[PATCH AUTOSEL 5.15 01/29] ARM: dts: imx6qp-prtwd3: update RGMII delays for sja1105 switch
From: Vladimir Oltean vladimir.oltean@nxp.com
[ Upstream commit f2c2e9ebb2cf476c09e59d073db031fbf7ef4914 ]
In the new behavior, the sja1105 driver expects there to be explicit RGMII delays present on the fixed-link ports, otherwise it will complain that it falls back to legacy behavior, which is to apply RGMII delays incorrectly derived from the phy-mode string.
In this case, the legacy behavior of the driver is to apply both RX and TX delays. To preserve that, add explicit 2 nanosecond delays, which are identical with what the driver used to add (a 90 degree phase shift). The delays from the phy-mode are ignored by new kernels (it's still RGMII as long as it's "rgmii*" something), and the explicit {rx,tx}-internal-delay-ps properties are ignored by old kernels, so the change works both ways.
Signed-off-by: Vladimir Oltean vladimir.oltean@nxp.com Reviewed-by: Florian Fainelli f.fainelli@gmail.com Reviewed-by: Oleksij Rempel o.rempel@pengutronix.de Signed-off-by: Shawn Guo shawnguo@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/imx6qp-prtwd3.dts | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qp-prtwd3.dts b/arch/arm/boot/dts/imx6qp-prtwd3.dts index b92e0f2748a51..29dd59bfa73dd 100644 --- a/arch/arm/boot/dts/imx6qp-prtwd3.dts +++ b/arch/arm/boot/dts/imx6qp-prtwd3.dts @@ -178,6 +178,8 @@ port@4 { label = "cpu"; ethernet = <&fec>; phy-mode = "rgmii-id"; + rx-internal-delay-ps = <2000>; + tx-internal-delay-ps = <2000>;
fixed-link { speed = <100>;
From: Vladimir Oltean vladimir.oltean@nxp.com
[ Upstream commit e691f9282a89e24a8e87cdb91a181c6283ee5124 ]
In the new behavior, the sja1105 driver expects there to be explicit RGMII delays present on the fixed-link ports, otherwise it will complain that it falls back to legacy behavior, which is to apply RGMII delays incorrectly derived from the phy-mode string.
In this case, the legacy behavior of the driver is to not apply delays in any direction (mostly because the SJA1105T can't do that, so this board uses PCB traces). To preserve that but also silence the driver, use explicit delays of 0 ns. The delay information from the phy-mode is ignored by new kernels (it's still RGMII as long as it's "rgmii*" something), and the explicit {rx,tx}-internal-delay-ps properties are ignored by old kernels, so the change works both ways.
Signed-off-by: Vladimir Oltean vladimir.oltean@nxp.com Reviewed-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: Shawn Guo shawnguo@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/ls1021a-tsn.dts | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts index aca78b5eddf20..194748737724c 100644 --- a/arch/arm/boot/dts/ls1021a-tsn.dts +++ b/arch/arm/boot/dts/ls1021a-tsn.dts @@ -90,6 +90,8 @@ port@4 { /* Internal port connected to eth2 */ ethernet = <&enet2>; phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; reg = <4>;
fixed-link {
From: "Ivan T. Ivanov" iivanov@suse.de
[ Upstream commit 423e85e97aaf69e5198bbec6811e3825c8b5019a ]
This fixes a potential kernel panic on memcpy when FORTIFY_SOURCE is enabled. Because memory is iomem use appropriate function for accessing it.
Signed-off-by: Ivan T. Ivanov iivanov@suse.de Link: https://lore.kernel.org/r/20211116084616.24811-1-iivanov@suse.de Signed-off-by: Heiko Stuebner heiko@sntech.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/mach-rockchip/platsmp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-rockchip/platsmp.c b/arch/arm/mach-rockchip/platsmp.c index d60856898d97a..5ec58d004b7de 100644 --- a/arch/arm/mach-rockchip/platsmp.c +++ b/arch/arm/mach-rockchip/platsmp.c @@ -189,7 +189,7 @@ static int __init rockchip_smp_prepare_sram(struct device_node *node) rockchip_boot_fn = __pa_symbol(secondary_startup);
/* copy the trampoline to sram, that runs during startup of the core */ - memcpy(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz); + memcpy_toio(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz); flush_cache_all(); outer_clean_range(0, trampoline_sz);
From: Maxime Bizon mbizon@freebox.fr
[ Upstream commit 48c06708e63e71b4395e4159797366aa03be10ff ]
sta is NULL for mesh point (resolved later), so sk pacing parameters were not applied.
Signed-off-by: Maxime Bizon mbizon@freebox.fr Link: https://lore.kernel.org/r/66f51659416ac35d6b11a313bd3ffe8b8a43dd55.camel@fre... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/tx.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c index 0527bf41a32c7..0613b3ab523a5 100644 --- a/net/mac80211/tx.c +++ b/net/mac80211/tx.c @@ -4190,11 +4190,11 @@ void __ieee80211_subif_start_xmit(struct sk_buff *skb,
ieee80211_aggr_check(sdata, sta, skb);
+ sk_pacing_shift_update(skb->sk, sdata->local->hw.tx_sk_pacing_shift); + if (sta) { struct ieee80211_fast_tx *fast_tx;
- sk_pacing_shift_update(skb->sk, sdata->local->hw.tx_sk_pacing_shift); - fast_tx = rcu_dereference(sta->fast_tx);
if (fast_tx &&
From: Xing Song xing.song@mediatek.com
[ Upstream commit 942bd1070c3a39d1302fc5db73d60c86e3033c81 ]
Mesh forwarding requires that the fwd_skb->dev is set up for TX handling, otherwise the following warning will be generated, so set it up for the pending frames.
[ 72.835674 ] WARNING: CPU: 0 PID: 1193 at __skb_flow_dissect+0x284/0x1298 [ 72.842379 ] Modules linked in: ksmbd pppoe ppp_async l2tp_ppp ... [ 72.962020 ] CPU: 0 PID: 1193 Comm: kworker/u5:1 Tainted: P S 5.4.137 #0 [ 72.969938 ] Hardware name: MT7622_MT7531 RFB (DT) [ 72.974659 ] Workqueue: napi_workq napi_workfn [ 72.979025 ] pstate: 60000005 (nZCv daif -PAN -UAO) [ 72.983822 ] pc : __skb_flow_dissect+0x284/0x1298 [ 72.988444 ] lr : __skb_flow_dissect+0x54/0x1298 [ 72.992977 ] sp : ffffffc010c738c0 [ 72.996293 ] x29: ffffffc010c738c0 x28: 0000000000000000 [ 73.001615 ] x27: 000000000000ffc2 x26: ffffff800c2eb818 [ 73.006937 ] x25: ffffffc010a987c8 x24: 00000000000000ce [ 73.012259 ] x23: ffffffc010c73a28 x22: ffffffc010a99c60 [ 73.017581 ] x21: 000000000000ffc2 x20: ffffff80094da800 [ 73.022903 ] x19: 0000000000000000 x18: 0000000000000014 [ 73.028226 ] x17: 00000000084d16af x16: 00000000d1fc0bab [ 73.033548 ] x15: 00000000715f6034 x14: 000000009dbdd301 [ 73.038870 ] x13: 00000000ea4dcbc3 x12: 0000000000000040 [ 73.044192 ] x11: 000000000eb00ff0 x10: 0000000000000000 [ 73.049513 ] x9 : 000000000eb00073 x8 : 0000000000000088 [ 73.054834 ] x7 : 0000000000000000 x6 : 0000000000000001 [ 73.060155 ] x5 : 0000000000000000 x4 : 0000000000000000 [ 73.065476 ] x3 : ffffffc010a98000 x2 : 0000000000000000 [ 73.070797 ] x1 : 0000000000000000 x0 : 0000000000000000 [ 73.076120 ] Call trace: [ 73.078572 ] __skb_flow_dissect+0x284/0x1298 [ 73.082846 ] __skb_get_hash+0x7c/0x228 [ 73.086629 ] ieee80211_txq_may_transmit+0x7fc/0x17b8 [mac80211] [ 73.092564 ] ieee80211_tx_prepare_skb+0x20c/0x268 [mac80211] [ 73.098238 ] ieee80211_tx_pending+0x144/0x330 [mac80211] [ 73.103560 ] tasklet_action_common.isra.16+0xb4/0x158 [ 73.108618 ] tasklet_action+0x2c/0x38 [ 73.112286 ] __do_softirq+0x168/0x3b0 [ 73.115954 ] do_softirq.part.15+0x88/0x98 [ 73.119969 ] __local_bh_enable_ip+0xb0/0xb8 [ 73.124156 ] napi_workfn+0x58/0x90 [ 73.127565 ] process_one_work+0x20c/0x478 [ 73.131579 ] worker_thread+0x50/0x4f0 [ 73.135249 ] kthread+0x124/0x128 [ 73.138484 ] ret_from_fork+0x10/0x1c
Signed-off-by: Xing Song xing.song@mediatek.com Tested-By: Frank Wunderlich frank-w@public-files.de Link: https://lore.kernel.org/r/20211123033123.2684-1-xing.song@mediatek.com Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/rx.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c index 1958e4d59b524..c41c704dcf8b7 100644 --- a/net/mac80211/rx.c +++ b/net/mac80211/rx.c @@ -2944,6 +2944,7 @@ ieee80211_rx_h_mesh_fwding(struct ieee80211_rx_data *rx) if (!fwd_skb) goto out;
+ fwd_skb->dev = sdata->dev; fwd_hdr = (struct ieee80211_hdr *) fwd_skb->data; fwd_hdr->frame_control &= ~cpu_to_le16(IEEE80211_FCTL_RETRY); info = IEEE80211_SKB_CB(fwd_skb);
From: Ahmed Zaki anzaki@gmail.com
[ Upstream commit 8f9dcc29566626f683843ccac6113a12208315ca ]
The following is from a system that went OOM due to a memory leak:
wlan0: Allocated STA 74:83:c2:64:0b:87 wlan0: Allocated STA 74:83:c2:64:0b:87 wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_add_sta) wlan0: Adding new IBSS station 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 3 wlan0: Inserted STA 74:83:c2:64:0b:87 wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_work) wlan0: Adding new IBSS station 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 3 . . wlan0: expiring inactive not authorized STA 74:83:c2:64:0b:87 wlan0: moving STA 74:83:c2:64:0b:87 to state 2 wlan0: moving STA 74:83:c2:64:0b:87 to state 1 wlan0: Removed STA 74:83:c2:64:0b:87 wlan0: Destroyed STA 74:83:c2:64:0b:87
The ieee80211_ibss_finish_sta() is called twice on the same STA from 2 different locations. On the second attempt, the allocated STA is not destroyed creating a kernel memory leak.
