmann arnd@arndb.de Cc: Brijesh Singh brijesh.singh@amd.com Cc: "Chang S. Bae" chang.seok.bae@intel.com Cc: David Miller davem@davemloft.net Cc: David Woodhouse dwmw2@infradead.org Cc: Dmitry Safonov dima@arista.com Cc: Fenghua Yu fenghua.yu@intel.com Cc: Greg Kroah-Hartman gregkh@linuxfoundation.org Cc: "H. Peter Anvin" hpa@zytor.com Cc: Ingo Molnar mingo@redhat.com Cc: Jann Horn jannh@google.com Cc: Joerg Roedel jroedel@suse.de Cc: Jonathan Corbet corbet@lwn.net Cc: Josh Poimboeuf jpoimboe@redhat.com Cc: Kate Stewart kstewart@linuxfoundation.org Cc: "Kirill A. Shutemov" kirill.shutemov@linux.intel.com Cc: linux-doc@vger.kernel.org Cc: Mauro Carvalho Chehab mchehab+samsung@kernel.org Cc: Paolo Bonzini pbonzini@redhat.com Cc: Peter Zijlstra peterz@infradead.org Cc: Philippe Ombredanne pombredanne@nexb.com Cc: Pu Wen puwen@hygon.cn Cc: qianyue.zj@alibaba-inc.com Cc: "Rafael J. Wysocki" rafael@kernel.org Cc: Reinette Chatre reinette.chatre@intel.com Cc: Rian Hunter rian@alum.mit.edu Cc: Sherry Hurwitz sherry.hurwitz@amd.com Cc: Suravee Suthikulpanit suravee.suthikulpanit@amd.com Cc: Thomas Gleixner tglx@linutronix.de Cc: Thomas Lendacky Thomas.Lendacky@amd.com Cc: Tony Luck tony.luck@intel.com Cc: Vitaly Kuznetsov vkuznets@redhat.com Cc: xiaochen.shen@intel.com Link: https://lkml.kernel.org/r/20181121202811.4492-11-babu.moger@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/x86/kernel/cpu/intel_rdt_ctrlmondata.c | 22 ++++++------- arch/x86/kernel/cpu/intel_rdt_pseudo_lock.c | 34 +++++++++---------- arch/x86/kernel/cpu/intel_rdt_rdtgroup.c | 36 ++++++++++----------- 3 files changed, 46 insertions(+), 46 deletions(-)

diff --git a/arch/x86/kernel/cpu/intel_rdt_ctrlmondata.c b/arch/x86/kernel/cpu/intel_rdt_ctrlmondata.c index 627e5c809b33..79d099538f2e 100644 --- a/arch/x86/kernel/cpu/intel_rdt_ctrlmondata.c +++ b/arch/x86/kernel/cpu/intel_rdt_ctrlmondata.c @@ -71,7 +71,7 @@ int parse_bw(struct rdt_parse_data *data, struct rdt_resource *r, unsigned long bw_val;

if (d->have_new_ctrl) { - rdt_last_cmd_printf("duplicate domain %d\n", d->id); + rdt_last_cmd_printf("Duplicate domain %d\n", d->id); return -EINVAL; }

@@ -97,12 +97,12 @@ static bool cbm_validate(char *buf, u32 *data, struct rdt_resource *r)

ret = kstrtoul(buf, 16, &val); if (ret) { - rdt_last_cmd_printf("non-hex character in mask %s\n", buf); + rdt_last_cmd_printf("Non-hex character in the mask %s\n", buf); return false; }

if (val == 0 || val > r->default_ctrl) { - rdt_last_cmd_puts("mask out of range\n"); + rdt_last_cmd_puts("Mask out of range\n"); return false; }

@@ -110,12 +110,12 @@ static bool cbm_validate(char *buf, u32 *data, struct rdt_resource *r) zero_bit = find_next_zero_bit(&val, cbm_len, first_bit);

if (find_next_bit(&val, cbm_len, zero_bit) < cbm_len) { - rdt_last_cmd_printf("mask %lx has non-consecutive 1-bits\n", val); + rdt_last_cmd_printf("The mask %lx has non-consecutive 1-bits\n", val); return false; }

if ((zero_bit - first_bit) < r->cache.min_cbm_bits) { - rdt_last_cmd_printf("Need at least %d bits in mask\n", + rdt_last_cmd_printf("Need at least %d bits in the mask\n", r->cache.min_cbm_bits); return false; } @@ -135,7 +135,7 @@ int parse_cbm(struct rdt_parse_data *data, struct rdt_resource *r, u32 cbm_val;

if (d->have_new_ctrl) { - rdt_last_cmd_printf("duplicate domain %d\n", d->id); + rdt_last_cmd_printf("Duplicate domain %d\n", d->id); return -EINVAL; }

@@ -145,7 +145,7 @@ int parse_cbm(struct rdt_parse_data *data, struct rdt_resource *r, */ if (rdtgrp->mode == RDT_MODE_PSEUDO_LOCKSETUP && rdtgroup_pseudo_locked_in_hierarchy(d)) { - rdt_last_cmd_printf("pseudo-locked region in hierarchy\n"); + rdt_last_cmd_printf("Pseudo-locked region in hierarchy\n"); return -EINVAL; }

@@ -164,14 +164,14 @@ int parse_cbm(struct rdt_parse_data *data, struct rdt_resource *r, * either is exclusive. */ if (rdtgroup_cbm_overlaps(r, d, cbm_val, rdtgrp->closid, true)) { - rdt_last_cmd_printf("overlaps with exclusive group\n"); + rdt_last_cmd_printf("Overlaps with exclusive group\n"); return -EINVAL; }

if (rdtgroup_cbm_overlaps(r, d, cbm_val, rdtgrp->closid, false)) { if (rdtgrp->mode == RDT_MODE_EXCLUSIVE || rdtgrp->mode == RDT_MODE_PSEUDO_LOCKSETUP) { - rdt_last_cmd_printf("overlaps with other group\n"); + rdt_last_cmd_printf("0verlaps with other group\n"); return -EINVAL; } } @@ -293,7 +293,7 @@ static int rdtgroup_parse_resource(char *resname, char *tok, if (!strcmp(resname, r->name) && rdtgrp->closid < r->num_closid) return parse_line(tok, r, rdtgrp); } - rdt_last_cmd_printf("unknown/unsupported resource name '%s'\n", resname); + rdt_last_cmd_printf("Unknown or unsupported resource name '%s'\n", resname); return -EINVAL; }

@@ -326,7 +326,7 @@ ssize_t rdtgroup_schemata_write(struct kernfs_open_file *of, */ if (rdtgrp->mode == RDT_MODE_PSEUDO_LOCKED) { ret = -EINVAL; - rdt_last_cmd_puts("resource group is pseudo-locked\n"); + rdt_last_cmd_puts("Resource group is pseudo-locked\n"); goto out; }

diff --git a/arch/x86/kernel/cpu/intel_rdt_pseudo_lock.c b/arch/x86/kernel/cpu/intel_rdt_pseudo_lock.c index f8c260d522ca..caa680fb5680 100644 --- a/arch/x86/kernel/cpu/intel_rdt_pseudo_lock.c +++ b/arch/x86/kernel/cpu/intel_rdt_pseudo_lock.c @@ -221,7 +221,7 @@ static int pseudo_lock_cstates_constrain(struct pseudo_lock_region *plr) for_each_cpu(cpu, &plr->d->cpu_mask) { pm_req = kzalloc(sizeof(*pm_req), GFP_KERNEL); if (!pm_req) { - rdt_last_cmd_puts("fail allocating mem for PM QoS\n"); + rdt_last_cmd_puts("Failure to allocate memory for PM QoS\n"); ret = -ENOMEM; goto out_err; } @@ -230,7 +230,7 @@ static int pseudo_lock_cstates_constrain(struct pseudo_lock_region *plr) DEV_PM_QOS_RESUME_LATENCY, 30); if (ret < 0) { - rdt_last_cmd_printf("fail to add latency req cpu%d\n", + rdt_last_cmd_printf("Failed to add latency req CPU%d\n", cpu); kfree(pm_req); ret = -1; @@ -297,7 +297,7 @@ static int pseudo_lock_region_init(struct pseudo_lock_region *plr) plr->cpu = cpumask_first(&plr->d->cpu_mask);

if (!cpu_online(plr->cpu)) { - rdt_last_cmd_printf("cpu %u associated with cache not online\n", + rdt_last_cmd_printf("CPU %u associated with cache not online\n", plr->cpu); ret = -ENODEV; goto out_region; @@ -315,7 +315,7 @@ static int pseudo_lock_region_init(struct pseudo_lock_region *plr) }

ret = -1; - rdt_last_cmd_puts("unable to determine cache line size\n"); + rdt_last_cmd_puts("Unable to determine cache line size\n"); out_region: pseudo_lock_region_clear(plr); return ret; @@ -369,14 +369,14 @@ static int pseudo_lock_region_alloc(struct pseudo_lock_region *plr) * KMALLOC_MAX_SIZE. */ if (plr->size > KMALLOC_MAX_SIZE) { - rdt_last_cmd_puts("requested region exceeds maximum size\n"); + rdt_last_cmd_puts("Requested region exceeds maximum size\n"); ret = -E2BIG; goto out_region; }

plr->kmem = kzalloc(plr->size, GFP_KERNEL); if (!plr->kmem) { - rdt_last_cmd_puts("unable to allocate memory\n"); + rdt_last_cmd_puts("Unable to allocate memory\n"); ret = -ENOMEM; goto out_region; } @@ -673,7 +673,7 @@ int rdtgroup_locksetup_enter(struct rdtgroup *rdtgrp) * default closid associated with it. */ if (rdtgrp == &rdtgroup_default) { - rdt_last_cmd_puts("cannot pseudo-lock default group\n"); + rdt_last_cmd_puts("Cannot pseudo-lock default group\n"); return -EINVAL; }

@@ -715,17 +715,17 @@ int rdtgroup_locksetup_enter(struct rdtgroup *rdtgrp) */ prefetch_disable_bits = get_prefetch_disable_bits(); if (prefetch_disable_bits == 0) { - rdt_last_cmd_puts("pseudo-locking not supported\n"); + rdt_last_cmd_puts("Pseudo-locking not supported\n"); return -EINVAL; }

if (rdtgroup_monitor_in_progress(rdtgrp)) { - rdt_last_cmd_puts("monitoring in progress\n"); + rdt_last_cmd_puts("Monitoring in progress\n"); return -EINVAL; }

if (rdtgroup_tasks_assigned(rdtgrp)) { - rdt_last_cmd_puts("tasks assigned to resource group\n"); + rdt_last_cmd_puts("Tasks assigned to resource group\n"); return -EINVAL; }

@@ -735,13 +735,13 @@ int rdtgroup_locksetup_enter(struct rdtgroup *rdtgrp) }

if (rdtgroup_locksetup_user_restrict(rdtgrp)) { - rdt_last_cmd_puts("unable to modify resctrl permissions\n"); + rdt_last_cmd_puts("Unable to modify resctrl permissions\n"); return -EIO; }

ret = pseudo_lock_init(rdtgrp); if (ret) { - rdt_last_cmd_puts("unable to init pseudo-lock region\n"); + rdt_last_cmd_puts("Unable to init pseudo-lock region\n"); goto out_release; }

@@ -778,7 +778,7 @@ int rdtgroup_locksetup_exit(struct rdtgroup *rdtgrp) if (rdt_mon_capable) { ret = alloc_rmid(); if (ret < 0) { - rdt_last_cmd_puts("out of RMIDs\n"); + rdt_last_cmd_puts("Out of RMIDs\n"); return ret; } rdtgrp->mon.rmid = ret; @@ -1234,7 +1234,7 @@ int rdtgroup_pseudo_lock_create(struct rdtgroup *rdtgrp) "pseudo_lock/%u", plr->cpu); if (IS_ERR(thread)) { ret = PTR_ERR(thread); - rdt_last_cmd_printf("locking thread returned error %d\n", ret); + rdt_last_cmd_printf("Locking thread returned error %d\n", ret); goto out_cstates; }

@@ -1252,13 +1252,13 @@ int rdtgroup_pseudo_lock_create(struct rdtgroup *rdtgrp) * the cleared, but not freed, plr struct resulting in an * empty pseudo-locking loop. */ - rdt_last_cmd_puts("locking thread interrupted\n"); + rdt_last_cmd_puts("Locking thread interrupted\n"); goto out_cstates; }

ret = pseudo_lock_minor_get(&new_minor); if (ret < 0) { - rdt_last_cmd_puts("unable to obtain a new minor number\n"); + rdt_last_cmd_puts("Unable to obtain a new minor number\n"); goto out_cstates; }

@@ -1290,7 +1290,7 @@ int rdtgroup_pseudo_lock_create(struct rdtgroup *rdtgrp)

if (IS_ERR(dev)) { ret = PTR_ERR(dev); - rdt_last_cmd_printf("failed to create character device: %d\n", + rdt_last_cmd_printf("Failed to create character device: %d\n", ret); goto out_debugfs; } diff --git a/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c b/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c index 643670fb8943..49ebefde9349 100644 --- a/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c +++ b/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c @@ -335,7 +335,7 @@ static int cpus_mon_write(struct rdtgroup *rdtgrp, cpumask_var_t newmask, /* Check whether cpus belong to parent ctrl group */ cpumask_andnot(tmpmask, newmask, &prgrp->cpu_mask); if (cpumask_weight(tmpmask)) { - rdt_last_cmd_puts("can only add CPUs to mongroup that belong to parent\n"); + rdt_last_cmd_puts("Can only add CPUs to mongroup that belong to parent\n"); return -EINVAL; }

@@ -460,14 +460,14 @@ static ssize_t rdtgroup_cpus_write(struct kernfs_open_file *of, rdt_last_cmd_clear(); if (!rdtgrp) { ret = -ENOENT; - rdt_last_cmd_puts("directory was removed\n"); + rdt_last_cmd_puts("Directory was removed\n"); goto unlock; }

if (rdtgrp->mode == RDT_MODE_PSEUDO_LOCKED || rdtgrp->mode == RDT_MODE_PSEUDO_LOCKSETUP) { ret = -EINVAL; - rdt_last_cmd_puts("pseudo-locking in progress\n"); + rdt_last_cmd_puts("Pseudo-locking in progress\n"); goto unlock; }

@@ -477,7 +477,7 @@ static ssize_t rdtgroup_cpus_write(struct kernfs_open_file *of, ret = cpumask_parse(buf, newmask);

if (ret) { - rdt_last_cmd_puts("bad cpu list/mask\n"); + rdt_last_cmd_puts("Bad CPU list/mask\n"); goto unlock; }

@@ -485,7 +485,7 @@ static ssize_t rdtgroup_cpus_write(struct kernfs_open_file *of, cpumask_andnot(tmpmask, newmask, cpu_online_mask); if (cpumask_weight(tmpmask)) { ret = -EINVAL; - rdt_last_cmd_puts("can only assign online cpus\n"); + rdt_last_cmd_puts("Can only assign online CPUs\n"); goto unlock; }

@@ -564,7 +564,7 @@ static int __rdtgroup_move_task(struct task_struct *tsk, */ atomic_dec(&rdtgrp->waitcount); kfree(callback); - rdt_last_cmd_puts("task exited\n"); + rdt_last_cmd_puts("Task exited\n"); } else { /* * For ctrl_mon groups move both closid and rmid. @@ -682,7 +682,7 @@ static ssize_t rdtgroup_tasks_write(struct kernfs_open_file *of, if (rdtgrp->mode == RDT_MODE_PSEUDO_LOCKED || rdtgrp->mode == RDT_MODE_PSEUDO_LOCKSETUP) { ret = -EINVAL; - rdt_last_cmd_puts("pseudo-locking in progress\n"); + rdt_last_cmd_puts("Pseudo-locking in progress\n"); goto unlock; }