This is happening because sta_info_insert_finish() does not call sta_info_free() the second time when the STA already exists (returns -EEXIST). Note that the caller sta_info_insert_rcu() assumes STA is destroyed upon errors.
Same fix is applied to -ENOMEM.
Signed-off-by: Ahmed Zaki anzaki@gmail.com Link: https://lore.kernel.org/r/20211002145329.3125293-1-anzaki@gmail.com [change the error path label to use the existing code] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/sta_info.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/net/mac80211/sta_info.c b/net/mac80211/sta_info.c index 2b5acb37587f7..6eeef7a61927b 100644 --- a/net/mac80211/sta_info.c +++ b/net/mac80211/sta_info.c @@ -641,13 +641,13 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU) /* check if STA exists already */ if (sta_info_get_bss(sdata, sta->sta.addr)) { err = -EEXIST; - goto out_err; + goto out_cleanup; }
sinfo = kzalloc(sizeof(struct station_info), GFP_KERNEL); if (!sinfo) { err = -ENOMEM; - goto out_err; + goto out_cleanup; }
local->num_sta++; @@ -703,8 +703,8 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU) out_drop_sta: local->num_sta--; synchronize_net(); + out_cleanup: cleanup_single_sta(sta); - out_err: mutex_unlock(&local->sta_mtx); kfree(sinfo); rcu_read_lock();
From: Finn Behrens me@kloenk.dev
[ Upstream commit 1eda919126b420fee6b8d546f7f728fbbd4b8f11 ]
Reload the regdom when the regulatory db is reloaded. Otherwise, the user had to change the regulatoy domain to a different one and then reset it to the correct one to have a new regulatory db take effect after a reload.
Signed-off-by: Finn Behrens fin@nyantec.com Link: https://lore.kernel.org/r/YaIIZfxHgqc/UTA7@gimli.kloenk.dev [edit commit message] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- include/net/regulatory.h | 1 + net/wireless/reg.c | 27 +++++++++++++++++++++++++-- 2 files changed, 26 insertions(+), 2 deletions(-)
diff --git a/include/net/regulatory.h b/include/net/regulatory.h index 47f06f6f5a67c..0cf9335431e07 100644 --- a/include/net/regulatory.h +++ b/include/net/regulatory.h @@ -83,6 +83,7 @@ struct regulatory_request { enum nl80211_dfs_regions dfs_region; bool intersect; bool processed; + bool reload; enum environment_cap country_ie_env; struct list_head list; }; diff --git a/net/wireless/reg.c b/net/wireless/reg.c index df87c7f3a0492..61f1bf1bc4a73 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -133,6 +133,7 @@ static u32 reg_is_indoor_portid;
static void restore_regulatory_settings(bool reset_user, bool cached); static void print_regdomain(const struct ieee80211_regdomain *rd); +static void reg_process_hint(struct regulatory_request *reg_request);
static const struct ieee80211_regdomain *get_cfg80211_regdom(void) { @@ -1098,6 +1099,8 @@ int reg_reload_regdb(void) const struct firmware *fw; void *db; int err; + const struct ieee80211_regdomain *current_regdomain; + struct regulatory_request *request;
err = request_firmware(&fw, "regulatory.db", ®_pdev->dev); if (err) @@ -1118,8 +1121,27 @@ int reg_reload_regdb(void) if (!IS_ERR_OR_NULL(regdb)) kfree(regdb); regdb = db; - rtnl_unlock();
+ /* reset regulatory domain */ + current_regdomain = get_cfg80211_regdom(); + + request = kzalloc(sizeof(*request), GFP_KERNEL); + if (!request) { + err = -ENOMEM; + goto out_unlock; + } + + request->wiphy_idx = WIPHY_IDX_INVALID; + request->alpha2[0] = current_regdomain->alpha2[0]; + request->alpha2[1] = current_regdomain->alpha2[1]; + request->initiator = NL80211_USER_REG_HINT_USER; + request->user_reg_hint_type = NL80211_USER_REG_HINT_USER; + request->reload = true; + + reg_process_hint(request); + +out_unlock: + rtnl_unlock(); out: release_firmware(fw); return err; @@ -2690,7 +2712,8 @@ reg_process_hint_user(struct regulatory_request *user_request)
treatment = __reg_process_hint_user(user_request); if (treatment == REG_REQ_IGNORE || - treatment == REG_REQ_ALREADY_SET) + (treatment == REG_REQ_ALREADY_SET && + !user_request->reload)) return REG_REQ_IGNORE;
user_request->intersect = treatment == REG_REQ_INTERSECT;
On Tue, Dec 21, 2021 at 2:58 AM Sasha Levin sashal@kernel.org wrote:
From: Finn Behrens me@kloenk.dev
[ Upstream commit 1eda919126b420fee6b8d546f7f728fbbd4b8f11 ]
Reload the regdom when the regulatory db is reloaded. Otherwise, the user had to change the regulatoy domain to a different one and then reset it to the correct one to have a new regulatory db take effect after a reload.
Signed-off-by: Finn Behrens fin@nyantec.com Link: https://lore.kernel.org/r/YaIIZfxHgqc/UTA7@gimli.kloenk.dev [edit commit message] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org
This requires [1] to fix this warning:
net/wireless/reg.c:1137:23: warning: implicit conversion from enumeration type 'enum nl80211_user_reg_hint_type' to different enumeration type 'enum nl80211_reg_ initiator' [-Wenum-conversion]
[PATCH] nl80211: remove reload flag from regulatory_request
- Sedat -
[1] https://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211.git/patch/?id...
include/net/regulatory.h | 1 + net/wireless/reg.c | 27 +++++++++++++++++++++++++-- 2 files changed, 26 insertions(+), 2 deletions(-)
diff --git a/include/net/regulatory.h b/include/net/regulatory.h index 47f06f6f5a67c..0cf9335431e07 100644 --- a/include/net/regulatory.h +++ b/include/net/regulatory.h @@ -83,6 +83,7 @@ struct regulatory_request { enum nl80211_dfs_regions dfs_region; bool intersect; bool processed;
bool reload; enum environment_cap country_ie_env; struct list_head list;}; diff --git a/net/wireless/reg.c b/net/wireless/reg.c index df87c7f3a0492..61f1bf1bc4a73 100644 --- a/net/wireless/reg.c +++ b/net/wireless/reg.c @@ -133,6 +133,7 @@ static u32 reg_is_indoor_portid;
static void restore_regulatory_settings(bool reset_user, bool cached); static void print_regdomain(const struct ieee80211_regdomain *rd); +static void reg_process_hint(struct regulatory_request *reg_request);
static const struct ieee80211_regdomain *get_cfg80211_regdom(void) { @@ -1098,6 +1099,8 @@ int reg_reload_regdb(void) const struct firmware *fw; void *db; int err;
const struct ieee80211_regdomain *current_regdomain;struct regulatory_request *request; err = request_firmware(&fw, "regulatory.db", ®_pdev->dev); if (err)@@ -1118,8 +1121,27 @@ int reg_reload_regdb(void) if (!IS_ERR_OR_NULL(regdb)) kfree(regdb); regdb = db;
rtnl_unlock();
/* reset regulatory domain */current_regdomain = get_cfg80211_regdom();request = kzalloc(sizeof(*request), GFP_KERNEL);if (!request) {err = -ENOMEM;goto out_unlock;}request->wiphy_idx = WIPHY_IDX_INVALID;request->alpha2[0] = current_regdomain->alpha2[0];request->alpha2[1] = current_regdomain->alpha2[1];request->initiator = NL80211_USER_REG_HINT_USER;request->user_reg_hint_type = NL80211_USER_REG_HINT_USER;request->reload = true;reg_process_hint(request);+out_unlock:
rtnl_unlock();@@ -2690,7 +2712,8 @@ reg_process_hint_user(struct regulatory_request *user_request)
treatment = __reg_process_hint_user(user_request); if (treatment == REG_REQ_IGNORE ||
treatment == REG_REQ_ALREADY_SET)
(treatment == REG_REQ_ALREADY_SET &&!user_request->reload)) return REG_REQ_IGNORE; user_request->intersect = treatment == REG_REQ_INTERSECT;-- 2.34.1
From: Arnd Bergmann arnd@arndb.de
[ Upstream commit efdbfa0ad03e764419378485d1b8f6e7706fb1a3 ]
The dependencies for LED configuration are highly inconsistent and too complicated at the moment. One of the results is a randconfig failure I get very rarely when LEDS_CLASS is in a loadable module, but the wireless core is built-in:
WARNING: unmet direct dependencies detected for MAC80211_LEDS Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y]) Selected by [m]: - IWLEGACY [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y] - IWLWIFI_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y] && IWLWIFI [=m] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=IWLWIFI [=m]) && (IWLMVM [=m] || IWLDVM [=m])
aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_register_led': led.c:(.text+0x60): undefined reference to `led_classdev_register_ext' aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_unregister_leds': led.c:(.text+0x200): undefined reference to `led_classdev_unregister'
For iwlwifi, the dependency is wrong, since this config prevents the MAC80211_LEDS code from being part of a built-in MAC80211 driver.