@@ -1042,14 +1042,14 @@ static bool rdtgroup_mode_test_exclusive(struct rdtgroup *rdtgrp) list_for_each_entry(d, &r->domains, list) { if (rdtgroup_cbm_overlaps(r, d, d->ctrl_val[closid], rdtgrp->closid, false)) { - rdt_last_cmd_puts("schemata overlaps\n"); + rdt_last_cmd_puts("Schemata overlaps\n"); return false; } } }

if (!has_cache) { - rdt_last_cmd_puts("cannot be exclusive without CAT/CDP\n"); + rdt_last_cmd_puts("Cannot be exclusive without CAT/CDP\n"); return false; }

@@ -1090,7 +1090,7 @@ static ssize_t rdtgroup_mode_write(struct kernfs_open_file *of, goto out;

if (mode == RDT_MODE_PSEUDO_LOCKED) { - rdt_last_cmd_printf("cannot change pseudo-locked group\n"); + rdt_last_cmd_printf("Cannot change pseudo-locked group\n"); ret = -EINVAL; goto out; } @@ -1119,7 +1119,7 @@ static ssize_t rdtgroup_mode_write(struct kernfs_open_file *of, goto out; rdtgrp->mode = RDT_MODE_PSEUDO_LOCKSETUP; } else { - rdt_last_cmd_printf("unknown/unsupported mode\n"); + rdt_last_cmd_printf("Unknown orunsupported mode\n"); ret = -EINVAL; }

@@ -2403,7 +2403,7 @@ static int rdtgroup_init_alloc(struct rdtgroup *rdtgrp) tmp_cbm = d->new_ctrl; if (bitmap_weight(&tmp_cbm, r->cache.cbm_len) < r->cache.min_cbm_bits) { - rdt_last_cmd_printf("no space on %s:%d\n", + rdt_last_cmd_printf("No space on %s:%d\n", r->name, d->id); return -ENOSPC; } @@ -2420,7 +2420,7 @@ static int rdtgroup_init_alloc(struct rdtgroup *rdtgrp) continue; ret = update_domains(r, rdtgrp->closid); if (ret < 0) { - rdt_last_cmd_puts("failed to initialize allocations\n"); + rdt_last_cmd_puts("Failed to initialize allocations\n"); return ret; } rdtgrp->mode = RDT_MODE_SHAREABLE; @@ -2443,7 +2443,7 @@ static int mkdir_rdt_prepare(struct kernfs_node *parent_kn, rdt_last_cmd_clear(); if (!prdtgrp) { ret = -ENODEV; - rdt_last_cmd_puts("directory was removed\n"); + rdt_last_cmd_puts("Directory was removed\n"); goto out_unlock; }

@@ -2451,7 +2451,7 @@ static int mkdir_rdt_prepare(struct kernfs_node *parent_kn, (prdtgrp->mode == RDT_MODE_PSEUDO_LOCKSETUP || prdtgrp->mode == RDT_MODE_PSEUDO_LOCKED)) { ret = -EINVAL; - rdt_last_cmd_puts("pseudo-locking in progress\n"); + rdt_last_cmd_puts("Pseudo-locking in progress\n"); goto out_unlock; }

@@ -2459,7 +2459,7 @@ static int mkdir_rdt_prepare(struct kernfs_node *parent_kn, rdtgrp = kzalloc(sizeof(*rdtgrp), GFP_KERNEL); if (!rdtgrp) { ret = -ENOSPC; - rdt_last_cmd_puts("kernel out of memory\n"); + rdt_last_cmd_puts("Kernel out of memory\n"); goto out_unlock; } *r = rdtgrp; @@ -2500,7 +2500,7 @@ static int mkdir_rdt_prepare(struct kernfs_node *parent_kn, if (rdt_mon_capable) { ret = alloc_rmid(); if (ret < 0) { - rdt_last_cmd_puts("out of RMIDs\n"); + rdt_last_cmd_puts("Out of RMIDs\n"); goto out_destroy; } rdtgrp->mon.rmid = ret; @@ -2588,7 +2588,7 @@ static int rdtgroup_mkdir_ctrl_mon(struct kernfs_node *parent_kn, kn = rdtgrp->kn; ret = closid_alloc(); if (ret < 0) { - rdt_last_cmd_puts("out of CLOSIDs\n"); + rdt_last_cmd_puts("Out of CLOSIDs\n"); goto out_common_fail; } closid = ret;

From: Martin Blumenstingl martin.blumenstingl@googlemail.com

[ Upstream commit a8662eadd1032018f31e37deda811790b2326662 ]

According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is the register for the CPU scale_div clock. This matches the code in Amlogic's 3.10 GPL kernel sources: N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;

This means that the divider register is 10 bit wide instead of 9 bits. So far this is not a problem since all u-boot versions I have seen are not using the cpu_scale_div clock at all (instead they are configuring the CPU clock to run off cpu_in_sel directly).

The fixes tag points to the latest rework of the CPU clocks. However, even before the rework it was wrong. Commit 7a29a869434e8b ("clk: meson: Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation this only carries the fixes tag for the CPU clock rewordk.

Fixes: 251b6fd38bcb9c ("clk: meson: rework meson8b cpu clock") Signed-off-by: Martin Blumenstingl martin.blumenstingl@googlemail.com Signed-off-by: Neil Armstrong narmstrong@baylibre.com Link: https://lkml.kernel.org/r/20180927085921.24627-3-martin.blumenstingl@googlem... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/meson/meson8b.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/meson/meson8b.c b/drivers/clk/meson/meson8b.c index 580a86d120e8..0da8334f2e43 100644 --- a/drivers/clk/meson/meson8b.c +++ b/drivers/clk/meson/meson8b.c @@ -583,7 +583,7 @@ static struct clk_regmap meson8b_cpu_scale_div = { .data = &(struct clk_regmap_div_data){ .offset = HHI_SYS_CPU_CLK_CNTL1, .shift = 20, - .width = 9, + .width = 10, .table = cpu_scale_table, .flags = CLK_DIVIDER_ALLOW_ZERO, },

From: YueHaibing yuehaibing@huawei.com

[ Upstream commit aea0a897af9e44c258e8ab9296fad417f1bc063a ]

Fix smatch warning:

drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn: passing zero to 'ERR_PTR'

'err' should be set while device_create_with_groups and pps_register_source fails

Fixes: 85a66e550195 ("ptp: create "pins" together with the rest of attributes") Signed-off-by: YueHaibing yuehaibing@huawei.com Acked-by: Richard Cochran richardcochran@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/ptp/ptp_clock.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/ptp/ptp_clock.c b/drivers/ptp/ptp_clock.c index 7eacc1c4b3b1..c64903a5978f 100644 --- a/drivers/ptp/ptp_clock.c +++ b/drivers/ptp/ptp_clock.c @@ -253,8 +253,10 @@ struct ptp_clock *ptp_clock_register(struct ptp_clock_info *info, ptp->dev = device_create_with_groups(ptp_class, parent, ptp->devid, ptp, ptp->pin_attr_groups, "ptp%d", ptp->index); - if (IS_ERR(ptp->dev)) + if (IS_ERR(ptp->dev)) { + err = PTR_ERR(ptp->dev); goto no_device; + }

/* Register a new PPS source. */ if (info->pps) { @@ -265,6 +267,7 @@ struct ptp_clock *ptp_clock_register(struct ptp_clock_info *info, pps.owner = info->owner; ptp->pps_source = pps_register_source(&pps, PTP_PPS_DEFAULTS); if (!ptp->pps_source) { + err = -EINVAL; pr_err("failed to register pps source\n"); goto no_pps; }

From: Mathieu Malaterre malat@debian.org

[ Upstream commit beba24ac59133cb36ecd03f9af9ccb11971ee20e ]

When both `CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y` and `CONFIG_UBSAN=y` are set, link step typically produce numberous warnings about orphan section:

+ powerpc-linux-gnu-ld -EB -m elf32ppc -Bstatic --orphan-handling=warn --build-id --gc-sections -X -o .tmp_vmlinux1 -T ./arch/powerpc/kernel/vmlinux.lds --who le-archive built-in.a --no-whole-archive --start-group lib/lib.a --end-group powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data393' from `init/main.o' being placed in section `.data..Lubsan_data393'. powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data394' from `init/main.o' being placed in section `.data..Lubsan_data394'. ... powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type11' from `init/main.o' being placed in section `.data..Lubsan_type11'. powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type12' from `init/main.o' being placed in section `.data..Lubsan_type12'. ...

This commit remove those warnings produced at W=1.

Link: https://www.mail-archive.com/linuxppc-dev@lists.ozlabs.org/msg135407.html Suggested-by: Nicholas Piggin npiggin@gmail.com Signed-off-by: Mathieu Malaterre malat@debian.org Signed-off-by: Michael Ellerman mpe@ellerman.id.au Signed-off-by: Sasha Levin sashal@kernel.org --- arch/powerpc/kernel/vmlinux.lds.S | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S index 07ae018e550e..53016c753f3c 100644 --- a/arch/powerpc/kernel/vmlinux.lds.S +++ b/arch/powerpc/kernel/vmlinux.lds.S @@ -296,6 +296,10 @@ SECTIONS #ifdef CONFIG_PPC32 .data : AT(ADDR(.data) - LOAD_OFFSET) { DATA_DATA +#ifdef CONFIG_UBSAN + *(.data..Lubsan_data*) + *(.data..Lubsan_type*) +#endif *(.data.rel*) *(SDATA_MAIN) *(.sdata2)

From: Martin Blumenstingl martin.blumenstingl@googlemail.com

[ Upstream commit 50314f98b0ac468218e7c9af8c99f215a35436df ]

Before this patch we are registering the internal clocks (for example on Meson8b, where the SAR ADC IP block implements the divider and gate clocks) with the following names: - /soc/cbus@c1100000/adc@8680#adc_div - /soc/cbus@c1100000/adc@8680#adc_en

This is bad because the common clock framework uses the clock to create a directory in <debugfs>/clk. With such name, the directory creation (silently) fails and the debugfs entry ends up being created at the debugfs root.

With this change, the new clock names are: - c1108680.adc#adc_div - c1108680.adc#adc_en

This matches the clock naming scheme used in the PWM, Ethernet and MMC drivers. It also fixes the problem with debugfs. The idea is shamelessly taken from commit b96e9eb62841c5 ("pwm: meson: Fix mux clock names").

Fixes: 3921db46a8c5bc ("iio: Convert to using %pOF instead of full_name") Signed-off-by: Martin Blumenstingl martin.blumenstingl@googlemail.com Signed-off-by: Jonathan Cameron Jonathan.Cameron@huawei.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/iio/adc/meson_saradc.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/iio/adc/meson_saradc.c b/drivers/iio/adc/meson_saradc.c index da4c391b8977..5dd104cf0939 100644 --- a/drivers/iio/adc/meson_saradc.c +++ b/drivers/iio/adc/meson_saradc.c @@ -587,8 +587,8 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, struct clk_init_data init; const char *clk_parents[1];

- init.name = devm_kasprintf(&indio_dev->dev, GFP_KERNEL, "%pOF#adc_div", - indio_dev->dev.of_node); + init.name = devm_kasprintf(&indio_dev->dev, GFP_KERNEL, "%s#adc_div", + dev_name(indio_dev->dev.parent)); if (!init.name) return -ENOMEM;

@@ -609,8 +609,8 @@ static int meson_sar_adc_clk_init(struct iio_dev *indio_dev, if (WARN_ON(IS_ERR(priv->adc_div_clk))) return PTR_ERR(priv->adc_div_clk);

- init.name = devm_kasprintf(&indio_dev->dev, GFP_KERNEL, "%pOF#adc_en", - indio_dev->dev.of_node); + init.name = devm_kasprintf(&indio_dev->dev, GFP_KERNEL, "%s#adc_en", + dev_name(indio_dev->dev.parent)); if (!init.name) return -ENOMEM;

From: Hans Verkuil hverkuil-cisco@xs4all.nl

[ Upstream commit 2912289a518077ddb8214e05336700148e97e235 ]

The v4l2_dv_timings_cap struct is used to do sanity checks when setting and enumerating DV timings, ensuring that only valid timings as per the HW capabilities are allowed.

However, many drivers just filled in 0 for the minimum width, height or pixelclock frequency. This can cause timings with e.g. 0 as width and height to be accepted, which will in turn lead to a potential division by zero.

Fill in proper values are minimum boundaries. 640x350 was chosen since it is the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the v4l2-dv-timings.h header).

Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/i2c/ad9389b.c | 2 +- drivers/media/i2c/adv7511.c | 2 +- drivers/media/i2c/adv7604.c | 4 ++-- drivers/media/i2c/adv7842.c | 4 ++-- drivers/media/i2c/tc358743.c | 2 +- drivers/media/i2c/ths8200.c | 2 +- 6 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/media/i2c/ad9389b.c b/drivers/media/i2c/ad9389b.c index 5b008b0002c0..aa8b04cfed0f 100644 --- a/drivers/media/i2c/ad9389b.c +++ b/drivers/media/i2c/ad9389b.c @@ -578,7 +578,7 @@ static const struct v4l2_dv_timings_cap ad9389b_timings_cap = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1200, 25000000, 170000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 170000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | diff --git a/drivers/media/i2c/adv7511.c b/drivers/media/i2c/adv7511.c index f3899cc84e27..88349b5053cc 100644 --- a/drivers/media/i2c/adv7511.c +++ b/drivers/media/i2c/adv7511.c @@ -130,7 +130,7 @@ static const struct v4l2_dv_timings_cap adv7511_timings_cap = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, ADV7511_MAX_WIDTH, 0, ADV7511_MAX_HEIGHT, + V4L2_INIT_BT_TIMINGS(640, ADV7511_MAX_WIDTH, 350, ADV7511_MAX_HEIGHT, ADV7511_MIN_PIXELCLOCK, ADV7511_MAX_PIXELCLOCK, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c index c78698199ac5..f01964c36ad5 100644 --- a/drivers/media/i2c/adv7604.c +++ b/drivers/media/i2c/adv7604.c @@ -766,7 +766,7 @@ static const struct v4l2_dv_timings_cap adv7604_timings_cap_analog = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1200, 25000000, 170000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 170000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | @@ -777,7 +777,7 @@ static const struct v4l2_dv_timings_cap adv76xx_timings_cap_digital = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1200, 25000000, 225000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 225000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | diff --git a/drivers/media/i2c/adv7842.c b/drivers/media/i2c/adv7842.c index 71fe56565f75..bb43a75ed6d0 100644 --- a/drivers/media/i2c/adv7842.c +++ b/drivers/media/i2c/adv7842.c @@ -663,7 +663,7 @@ static const struct v4l2_dv_timings_cap adv7842_timings_cap_analog = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1200, 25000000, 170000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 170000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | @@ -674,7 +674,7 @@ static const struct v4l2_dv_timings_cap adv7842_timings_cap_digital = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1200, 25000000, 225000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 25000000, 225000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | V4L2_DV_BT_CAP_REDUCED_BLANKING | diff --git a/drivers/media/i2c/tc358743.c b/drivers/media/i2c/tc358743.c index ff25ea9aca48..26070fb6ce4e 100644 --- a/drivers/media/i2c/tc358743.c +++ b/drivers/media/i2c/tc358743.c @@ -59,7 +59,7 @@ static const struct v4l2_dv_timings_cap tc358743_timings_cap = { /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, /* Pixel clock from REF_01 p. 20. Min/max height/width are unknown */ - V4L2_INIT_BT_TIMINGS(1, 10000, 1, 10000, 0, 165000000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1200, 13000000, 165000000, V4L2_DV_BT_STD_CEA861 | V4L2_DV_BT_STD_DMT | V4L2_DV_BT_STD_GTF | V4L2_DV_BT_STD_CVT, V4L2_DV_BT_CAP_PROGRESSIVE | diff --git a/drivers/media/i2c/ths8200.c b/drivers/media/i2c/ths8200.c index 498ad2368cbc..f5ee28058ea2 100644 --- a/drivers/media/i2c/ths8200.c +++ b/drivers/media/i2c/ths8200.c @@ -49,7 +49,7 @@ static const struct v4l2_dv_timings_cap ths8200_timings_cap = { .type = V4L2_DV_BT_656_1120, /* keep this initialization for compatibility with GCC < 4.4.6 */ .reserved = { 0 }, - V4L2_INIT_BT_TIMINGS(0, 1920, 0, 1080, 25000000, 148500000, + V4L2_INIT_BT_TIMINGS(640, 1920, 350, 1080, 25000000, 148500000, V4L2_DV_BT_STD_CEA861, V4L2_DV_BT_CAP_PROGRESSIVE) };

From: Michael Straube straube.linux@gmail.com

[ Upstream commit 64c4c4ca6c129a4191e8e1e91b2d5d9b8d08c518 ]

Add a test for successful call to cdev_alloc() to avoid potential null dereference. Issue reported by smatch.

Signed-off-by: Michael Straube straube.linux@gmail.com Fixes: 874bcba65f9a ("staging: pi433: New driver") Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/staging/pi433/pi433_if.c | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/drivers/staging/pi433/pi433_if.c b/drivers/staging/pi433/pi433_if.c index c85a805a1243..a497ec197872 100644 --- a/drivers/staging/pi433/pi433_if.c +++ b/drivers/staging/pi433/pi433_if.c @@ -1255,6 +1255,10 @@ static int pi433_probe(struct spi_device *spi)

/* create cdev */ device->cdev = cdev_alloc(); + if (!device->cdev) { + dev_dbg(device->dev, "allocation of cdev failed"); + goto cdev_failed; + } device->cdev->owner = THIS_MODULE; cdev_init(device->cdev, &pi433_fops); retval = cdev_add(device->cdev, device->devt, 1);

From: Jaegeuk Kim jaegeuk@kernel.org

[ Upstream commit f5d5510e7389fa264337fb524346bac9eb93adc8 ]

After merging the f2fs tree, today's linux-next build (x86_64_allmodconfig) produced this warning:

In file included from fs/f2fs/dir.c:11: fs/f2fs/f2fs.h: In function '__mark_inode_dirty_flag': fs/f2fs/f2fs.h:2388:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (set) ^ fs/f2fs/f2fs.h:2390:2: note: here case FI_DATA_EXIST: ^~~~

Exposed by my use of -Wimplicit-fallthrough

Reported-by: Stephen Rothwell sfr@canb.auug.org.au Signed-off-by: Jaegeuk Kim jaegeuk@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- fs/f2fs/f2fs.h | 1 + 1 file changed, 1 insertion(+)

diff --git a/fs/f2fs/f2fs.h b/fs/f2fs/f2fs.h index ecb735142276..462a2fb8aa69 100644 --- a/fs/f2fs/f2fs.h +++ b/fs/f2fs/f2fs.h @@ -2311,6 +2311,7 @@ static inline void __mark_inode_dirty_flag(struct inode *inode, case FI_NEW_INODE: if (set) return; + /* fall through */ case FI_DATA_EXIST: case FI_INLINE_DOTS: case FI_PIN_FILE:

From: Tiezhu Yang kernelpatch@126.com

[ Upstream commit f6176473a0c7472380eef72ebeb330cf9485bf0a ]

When call f2fs_acl_create_masq() failed, the caller f2fs_acl_create() should return -EIO instead of -ENOMEM, this patch makes it consistent with posix_acl_create() which has been fixed in commit beaf226b863a ("posix_acl: don't ignore return value of posix_acl_create_masq()").

Fixes: 83dfe53c185e ("f2fs: fix reference leaks in f2fs_acl_create") Signed-off-by: Tiezhu Yang kernelpatch@126.com Reviewed-by: Chao Yu yuchao0@huawei.com Signed-off-by: Jaegeuk Kim jaegeuk@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- fs/f2fs/acl.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)

diff --git a/fs/f2fs/acl.c b/fs/f2fs/acl.c index 111824199a88..b9fe937a3c70 100644 --- a/fs/f2fs/acl.c +++ b/fs/f2fs/acl.c @@ -352,12 +352,14 @@ static int f2fs_acl_create(struct inode *dir, umode_t *mode, return PTR_ERR(p);

clone = f2fs_acl_clone(p, GFP_NOFS); - if (!clone) - goto no_mem; + if (!clone) { + ret = -ENOMEM; + goto release_acl; + }

ret = f2fs_acl_create_masq(clone, mode); if (ret < 0) - goto no_mem_clone; + goto release_clone;

if (ret == 0) posix_acl_release(clone); @@ -371,11 +373,11 @@ static int f2fs_acl_create(struct inode *dir, umode_t *mode,

return 0;

-no_mem_clone: +release_clone: posix_acl_release(clone); -no_mem: +release_acl: posix_acl_release(p); - return -ENOMEM; + return ret; }

int f2fs_init_acl(struct inode *inode, struct inode *dir, struct page *ipage,

From: Will Deacon will.deacon@arm.com

[ Upstream commit 6460d32014717686d3b7963595950ba2c6d1bb5e ]

A relatively standard idiom for ensuring that a pair of MMIO writes to a device arrive at that device with a specified minimum delay between them is as follows:

writel_relaxed(42, dev_base + CTL1); readl(dev_base + CTL1); udelay(10); writel_relaxed(42, dev_base + CTL2);

the intention being that the read-back from the device will push the prior write to CTL1, and the udelay will hold up the write to CTL1 until at least 10us have elapsed.

Unfortunately, on arm64 where the underlying delay loop is implemented as a read of the architected counter, the CPU does not guarantee ordering from the readl() to the delay loop and therefore the delay loop could in theory be speculated and not provide the desired interval between the two writes.

Fix this in a similar manner to PowerPC by introducing a dummy control dependency on the output of readX() which, combined with the ISB in the read of the architected counter, guarantees that a subsequent delay loop can not be executed until the readX() has returned its result.

Cc: Benjamin Herrenschmidt benh@kernel.crashing.org Cc: Arnd Bergmann arnd@arndb.de Signed-off-by: Will Deacon will.deacon@arm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm64/include/asm/io.h | 31 +++++++++++++++++++++++-------- 1 file changed, 23 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h index 35b2e50f17fb..b2bc7dbc1fa6 100644 --- a/arch/arm64/include/asm/io.h +++ b/arch/arm64/include/asm/io.h @@ -106,7 +106,22 @@ static inline u64 __raw_readq(const volatile void __iomem *addr) }

/* IO barriers */ -#define __iormb() rmb() +#define __iormb(v) \ +({ \ + unsigned long tmp; \ + \ + rmb(); \ + \ + /* \ + * Create a dummy control dependency from the IO read to any \ + * later instructions. This ensures that a subsequent call to \ + * udelay() will be ordered due to the ISB in get_cycles(). \ + */ \ + asm volatile("eor %0, %1, %1\n" \ + "cbnz %0, ." \ + : "=r" (tmp) : "r" (v) : "memory"); \ +}) + #define __iowmb() wmb()

#define mmiowb() do { } while (0) @@ -131,10 +146,10 @@ static inline u64 __raw_readq(const volatile void __iomem *addr) * following Normal memory access. Writes are ordered relative to any prior * Normal memory access. */ -#define readb(c) ({ u8 __v = readb_relaxed(c); __iormb(); __v; }) -#define readw(c) ({ u16 __v = readw_relaxed(c); __iormb(); __v; }) -#define readl(c) ({ u32 __v = readl_relaxed(c); __iormb(); __v; }) -#define readq(c) ({ u64 __v = readq_relaxed(c); __iormb(); __v; }) +#define readb(c) ({ u8 __v = readb_relaxed(c); __iormb(__v); __v; }) +#define readw(c) ({ u16 __v = readw_relaxed(c); __iormb(__v); __v; }) +#define readl(c) ({ u32 __v = readl_relaxed(c); __iormb(__v); __v; }) +#define readq(c) ({ u64 __v = readq_relaxed(c); __iormb(__v); __v; })

#define writeb(v,c) ({ __iowmb(); writeb_relaxed((v),(c)); }) #define writew(v,c) ({ __iowmb(); writew_relaxed((v),(c)); }) @@ -185,9 +200,9 @@ extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size); /* * io{read,write}{16,32,64}be() macros */ -#define ioread16be(p) ({ __u16 __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(); __v; }) -#define ioread32be(p) ({ __u32 __v = be32_to_cpu((__force __be32)__raw_readl(p)); __iormb(); __v; }) -#define ioread64be(p) ({ __u64 __v = be64_to_cpu((__force __be64)__raw_readq(p)); __iormb(); __v; }) +#define ioread16be(p) ({ __u16 __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(__v); __v; }) +#define ioread32be(p) ({ __u32 __v = be32_to_cpu((__force __be32)__raw_readl(p)); __iormb(__v); __v; }) +#define ioread64be(p) ({ __u64 __v = be64_to_cpu((__force __be64)__raw_readq(p)); __iormb(__v); __v; })

#define iowrite16be(v,p) ({ __iowmb(); __raw_writew((__force __u16)cpu_to_be16(v), p); }) #define iowrite32be(v,p) ({ __iowmb(); __raw_writel((__force __u32)cpu_to_be32(v), p); })

From: Young Xiao YangX92@hotmail.com

[ Upstream commit a11f6ca9aef989b56cd31ff4ee2af4fb31a172ec ]

__vdc_tx_trigger should only loop on EAGAIN a finite number of times.

See commit adddc32d6fde ("sunvnet: Do not spin in an infinite loop when vio_ldc_send() returns EAGAIN") for detail.

Signed-off-by: Young Xiao YangX92@hotmail.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/block/sunvdc.c | 5 +++++ 1 file changed, 5 insertions(+)

diff --git a/drivers/block/sunvdc.c b/drivers/block/sunvdc.c index f68e9baffad7..5d7024057540 100644 --- a/drivers/block/sunvdc.c +++ b/drivers/block/sunvdc.c @@ -45,6 +45,8 @@ MODULE_VERSION(DRV_MODULE_VERSION); #define WAITING_FOR_GEN_CMD 0x04 #define WAITING_FOR_ANY -1

+#define VDC_MAX_RETRIES 10 + static struct workqueue_struct *sunvdc_wq;

struct vdc_req_entry { @@ -431,6 +433,7 @@ static int __vdc_tx_trigger(struct vdc_port *port) .end_idx = dr->prod, }; int err, delay; + int retries = 0;

hdr.seq = dr->snd_nxt; delay = 1; @@ -443,6 +446,8 @@ static int __vdc_tx_trigger(struct vdc_port *port) udelay(delay); if ((delay <<= 1) > 128) delay = 128; + if (retries++ > VDC_MAX_RETRIES) + break; } while (err == -EAGAIN);

if (err == -ENOTCONN)

From: "J. Bruce Fields" bfields@redhat.com

[ Upstream commit 62a063b8e7d1db684db3f207261a466fa3194e72 ]

Anatoly Trosinenko reports that this:

1) Checkout fresh master Linux branch (tested with commit e195ca6cb) 2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build 3) From `kvm-xfstests shell`:

results in NULL dereference in locks_end_grace.

Check that nfsd has been started before trying to end the grace period.

Reported-by: Anatoly Trosinenko anatoly.trosinenko@gmail.com Signed-off-by: J. Bruce Fields bfields@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- fs/nfsd/nfsctl.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/fs/nfsd/nfsctl.c b/fs/nfsd/nfsctl.c index 7fb9f7c667b1..899174c7a8ae 100644 --- a/fs/nfsd/nfsctl.c +++ b/fs/nfsd/nfsctl.c @@ -1126,6 +1126,8 @@ static ssize_t write_v4_end_grace(struct file *file, char *buf, size_t size) case 'Y': case 'y': case '1': + if (nn->nfsd_serv) + return -EBUSY; nfsd4_end_grace(nn); break; default:

From: Sean Paul seanpaul@chromium.org

[ Upstream commit c232e9f41b136c141df9938024e521191a7b910d ]

Instead of always re-initializing the variables we need to clean up on out, move the re-initialization into the branch that goes back to retry label.

This is a lateral move right now, but will allow us to pull out the modeset locking into common code. I kept this change separate to make things easier to review.

Changes in v2: - None

Reviewed-by: Daniel Vetter daniel@ffwll.ch Signed-off-by: Sean Paul seanpaul@chromium.org Link: https://patchwork.freedesktop.org/patch/msgid/20181129150423.239081-2-sean@p... Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/drm_crtc.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 9cbe8f5c9aca..ed9d7fc4cb2c 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -567,9 +567,9 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, struct drm_mode_crtc *crtc_req = data; struct drm_crtc *crtc; struct drm_plane *plane; - struct drm_connector **connector_set, *connector; - struct drm_framebuffer *fb; - struct drm_display_mode *mode; + struct drm_connector **connector_set = NULL, *connector; + struct drm_framebuffer *fb = NULL; + struct drm_display_mode *mode = NULL; struct drm_mode_set set; uint32_t __user *set_connectors_ptr; struct drm_modeset_acquire_ctx ctx; @@ -598,10 +598,6 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, mutex_lock(&crtc->dev->mode_config.mutex); drm_modeset_acquire_init(&ctx, DRM_MODESET_ACQUIRE_INTERRUPTIBLE); retry: - connector_set = NULL; - fb = NULL; - mode = NULL; - ret = drm_modeset_lock_all_ctx(crtc->dev, &ctx); if (ret) goto out; @@ -763,6 +759,12 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, } kfree(connector_set); drm_mode_destroy(dev, mode); + + /* In case we need to retry... */ + connector_set = NULL; + fb = NULL; + mode = NULL; + if (ret == -EDEADLK) { ret = drm_modeset_backoff(&ctx); if (!ret)

From: Will Deacon will.deacon@arm.com

[ Upstream commit 1b57ec8c75279b873639eb44a215479236f93481 ]

As of commit 6460d3201471 ("arm64: io: Ensure calls to delay routines are ordered against prior readX()"), MMIO reads smaller than 64 bits fail to compile under clang because we end up mixing 32-bit and 64-bit register operands for the same data processing instruction:

./include/asm-generic/io.h:695:9: warning: value size does not match register size specified by the constraint and modifier [-Wasm-operand-widths] return readb(addr); ^ ./arch/arm64/include/asm/io.h:147:58: note: expanded from macro 'readb' ^ ./include/asm-generic/io.h:695:9: note: use constraint modifier "w" ./arch/arm64/include/asm/io.h:147:50: note: expanded from macro 'readb' ^ ./arch/arm64/include/asm/io.h:118:24: note: expanded from macro '__iormb' asm volatile("eor %0, %1, %1\n" \ ^

Fix the build by casting the macro argument to 'unsigned long' when used as an input to the inline asm.