For iwlegacy, this is worse because the driver tries to force-enable the other subsystems, which is both a layering violation and a bug because it will still fail with MAC80211=y and IWLEGACY=m, leading to LEDS_CLASS being a module as well.
The actual link failure in the ath5k driver is a result of MAC80211_LEDS being enabled but not usable. With the Kconfig logic fixed in the Intel drivers, the ath5k driver works as expected again.
Signed-off-by: Arnd Bergmann arnd@arndb.de Acked-by: Luca Coelho luciano.coelho@intel.com Signed-off-by: Kalle Valo kvalo@kernel.org Link: https://lore.kernel.org/r/20211204173848.873293-1-arnd@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/intel/iwlegacy/Kconfig | 4 ++-- drivers/net/wireless/intel/iwlwifi/Kconfig | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/intel/iwlegacy/Kconfig b/drivers/net/wireless/intel/iwlegacy/Kconfig index 24fe3f63c3215..7eacc8e58ee14 100644 --- a/drivers/net/wireless/intel/iwlegacy/Kconfig +++ b/drivers/net/wireless/intel/iwlegacy/Kconfig @@ -2,14 +2,13 @@ config IWLEGACY tristate select FW_LOADER - select NEW_LEDS - select LEDS_CLASS select LEDS_TRIGGERS select MAC80211_LEDS
config IWL4965 tristate "Intel Wireless WiFi 4965AGN (iwl4965)" depends on PCI && MAC80211 + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 select IWLEGACY help This option enables support for @@ -38,6 +37,7 @@ config IWL4965 config IWL3945 tristate "Intel PRO/Wireless 3945ABG/BG Network Connection (iwl3945)" depends on PCI && MAC80211 + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 select IWLEGACY help Select to build the driver supporting the: diff --git a/drivers/net/wireless/intel/iwlwifi/Kconfig b/drivers/net/wireless/intel/iwlwifi/Kconfig index 1085afbefba87..418ae4f870ab7 100644 --- a/drivers/net/wireless/intel/iwlwifi/Kconfig +++ b/drivers/net/wireless/intel/iwlwifi/Kconfig @@ -47,7 +47,7 @@ if IWLWIFI
config IWLWIFI_LEDS bool - depends on LEDS_CLASS=y || LEDS_CLASS=IWLWIFI + depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211 depends on IWLMVM || IWLDVM select LEDS_TRIGGERS select MAC80211_LEDS
From: Hangyu Hua hbh25y@gmail.com
[ Upstream commit bcd0f93353326954817a4f9fa55ec57fb38acbb0 ]
sock_hold(sk) is invoked in pep_sock_accept(), but __sock_put(sk) is not invoked in subsequent failure branches(pep_accept_conn() != 0).
Signed-off-by: Hangyu Hua hbh25y@gmail.com Link: https://lore.kernel.org/r/20211209082839.33985-1-hbh25y@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/phonet/pep.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/net/phonet/pep.c b/net/phonet/pep.c index a1525916885ae..b4f90afb0638b 100644 --- a/net/phonet/pep.c +++ b/net/phonet/pep.c @@ -868,6 +868,7 @@ static struct sock *pep_sock_accept(struct sock *sk, int flags, int *errp,
err = pep_accept_conn(newsk, skb); if (err) { + __sock_put(sk); sock_put(newsk); newsk = NULL; goto drop;
From: Daniele Palmas dnlplm@gmail.com
[ Upstream commit 94f2a444f28a649926c410eb9a38afb13a83ebe0 ]
Add the following Telit FN990 composition:
0x1070: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Daniele Palmas dnlplm@gmail.com Acked-by: Bjørn Mork bjorn@mork.no Link: https://lore.kernel.org/r/20211210095722.22269-1-dnlplm@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/qmi_wwan.c | 1 + 1 file changed, 1 insertion(+)
diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c index 33ada2c59952e..b62489f567e48 100644 --- a/drivers/net/usb/qmi_wwan.c +++ b/drivers/net/usb/qmi_wwan.c @@ -1355,6 +1355,7 @@ static const struct usb_device_id products[] = { {QMI_QUIRK_SET_DTR(0x1bc7, 0x1040, 2)}, /* Telit LE922A */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1050, 2)}, /* Telit FN980 */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1060, 2)}, /* Telit LN920 */ + {QMI_QUIRK_SET_DTR(0x1bc7, 0x1070, 2)}, /* Telit FN990 */ {QMI_FIXED_INTF(0x1bc7, 0x1100, 3)}, /* Telit ME910 */ {QMI_FIXED_INTF(0x1bc7, 0x1101, 3)}, /* Telit ME910 dual modem */ {QMI_FIXED_INTF(0x1bc7, 0x1200, 5)}, /* Telit LE920 */
From: Vignesh Raghavendra vigneshr@ti.com
[ Upstream commit 80936d68665be88dc3bf60884a71f2694eb6b1f1 ]
Smatch reports below warnings [1] wrt dereferencing rm_res when it can potentially be ERR_PTR(). This is possible when entire range is allocated to Linux Fix this case by making sure, there is no deference of rm_res when its ERR_PTR().
[1]: drivers/dma/ti/k3-udma.c:4524 udma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4537 udma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4681 bcdma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4696 bcdma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4711 bcdma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4848 pktdma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR() drivers/dma/ti/k3-udma.c:4861 pktdma_setup_resources() error: 'rm_res' dereferencing possible ERR_PTR()
Reported-by: Nishanth Menon nm@ti.com Signed-off-by: Vignesh Raghavendra vigneshr@ti.com Acked-by: Peter Ujfalusi peter.ujfalusi@gmail.com Link: https://lore.kernel.org/r/20211209180957.29036-1-vigneshr@ti.com Signed-off-by: Vinod Koul vkoul@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/dma/ti/k3-udma.c | 157 ++++++++++++++++++++++++++------------- 1 file changed, 107 insertions(+), 50 deletions(-)
diff --git a/drivers/dma/ti/k3-udma.c b/drivers/dma/ti/k3-udma.c index 041d8e32d6300..6e56d1cef5eee 100644 --- a/drivers/dma/ti/k3-udma.c +++ b/drivers/dma/ti/k3-udma.c @@ -4534,45 +4534,60 @@ static int udma_setup_resources(struct udma_dev *ud) rm_res = tisci_rm->rm_ranges[RM_RANGE_TCHAN]; if (IS_ERR(rm_res)) { bitmap_zero(ud->tchan_map, ud->tchan_cnt); + irq_res.sets = 1; } else { bitmap_fill(ud->tchan_map, ud->tchan_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->tchan_map, &rm_res->desc[i], "tchan"); + irq_res.sets = rm_res->sets; } - irq_res.sets = rm_res->sets;
/* rchan and matching default flow ranges */ rm_res = tisci_rm->rm_ranges[RM_RANGE_RCHAN]; if (IS_ERR(rm_res)) { bitmap_zero(ud->rchan_map, ud->rchan_cnt); + irq_res.sets++; } else { bitmap_fill(ud->rchan_map, ud->rchan_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->rchan_map, &rm_res->desc[i], "rchan"); + irq_res.sets += rm_res->sets; }
- irq_res.sets += rm_res->sets; irq_res.desc = kcalloc(irq_res.sets, sizeof(*irq_res.desc), GFP_KERNEL); + if (!irq_res.desc) + return -ENOMEM; rm_res = tisci_rm->rm_ranges[RM_RANGE_TCHAN]; - for (i = 0; i < rm_res->sets; i++) { - irq_res.desc[i].start = rm_res->desc[i].start; - irq_res.desc[i].num = rm_res->desc[i].num; - irq_res.desc[i].start_sec = rm_res->desc[i].start_sec; - irq_res.desc[i].num_sec = rm_res->desc[i].num_sec; + if (IS_ERR(rm_res)) { + irq_res.desc[0].start = 0; + irq_res.desc[0].num = ud->tchan_cnt; + i = 1; + } else { + for (i = 0; i < rm_res->sets; i++) { + irq_res.desc[i].start = rm_res->desc[i].start; + irq_res.desc[i].num = rm_res->desc[i].num; + irq_res.desc[i].start_sec = rm_res->desc[i].start_sec; + irq_res.desc[i].num_sec = rm_res->desc[i].num_sec; + } } rm_res = tisci_rm->rm_ranges[RM_RANGE_RCHAN]; - for (j = 0; j < rm_res->sets; j++, i++) { - if (rm_res->desc[j].num) { - irq_res.desc[i].start = rm_res->desc[j].start + - ud->soc_data->oes.udma_rchan; - irq_res.desc[i].num = rm_res->desc[j].num; - } - if (rm_res->desc[j].num_sec) { - irq_res.desc[i].start_sec = rm_res->desc[j].start_sec + - ud->soc_data->oes.udma_rchan; - irq_res.desc[i].num_sec = rm_res->desc[j].num_sec; + if (IS_ERR(rm_res)) { + irq_res.desc[i].start = 0; + irq_res.desc[i].num = ud->rchan_cnt; + } else { + for (j = 0; j < rm_res->sets; j++, i++) { + if (rm_res->desc[j].num) { + irq_res.desc[i].start = rm_res->desc[j].start + + ud->soc_data->oes.udma_rchan; + irq_res.desc[i].num = rm_res->desc[j].num; + } + if (rm_res->desc[j].num_sec) { + irq_res.desc[i].start_sec = rm_res->desc[j].start_sec + + ud->soc_data->oes.udma_rchan; + irq_res.desc[i].num_sec = rm_res->desc[j].num_sec; + } } } ret = ti_sci_inta_msi_domain_alloc_irqs(ud->dev, &irq_res); @@ -4690,14 +4705,15 @@ static int bcdma_setup_resources(struct udma_dev *ud) rm_res = tisci_rm->rm_ranges[RM_RANGE_BCHAN]; if (IS_ERR(rm_res)) { bitmap_zero(ud->bchan_map, ud->bchan_cnt); + irq_res.sets++; } else { bitmap_fill(ud->bchan_map, ud->bchan_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->bchan_map, &rm_res->desc[i], "bchan"); + irq_res.sets += rm_res->sets; } - irq_res.sets += rm_res->sets; }
/* tchan ranges */ @@ -4705,14 +4721,15 @@ static int bcdma_setup_resources(struct udma_dev *ud) rm_res = tisci_rm->rm_ranges[RM_RANGE_TCHAN]; if (IS_ERR(rm_res)) { bitmap_zero(ud->tchan_map, ud->tchan_cnt); + irq_res.sets += 2; } else { bitmap_fill(ud->tchan_map, ud->tchan_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->tchan_map, &rm_res->desc[i], "tchan"); + irq_res.sets += rm_res->sets * 2; } - irq_res.sets += rm_res->sets * 2; }
/* rchan ranges */ @@ -4720,47 +4737,72 @@ static int bcdma_setup_resources(struct udma_dev *ud) rm_res = tisci_rm->rm_ranges[RM_RANGE_RCHAN]; if (IS_ERR(rm_res)) { bitmap_zero(ud->rchan_map, ud->rchan_cnt); + irq_res.sets += 2; } else { bitmap_fill(ud->rchan_map, ud->rchan_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->rchan_map, &rm_res->desc[i], "rchan"); + irq_res.sets += rm_res->sets * 2; } - irq_res.sets += rm_res->sets * 2; }
irq_res.desc = kcalloc(irq_res.sets, sizeof(*irq_res.desc), GFP_KERNEL); + if (!irq_res.desc) + return -ENOMEM; if (ud->bchan_cnt) { rm_res = tisci_rm->rm_ranges[RM_RANGE_BCHAN]; - for (i = 0; i < rm_res->sets; i++) { - irq_res.desc[i].start = rm_res->desc[i].start + - oes->bcdma_bchan_ring; - irq_res.desc[i].num = rm_res->desc[i].num; + if (IS_ERR(rm_res)) { + irq_res.desc[0].start = oes->bcdma_bchan_ring; + irq_res.desc[0].num = ud->bchan_cnt; + i = 1; + } else { + for (i = 0; i < rm_res->sets; i++) { + irq_res.desc[i].start = rm_res->desc[i].start + + oes->bcdma_bchan_ring; + irq_res.desc[i].num = rm_res->desc[i].num; + } } } if (ud->tchan_cnt) { rm_res = tisci_rm->rm_ranges[RM_RANGE_TCHAN]; - for (j = 0; j < rm_res->sets; j++, i += 2) { - irq_res.desc[i].start = rm_res->desc[j].start + - oes->bcdma_tchan_data; - irq_res.desc[i].num = rm_res->desc[j].num; - - irq_res.desc[i + 1].start = rm_res->desc[j].start + - oes->bcdma_tchan_ring; - irq_res.desc[i + 1].num = rm_res->desc[j].num; + if (IS_ERR(rm_res)) { + irq_res.desc[i].start = oes->bcdma_tchan_data; + irq_res.desc[i].num = ud->tchan_cnt; + irq_res.desc[i + 1].start = oes->bcdma_tchan_ring; + irq_res.desc[i + 1].num = ud->tchan_cnt; + i += 2; + } else { + for (j = 0; j < rm_res->sets; j++, i += 2) { + irq_res.desc[i].start = rm_res->desc[j].start + + oes->bcdma_tchan_data; + irq_res.desc[i].num = rm_res->desc[j].num; + + irq_res.desc[i + 1].start = rm_res->desc[j].start + + oes->bcdma_tchan_ring; + irq_res.desc[i + 1].num = rm_res->desc[j].num; + } } } if (ud->rchan_cnt) { rm_res = tisci_rm->rm_ranges[RM_RANGE_RCHAN]; - for (j = 0; j < rm_res->sets; j++, i += 2) { - irq_res.desc[i].start = rm_res->desc[j].start + - oes->bcdma_rchan_data; - irq_res.desc[i].num = rm_res->desc[j].num; - - irq_res.desc[i + 1].start = rm_res->desc[j].start + - oes->bcdma_rchan_ring; - irq_res.desc[i + 1].num = rm_res->desc[j].num; + if (IS_ERR(rm_res)) { + irq_res.desc[i].start = oes->bcdma_rchan_data; + irq_res.desc[i].num = ud->rchan_cnt; + irq_res.desc[i + 1].start = oes->bcdma_rchan_ring; + irq_res.desc[i + 1].num = ud->rchan_cnt; + i += 2; + } else { + for (j = 0; j < rm_res->sets; j++, i += 2) { + irq_res.desc[i].start = rm_res->desc[j].start + + oes->bcdma_rchan_data; + irq_res.desc[i].num = rm_res->desc[j].num; + + irq_res.desc[i + 1].start = rm_res->desc[j].start + + oes->bcdma_rchan_ring; + irq_res.desc[i + 1].num = rm_res->desc[j].num; + } } }
@@ -4858,39 +4900,54 @@ static int pktdma_setup_resources(struct udma_dev *ud) if (IS_ERR(rm_res)) { /* all rflows are assigned exclusively to Linux */ bitmap_zero(ud->rflow_in_use, ud->rflow_cnt); + irq_res.sets = 1; } else { bitmap_fill(ud->rflow_in_use, ud->rflow_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->rflow_in_use, &rm_res->desc[i], "rflow"); + irq_res.sets = rm_res->sets; } - irq_res.sets = rm_res->sets;
/* tflow ranges */ rm_res = tisci_rm->rm_ranges[RM_RANGE_TFLOW]; if (IS_ERR(rm_res)) { /* all tflows are assigned exclusively to Linux */ bitmap_zero(ud->tflow_map, ud->tflow_cnt); + irq_res.sets++; } else { bitmap_fill(ud->tflow_map, ud->tflow_cnt); for (i = 0; i < rm_res->sets; i++) udma_mark_resource_ranges(ud, ud->tflow_map, &rm_res->desc[i], "tflow"); + irq_res.sets += rm_res->sets; } - irq_res.sets += rm_res->sets;
irq_res.desc = kcalloc(irq_res.sets, sizeof(*irq_res.desc), GFP_KERNEL); + if (!irq_res.desc) + return -ENOMEM; rm_res = tisci_rm->rm_ranges[RM_RANGE_TFLOW]; - for (i = 0; i < rm_res->sets; i++) { - irq_res.desc[i].start = rm_res->desc[i].start + - oes->pktdma_tchan_flow; - irq_res.desc[i].num = rm_res->desc[i].num; + if (IS_ERR(rm_res)) { + irq_res.desc[0].start = oes->pktdma_tchan_flow; + irq_res.desc[0].num = ud->tflow_cnt; + i = 1; + } else { + for (i = 0; i < rm_res->sets; i++) { + irq_res.desc[i].start = rm_res->desc[i].start + + oes->pktdma_tchan_flow; + irq_res.desc[i].num = rm_res->desc[i].num; + } } rm_res = tisci_rm->rm_ranges[RM_RANGE_RFLOW]; - for (j = 0; j < rm_res->sets; j++, i++) { - irq_res.desc[i].start = rm_res->desc[j].start + - oes->pktdma_rchan_flow; - irq_res.desc[i].num = rm_res->desc[j].num; + if (IS_ERR(rm_res)) { + irq_res.desc[i].start = oes->pktdma_rchan_flow; + irq_res.desc[i].num = ud->rflow_cnt; + } else { + for (j = 0; j < rm_res->sets; j++, i++) { + irq_res.desc[i].start = rm_res->desc[j].start + + oes->pktdma_rchan_flow; + irq_res.desc[i].num = rm_res->desc[j].num; + } } ret = ti_sci_inta_msi_domain_alloc_irqs(ud->dev, &irq_res); kfree(irq_res.desc);
From: Miaoqian Lin linmq006@gmail.com
[ Upstream commit ab8eb798ddabddb2944401bf31ead9671cb97d95 ]
The phy_attach() function does not return NULL. It returns error pointers.