Reported-by: Nick Desaulniers nick.desaulniers@gmail.com Reported-by: Nathan Chancellor natechancellor@gmail.com Signed-off-by: Will Deacon will.deacon@arm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm64/include/asm/io.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h index b2bc7dbc1fa6..49bb9a020a09 100644 --- a/arch/arm64/include/asm/io.h +++ b/arch/arm64/include/asm/io.h @@ -119,7 +119,8 @@ static inline u64 __raw_readq(const volatile void __iomem *addr) */ \ asm volatile("eor %0, %1, %1\n" \ "cbnz %0, ." \ - : "=r" (tmp) : "r" (v) : "memory"); \ + : "=r" (tmp) : "r" ((unsigned long)(v)) \ + : "memory"); \ })

#define __iowmb() wmb()

From: Thara Gopinath thara.gopinath@linaro.org

[ Upstream commit 68000a0d983f539c95ebe5dccd4f29535c7ac0af ]

Sysfs interface to update cooling device cur_state does not currently holding cooling device lock sometimes leading to stale values in cur_state if getting updated simultanelously from user space and thermal framework. Adding the proper locking code fixes this issue.

Signed-off-by: Thara Gopinath thara.gopinath@linaro.org Signed-off-by: Zhang Rui rui.zhang@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/thermal/thermal_sysfs.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/thermal/thermal_sysfs.c b/drivers/thermal/thermal_sysfs.c index 2241ceae7d7f..aa99edb4dff7 100644 --- a/drivers/thermal/thermal_sysfs.c +++ b/drivers/thermal/thermal_sysfs.c @@ -712,11 +712,14 @@ cur_state_store(struct device *dev, struct device_attribute *attr, if ((long)state < 0) return -EINVAL;

+ mutex_lock(&cdev->lock); + result = cdev->ops->set_cur_state(cdev, state); - if (result) - return result; - thermal_cooling_device_stats_update(cdev, state); - return count; + if (!result) + thermal_cooling_device_stats_update(cdev, state); + + mutex_unlock(&cdev->lock); + return result ? result : count; }

static struct device_attribute

From: Harald Freudenberger freude@linux.ibm.com

[ Upstream commit be534791011100d204602e2e0496e9e6ce8edf63 ]

There exist very few ap messages which need to have the 'special' flag enabled. This flag tells the firmware layer to do some pre- and maybe postprocessing. However, it may happen that this special flag is enabled but the firmware is unable to deal with this kind of message and thus returns with reply code 0x41. For example older firmware may not know the newest messages triggered by the zcrypt device driver and thus react with reject and the named reply code. Unfortunately this reply code is not known to the zcrypt error routines and thus default behavior is to switch the ap queue offline.

This patch now makes the ap error routine aware of the reply code and so userspace is informed about the bad processing result but the queue is not switched to offline state any more.

Signed-off-by: Harald Freudenberger freude@linux.ibm.com Signed-off-by: Martin Schwidefsky schwidefsky@de.ibm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/s390/include/uapi/asm/zcrypt.h | 4 ++-- drivers/s390/crypto/zcrypt_error.h | 2 ++ 2 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/s390/include/uapi/asm/zcrypt.h b/arch/s390/include/uapi/asm/zcrypt.h index 2bb1f3bb98ac..48c784f2101a 100644 --- a/arch/s390/include/uapi/asm/zcrypt.h +++ b/arch/s390/include/uapi/asm/zcrypt.h @@ -147,8 +147,8 @@ struct ica_xcRB { * @cprb_len: CPRB header length [0x0020] * @cprb_ver_id: CPRB version id. [0x04] * @pad_000: Alignment pad bytes - * @flags: Admin cmd [0x80] or functional cmd [0x00] - * @func_id: Function id / subtype [0x5434] + * @flags: Admin bit [0x80], Special bit [0x20] + * @func_id: Function id / subtype [0x5434] "T4" * @source_id: Source id [originator id] * @target_id: Target id [usage/ctrl domain id] * @ret_code: Return code diff --git a/drivers/s390/crypto/zcrypt_error.h b/drivers/s390/crypto/zcrypt_error.h index 6f7ebc1dbe10..2e1a27bd97d1 100644 --- a/drivers/s390/crypto/zcrypt_error.h +++ b/drivers/s390/crypto/zcrypt_error.h @@ -52,6 +52,7 @@ struct error_hdr { #define REP82_ERROR_FORMAT_FIELD 0x29 #define REP82_ERROR_INVALID_COMMAND 0x30 #define REP82_ERROR_MALFORMED_MSG 0x40 +#define REP82_ERROR_INVALID_SPECIAL_CMD 0x41 #define REP82_ERROR_INVALID_DOMAIN_PRECHECK 0x42 #define REP82_ERROR_RESERVED_FIELDO 0x50 /* old value */ #define REP82_ERROR_WORD_ALIGNMENT 0x60 @@ -90,6 +91,7 @@ static inline int convert_error(struct zcrypt_queue *zq, case REP88_ERROR_MESSAGE_MALFORMD: case REP82_ERROR_INVALID_DOMAIN_PRECHECK: case REP82_ERROR_INVALID_DOMAIN_PENDING: + case REP82_ERROR_INVALID_SPECIAL_CMD: // REP88_ERROR_INVALID_KEY // '82' CEX2A // REP88_ERROR_OPERAND // '84' CEX2A // REP88_ERROR_OPERAND_EVEN_MOD // '85' CEX2A

From: Mark Rutland mark.rutland@arm.com

[ Upstream commit 6e803e2e6e367db9a0d6ecae1bd24bb5752011bd ]

The core ftrace code requires that when it is handed the PC of an instrumented function, this PC is the address of the instrumented instruction. This is necessary so that the core ftrace code can identify the specific instrumentation site. Since the instrumented function will be a BL, the address of the instrumented function is LR - 4 at entry to the ftrace code.

This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers, which acquire the PC of the instrumented function.

The mcount_get_lr helper is used to acquire the LR of the instrumented function, whose value does not require this adjustment, and cannot be adjusted to anything meaningful. No adjustment of this value is made on other architectures, including arm. However, arm64 adjusts this value by 4.

This patch brings arm64 in line with other architectures and removes the adjustment of the LR value.

Signed-off-by: Mark Rutland mark.rutland@arm.com Cc: AKASHI Takahiro takahiro.akashi@linaro.org Cc: Ard Biesheuvel ard.biesheuvel@linaro.org Cc: Catalin Marinas catalin.marinas@arm.com Cc: Torsten Duwe duwe@suse.de Cc: Will Deacon will.deacon@arm.com Signed-off-by: Will Deacon will.deacon@arm.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm64/kernel/entry-ftrace.S | 1 - 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/kernel/entry-ftrace.S b/arch/arm64/kernel/entry-ftrace.S index 1175f5827ae1..295951f3172e 100644 --- a/arch/arm64/kernel/entry-ftrace.S +++ b/arch/arm64/kernel/entry-ftrace.S @@ -79,7 +79,6 @@ .macro mcount_get_lr reg ldr \reg, [x29] ldr \reg, [\reg, #8] - mcount_adjust_addr \reg, \reg .endm

.macro mcount_get_lr_addr reg

From: Lubomir Rintel lkundrak@v3.sk

[ Upstream commit 1147e05ac9fc2ef86a3691e7ca5c2db7602d81dd ]

Marvell keeps their MMP2 datasheet secret, but there are good clues that TWSI2 is not on 0xd4025000 on that platform, not does it use IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:

arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58

I'm taking a somewhat educated guess that is probably a copy & paste error from PXA168 or PXA910 and that the real controller in fact hides at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.

I'm also copying some properties from TWSI1 that were missing or incorrect.

Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.

Signed-off-by: Lubomir Rintel lkundrak@v3.sk Tested-by: Pavel Machek pavel@ucw.cz Signed-off-by: Olof Johansson olof@lixom.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/mmp2.dtsi | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi index 766bbb8495b6..47e5b63339d1 100644 --- a/arch/arm/boot/dts/mmp2.dtsi +++ b/arch/arm/boot/dts/mmp2.dtsi @@ -220,12 +220,15 @@ status = "disabled"; };

- twsi2: i2c@d4025000 { + twsi2: i2c@d4031000 { compatible = "mrvl,mmp-twsi"; - reg = <0xd4025000 0x1000>; - interrupts = <58>; + reg = <0xd4031000 0x1000>; + interrupt-parent = <&intcmux17>; + interrupts = <0>; clocks = <&soc_clocks MMP2_CLK_TWSI1>; resets = <&soc_clocks MMP2_CLK_TWSI1>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; };

From: Lubomir Rintel lkundrak@v3.sk

[ Upstream commit f36797ee43802b367e59f0f9a9805304a4ff0c98 ]

The device-tree booted MMP2 needs to enable the timer clock, otherwise it would stop ticking when the boot finishes.

It can also use the clock rate from the clk, the non-DT boards need to keep using the hardcoded rates.

Signed-off-by: Lubomir Rintel lkundrak@v3.sk Acked-by: Pavel Machek pavel@ucw.cz Signed-off-by: Olof Johansson olof@lixom.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-mmp/common.h | 2 +- arch/arm/mach-mmp/mmp2.c | 2 +- arch/arm/mach-mmp/pxa168.c | 2 +- arch/arm/mach-mmp/time.c | 32 ++++++++++++++++++++------------ 4 files changed, 23 insertions(+), 15 deletions(-)

diff --git a/arch/arm/mach-mmp/common.h b/arch/arm/mach-mmp/common.h index 7e284d9c429f..5ac2851ef5d3 100644 --- a/arch/arm/mach-mmp/common.h +++ b/arch/arm/mach-mmp/common.h @@ -2,7 +2,7 @@ #include <linux/reboot.h> #define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)

-extern void timer_init(int irq); +extern void timer_init(int irq, unsigned long rate);

extern void __init mmp_map_io(void); extern void mmp_restart(enum reboot_mode, const char *); diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c index afba5460cdaf..fb3e7e32c882 100644 --- a/arch/arm/mach-mmp/mmp2.c +++ b/arch/arm/mach-mmp/mmp2.c @@ -134,7 +134,7 @@ void __init mmp2_timer_init(void) clk_rst = APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1); __raw_writel(clk_rst, APBC_TIMERS);

- timer_init(IRQ_MMP2_TIMER1); + timer_init(IRQ_MMP2_TIMER1, 6500000); }

/* on-chip devices */ diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c index 0f5f16fb8c66..77a358165a56 100644 --- a/arch/arm/mach-mmp/pxa168.c +++ b/arch/arm/mach-mmp/pxa168.c @@ -79,7 +79,7 @@ void __init pxa168_timer_init(void) /* 3.25MHz, bus/functional clock enabled, release reset */ __raw_writel(TIMER_CLK_RST, APBC_TIMERS);

- timer_init(IRQ_PXA168_TIMER1); + timer_init(IRQ_PXA168_TIMER1, 6500000); }

void pxa168_clear_keypad_wakeup(void) diff --git a/arch/arm/mach-mmp/time.c b/arch/arm/mach-mmp/time.c index 96ad1db0b04b..eab0fd8a7343 100644 --- a/arch/arm/mach-mmp/time.c +++ b/arch/arm/mach-mmp/time.c @@ -22,6 +22,7 @@ #include <linux/kernel.h> #include <linux/interrupt.h> #include <linux/clockchips.h> +#include <linux/clk.h>

#include <linux/io.h> #include <linux/irq.h> @@ -38,12 +39,6 @@ #include "cputype.h" #include "clock.h"

-#ifdef CONFIG_CPU_MMP2 -#define MMP_CLOCK_FREQ 6500000 -#else -#define MMP_CLOCK_FREQ 3250000 -#endif - #define TIMERS_VIRT_BASE TIMERS1_VIRT_BASE

#define MAX_DELTA (0xfffffffe) @@ -189,19 +184,18 @@ static struct irqaction timer_irq = { .dev_id = &ckevt, };

-void __init timer_init(int irq) +void __init timer_init(int irq, unsigned long rate) { timer_config();

- sched_clock_register(mmp_read_sched_clock, 32, MMP_CLOCK_FREQ); + sched_clock_register(mmp_read_sched_clock, 32, rate);

ckevt.cpumask = cpumask_of(0);

setup_irq(irq, &timer_irq);

- clocksource_register_hz(&cksrc, MMP_CLOCK_FREQ); - clockevents_config_and_register(&ckevt, MMP_CLOCK_FREQ, - MIN_DELTA, MAX_DELTA); + clocksource_register_hz(&cksrc, rate); + clockevents_config_and_register(&ckevt, rate, MIN_DELTA, MAX_DELTA); }

#ifdef CONFIG_OF @@ -213,7 +207,9 @@ static const struct of_device_id mmp_timer_dt_ids[] = { void __init mmp_dt_init_timer(void) { struct device_node *np; + struct clk *clk; int irq, ret; + unsigned long rate;

np = of_find_matching_node(NULL, mmp_timer_dt_ids); if (!np) { @@ -221,6 +217,18 @@ void __init mmp_dt_init_timer(void) goto out; }

+ clk = of_clk_get(np, 0); + if (!IS_ERR(clk)) { + ret = clk_prepare_enable(clk); + if (ret) + goto out; + rate = clk_get_rate(clk) / 2; + } else if (cpu_is_pj4()) { + rate = 6500000; + } else { + rate = 3250000; + } + irq = irq_of_parse_and_map(np, 0); if (!irq) { ret = -EINVAL; @@ -231,7 +239,7 @@ void __init mmp_dt_init_timer(void) ret = -ENOMEM; goto out; } - timer_init(irq); + timer_init(irq, rate); return; out: pr_err("Failed to get timer from device tree with error:%d\n", ret);

From: Sebastian Andrzej Siewior bigeasy@linutronix.de

[ Upstream commit 6637401c35b2f327a35d27f44bda05e327f2f017 ]

Every user of user_insn() passes an user memory pointer to this macro.

Add might_fault() to user_insn() so we can spot users which are using this macro in sections where page faulting is not allowed.

[ bp: Space it out to make it more visible. ]

Signed-off-by: Sebastian Andrzej Siewior bigeasy@linutronix.de Signed-off-by: Borislav Petkov bp@suse.de Reviewed-by: Rik van Riel riel@surriel.com Cc: "H. Peter Anvin" hpa@zytor.com Cc: "Jason A. Donenfeld" Jason@zx2c4.com Cc: Andy Lutomirski luto@kernel.org Cc: Dave Hansen dave.hansen@linux.intel.com Cc: Ingo Molnar mingo@redhat.com Cc: Jann Horn jannh@google.com Cc: Paolo Bonzini pbonzini@redhat.com Cc: Radim Krčmář rkrcmar@redhat.com Cc: Thomas Gleixner tglx@linutronix.de Cc: kvm ML kvm@vger.kernel.org Cc: x86-ml x86@kernel.org Link: https://lkml.kernel.org/r/20181128222035.2996-6-bigeasy@linutronix.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/x86/include/asm/fpu/internal.h | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/arch/x86/include/asm/fpu/internal.h b/arch/x86/include/asm/fpu/internal.h index 69dcdf195b61..fa2c93cb42a2 100644 --- a/arch/x86/include/asm/fpu/internal.h +++ b/arch/x86/include/asm/fpu/internal.h @@ -106,6 +106,9 @@ extern void fpstate_sanitize_xstate(struct fpu *fpu); #define user_insn(insn, output, input...) \ ({ \ int err; \ + \ + might_fault(); \ + \ asm volatile(ASM_STAC "\n" \ "1:" #insn "\n\t" \ "2: " ASM_CLAC "\n" \

From: Alexey Khoroshilov khoroshilov@ispras.ru

[ Upstream commit aa35dc3c71950e3fec3e230c06c27c0fbd0067f8 ]

If vpbe_set_default_output() or vpbe_set_default_mode() fails, vpbe_initialize() returns error code without releasing resources.