Signed-off-by: Miaoqian Lin linmq006@gmail.com Acked-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/broadcom/genet/bcmmii.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c index 89d16c587bb7d..50ea9401f123d 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmmii.c +++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c @@ -557,9 +557,9 @@ static int bcmgenet_mii_pd_init(struct bcmgenet_priv *priv) * Internal or external PHY with MDIO access */ phydev = phy_attach(priv->dev, phy_name, pd->phy_interface); - if (!phydev) { + if (IS_ERR(phydev)) { dev_err(kdev, "failed to register PHY device\n"); - return -ENODEV; + return PTR_ERR(phydev); } } else { /*
From: Wang Qing wangqing@vivo.com
[ Upstream commit be565ec71d1d59438bed0c7ed0a252a327e0b0ef ]
Fix following coccicheck warning: WARNING: Function "for_each_child_of_node" should have of_node_put() before return.
Early exits from for_each_child_of_node should decrement the node reference counter.
Signed-off-by: Wang Qing wangqing@vivo.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/ti/am65-cpsw-nuss.c | 29 ++++++++++++++++-------- 1 file changed, 20 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/ti/am65-cpsw-nuss.c b/drivers/net/ethernet/ti/am65-cpsw-nuss.c index 130346f74ee8a..8829926e2c676 100644 --- a/drivers/net/ethernet/ti/am65-cpsw-nuss.c +++ b/drivers/net/ethernet/ti/am65-cpsw-nuss.c @@ -1844,13 +1844,14 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) if (ret < 0) { dev_err(dev, "%pOF error reading port_id %d\n", port_np, ret); - return ret; + goto of_node_put; }
if (!port_id || port_id > common->port_num) { dev_err(dev, "%pOF has invalid port_id %u %s\n", port_np, port_id, port_np->name); - return -EINVAL; + ret = -EINVAL; + goto of_node_put; }
port = am65_common_get_port(common, port_id); @@ -1866,8 +1867,10 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) (AM65_CPSW_NU_FRAM_PORT_OFFSET * (port_id - 1));
port->slave.mac_sl = cpsw_sl_get("am65", dev, port->port_base); - if (IS_ERR(port->slave.mac_sl)) - return PTR_ERR(port->slave.mac_sl); + if (IS_ERR(port->slave.mac_sl)) { + ret = PTR_ERR(port->slave.mac_sl); + goto of_node_put; + }
port->disabled = !of_device_is_available(port_np); if (port->disabled) { @@ -1880,7 +1883,7 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) ret = PTR_ERR(port->slave.ifphy); dev_err(dev, "%pOF error retrieving port phy: %d\n", port_np, ret); - return ret; + goto of_node_put; }
port->slave.mac_only = @@ -1889,10 +1892,12 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) /* get phy/link info */ if (of_phy_is_fixed_link(port_np)) { ret = of_phy_register_fixed_link(port_np); - if (ret) - return dev_err_probe(dev, ret, + if (ret) { + ret = dev_err_probe(dev, ret, "failed to register fixed-link phy %pOF\n", port_np); + goto of_node_put; + } port->slave.phy_node = of_node_get(port_np); } else { port->slave.phy_node = @@ -1902,14 +1907,15 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) if (!port->slave.phy_node) { dev_err(dev, "slave[%d] no phy found\n", port_id); - return -ENODEV; + ret = -ENODEV; + goto of_node_put; }
ret = of_get_phy_mode(port_np, &port->slave.phy_if); if (ret) { dev_err(dev, "%pOF read phy-mode err %d\n", port_np, ret); - return ret; + goto of_node_put; }
ret = of_get_mac_address(port_np, port->slave.mac_addr); @@ -1932,6 +1938,11 @@ static int am65_cpsw_nuss_init_slave_ports(struct am65_cpsw_common *common) }
return 0; + +of_node_put: + of_node_put(port_np); + of_node_put(node); + return ret; }
static void am65_cpsw_pcpu_stats_free(void *data)
From: John Garry john.garry@huawei.com
[ Upstream commit 2fe24343922e0428fb68674a4fae099171141bc7 ]
The driver supports a "direct" mode of operation, where the SMP req frame is directly copied into the command payload (and vice-versa for the SMP resp).
To get at the SMP req frame data in the scatterlist the driver uses phys_to_virt() on the DMA mapped memory dma_addr_t . This is broken, and subsequently crashes as follows when an IOMMU is enabled:
Unable to handle kernel paging request at virtual address ffff0000fcebfb00 ... pc : pm80xx_chip_smp_req+0x2d0/0x3d0 lr : pm80xx_chip_smp_req+0xac/0x3d0 pm80xx_chip_smp_req+0x2d0/0x3d0 pm8001_task_exec.constprop.0+0x368/0x520 pm8001_queue_command+0x1c/0x30 smp_execute_task_sg+0xdc/0x204 sas_discover_expander.part.0+0xac/0x6cc sas_discover_root_expander+0x8c/0x150 sas_discover_domain+0x3ac/0x6a0 process_one_work+0x1d0/0x354 worker_thread+0x13c/0x470 kthread+0x17c/0x190 ret_from_fork+0x10/0x20 Code: 371806e1 910006d6 6b16033f 54000249 (38766b05) ---[ end trace b91d59aaee98ea2d ]--- note: kworker/u192:0[7] exited with preempt_count 1
Instead use kmap_atomic().
-- Difference to v1: - use kmap_atomic() in both locations Difference to v2: - add whitespace around arithmetic (Damien)
Link: https://lore.kernel.org/r/1639390248-213603-1-git-send-email-john.garry@huaw... Reviewed-by: Damien Le Moal damien.lemoal@opensource.wdc.com Signed-off-by: John Garry john.garry@huawei.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/pm8001/pm80xx_hwi.c | 38 ++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 17 deletions(-)
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c index ed02e1aaf868c..3c74aea53c18b 100644 --- a/drivers/scsi/pm8001/pm80xx_hwi.c +++ b/drivers/scsi/pm8001/pm80xx_hwi.c @@ -3053,7 +3053,6 @@ mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) struct smp_completion_resp *psmpPayload; struct task_status_struct *ts; struct pm8001_device *pm8001_dev; - char *pdma_respaddr = NULL;
psmpPayload = (struct smp_completion_resp *)(piomb + 4); status = le32_to_cpu(psmpPayload->status); @@ -3080,19 +3079,23 @@ mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) if (pm8001_dev) atomic_dec(&pm8001_dev->running_req); if (pm8001_ha->smp_exp_mode == SMP_DIRECT) { + struct scatterlist *sg_resp = &t->smp_task.smp_resp; + u8 *payload; + void *to; + pm8001_dbg(pm8001_ha, IO, "DIRECT RESPONSE Length:%d\n", param); - pdma_respaddr = (char *)(phys_to_virt(cpu_to_le64 - ((u64)sg_dma_address - (&t->smp_task.smp_resp)))); + to = kmap_atomic(sg_page(sg_resp)); + payload = to + sg_resp->offset; for (i = 0; i < param; i++) { - *(pdma_respaddr+i) = psmpPayload->_r_a[i]; + *(payload + i) = psmpPayload->_r_a[i]; pm8001_dbg(pm8001_ha, IO, "SMP Byte%d DMA data 0x%x psmp 0x%x\n", - i, *(pdma_respaddr + i), + i, *(payload + i), psmpPayload->_r_a[i]); } + kunmap_atomic(to); } break; case IO_ABORTED: @@ -4232,14 +4235,14 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, struct sas_task *task = ccb->task; struct domain_device *dev = task->dev; struct pm8001_device *pm8001_dev = dev->lldd_dev; - struct scatterlist *sg_req, *sg_resp; + struct scatterlist *sg_req, *sg_resp, *smp_req; u32 req_len, resp_len; struct smp_req smp_cmd; u32 opc; struct inbound_queue_table *circularQ; - char *preq_dma_addr = NULL; - __le64 tmp_addr; u32 i, length; + u8 *payload; + u8 *to;
memset(&smp_cmd, 0, sizeof(smp_cmd)); /* @@ -4276,8 +4279,9 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, pm8001_ha->smp_exp_mode = SMP_INDIRECT;
- tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req)); - preq_dma_addr = (char *)phys_to_virt(tmp_addr); + smp_req = &task->smp_task.smp_req; + to = kmap_atomic(sg_page(smp_req)); + payload = to + smp_req->offset;
/* INDIRECT MODE command settings. Use DMA */ if (pm8001_ha->smp_exp_mode == SMP_INDIRECT) { @@ -4285,7 +4289,7 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, /* for SPCv indirect mode. Place the top 4 bytes of * SMP Request header here. */ for (i = 0; i < 4; i++) - smp_cmd.smp_req16[i] = *(preq_dma_addr + i); + smp_cmd.smp_req16[i] = *(payload + i); /* exclude top 4 bytes for SMP req header */ smp_cmd.long_smp_req.long_req_addr = cpu_to_le64((u64)sg_dma_address @@ -4316,20 +4320,20 @@ static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha, pm8001_dbg(pm8001_ha, IO, "SMP REQUEST DIRECT MODE\n"); for (i = 0; i < length; i++) if (i < 16) { - smp_cmd.smp_req16[i] = *(preq_dma_addr+i); + smp_cmd.smp_req16[i] = *(payload + i); pm8001_dbg(pm8001_ha, IO, "Byte[%d]:%x (DMA data:%x)\n", i, smp_cmd.smp_req16[i], - *(preq_dma_addr)); + *(payload)); } else { - smp_cmd.smp_req[i] = *(preq_dma_addr+i); + smp_cmd.smp_req[i] = *(payload + i); pm8001_dbg(pm8001_ha, IO, "Byte[%d]:%x (DMA data:%x)\n", i, smp_cmd.smp_req[i], - *(preq_dma_addr)); + *(payload)); } } - + kunmap_atomic(to); build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag, &smp_cmd, pm8001_ha->smp_exp_mode, length); rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &smp_cmd,
From: Ilan Peer ilan.peer@intel.com
[ Upstream commit f22d981386d12d1513bd2720fb4387b469124d4b ]
Instead of using the hard-coded value of '100' use the correct scan IEs length as calculated during HW registration to mac80211.