The patch adds error handling for that case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov khoroshilov@ispras.ru Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/platform/davinci/vpbe.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/media/platform/davinci/vpbe.c b/drivers/media/platform/davinci/vpbe.c index 18c035ef84cf..df1ae6b5c854 100644 --- a/drivers/media/platform/davinci/vpbe.c +++ b/drivers/media/platform/davinci/vpbe.c @@ -740,7 +740,7 @@ static int vpbe_initialize(struct device *dev, struct vpbe_device *vpbe_dev) if (ret) { v4l2_err(&vpbe_dev->v4l2_dev, "Failed to set default output %s", def_output); - return ret; + goto fail_kfree_amp; }

printk(KERN_NOTICE "Setting default mode to %s\n", def_mode); @@ -748,12 +748,15 @@ static int vpbe_initialize(struct device *dev, struct vpbe_device *vpbe_dev) if (ret) { v4l2_err(&vpbe_dev->v4l2_dev, "Failed to set default mode %s", def_mode); - return ret; + goto fail_kfree_amp; } vpbe_dev->initialized = 1; /* TBD handling of bootargs for default output and mode */ return 0;

+fail_kfree_amp: + mutex_lock(&vpbe_dev->lock); + kfree(vpbe_dev->amp); fail_kfree_encoders: kfree(vpbe_dev->encoders); fail_dev_unregister:

From: Max Filippov jcmvbkbc@gmail.com

[ Upstream commit f37598be4e3896359e87c824be57ddddc280cc3f ]

Rename SPI controller node in the XTFPGA DTS to spi@... This fixes the following build warnings:

arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_bridge): /soc/spi-master@0d0a0000: node name for SPI buses should be 'spi' arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge' arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_bridge): /soc/spi-master@0d0a0000: node name for SPI buses should be 'spi' arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge' arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_bridge): /soc/spi-master@0d0a0000: node name for SPI buses should be 'spi' arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge' arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_bridge): /soc/spi-master@0d0a0000: node name for SPI buses should be 'spi' arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge' arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_bridge): /soc/spi-master@0d0a0000: node name for SPI buses should be 'spi' arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'

Signed-off-by: Max Filippov jcmvbkbc@gmail.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/xtensa/boot/dts/xtfpga.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/xtensa/boot/dts/xtfpga.dtsi b/arch/xtensa/boot/dts/xtfpga.dtsi index 1090528825ec..e46ae07bab05 100644 --- a/arch/xtensa/boot/dts/xtfpga.dtsi +++ b/arch/xtensa/boot/dts/xtfpga.dtsi @@ -103,7 +103,7 @@ }; };

- spi0: spi-master@0d0a0000 { + spi0: spi@0d0a0000 { compatible = "cdns,xtfpga-spi"; #address-cells = <1>; #size-cells = <0>;

From: Marek Szyprowski m.szyprowski@samsung.com

[ Upstream commit 35a6054132286a4ab92b536595093b82e6bdfcbc ]

Power down feature of DWC2 module integrated in Samsung SoCs doesn't work properly or needs some additional handling in PHY or SoC glue layer, so disable it for now. Without disabling power down, DWC2 causes random memory trashes and fails enumeration if there is no USB link to host on driver probe.

Fixes: 03ea6d6e9e1ff1 ("usb: dwc2: Enable power down") Acked-by: Minas Harutyunyan hminas@synopsys.com Signed-off-by: Marek Szyprowski m.szyprowski@samsung.com Signed-off-by: Felipe Balbi felipe.balbi@linux.intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/usb/dwc2/params.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/dwc2/params.c b/drivers/usb/dwc2/params.c index ef2c199e6059..dff2c6e8d797 100644 --- a/drivers/usb/dwc2/params.c +++ b/drivers/usb/dwc2/params.c @@ -71,6 +71,13 @@ static void dwc2_set_his_params(struct dwc2_hsotg *hsotg) p->power_down = false; }

+static void dwc2_set_s3c6400_params(struct dwc2_hsotg *hsotg) +{ + struct dwc2_core_params *p = &hsotg->params; + + p->power_down = 0; +} + static void dwc2_set_rk_params(struct dwc2_hsotg *hsotg) { struct dwc2_core_params *p = &hsotg->params; @@ -151,7 +158,8 @@ const struct of_device_id dwc2_of_match_table[] = { { .compatible = "lantiq,arx100-usb", .data = dwc2_set_ltq_params }, { .compatible = "lantiq,xrx200-usb", .data = dwc2_set_ltq_params }, { .compatible = "snps,dwc2" }, - { .compatible = "samsung,s3c6400-hsotg" }, + { .compatible = "samsung,s3c6400-hsotg", + .data = dwc2_set_s3c6400_params }, { .compatible = "amlogic,meson8-usb", .data = dwc2_set_amlogic_params }, { .compatible = "amlogic,meson8b-usb",

From: Bart Van Assche bvanassche@acm.org

[ Upstream commit ce10a5b3954f2514af726beb78ed8d7350c5e41c ]

tk_core.seq is initialized open coded, but that misses to initialize the lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq consequently lack a name and are hard to read.

Use the proper initializer which takes care of the lockdep map initialization.

[ tglx: Massaged changelog ]

Signed-off-by: Bart Van Assche bvanassche@acm.org Signed-off-by: Thomas Gleixner tglx@linutronix.de Cc: peterz@infradead.org Cc: tj@kernel.org Cc: johannes.berg@intel.com Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.org Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/time/timekeeping.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/kernel/time/timekeeping.c b/kernel/time/timekeeping.c index f3b22f456fac..7846ce24ecc0 100644 --- a/kernel/time/timekeeping.c +++ b/kernel/time/timekeeping.c @@ -50,7 +50,9 @@ enum timekeeping_adv_mode { static struct { seqcount_t seq; struct timekeeper timekeeper; -} tk_core ____cacheline_aligned; +} tk_core ____cacheline_aligned = { + .seq = SEQCNT_ZERO(tk_core.seq), +};

static DEFINE_RAW_SPINLOCK(timekeeper_lock); static struct timekeeper shadow_timekeeper;

From: Chen-Yu Tsai wens@csie.org

[ Upstream commit 6e6da2039c82271dd873b9ad2b902a692a7dd554 ]

All the audio interfaces on Allwinner SoCs need to change their module clocks during operation, to switch between support for 44.1 kHz and 48 kHz family sample rates. The clock rate for the module clocks is governed by their upstream audio PLL. The module clocks themselves only have a gate, and sometimes a divider or mux. Thus any rate changes need to be propagated upstream.

Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve this.

Signed-off-by: Chen-Yu Tsai wens@csie.org Signed-off-by: Maxime Ripard maxime.ripard@bootlin.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/clk/sunxi-ng/ccu-sun8i-a33.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c index 13eb5b23c5e7..c40d572a7602 100644 --- a/drivers/clk/sunxi-ng/ccu-sun8i-a33.c +++ b/drivers/clk/sunxi-ng/ccu-sun8i-a33.c @@ -366,10 +366,10 @@ static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents, 0x0a4, static const char * const i2s_parents[] = { "pll-audio-8x", "pll-audio-4x", "pll-audio-2x", "pll-audio" }; static SUNXI_CCU_MUX_WITH_GATE(i2s0_clk, "i2s0", i2s_parents, - 0x0b0, 16, 2, BIT(31), 0); + 0x0b0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);

static SUNXI_CCU_MUX_WITH_GATE(i2s1_clk, "i2s1", i2s_parents, - 0x0b4, 16, 2, BIT(31), 0); + 0x0b4, 16, 2, BIT(31), CLK_SET_RATE_PARENT);

/* TODO: the parent for most of the USB clocks is not known */ static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M", @@ -446,7 +446,7 @@ static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve", static SUNXI_CCU_GATE(ac_dig_clk, "ac-dig", "pll-audio", 0x140, BIT(31), CLK_SET_RATE_PARENT); static SUNXI_CCU_GATE(ac_dig_4x_clk, "ac-dig-4x", "pll-audio-4x", - 0x140, BIT(30), 0); + 0x140, BIT(30), CLK_SET_RATE_PARENT); static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M", 0x144, BIT(31), 0);

From: Alex Deucher alexander.deucher@amd.com

[ Upstream commit de4aaab5cc9770a8c4dc13d9bfb6a83b06bba57e ]

Adjust limits for newer polaris variants.

v2: fix polaris11 kicker (Jerry)

Reviewed-by: Junwei Zhang Jerry.Zhang@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- .../drm/amd/powerplay/smumgr/polaris10_smumgr.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/amd/powerplay/smumgr/polaris10_smumgr.c b/drivers/gpu/drm/amd/powerplay/smumgr/polaris10_smumgr.c index 5b67f575cd34..45629f26dbc2 100644 --- a/drivers/gpu/drm/amd/powerplay/smumgr/polaris10_smumgr.c +++ b/drivers/gpu/drm/amd/powerplay/smumgr/polaris10_smumgr.c @@ -1528,8 +1528,21 @@ static int polaris10_populate_clock_stretcher_data_table(struct pp_hwmgr *hwmgr) efuse = efuse >> 24;

if (hwmgr->chip_id == CHIP_POLARIS10) { - min = 1000; - max = 2300; + if (hwmgr->is_kicker) { + min = 1200; + max = 2500; + } else { + min = 1000; + max = 2300; + } + } else if (hwmgr->chip_id == CHIP_POLARIS11) { + if (hwmgr->is_kicker) { + min = 900; + max = 2100; + } else { + min = 1100; + max = 2100; + } } else { min = 1100; max = 2100;

From: Alexander Duyck alexander.h.duyck@linux.intel.com

[ Upstream commit c37d721c68ad88925ba0e72f6e14acb829a8c6bb ]

Move the async_synchronize_full call out of __device_release_driver and into driver_detach.

The idea behind this is that the async_synchronize_full call will only guarantee that any existing async operations are flushed. This doesn't do anything to guarantee that a hotplug event that may occur while we are doing the release of the driver will not be asynchronously scheduled.

By moving this into the driver_detach path we can avoid potential deadlocks as we aren't holding the device lock at this point and we should not have the driver we want to flush loaded so the flush will take care of any asynchronous events the driver we are detaching might have scheduled.

Fixes: 765230b5f084 ("driver-core: add asynchronous probing support for drivers") Reviewed-by: Bart Van Assche bvanassche@acm.org Reviewed-by: Dan Williams dan.j.williams@intel.com Signed-off-by: Alexander Duyck alexander.h.duyck@linux.intel.com Reviewed-by: Luis Chamberlain mcgrof@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/base/dd.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/base/dd.c b/drivers/base/dd.c index 2607f859881a..7caa1adaf62a 100644 --- a/drivers/base/dd.c +++ b/drivers/base/dd.c @@ -926,9 +926,6 @@ static void __device_release_driver(struct device *dev, struct device *parent)

drv = dev->driver; if (drv) { - if (driver_allows_async_probing(drv)) - async_synchronize_full(); - while (device_links_busy(dev)) { device_unlock(dev); if (parent && dev->bus->need_parent_lock) @@ -1034,6 +1031,9 @@ void driver_detach(struct device_driver *drv) struct device_private *dev_prv; struct device *dev;

+ if (driver_allows_async_probing(drv)) + async_synchronize_full(); + for (;;) { spin_lock(&drv->p->klist_devices.k_lock); if (list_empty(&drv->p->klist_devices.k_list)) {

From: Kaike Wan kaike.wan@intel.com

[ Upstream commit ca95f802ef5139722acc8d30aeaab6fe5bbe939e ]

Currently, When a reserved operation is completed, its entry in the send queue will not be unreserved, which leads to the miscalculation of qp->s_avail and thus the triggering of a WARN_ON call trace. This patch fixes the problem by unreserving the reserved operation when it is completed.

Fixes: 856cc4c237ad ("IB/hfi1: Add the capability for reserved operations") Reviewed-by: Mike Marciniszyn mike.marciniszyn@intel.com Signed-off-by: Kaike Wan kaike.wan@intel.com Signed-off-by: Dennis Dalessandro dennis.dalessandro@intel.com Signed-off-by: Jason Gunthorpe jgg@mellanox.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/infiniband/hw/hfi1/rc.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/infiniband/hw/hfi1/rc.c b/drivers/infiniband/hw/hfi1/rc.c index 9bd63abb2dfe..6f013a565353 100644 --- a/drivers/infiniband/hw/hfi1/rc.c +++ b/drivers/infiniband/hw/hfi1/rc.c @@ -1157,6 +1157,7 @@ void hfi1_rc_send_complete(struct rvt_qp *qp, struct hfi1_opa_header *opah) if (cmp_psn(wqe->lpsn, qp->s_sending_psn) >= 0 && cmp_psn(qp->s_sending_psn, qp->s_sending_hpsn) <= 0) break; + rvt_qp_wqe_unreserve(qp, wqe); s_last = qp->s_last; trace_hfi1_qp_send_completion(qp, wqe, s_last); if (++s_last >= qp->s_size) @@ -1209,6 +1210,7 @@ static struct rvt_swqe *do_rc_completion(struct rvt_qp *qp, u32 s_last;

rvt_put_swqe(wqe); + rvt_qp_wqe_unreserve(qp, wqe); s_last = qp->s_last; trace_hfi1_qp_send_completion(qp, wqe, s_last); if (++s_last >= qp->s_size)

From: Nicholas Mc Guire hofrat@osadl.org

[ Upstream commit 59d646c775d6ae688ee90fda9f2a4270c47b7490 ]

kasprintf() may return NULL on failure of internal allocation thus the assigned label is not safe if not explicitly checked. On error mediatek_gpio_bank_probe() returns negative values so -ENOMEM in the (unlikely) failure case should be fine here.

Fixes: 4ba9c3afda41 ("gpio: mt7621: Add a driver for MT7621") Signed-off-by: Nicholas Mc Guire hofrat@osadl.org Reviewed-by: Bartosz Golaszewski bgolaszewski@baylibre.com Acked-by: Sean Wang sean.wang@kernel.org Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpio/gpio-mt7621.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/gpio/gpio-mt7621.c b/drivers/gpio/gpio-mt7621.c index d72af6f6cdbd..1ec95bc18f5b 100644 --- a/drivers/gpio/gpio-mt7621.c +++ b/drivers/gpio/gpio-mt7621.c @@ -244,6 +244,8 @@ mediatek_gpio_bank_probe(struct device *dev, rg->chip.of_xlate = mediatek_gpio_xlate; rg->chip.label = devm_kasprintf(dev, GFP_KERNEL, "%s-bank%d", dev_name(dev), bank); + if (!rg->chip.label) + return -ENOMEM;

ret = devm_gpiochip_add_data(dev, &rg->chip, mtk); if (ret < 0) {

From: Nicholas Mc Guire hofrat@osadl.org

[ Upstream commit a9d9f6b83f1bb05da849b3540e6d1f70ef1c2343 ]

devm_kstrdup() may return NULL if internal allocation failed. Thus using label, name is unsafe without checking. Therefor in the unlikely case of allocation failure, sx150x_probe() simply returns -ENOMEM.

Signed-off-by: Nicholas Mc Guire hofrat@osadl.org Fixes: 9e80f9064e73 ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver") Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/pinctrl-sx150x.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-sx150x.c b/drivers/pinctrl/pinctrl-sx150x.c index cbf58a10113d..4d87d75b9c6e 100644 --- a/drivers/pinctrl/pinctrl-sx150x.c +++ b/drivers/pinctrl/pinctrl-sx150x.c @@ -1166,7 +1166,6 @@ static int sx150x_probe(struct i2c_client *client, }

/* Register GPIO controller */ - pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); pctl->gpio.base = -1; pctl->gpio.ngpio = pctl->data->npins; pctl->gpio.get_direction = sx150x_gpio_get_direction; @@ -1180,6 +1179,10 @@ static int sx150x_probe(struct i2c_client *client, pctl->gpio.of_node = dev->of_node; #endif pctl->gpio.can_sleep = true; + pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); + if (!pctl->gpio.label) + return -ENOMEM; + /* * Setting multiple pins is not safe when all pins are not * handled by the same regmap register. The oscio pin (present @@ -1200,13 +1203,15 @@ static int sx150x_probe(struct i2c_client *client,

/* Add Interrupt support if an irq is specified */ if (client->irq > 0) { - pctl->irq_chip.name = devm_kstrdup(dev, client->name, - GFP_KERNEL); pctl->irq_chip.irq_mask = sx150x_irq_mask; pctl->irq_chip.irq_unmask = sx150x_irq_unmask; pctl->irq_chip.irq_set_type = sx150x_irq_set_type; pctl->irq_chip.irq_bus_lock = sx150x_irq_bus_lock; pctl->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock; + pctl->irq_chip.name = devm_kstrdup(dev, client->name, + GFP_KERNEL); + if (!pctl->irq_chip.name) + return -ENOMEM;

pctl->irq.masked = ~0; pctl->irq.sense = 0;

From: Russell King - ARM Linux linux@armlinux.org.uk

[ Upstream commit 84fb6c7feb1494ebb7d1ec8b95cfb7ada0264465 ]

It was noticed that unbinding and rebinding the KSZ8851 ethernet resulted in the driver reporting "failed to read device ID" at probe. Probing the reset line with a 'scope while repeatedly attempting to bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is constantly held at zero, meaning the device is held in reset, and does not respond on the SPI bus.

Experimentation with the startup delay on the regulator set to 50ms shows that the reset is positively released after 20ms.

Schematics for this board are not available, and the traces are buried in the inner layers of the board which makes tracing where the RSTN pin extremely difficult. We can only guess that the RSTN pin is wired to a reset generator chip driven off the ethernet supply, which fits the observed behaviour.

Include this delay in the regulator startup delay - effectively treating the reset as a "supply stable" indicator.

This can not be modelled as a delay in the KSZ8851 driver since the reset generation is board specific - if the RSTN pin had been wired to a GPIO, reset could be released earlier via the already provided support in the KSZ8851 driver.

This also got confirmed by Peter Ujfalusi peter.ujfalusi@ti.com based on Blaze schematics that should be very close to SDP4430:

TPS22902YFPR is used as the regulator switch (gpio48 controlled): Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV. (SCH Note: Threshold set at 90%. Vsense: 0.405V).

According to the TPS3808 data sheet the RESET delay time when Ct is open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.

Signed-off-by: Russell King rmk+kernel@armlinux.org.uk Reviewed-by: Peter Ujfalusi peter.ujfalusi@ti.com [tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by: Tony Lindgren tony@atomide.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/omap4-sdp.dts | 1 + 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 490726b52216..9dc7ec7655cb 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -33,6 +33,7 @@ gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; /* gpio line 48 */ enable-active-high; regulator-boot-on; + startup-delay-us = <25000>; };

vbat: fixedregulator-vbat {

From: Philipp Zabel p.zabel@pengutronix.de

[ Upstream commit 75fa6e4f83a0923fe753827d354998d448b4fd6a ]

Add support for the third loop filter mode V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY, and fix V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA and V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA controls.

The filter offset controls are signed values in the -6 to 6 range and are stored into the slice header fields slice_alpha_c0_offset_div2 and slice_beta_offset_div2. The actual filter offsets FilterOffsetA/B are double their value, in range of -12 to 12.

Rename variables to more closely match the nomenclature in the H.264 specification.

Signed-off-by: Philipp Zabel p.zabel@pengutronix.de Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/platform/coda/coda-bit.c | 19 +++++++++---------- drivers/media/platform/coda/coda-common.c | 15 +++++++-------- drivers/media/platform/coda/coda.h | 6 +++--- drivers/media/platform/coda/coda_regs.h | 2 +- 4 files changed, 20 insertions(+), 22 deletions(-)

diff --git a/drivers/media/platform/coda/coda-bit.c b/drivers/media/platform/coda/coda-bit.c index d26c2d85a009..d20d3df5778b 100644 --- a/drivers/media/platform/coda/coda-bit.c +++ b/drivers/media/platform/coda/coda-bit.c @@ -991,16 +991,15 @@ static int coda_start_encoding(struct coda_ctx *ctx) else coda_write(dev, CODA_STD_H264, CODA_CMD_ENC_SEQ_COD_STD); - if (ctx->params.h264_deblk_enabled) { - value = ((ctx->params.h264_deblk_alpha & - CODA_264PARAM_DEBLKFILTEROFFSETALPHA_MASK) << - CODA_264PARAM_DEBLKFILTEROFFSETALPHA_OFFSET) | - ((ctx->params.h264_deblk_beta & - CODA_264PARAM_DEBLKFILTEROFFSETBETA_MASK) << - CODA_264PARAM_DEBLKFILTEROFFSETBETA_OFFSET); - } else { - value = 1 << CODA_264PARAM_DISABLEDEBLK_OFFSET; - } + value = ((ctx->params.h264_disable_deblocking_filter_idc & + CODA_264PARAM_DISABLEDEBLK_MASK) << + CODA_264PARAM_DISABLEDEBLK_OFFSET) | + ((ctx->params.h264_slice_alpha_c0_offset_div2 & + CODA_264PARAM_DEBLKFILTEROFFSETALPHA_MASK) << + CODA_264PARAM_DEBLKFILTEROFFSETALPHA_OFFSET) | + ((ctx->params.h264_slice_beta_offset_div2 & + CODA_264PARAM_DEBLKFILTEROFFSETBETA_MASK) << + CODA_264PARAM_DEBLKFILTEROFFSETBETA_OFFSET); coda_write(dev, value, CODA_CMD_ENC_SEQ_264_PARA); break; case V4L2_PIX_FMT_JPEG: diff --git a/drivers/media/platform/coda/coda-common.c b/drivers/media/platform/coda/coda-common.c index bf7b8417c27f..19d92edcc981 100644 --- a/drivers/media/platform/coda/coda-common.c +++ b/drivers/media/platform/coda/coda-common.c @@ -1793,14 +1793,13 @@ static int coda_s_ctrl(struct v4l2_ctrl *ctrl) ctx->params.h264_max_qp = ctrl->val; break; case V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA: - ctx->params.h264_deblk_alpha = ctrl->val; + ctx->params.h264_slice_alpha_c0_offset_div2 = ctrl->val; break; case V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA: - ctx->params.h264_deblk_beta = ctrl->val; + ctx->params.h264_slice_beta_offset_div2 = ctrl->val; break; case V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_MODE: - ctx->params.h264_deblk_enabled = (ctrl->val == - V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_ENABLED); + ctx->params.h264_disable_deblocking_filter_idc = ctrl->val; break; case V4L2_CID_MPEG_VIDEO_H264_PROFILE: /* TODO: switch between baseline and constrained baseline */ @@ -1882,13 +1881,13 @@ static void coda_encode_ctrls(struct coda_ctx *ctx) v4l2_ctrl_new_std(&ctx->ctrls, &coda_ctrl_ops, V4L2_CID_MPEG_VIDEO_H264_MAX_QP, 0, 51, 1, 51); v4l2_ctrl_new_std(&ctx->ctrls, &coda_ctrl_ops, - V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA, 0, 15, 1, 0); + V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA, -6, 6, 1, 0); v4l2_ctrl_new_std(&ctx->ctrls, &coda_ctrl_ops, - V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA, 0, 15, 1, 0); + V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA, -6, 6, 1, 0); v4l2_ctrl_new_std_menu(&ctx->ctrls, &coda_ctrl_ops, V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_MODE, - V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED, 0x0, - V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_ENABLED); + V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY, + 0x0, V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_ENABLED); v4l2_ctrl_new_std_menu(&ctx->ctrls, &coda_ctrl_ops, V4L2_CID_MPEG_VIDEO_H264_PROFILE, V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE, 0x0, diff --git a/drivers/media/platform/coda/coda.h b/drivers/media/platform/coda/coda.h index 19ac0b9dc6eb..2469ca1dc598 100644 --- a/drivers/media/platform/coda/coda.h +++ b/drivers/media/platform/coda/coda.h @@ -115,9 +115,9 @@ struct coda_params { u8 h264_inter_qp; u8 h264_min_qp; u8 h264_max_qp; - u8 h264_deblk_enabled; - u8 h264_deblk_alpha; - u8 h264_deblk_beta; + u8 h264_disable_deblocking_filter_idc; + s8 h264_slice_alpha_c0_offset_div2; + s8 h264_slice_beta_offset_div2; u8 h264_profile_idc; u8 h264_level_idc; u8 mpeg4_intra_qp; diff --git a/drivers/media/platform/coda/coda_regs.h b/drivers/media/platform/coda/coda_regs.h index 5e7b00a97671..e675e38f3475 100644 --- a/drivers/media/platform/coda/coda_regs.h +++ b/drivers/media/platform/coda/coda_regs.h @@ -292,7 +292,7 @@ #define CODA_264PARAM_DEBLKFILTEROFFSETALPHA_OFFSET 8 #define CODA_264PARAM_DEBLKFILTEROFFSETALPHA_MASK 0x0f #define CODA_264PARAM_DISABLEDEBLK_OFFSET 6 -#define CODA_264PARAM_DISABLEDEBLK_MASK 0x01 +#define CODA_264PARAM_DISABLEDEBLK_MASK 0x03 #define CODA_264PARAM_CONSTRAINEDINTRAPREDFLAG_OFFSET 5 #define CODA_264PARAM_CONSTRAINEDINTRAPREDFLAG_MASK 0x01 #define CODA_264PARAM_CHROMAQPOFFSET_OFFSET 0

From: Dan Carpenter dan.carpenter@oracle.com

[ Upstream commit ca16b0fbb05242f18da9d810c07d3882ffed831c ]

Dan Carpenter reviewed the trace_stack.c code and figured he found an off by one bug.

"From reviewing the code, it seems possible for stack_trace_max.nr_entries to be set to .max_entries and in that case we would be reading one element beyond the end of the stack_dump_trace[] array. If it's not set to .max_entries then the bug doesn't affect runtime."

Although it looks to be the case, it is not. Because we have:

static unsigned long stack_dump_trace[STACK_TRACE_ENTRIES+1] = { [0 ... (STACK_TRACE_ENTRIES)] = ULONG_MAX };

struct stack_trace stack_trace_max = { .max_entries = STACK_TRACE_ENTRIES - 1, .entries = &stack_dump_trace[0], };

And:

stack_trace_max.nr_entries = x; for (; x < i; x++) stack_dump_trace[x] = ULONG_MAX;

Even if nr_entries equals max_entries, indexing with it into the stack_dump_trace[] array will not overflow the array. But if it is the case, the second part of the conditional that tests stack_dump_trace[nr_entries] to ULONG_MAX will always be true.

By applying Dan's patch, it removes the subtle aspect of it and makes the if conditional slightly more efficient.

Link: http://lkml.kernel.org/r/20180620110758.crunhd5bfep7zuiz@kili.mountain

Signed-off-by: Dan Carpenter dan.carpenter@oracle.com Signed-off-by: Steven Rostedt (VMware) rostedt@goodmis.org Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/trace/trace_stack.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/trace/trace_stack.c b/kernel/trace/trace_stack.c index 4237eba4ef20..6e3edd745c68 100644 --- a/kernel/trace/trace_stack.c +++ b/kernel/trace/trace_stack.c @@ -286,7 +286,7 @@ __next(struct seq_file *m, loff_t *pos) { long n = *pos - 1;

- if (n > stack_trace_max.nr_entries || stack_dump_trace[n] == ULONG_MAX) + if (n >= stack_trace_max.nr_entries || stack_dump_trace[n] == ULONG_MAX) return NULL;

m->private = (void *)n;

From: Wolfram Sang wsa+renesas@sang-engineering.com

[ Upstream commit e990e12741877e9bfac402ca468f4007a75f6e2a ]

The datasheet says we must stop the timer before changing the clock divider. This can happen when the restart handler is called while the watchdog is running.

Signed-off-by: Wolfram Sang wsa+renesas@sang-engineering.com Reviewed-by: Fabrizio Castro fabrizio.castro@bp.renesas.com Reviewed-by: Guenter Roeck linux@roeck-us.net Signed-off-by: Guenter Roeck linux@roeck-us.net Signed-off-by: Wim Van Sebroeck wim@linux-watchdog.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/watchdog/renesas_wdt.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/watchdog/renesas_wdt.c b/drivers/watchdog/renesas_wdt.c index 88d81feba4e6..d01efd342dc0 100644 --- a/drivers/watchdog/renesas_wdt.c +++ b/drivers/watchdog/renesas_wdt.c @@ -77,12 +77,17 @@ static int rwdt_init_timeout(struct watchdog_device *wdev) static int rwdt_start(struct watchdog_device *wdev) { struct rwdt_priv *priv = watchdog_get_drvdata(wdev); + u8 val;

pm_runtime_get_sync(wdev->parent);

- rwdt_write(priv, 0, RWTCSRB); - rwdt_write(priv, priv->cks, RWTCSRA); + /* Stop the timer before we modify any register */ + val = readb_relaxed(priv->base + RWTCSRA) & ~RWTCSRA_TME; + rwdt_write(priv, val, RWTCSRA); + rwdt_init_timeout(wdev); + rwdt_write(priv, priv->cks, RWTCSRA); + rwdt_write(priv, 0, RWTCSRB);

while (readb_relaxed(priv->base + RWTCSRA) & RWTCSRA_WRFLG) cpu_relax();

From: Tejas Joglekar tejas.joglekar@synopsys.com

[ Upstream commit 244add8ebfb231c39db9e33b204bd0ce8f24f782 ]

In stream mode, when fast-forwarding TRBs, the stream number is not cleared causing the new stream to not get assigned. So we don't want controller to carry on transfers when short packet is received. So disable the CSP for stream capable endpoint.

This is based on the 3.30a Programming guide, where table 3-1 device descriptor structure field definitions says for CSP bit If this bit is 0, the controller generates an XferComplete event and remove the stream. So if we keep CSP as 1 then switching between streams would not happen as in stream mode, when fast-forwarding TRBs, the stream number is not cleared causing the new stream to not get assigned.

Signed-off-by: Tejas Joglekar joglekar@synopsys.com Signed-off-by: Felipe Balbi felipe.balbi@linux.intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/usb/dwc3/gadget.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index a9f22a0a3462..e82be2ec859a 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -979,9 +979,13 @@ static void __dwc3_prepare_one_trb(struct dwc3_ep *dep, struct dwc3_trb *trb, usb_endpoint_type(dep->endpoint.desc)); }

- /* always enable Continue on Short Packet */ + /* + * Enable Continue on Short Packet + * when endpoint is not a stream capable + */ if (usb_endpoint_dir_out(dep->endpoint.desc)) { - trb->ctrl |= DWC3_TRB_CTRL_CSP; + if (!dep->stream_capable) + trb->ctrl |= DWC3_TRB_CTRL_CSP;

if (short_not_ok) trb->ctrl |= DWC3_TRB_CTRL_ISP_IMI;

From: Vivek Gautam vivek.gautam@codeaurora.org

[ Upstream commit 89cddc563743cb1e0068867ac97013b2a5bf86aa ]

qcom,smmu-v2 is an arm,smmu-v2 implementation with specific clock and power requirements. On msm8996, multiple cores, viz. mdss, video, etc. use this smmu. On sdm845, this smmu is used with gpu. Add bindings for the same.