Signed-off-by: Ilan Peer ilan.peer@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.0a82d6891719.I8ded1f2e0bccb... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/util.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/net/mac80211/util.c b/net/mac80211/util.c index 03ea4f929b997..39961a4f55d12 100644 --- a/net/mac80211/util.c +++ b/net/mac80211/util.c @@ -2061,7 +2061,7 @@ struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata, chandef.chan = chan;
skb = ieee80211_probereq_get(&local->hw, src, ssid, ssid_len, - 100 + ie_len); + local->scan_ies_len + ie_len); if (!skb) return NULL;
From: Mordechay Goodstein mordechay.goodstein@intel.com
[ Upstream commit 4dde3c3627b52ca515a34f6f4de3898224aa1dd3 ]
Currently channel context is updated only after station got an update about new assoc state, this results in station using the old channel context.
Fix this by moving the update channel context before updating station, enabling the driver to immediately use the updated channel context in the new assoc state.
Signed-off-by: Mordechay Goodstein mordechay.goodstein@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.1c80c17ffd8a.I94ae31378b363... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/sta_info.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/net/mac80211/sta_info.c b/net/mac80211/sta_info.c index 6eeef7a61927b..9e0bb402674c9 100644 --- a/net/mac80211/sta_info.c +++ b/net/mac80211/sta_info.c @@ -664,6 +664,15 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU)
list_add_tail_rcu(&sta->list, &local->sta_list);
+ /* update channel context before notifying the driver about state + * change, this enables driver using the updated channel context right away. + */ + if (sta->sta_state >= IEEE80211_STA_ASSOC) { + ieee80211_recalc_min_chandef(sta->sdata); + if (!sta->sta.support_p2p_ps) + ieee80211_recalc_p2p_go_ps_allowed(sta->sdata); + } + /* notify driver */ err = sta_info_insert_drv_state(local, sdata, sta); if (err) @@ -671,12 +680,6 @@ static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU)
set_sta_flag(sta, WLAN_STA_INSERTED);
- if (sta->sta_state >= IEEE80211_STA_ASSOC) { - ieee80211_recalc_min_chandef(sta->sdata); - if (!sta->sta.support_p2p_ps) - ieee80211_recalc_p2p_go_ps_allowed(sta->sdata); - } - /* accept BA sessions now */ clear_sta_flag(sta, WLAN_STA_BLOCK_BA);
From: Johannes Berg johannes.berg@intel.com
[ Upstream commit 13dee10b30c058ee2c58c5da00339cc0d4201aa6 ]
When we reconfigure, the driver might do some things to complete the reconfiguration. It's strange and could be broken in some cases because we restart other works (e.g. remain-on-channel and TX) before this happens, yet only start queues later.
Change this to do the reconfig complete when reconfiguration is actually complete, not when we've already started doing other things again.
For iwlwifi, this should fix a race where the reconfig can race with TX, for ath10k and ath11k that also use this it won't make a difference because they just start queues there, and mac80211 also stopped the queues and will restart them later as before.
Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Luca Coelho luciano.coelho@intel.com Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15f... Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/util.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/net/mac80211/util.c b/net/mac80211/util.c index 39961a4f55d12..a94223710d48d 100644 --- a/net/mac80211/util.c +++ b/net/mac80211/util.c @@ -2644,6 +2644,13 @@ int ieee80211_reconfig(struct ieee80211_local *local) mutex_unlock(&local->sta_mtx); }
+ /* + * If this is for hw restart things are still running. + * We may want to change that later, however. + */ + if (local->open_count && (!suspended || reconfig_due_to_wowlan)) + drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART); + if (local->in_reconfig) { local->in_reconfig = false; barrier(); @@ -2662,13 +2669,6 @@ int ieee80211_reconfig(struct ieee80211_local *local) IEEE80211_QUEUE_STOP_REASON_SUSPEND, false);
- /* - * If this is for hw restart things are still running. - * We may want to change that later, however. - */ - if (local->open_count && (!suspended || reconfig_due_to_wowlan)) - drv_reconfig_complete(local, IEEE80211_RECONFIG_TYPE_RESTART); - if (!suspended) return 0;
From: Nicholas Kazlauskas nicholas.kazlauskas@amd.com
[ Upstream commit 791255ca9fbe38042cfd55df5deb116dc11fef18 ]
[Why] If the firmware wasn't reset by PSP or HW and is currently running then the firmware will hang or perform underfined behavior when we modify its firmware state underneath it.
[How] Reset DMCUB before setting up cache windows and performing HW init.
Reviewed-by: Aurabindo Jayamohanan Pillai Aurabindo.Pillai@amd.com Acked-by: Pavle Kotarac Pavle.Kotarac@amd.com Tested-by: Daniel Wheeler daniel.wheeler@amd.com Signed-off-by: Nicholas Kazlauskas nicholas.kazlauskas@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c | 5 +++++ 1 file changed, 5 insertions(+)
diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c index fef13e93a99fd..bdc894bd66e31 100644 --- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c +++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c @@ -900,6 +900,11 @@ static int dm_dmub_hw_init(struct amdgpu_device *adev) return 0; }
+ /* Reset DMCUB if it was previously running - before we overwrite its memory. */ + status = dmub_srv_hw_reset(dmub_srv); + if (status != DMUB_STATUS_OK) + DRM_WARN("Error resetting DMUB HW: %d\n", status); + hdr = (const struct dmcub_firmware_header_v1_0 *)dmub_fw->data;
fw_inst_const = dmub_fw->data +
From: Evan Quan evan.quan@amd.com
[ Upstream commit 17c65d6fca844ee72a651944d8ce721e9040bf70 ]
Pair the operations did in GMC ->hw_init and ->hw_fini. That can help to maintain correct cached state for GMC and avoid unintention gate operation dropping due to wrong cached state.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: Evan Quan evan.quan@amd.com Acked-by: Guchun Chen guchun.chen@amd.com Reviewed-by: Mario Limonciello mario.limonciello@amd.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c | 8 ++++++++ drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c | 8 ++++---- drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c | 7 ++++++- 3 files changed, 18 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c b/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c index 5551359d5dfdc..398596aac8ca5 100644 --- a/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c +++ b/drivers/gpu/drm/amd/amdgpu/gmc_v9_0.c @@ -1802,6 +1802,14 @@ static int gmc_v9_0_hw_fini(void *handle) return 0; }
+ /* + * Pair the operations did in gmc_v9_0_hw_init and thus maintain + * a correct cached state for GMC. Otherwise, the "gate" again + * operation on S3 resuming will fail due to wrong cached state. + */ + if (adev->mmhub.funcs->update_power_gating) + adev->mmhub.funcs->update_power_gating(adev, false); + amdgpu_irq_put(adev, &adev->gmc.ecc_irq, 0); amdgpu_irq_put(adev, &adev->gmc.vm_fault, 0);
diff --git a/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c b/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c index a99953833820e..3ef5e368d125d 100644 --- a/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c +++ b/drivers/gpu/drm/amd/amdgpu/mmhub_v1_0.c @@ -302,10 +302,10 @@ static void mmhub_v1_0_update_power_gating(struct amdgpu_device *adev, if (amdgpu_sriov_vf(adev)) return;
- if (enable && adev->pg_flags & AMD_PG_SUPPORT_MMHUB) { - amdgpu_dpm_set_powergating_by_smu(adev, AMD_IP_BLOCK_TYPE_GMC, true); - - } + if (adev->pg_flags & AMD_PG_SUPPORT_MMHUB) + amdgpu_dpm_set_powergating_by_smu(adev, + AMD_IP_BLOCK_TYPE_GMC, + enable); }
static int mmhub_v1_0_gart_enable(struct amdgpu_device *adev) diff --git a/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c b/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c index 321215003643b..69f67206b5b5a 100644 --- a/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c +++ b/drivers/gpu/drm/amd/pm/powerplay/amd_powerplay.c @@ -1332,7 +1332,12 @@ static int pp_set_powergating_by_smu(void *handle, pp_dpm_powergate_vce(handle, gate); break; case AMD_IP_BLOCK_TYPE_GMC: - pp_dpm_powergate_mmhub(handle); + /* + * For now, this is only used on PICASSO. + * And only "gate" operation is supported. + */ + if (gate) + pp_dpm_powergate_mmhub(handle); break; case AMD_IP_BLOCK_TYPE_GFX: ret = pp_dpm_powergate_gfx(handle, gate);
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index c2d912d0c976c..a728434fcff87 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,6 +1625,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) { + if (!delay) + return queue_work_on(cpu, kblockd_workqueue, &dwork->work); return mod_delayed_work_on(cpu, kblockd_workqueue, dwork, delay); } EXPORT_SYMBOL(kblockd_mod_delayed_work_on);
From: Sasha Levin sashal@kernel.org Sent: Monday, December 20, 2021 5:58 PM
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org
block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index c2d912d0c976c..a728434fcff87 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,6 +1625,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) {
- if (!delay)
return queue_work_on(cpu, kblockd_workqueue, &dwork->work);} EXPORT_SYMBOL(kblockd_mod_delayed_work_on); -- 2.34.1
Sasha -- there are reports of this patch causing performance problems. See https://lore.kernel.org/lkml/1639853092.524jxfaem2.none@localhost/. I would suggest *not* backporting it to any of the stable branches until the issues are fully sorted out.