Signed-off-by: Vivek Gautam vivek.gautam@codeaurora.org Reviewed-by: Rob Herring robh@kernel.org Reviewed-by: Tomasz Figa tfiga@chromium.org Tested-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org Reviewed-by: Robin Murphy robin.murphy@arm.com Signed-off-by: Will Deacon will.deacon@arm.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/iommu/arm-smmu.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/drivers/iommu/arm-smmu.c b/drivers/iommu/arm-smmu.c index e7cbf4fcf61d..ce119cb279c3 100644 --- a/drivers/iommu/arm-smmu.c +++ b/drivers/iommu/arm-smmu.c @@ -118,6 +118,7 @@ enum arm_smmu_implementation { GENERIC_SMMU, ARM_MMU500, CAVIUM_SMMUV2, + QCOM_SMMUV2, };

struct arm_smmu_s2cr { @@ -1912,6 +1913,7 @@ ARM_SMMU_MATCH_DATA(smmu_generic_v2, ARM_SMMU_V2, GENERIC_SMMU); ARM_SMMU_MATCH_DATA(arm_mmu401, ARM_SMMU_V1_64K, GENERIC_SMMU); ARM_SMMU_MATCH_DATA(arm_mmu500, ARM_SMMU_V2, ARM_MMU500); ARM_SMMU_MATCH_DATA(cavium_smmuv2, ARM_SMMU_V2, CAVIUM_SMMUV2); +ARM_SMMU_MATCH_DATA(qcom_smmuv2, ARM_SMMU_V2, QCOM_SMMUV2);

static const struct of_device_id arm_smmu_of_match[] = { { .compatible = "arm,smmu-v1", .data = &smmu_generic_v1 }, @@ -1920,6 +1922,7 @@ static const struct of_device_id arm_smmu_of_match[] = { { .compatible = "arm,mmu-401", .data = &arm_mmu401 }, { .compatible = "arm,mmu-500", .data = &arm_mmu500 }, { .compatible = "cavium,smmu-v2", .data = &cavium_smmuv2 }, + { .compatible = "qcom,smmu-v2", .data = &qcom_smmuv2 }, { }, }; MODULE_DEVICE_TABLE(of, arm_smmu_of_match);

From: Sergei Shtylyov sergei.shtylyov@cogentembedded.com

[ Upstream commit 9f83cfdb1ace3ef268ecc6fda50058d2ec37d603 ]

The driver overrides the error codes returned by platform_get_irq() to -EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe permanently instead of the deferred probing. Switch to propagating the error code upstream, still checking/overriding IRQ0 as libata regards it as "no IRQ" (thus polling) anyway...

Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Reviewed-by: Simon Horman horms+renesas@verge.net.au Reviewed-by: Geert Uytterhoeven geert+renesas@glider.be Signed-off-by: Sergei Shtylyov sergei.shtylyov@cogentembedded.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/ata/sata_rcar.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c index 10ecb232245d..03867f539f3a 100644 --- a/drivers/ata/sata_rcar.c +++ b/drivers/ata/sata_rcar.c @@ -895,7 +895,9 @@ static int sata_rcar_probe(struct platform_device *pdev) int ret = 0;

irq = platform_get_irq(pdev, 0); - if (irq <= 0) + if (irq < 0) + return irq; + if (!irq) return -EINVAL;

priv = devm_kzalloc(dev, sizeof(struct sata_rcar_priv), GFP_KERNEL);

From: Vadim Pasternak vadimp@mellanox.com

[ Upstream commit edd45cba5ed7f53974475ddc9a1453c2c87b3328 ]

Shift by one the registers for tachometers (7 - 12).

This fix is relevant for the same new systems MQMB7, MSN37, MSN34, which are about to be released to the customers. At the moment, none of them is at customers sites. The customers will not suffer from this change. This fix is necessary, because register used before for tachometer 7 has been than reserved for the second PWM for newer systems, which are not supported yet in mlx-platform driver. So registers of tachometers 7-12 have been shifted by one.

Fixes: 0378123c5800 ("platform/x86: mlx-platform: Add mlxreg-fan platform driver activation") Signed-off-by: Vadim Pasternak vadimp@mellanox.com Signed-off-by: Darren Hart (VMware) dvhart@infradead.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/platform/x86/mlx-platform.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/platform/x86/mlx-platform.c b/drivers/platform/x86/mlx-platform.c index d89936c93ba0..78b4aa4410fb 100644 --- a/drivers/platform/x86/mlx-platform.c +++ b/drivers/platform/x86/mlx-platform.c @@ -83,12 +83,12 @@ #define MLXPLAT_CPLD_LPC_REG_TACHO4_OFFSET 0xe7 #define MLXPLAT_CPLD_LPC_REG_TACHO5_OFFSET 0xe8 #define MLXPLAT_CPLD_LPC_REG_TACHO6_OFFSET 0xe9 -#define MLXPLAT_CPLD_LPC_REG_TACHO7_OFFSET 0xea -#define MLXPLAT_CPLD_LPC_REG_TACHO8_OFFSET 0xeb -#define MLXPLAT_CPLD_LPC_REG_TACHO9_OFFSET 0xec -#define MLXPLAT_CPLD_LPC_REG_TACHO10_OFFSET 0xed -#define MLXPLAT_CPLD_LPC_REG_TACHO11_OFFSET 0xee -#define MLXPLAT_CPLD_LPC_REG_TACHO12_OFFSET 0xef +#define MLXPLAT_CPLD_LPC_REG_TACHO7_OFFSET 0xeb +#define MLXPLAT_CPLD_LPC_REG_TACHO8_OFFSET 0xec +#define MLXPLAT_CPLD_LPC_REG_TACHO9_OFFSET 0xed +#define MLXPLAT_CPLD_LPC_REG_TACHO10_OFFSET 0xee +#define MLXPLAT_CPLD_LPC_REG_TACHO11_OFFSET 0xef +#define MLXPLAT_CPLD_LPC_REG_TACHO12_OFFSET 0xf0 #define MLXPLAT_CPLD_LPC_IO_RANGE 0x100 #define MLXPLAT_CPLD_LPC_I2C_CH1_OFF 0xdb #define MLXPLAT_CPLD_LPC_I2C_CH2_OFF 0xda

From: Viresh Kumar viresh.kumar@linaro.org

[ Upstream commit 90e3577b5feb42bac1269e16bb3d2bdd8f6df40f ]

The value of opp_table->regulator_count is not very consistent right now and it may end up being 0 while we do have a "opp-microvolt" property in the OPP table. It was kept that way as we used to check if any regulators are set with the OPP core for a device or not using value of regulator_count.

Lets use opp_table->regulators for that purpose as the meaning of regulator_count is going to change in the later patches.

Reported-by: Quentin Perret quentin.perret@arm.com Signed-off-by: Viresh Kumar viresh.kumar@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/opp/core.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/opp/core.c b/drivers/opp/core.c index 31ff03dbeb83..f3433bf47b10 100644 --- a/drivers/opp/core.c +++ b/drivers/opp/core.c @@ -191,12 +191,12 @@ unsigned long dev_pm_opp_get_max_volt_latency(struct device *dev) if (IS_ERR(opp_table)) return 0;

- count = opp_table->regulator_count; - /* Regulator may not be required for the device */ - if (!count) + if (!opp_table->regulators) goto put_opp_table;

+ count = opp_table->regulator_count; + uV = kmalloc_array(count, sizeof(*uV), GFP_KERNEL); if (!uV) goto put_opp_table; @@ -976,6 +976,9 @@ static bool _opp_supported_by_regulators(struct dev_pm_opp *opp, struct regulator *reg; int i;

+ if (!opp_table->regulators) + return true; + for (i = 0; i < opp_table->regulator_count; i++) { reg = opp_table->regulators[i];

@@ -1263,7 +1266,7 @@ static int _allocate_set_opp_data(struct opp_table *opp_table) struct dev_pm_set_opp_data *data; int len, count = opp_table->regulator_count;

- if (WARN_ON(!count)) + if (WARN_ON(!opp_table->regulators)) return -EINVAL;

/* space for set_opp_data */

From: Abhinav Kumar abhinavk@codeaurora.org

[ Upstream commit c1866d44d149a1ea5c303632114fb6aa08cfd263 ]

Fix the dsi clock names in the DSI 10nm PLL driver to match the names in the dispcc driver as those are according to the clock plan of the chipset.

Changes in v2: - Update the clock diagram with the new clock name

Reviewed-by: Sean Paul seanpaul@chromium.org Signed-off-by: Abhinav Kumar abhinavk@codeaurora.org Signed-off-by: Sean Paul seanpaul@chromium.org Signed-off-by: Rob Clark robdclark@gmail.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c index 41bec570c518..31205625c734 100644 --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c @@ -17,7 +17,7 @@ * | | * | | * +---------+ | +----------+ | +----+ - * dsi0vco_clk ---| out_div |--o--| divl_3_0 |--o--| /8 |-- dsi0pllbyte + * dsi0vco_clk ---| out_div |--o--| divl_3_0 |--o--| /8 |-- dsi0_phy_pll_out_byteclk * +---------+ | +----------+ | +----+ * | | * | | dsi0_pll_by_2_bit_clk @@ -25,7 +25,7 @@ * | | +----+ | |\ dsi0_pclk_mux * | |--| /2 |--o--| \ | * | | +----+ | \ | +---------+ - * | --------------| |--o--| div_7_4 |-- dsi0pll + * | --------------| |--o--| div_7_4 |-- dsi0_phy_pll_out_dsiclk * |------------------------------| / +---------+ * | +-----+ | / * -----------| /4? |--o----------|/ @@ -690,7 +690,7 @@ static int pll_10nm_register(struct dsi_pll_10nm *pll_10nm)

hws[num++] = hw;

- snprintf(clk_name, 32, "dsi%dpllbyte", pll_10nm->id); + snprintf(clk_name, 32, "dsi%d_phy_pll_out_byteclk", pll_10nm->id); snprintf(parent, 32, "dsi%d_pll_bit_clk", pll_10nm->id);

/* DSI Byte clock = VCO_CLK / OUT_DIV / BIT_DIV / 8 */ @@ -739,7 +739,7 @@ static int pll_10nm_register(struct dsi_pll_10nm *pll_10nm)

hws[num++] = hw;

- snprintf(clk_name, 32, "dsi%dpll", pll_10nm->id); + snprintf(clk_name, 32, "dsi%d_phy_pll_out_dsiclk", pll_10nm->id); snprintf(parent, 32, "dsi%d_pclk_mux", pll_10nm->id);

/* PIX CLK DIV : DIV_CTRL_7_4*/

From: Hans Holmberg hans.holmberg@cnexlabs.com

[ Upstream commit c12fa401ac8c94a74aff68bb5736b3f1dc695fa8 ]

Make sure we only look up valid lba addresses on the resubmission path.

If an lba is invalidated in the write buffer, that sector will be submitted to disk (as it is already mapped to a ppa), and that write might fail, resulting in a crash when trying to look up the lba in the mapping table (as the lba is marked as invalid).

Signed-off-by: Hans Holmberg hans.holmberg@cnexlabs.com Reviewed-by: Javier González javier@javigon.com Signed-off-by: Matias Bjørling mb@lightnvm.io Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/lightnvm/pblk-write.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/lightnvm/pblk-write.c b/drivers/lightnvm/pblk-write.c index 879227d584e7..c3e038d4b22e 100644 --- a/drivers/lightnvm/pblk-write.c +++ b/drivers/lightnvm/pblk-write.c @@ -158,9 +158,11 @@ static void pblk_prepare_resubmit(struct pblk *pblk, unsigned int sentry, w_ctx = &entry->w_ctx;

/* Check if the lba has been overwritten */ - ppa_l2p = pblk_trans_map_get(pblk, w_ctx->lba); - if (!pblk_ppa_comp(ppa_l2p, entry->cacheline)) - w_ctx->lba = ADDR_EMPTY; + if (w_ctx->lba != ADDR_EMPTY) { + ppa_l2p = pblk_trans_map_get(pblk, w_ctx->lba); + if (!pblk_ppa_comp(ppa_l2p, entry->cacheline)) + w_ctx->lba = ADDR_EMPTY; + }

/* Mark up the entry as submittable again */ flags = READ_ONCE(w_ctx->flags);

From: "Adamski, Krzysztof (Nokia - PL/Wroclaw)" krzysztof.adamski@nokia.com

[ Upstream commit 4f5c85fe3a60ace555d09898166af372547f97fc ]

It was observed that when using seqentional mode contrary to the documentation, the SS bit (which is supposed to only be set if automatic/sequence command completed normally), is sometimes set together with NA (NAK in address phase) causing transfer to falsely be considered successful.

My assumption is that this does not happen during manual mode since the controller is stopping its work the moment it sets NA/ND bit in status register. This is not the case in Automatic/Sequentional mode where it is still working to send STOP condition and the actual status we get depends on the time when the ISR is run.

This patch changes the order of checking status bits in ISR - error conditions are checked first and only if none of them occurred, the transfer may be considered successful. This is required to introduce using of sequentional mode in next patch.

Signed-off-by: Krzysztof Adamski krzysztof.adamski@nokia.com Reviewed-by: Alexander Sverdlin alexander.sverdlin@nokia.com Signed-off-by: Wolfram Sang wsa@the-dreams.de Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/i2c/busses/i2c-axxia.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/i2c/busses/i2c-axxia.c b/drivers/i2c/busses/i2c-axxia.c index 51d34959709b..fb5bac079e83 100644 --- a/drivers/i2c/busses/i2c-axxia.c +++ b/drivers/i2c/busses/i2c-axxia.c @@ -296,22 +296,7 @@ static irqreturn_t axxia_i2c_isr(int irq, void *_dev) i2c_int_disable(idev, MST_STATUS_TFL); }

- if (status & MST_STATUS_SCC) { - /* Stop completed */ - i2c_int_disable(idev, ~MST_STATUS_TSS); - complete(&idev->msg_complete); - } else if (status & MST_STATUS_SNS) { - /* Transfer done */ - i2c_int_disable(idev, ~MST_STATUS_TSS); - if (i2c_m_rd(idev->msg) && idev->msg_xfrd < idev->msg->len) - axxia_i2c_empty_rx_fifo(idev); - complete(&idev->msg_complete); - } else if (status & MST_STATUS_TSS) { - /* Transfer timeout */ - idev->msg_err = -ETIMEDOUT; - i2c_int_disable(idev, ~MST_STATUS_TSS); - complete(&idev->msg_complete); - } else if (unlikely(status & MST_STATUS_ERR)) { + if (unlikely(status & MST_STATUS_ERR)) { /* Transfer error */ i2c_int_disable(idev, ~0); if (status & MST_STATUS_AL) @@ -328,6 +313,21 @@ static irqreturn_t axxia_i2c_isr(int irq, void *_dev) readl(idev->base + MST_TX_BYTES_XFRD), readl(idev->base + MST_TX_XFER)); complete(&idev->msg_complete); + } else if (status & MST_STATUS_SCC) { + /* Stop completed */ + i2c_int_disable(idev, ~MST_STATUS_TSS); + complete(&idev->msg_complete); + } else if (status & MST_STATUS_SNS) { + /* Transfer done */ + i2c_int_disable(idev, ~MST_STATUS_TSS); + if (i2c_m_rd(idev->msg) && idev->msg_xfrd < idev->msg->len) + axxia_i2c_empty_rx_fifo(idev); + complete(&idev->msg_complete); + } else if (status & MST_STATUS_TSS) { + /* Transfer timeout */ + idev->msg_err = -ETIMEDOUT; + i2c_int_disable(idev, ~MST_STATUS_TSS); + complete(&idev->msg_complete); }

out:

From: Nir Dotan nird@mellanox.com

[ Upstream commit d7263ab35be25505ab57ebecd93cbc5dba8be717 ]

In Spectrum-2, higher priority value wins and priority valid values are in the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up until now tc flower did not provide priority 0 or reached the maximal value, however multicast routing does provide priority 0.

Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in the correct range. Make sure priority is never set to zero and never exceeds the maximal allowed value.

Signed-off-by: Nir Dotan nird@mellanox.com Reviewed-by: Jiri Pirko jiri@mellanox.com Signed-off-by: Ido Schimmel idosch@mellanox.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c index e171513bb32a..30931a2c025b 100644 --- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c +++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c @@ -95,8 +95,9 @@ int mlxsw_sp_acl_tcam_priority_get(struct mlxsw_sp *mlxsw_sp, if (!MLXSW_CORE_RES_VALID(mlxsw_sp->core, KVD_SIZE)) return -EIO;

- max_priority = MLXSW_CORE_RES_GET(mlxsw_sp->core, KVD_SIZE); - if (rulei->priority > max_priority) + /* Priority range is 1..cap_kvd_size-1. */ + max_priority = MLXSW_CORE_RES_GET(mlxsw_sp->core, KVD_SIZE) - 1; + if (rulei->priority >= max_priority) return -EINVAL;

/* Unlike in TC, in HW, higher number means higher priority. */

From: Joey Zhang joey.zhang@microchip.com

[ Upstream commit e4a7dca5de625018b29417ecc39dc5037d9a5a36 ]

In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call event_ctl() several times with the same "ctl" struct. Each call clobbers ctl.flags, which leads to the problem that we may not actually enable or disable all events as the user requested.

Preserve the event flag value with a temporary variable.

Fixes: 52eabba5bcdb ("switchtec: Add IOCTLs to the Switchtec driver") Signed-off-by: Joey Zhang joey.zhang@microchip.com Signed-off-by: Wesley Sheng wesley.sheng@microchip.com [bhelgaas: changelog] Signed-off-by: Bjorn Helgaas bhelgaas@google.com Reviewed-by: Logan Gunthorpe logang@deltatee.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pci/switch/switchtec.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/drivers/pci/switch/switchtec.c b/drivers/pci/switch/switchtec.c index 54a8b30dda38..37d0c15c9eeb 100644 --- a/drivers/pci/switch/switchtec.c +++ b/drivers/pci/switch/switchtec.c @@ -800,6 +800,7 @@ static int ioctl_event_ctl(struct switchtec_dev *stdev, { int ret; int nr_idxs; + unsigned int event_flags; struct switchtec_ioctl_event_ctl ctl;

if (copy_from_user(&ctl, uctl, sizeof(ctl))) @@ -821,7 +822,9 @@ static int ioctl_event_ctl(struct switchtec_dev *stdev, else return -EINVAL;

+ event_flags = ctl.flags; for (ctl.index = 0; ctl.index < nr_idxs; ctl.index++) { + ctl.flags = event_flags; ret = event_ctl(stdev, &ctl); if (ret < 0) return ret;

From: Arnd Bergmann arnd@arndb.de

[ Upstream commit 88af3209aa0881aa5ffd99664b6080a4be5f24e5 ]

WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info() The function littleton_init_lcd() references the function __init pxa_set_fb_info(). This is often because littleton_init_lcd lacks a __init annotation or the annotation of pxa_set_fb_info is wrong.

WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info() The function zeus_register_ohci() references the function __init pxa_set_ohci_info(). This is often because zeus_register_ohci lacks a __init annotation or the annotation of pxa_set_ohci_info is wrong.

WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info() The function cm_x300_init_u2d() references the function __init pxa3xx_set_u2d_info(). This is often because cm_x300_init_u2d lacks a __init annotation or the annotation of pxa3xx_set_u2d_info is wrong.

Signed-off-by: Arnd Bergmann arnd@arndb.de Signed-off-by: Olof Johansson olof@lixom.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-pxa/cm-x300.c | 2 +- arch/arm/mach-pxa/littleton.c | 2 +- arch/arm/mach-pxa/zeus.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c index c5c0ab8ac9f9..024c1fbcc55a 100644 --- a/arch/arm/mach-pxa/cm-x300.c +++ b/arch/arm/mach-pxa/cm-x300.c @@ -558,7 +558,7 @@ static struct pxa3xx_u2d_platform_data cm_x300_u2d_platform_data = { .exit = cm_x300_u2d_exit, };

-static void cm_x300_init_u2d(void) +static void __init cm_x300_init_u2d(void) { pxa3xx_set_u2d_info(&cm_x300_u2d_platform_data); } diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c index 9e132b3e48c6..9960ea158829 100644 --- a/arch/arm/mach-pxa/littleton.c +++ b/arch/arm/mach-pxa/littleton.c @@ -184,7 +184,7 @@ static struct pxafb_mach_info littleton_lcd_info = { .lcd_conn = LCD_COLOR_TFT_16BPP, };

-static void littleton_init_lcd(void) +static void __init littleton_init_lcd(void) { pxa_set_fb_info(NULL, &littleton_lcd_info); } diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c index e3851795d6d7..68a536de542d 100644 --- a/arch/arm/mach-pxa/zeus.c +++ b/arch/arm/mach-pxa/zeus.c @@ -559,7 +559,7 @@ static struct pxaohci_platform_data zeus_ohci_platform_data = { .flags = ENABLE_PORT_ALL | POWER_SENSE_LOW, };

-static void zeus_register_ohci(void) +static void __init zeus_register_ohci(void) { /* Port 2 is shared between host and client interface. */ UP2OCR = UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE;

From: Arnd Bergmann arnd@arndb.de

[ Upstream commit 12d3a30db4a3b3df5fbadf5974b9cf50544a9950 ]

The change to passing the timer frequency as a function argument was a good idea, but caused a build failure for one user that was missed in the update:

arch/arm/mach-mmp/time.c: In function 'mmp_dt_init_timer': arch/arm/mach-mmp/time.c:242:2: error: implicit declaration of function 'timer_init'; did you mean 'hrtimer_init'? [-Werror=implicit-function-declaration]

Change that as well to fix the build error, and rename the function to put it into a proper namespace and make it clearer what is actually going on.

I saw that the high 6500000 HZ frequency was previously only set with CONFIG_MMP2, but is now also used with MMP (pxa910), so I'm changing that back here. Please make sure that the frequencies are all correct now.

Fixes: f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock") Signed-off-by: Arnd Bergmann arnd@arndb.de Signed-off-by: Olof Johansson olof@lixom.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-mmp/common.h | 2 +- arch/arm/mach-mmp/mmp2.c | 2 +- arch/arm/mach-mmp/pxa168.c | 2 +- arch/arm/mach-mmp/pxa910.c | 2 +- arch/arm/mach-mmp/time.c | 4 ++-- 5 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-mmp/common.h b/arch/arm/mach-mmp/common.h index 5ac2851ef5d3..483b8b6d3005 100644 --- a/arch/arm/mach-mmp/common.h +++ b/arch/arm/mach-mmp/common.h @@ -2,7 +2,7 @@ #include <linux/reboot.h> #define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)

-extern void timer_init(int irq, unsigned long rate); +extern void mmp_timer_init(int irq, unsigned long rate);

extern void __init mmp_map_io(void); extern void mmp_restart(enum reboot_mode, const char *); diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c index fb3e7e32c882..726c1a642dea 100644 --- a/arch/arm/mach-mmp/mmp2.c +++ b/arch/arm/mach-mmp/mmp2.c @@ -134,7 +134,7 @@ void __init mmp2_timer_init(void) clk_rst = APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1); __raw_writel(clk_rst, APBC_TIMERS);

- timer_init(IRQ_MMP2_TIMER1, 6500000); + mmp_timer_init(IRQ_MMP2_TIMER1, 6500000); }

/* on-chip devices */ diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c index 77a358165a56..cdcf65ace3f9 100644 --- a/arch/arm/mach-mmp/pxa168.c +++ b/arch/arm/mach-mmp/pxa168.c @@ -79,7 +79,7 @@ void __init pxa168_timer_init(void) /* 3.25MHz, bus/functional clock enabled, release reset */ __raw_writel(TIMER_CLK_RST, APBC_TIMERS);

- timer_init(IRQ_PXA168_TIMER1, 6500000); + mmp_timer_init(IRQ_PXA168_TIMER1, 3250000); }

void pxa168_clear_keypad_wakeup(void) diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c index 1ccbba9ac495..d30a7d12bc98 100644 --- a/arch/arm/mach-mmp/pxa910.c +++ b/arch/arm/mach-mmp/pxa910.c @@ -116,7 +116,7 @@ void __init pxa910_timer_init(void) __raw_writel(APBC_APBCLK | APBC_RST, APBC_TIMERS); __raw_writel(TIMER_CLK_RST, APBC_TIMERS);

- timer_init(IRQ_PXA910_AP1_TIMER1); + mmp_timer_init(IRQ_PXA910_AP1_TIMER1, 3250000); }

/* on-chip devices */ diff --git a/arch/arm/mach-mmp/time.c b/arch/arm/mach-mmp/time.c index eab0fd8a7343..f9c295154b94 100644 --- a/arch/arm/mach-mmp/time.c +++ b/arch/arm/mach-mmp/time.c @@ -184,7 +184,7 @@ static struct irqaction timer_irq = { .dev_id = &ckevt, };

-void __init timer_init(int irq, unsigned long rate) +void __init mmp_timer_init(int irq, unsigned long rate) { timer_config();

@@ -239,7 +239,7 @@ void __init mmp_dt_init_timer(void) ret = -ENOMEM; goto out; } - timer_init(irq, rate); + mmp_timer_init(irq, rate); return; out: pr_err("Failed to get timer from device tree with error:%d\n", ret);

From: Phil Elwell phil@raspberrypi.org

[ Upstream commit 07d405769afea5718529fc9e341f0b13b3189b6f ]

If the user issues an "mmc extcsd read", the SD controller receives what it thinks is a SEND_IF_COND command with an unexpected data block. The resulting operations leave the FSM stuck in READWAIT, a state which persists until the MMC framework resets the controller, by which point the root filesystem is likely to have been unmounted.

A less heavyweight solution is to detect the condition and nudge the FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.

Link: https://github.com/raspberrypi/linux/issues/2728 Signed-off-by: Phil Elwell phil@raspberrypi.org Signed-off-by: Stefan Wahren stefan.wahren@i2se.com Acked-by: Eric Anholt eric@anholt.net Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mmc/host/bcm2835.c | 9 +++++++++ 1 file changed, 9 insertions(+)

diff --git a/drivers/mmc/host/bcm2835.c b/drivers/mmc/host/bcm2835.c index 768972af8b85..aef40e1739ee 100644 --- a/drivers/mmc/host/bcm2835.c +++ b/drivers/mmc/host/bcm2835.c @@ -772,6 +772,8 @@ static void bcm2835_finish_command(struct bcm2835_host *host)

if (!(sdhsts & SDHSTS_CRC7_ERROR) || (host->cmd->opcode != MMC_SEND_OP_COND)) { + u32 edm, fsm; + if (sdhsts & SDHSTS_CMD_TIME_OUT) { host->cmd->error = -ETIMEDOUT; } else { @@ -780,6 +782,13 @@ static void bcm2835_finish_command(struct bcm2835_host *host) bcm2835_dumpregs(host); host->cmd->error = -EILSEQ; } + edm = readl(host->ioaddr + SDEDM); + fsm = edm & SDEDM_FSM_MASK; + if (fsm == SDEDM_FSM_READWAIT || + fsm == SDEDM_FSM_WRITESTART1) + /* Kick the FSM out of its wait */ + writel(edm | SDEDM_FORCE_DATA_MODE, + host->ioaddr + SDEDM); bcm2835_finish_request(host); return; }

From: Nicholas Mc Guire hofrat@osadl.org

[ Upstream commit b0d06f1cb0e2079a3c64fb6e27c19d9a55c723a1 ]

devm_kasprintf() may return NULL on failure of internal allocation thus the assignments to init.name are not safe if not checked. On error meson_mx_mmc_register_clks() returns negative values so -ENOMEM in the (unlikely) failure case of devm_kasprintf() should be fine here.

Signed-off-by: Nicholas Mc Guire hofrat@osadl.org Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs") Acked-by: Martin Blumenstingl martin.blumenstingl@googlemail.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mmc/host/meson-mx-sdio.c | 6 ++++++ 1 file changed, 6 insertions(+)

diff --git a/drivers/mmc/host/meson-mx-sdio.c b/drivers/mmc/host/meson-mx-sdio.c index 2cfec33178c1..9841b447ccde 100644 --- a/drivers/mmc/host/meson-mx-sdio.c +++ b/drivers/mmc/host/meson-mx-sdio.c @@ -596,6 +596,9 @@ static int meson_mx_mmc_register_clks(struct meson_mx_mmc_host *host) init.name = devm_kasprintf(host->controller_dev, GFP_KERNEL, "%s#fixed_factor", dev_name(host->controller_dev)); + if (!init.name) + return -ENOMEM; + init.ops = &clk_fixed_factor_ops; init.flags = 0; init.parent_names = &clk_fixed_factor_parent; @@ -612,6 +615,9 @@ static int meson_mx_mmc_register_clks(struct meson_mx_mmc_host *host) clk_div_parent = __clk_get_name(host->fixed_factor_clk); init.name = devm_kasprintf(host->controller_dev, GFP_KERNEL, "%s#div", dev_name(host->controller_dev)); + if (!init.name) + return -ENOMEM; + init.ops = &clk_divider_ops; init.flags = CLK_SET_RATE_PARENT; init.parent_names = &clk_div_parent;

From: Adrian Hunter adrian.hunter@intel.com

[ Upstream commit ea6d027312111c6d96309ad1a684b33cb37e6764 ]

Always check the wait condition before returning timeout.

Signed-off-by: Adrian Hunter adrian.hunter@intel.com Reviewed-by: Yangbo Lu yangbo.lu@nxp.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mmc/host/sdhci-of-esdhc.c | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c index 9cb7554a463d..a7bf8515116f 100644 --- a/drivers/mmc/host/sdhci-of-esdhc.c +++ b/drivers/mmc/host/sdhci-of-esdhc.c @@ -526,8 +526,12 @@ static void esdhc_clock_enable(struct sdhci_host *host, bool enable) /* Wait max 20 ms */ timeout = ktime_add_ms(ktime_get(), 20); val = ESDHC_CLOCK_STABLE; - while (!(sdhci_readl(host, ESDHC_PRSSTAT) & val)) { - if (ktime_after(ktime_get(), timeout)) { + while (1) { + bool timedout = ktime_after(ktime_get(), timeout); + + if (sdhci_readl(host, ESDHC_PRSSTAT) & val) + break; + if (timedout) { pr_err("%s: Internal clock never stabilised.\n", mmc_hostname(host->mmc)); break; @@ -591,8 +595,12 @@ static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock)

/* Wait max 20 ms */ timeout = ktime_add_ms(ktime_get(), 20); - while (!(sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE)) { - if (ktime_after(ktime_get(), timeout)) { + while (1) { + bool timedout = ktime_after(ktime_get(), timeout); + + if (sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE) + break; + if (timedout) { pr_err("%s: Internal clock never stabilised.\n", mmc_hostname(host->mmc)); return;

From: Adrian Hunter adrian.hunter@intel.com

[ Upstream commit 0e6e7c2ff397e1bbebc882ca3132148aaaef1ddd ]