Michael
On 12/21/21 8:35 AM, Michael Kelley (LINUX) wrote:
From: Sasha Levin sashal@kernel.org Sent: Monday, December 20, 2021 5:58 PM
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org
block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index c2d912d0c976c..a728434fcff87 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,6 +1625,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) {
- if (!delay)
return queue_work_on(cpu, kblockd_workqueue, &dwork->work);} EXPORT_SYMBOL(kblockd_mod_delayed_work_on); -- 2.34.1
Sasha -- there are reports of this patch causing performance problems. See https://lore.kernel.org/lkml/1639853092.524jxfaem2.none@localhost/. I would suggest *not* backporting it to any of the stable branches until the issues are fully sorted out.
Both this and the revert were backported. Which arguably doesn't make a lot of sense, but at least it's consistent and won't cause any issues...
On Tue, Dec 21, 2021 at 08:36:33AM -0700, Jens Axboe wrote:
On 12/21/21 8:35 AM, Michael Kelley (LINUX) wrote:
From: Sasha Levin sashal@kernel.org Sent: Monday, December 20, 2021 5:58 PM
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org
block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index c2d912d0c976c..a728434fcff87 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,6 +1625,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) {
- if (!delay)
return queue_work_on(cpu, kblockd_workqueue, &dwork->work);} EXPORT_SYMBOL(kblockd_mod_delayed_work_on); -- 2.34.1
Sasha -- there are reports of this patch causing performance problems. See https://lore.kernel.org/lkml/1639853092.524jxfaem2.none@localhost/. I would suggest *not* backporting it to any of the stable branches until the issues are fully sorted out.
Both this and the revert were backported. Which arguably doesn't make a lot of sense, but at least it's consistent and won't cause any issues...
The logic behind it is that it makes it easy for both us as well as everyone else to annotate why a certain patch might be "missing" from the trees - in this case because it was reverted.
It looks dumb now, but it saves a lot of time as well as mitigates the risk of it being picked up again at some point in the future.
On 12/21/21 10:58 AM, Sasha Levin wrote:
On Tue, Dec 21, 2021 at 08:36:33AM -0700, Jens Axboe wrote:
On 12/21/21 8:35 AM, Michael Kelley (LINUX) wrote:
From: Sasha Levin sashal@kernel.org Sent: Monday, December 20, 2021 5:58 PM
From: Jens Axboe axboe@kernel.dk
[ Upstream commit cb2ac2912a9ca7d3d26291c511939a41361d2d83 ]
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately.
Avoid hammering on the timer and just use queue_work_on() if no delay has been specified.
Reported-and-tested-by: Dexuan Cui decui@microsoft.com Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@B... Reviewed-by: Ming Lei ming.lei@redhat.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org
block/blk-core.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/block/blk-core.c b/block/blk-core.c index c2d912d0c976c..a728434fcff87 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,6 +1625,8 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) {
- if (!delay)
return queue_work_on(cpu, kblockd_workqueue, &dwork->work);} EXPORT_SYMBOL(kblockd_mod_delayed_work_on); -- 2.34.1
Sasha -- there are reports of this patch causing performance problems. See https://lore.kernel.org/lkml/1639853092.524jxfaem2.none@localhost/. I would suggest *not* backporting it to any of the stable branches until the issues are fully sorted out.
Both this and the revert were backported. Which arguably doesn't make a lot of sense, but at least it's consistent and won't cause any issues...
The logic behind it is that it makes it easy for both us as well as everyone else to annotate why a certain patch might be "missing" from the trees - in this case because it was reverted.
It looks dumb now, but it saves a lot of time as well as mitigates the risk of it being picked up again at some point in the future.
It's fine with me, when I saw the first patch yesterday I did get worried, but then I saw the revert was picked too. As I said, as long as the end result is sane, then there's no harm in doing it this way.
From: Greg Jesionowski jesionowskigreg@gmail.com
[ Upstream commit ef8a0f6eab1ca5d1a75c242c5c7b9d386735fa0a ]
This adds the vendor and product IDs for the AT29M2-AF which is a lan7801-based device.
Signed-off-by: Greg Jesionowski jesionowskigreg@gmail.com Link: https://lore.kernel.org/r/20211214221027.305784-1-jesionowskigreg@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/lan78xx.c | 6 ++++++ 1 file changed, 6 insertions(+)
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c index a0401a9dade5b..3e1a83a22fdd6 100644 --- a/drivers/net/usb/lan78xx.c +++ b/drivers/net/usb/lan78xx.c @@ -76,6 +76,8 @@ #define LAN7801_USB_PRODUCT_ID (0x7801) #define LAN78XX_EEPROM_MAGIC (0x78A5) #define LAN78XX_OTP_MAGIC (0x78F3) +#define AT29M2AF_USB_VENDOR_ID (0x07C9) +#define AT29M2AF_USB_PRODUCT_ID (0x0012)
#define MII_READ 1 #define MII_WRITE 0 @@ -4734,6 +4736,10 @@ static const struct usb_device_id products[] = { /* LAN7801 USB Gigabit Ethernet Device */ USB_DEVICE(LAN78XX_USB_VENDOR_ID, LAN7801_USB_PRODUCT_ID), }, + { + /* ATM2-AF USB Gigabit Ethernet Device */ + USB_DEVICE(AT29M2AF_USB_VENDOR_ID, AT29M2AF_USB_PRODUCT_ID), + }, {}, }; MODULE_DEVICE_TABLE(usb, products);
From: Wenliang Wang wangwenliang.1995@bytedance.com
[ Upstream commit 053c9e18c6f9cf82242ef35ac21cae1842725714 ]
We found the stat of rx drops for small pkts does not increment when build_skb fail, it's not coherent with other mode's rx drops stat.
Signed-off-by: Wenliang Wang wangwenliang.1995@bytedance.com Acked-by: Jason Wang jasowang@redhat.com Acked-by: Michael S. Tsirkin mst@redhat.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/virtio_net.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index 4ad25a8b0870c..1231b48f7183e 100644 --- a/drivers/net/virtio_net.c +++ b/drivers/net/virtio_net.c @@ -730,7 +730,7 @@ static struct sk_buff *receive_small(struct net_device *dev, pr_debug("%s: rx error: len %u exceeds max size %d\n", dev->name, len, GOOD_PACKET_LEN); dev->stats.rx_length_errors++; - goto err_len; + goto err; } rcu_read_lock(); xdp_prog = rcu_dereference(rq->xdp_prog); @@ -815,10 +815,8 @@ static struct sk_buff *receive_small(struct net_device *dev, rcu_read_unlock();
skb = build_skb(buf, buflen); - if (!skb) { - put_page(page); + if (!skb) goto err; - } skb_reserve(skb, headroom - delta); skb_put(skb, len); if (!xdp_prog) { @@ -829,13 +827,12 @@ static struct sk_buff *receive_small(struct net_device *dev, if (metasize) skb_metadata_set(skb, metasize);
-err: return skb;
err_xdp: rcu_read_unlock(); stats->xdp_drops++; -err_len: +err: stats->drops++; put_page(page); xdp_xmit:
From: Daniel Borkmann daniel@iogearbox.net
[ Upstream commit e572ff80f05c33cd0cb4860f864f5c9c044280b6 ]
Make the bounds propagation in __reg_assign_32_into_64() slightly more robust and readable by aligning it similarly as we did back in the __reg_combine_64_into_32() counterpart. Meaning, only propagate or pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann daniel@iogearbox.net Reviewed-by: John Fastabend john.fastabend@gmail.com Acked-by: Alexei Starovoitov ast@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/bpf/verifier.c | 24 +++++++++++++++--------- 1 file changed, 15 insertions(+), 9 deletions(-)
diff --git a/kernel/bpf/verifier.c b/kernel/bpf/verifier.c index 8a0b4879790e5..03f627e7e233b 100644 --- a/kernel/bpf/verifier.c +++ b/kernel/bpf/verifier.c @@ -1358,22 +1358,28 @@ static void __reg_bound_offset(struct bpf_reg_state *reg) reg->var_off = tnum_or(tnum_clear_subreg(var64_off), var32_off); }
+static bool __reg32_bound_s64(s32 a) +{ + return a >= 0 && a <= S32_MAX; +} + static void __reg_assign_32_into_64(struct bpf_reg_state *reg) { reg->umin_value = reg->u32_min_value; reg->umax_value = reg->u32_max_value; - /* Attempt to pull 32-bit signed bounds into 64-bit bounds - * but must be positive otherwise set to worse case bounds - * and refine later from tnum. + + /* Attempt to pull 32-bit signed bounds into 64-bit bounds but must + * be positive otherwise set to worse case bounds and refine later + * from tnum. */ - if (reg->s32_min_value >= 0 && reg->s32_max_value >= 0) - reg->smax_value = reg->s32_max_value; - else - reg->smax_value = U32_MAX; - if (reg->s32_min_value >= 0) + if (__reg32_bound_s64(reg->s32_min_value) && + __reg32_bound_s64(reg->s32_max_value)) { reg->smin_value = reg->s32_min_value; - else + reg->smax_value = reg->s32_max_value; + } else { reg->smin_value = 0; + reg->smax_value = U32_MAX; + } }
static void __reg_combine_32_into_64(struct bpf_reg_state *reg)
From: Vincent Pelletier plr.vincent@gmail.com
[ Upstream commit ea81b91e4e256b0bb75d47ad3a5c230b2171a005 ]
Follow the pin descriptions given in the version 3 of the board schematics.
Signed-off-by: Vincent Pelletier plr.vincent@gmail.com Signed-off-by: Palmer Dabbelt palmer@rivosinc.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts | 4 ++++ 1 file changed, 4 insertions(+)
diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index 2e4ea84f27e77..a788b99638af8 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -250,4 +250,8 @@ &pwm1 {
&gpio { status = "okay"; + gpio-line-names = "J29.1", "PMICNTB", "PMICSHDN", "J8.1", "J8.3", + "PCIe_PWREN", "THERM", "UBRDG_RSTN", "PCIe_PERSTN", + "ULPI_RSTN", "J8.2", "UHUB_RSTN", "GEMGXL_RST", "J8.4", + "EN_VDD_SD", "SD_CD"; };
From: Vincent Pelletier plr.vincent@gmail.com
[ Upstream commit 8120393b74b31bbaf293f59896de6b0d50febc48 ]
Mark it as read-only as it is factory-programmed with identifying information, and no executable nor configuration: - eth MAC address - board model (PCB version, BoM version) - board serial number Accidental modification would cause misidentification which could brick the board, so marking read-only seem like both a safe and non-constraining choice.
Signed-off-by: Vincent Pelletier plr.vincent@gmail.com Signed-off-by: Palmer Dabbelt palmer@rivosinc.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index a788b99638af8..7ea1c8da5fb2e 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -63,6 +63,16 @@ temperature-sensor@4c { interrupts = <6 IRQ_TYPE_LEVEL_LOW>; };
+ eeprom@54 { + compatible = "microchip,24c02", "atmel,24c02"; + reg = <0x54>; + vcc-supply = <&vdd_bpro>; + label = "board-id"; + pagesize = <16>; + read-only; + size = <256>; + }; + pmic@58 { compatible = "dlg,da9063"; reg = <0x58>;
From: Vincent Pelletier plr.vincent@gmail.com
[ Upstream commit cd29cc8ad2540a4f9a0a3e174394d39e648ef941 ]
These sub-functions are available in the chip revision on this board, so expose them.
Signed-off-by: Vincent Pelletier plr.vincent@gmail.com Signed-off-by: Palmer Dabbelt palmer@rivosinc.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+)
diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index 7ea1c8da5fb2e..dd110ba00e871 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -80,6 +80,18 @@ pmic@58 { interrupts = <1 IRQ_TYPE_LEVEL_LOW>; interrupt-controller;
+ onkey { + compatible = "dlg,da9063-onkey"; + }; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + regulators { vdd_bcore1: bcore1 { regulator-min-microvolt = <900000>;
From: Vincent Pelletier plr.vincent@gmail.com
[ Upstream commit ad931d9b3b2e21586de8e6b34346d0a30c13721d ]
The existing values are rejected by the da9063 regulator driver, as they are unachievable with the declared chip setup (non-merged vcore and bmem are unable to provide the declared curent).
Fix voltages to match rev3 schematics, which also matches their boot-up configuration within the chip's available precision. Declare bcore1/bcore2 and bmem/bio as merged. Set ldo09 and ldo10 as always-on as their consumers are not declared but exist. Drop ldo current limits as there is no current limit feature for these regulators in the DA9063. Fixes warnings like: DA9063_LDO3: Operation of current configuration missing
Signed-off-by: Vincent Pelletier plr.vincent@gmail.com Signed-off-by: Palmer Dabbelt palmer@rivosinc.com Signed-off-by: Sasha Levin sashal@kernel.org --- .../boot/dts/sifive/hifive-unmatched-a00.dts | 84 ++++++------------- 1 file changed, 24 insertions(+), 60 deletions(-)
diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index dd110ba00e871..09d9342282339 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -93,47 +93,31 @@ wdt { };
regulators { - vdd_bcore1: bcore1 { - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - regulator-min-microamp = <5000000>; - regulator-max-microamp = <5000000>; - regulator-always-on; - }; - - vdd_bcore2: bcore2 { - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - regulator-min-microamp = <5000000>; - regulator-max-microamp = <5000000>; + vdd_bcore: bcores-merged { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-min-microamp = <4800000>; + regulator-max-microamp = <4800000>; regulator-always-on; };
vdd_bpro: bpro { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <2500000>; - regulator-max-microamp = <2500000>; + regulator-min-microamp = <2400000>; + regulator-max-microamp = <2400000>; regulator-always-on; };
vdd_bperi: bperi { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; + regulator-min-microvolt = <1060000>; + regulator-max-microvolt = <1060000>; regulator-min-microamp = <1500000>; regulator-max-microamp = <1500000>; regulator-always-on; };
- vdd_bmem: bmem { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-min-microamp = <3000000>; - regulator-max-microamp = <3000000>; - regulator-always-on; - }; - - vdd_bio: bio { + vdd_bmem_bio: bmem-bio-merged { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-min-microamp = <3000000>; @@ -144,86 +128,66 @@ vdd_bio: bio { vdd_ldo1: ldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <100000>; - regulator-max-microamp = <100000>; regulator-always-on; };
vdd_ldo2: ldo2 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; regulator-always-on; };
vdd_ldo3: ldo3 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; };
vdd_ldo4: ldo4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; regulator-always-on; };
vdd_ldo5: ldo5 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <100000>; - regulator-max-microamp = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; };
vdd_ldo6: ldo6 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-always-on; };
vdd_ldo7: ldo7 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; };
vdd_ldo8: ldo8 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; };
vdd_ld09: ldo9 { regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-always-on; };
vdd_ldo10: ldo10 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; - regulator-min-microamp = <300000>; - regulator-max-microamp = <300000>; + regulator-always-on; };
vdd_ldo11: ldo11 { regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; - regulator-min-microamp = <300000>; - regulator-max-microamp = <300000>; regulator-always-on; }; };
From: Vincent Pelletier plr.vincent@gmail.com
[ Upstream commit f6f7fbb89bf8dc9132fde55cfe67483138eea880 ]
Fixes the following probe warning: lm90 0-004c: Looking up vcc-supply from device tree lm90 0-004c: Looking up vcc-supply property in node /soc/i2c@10030000/temperature-sensor@4c failed lm90 0-004c: supply vcc not found, using dummy regulator
Signed-off-by: Vincent Pelletier plr.vincent@gmail.com Signed-off-by: Palmer Dabbelt palmer@rivosinc.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts | 1 + 1 file changed, 1 insertion(+)
diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index 09d9342282339..0c4a508869059 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -59,6 +59,7 @@ &i2c0 { temperature-sensor@4c { compatible = "ti,tmp451"; reg = <0x4c>; + vcc-supply = <&vdd_bpro>; interrupt-parent = <&gpio>; interrupts = <6 IRQ_TYPE_LEVEL_LOW>; };
From: Jens Axboe axboe@kernel.dk
[ Upstream commit 87959fa16cfbcf76245c11559db1940069621274 ]
This reverts commit cb2ac2912a9ca7d3d26291c511939a41361d2d83.
Alex and the kernel test robot report that this causes a significant performance regression with BFQ. I can reproduce that result, so let's revert this one as we're close to -rc6 and we there's no point in trying to rush a fix.
Link: https://lore.kernel.org/linux-block/1639853092.524jxfaem2.none@localhost/ Link: https://lore.kernel.org/lkml/20211219141852.GH14057@xsang-OptiPlex-9020/ Reported-by: Alex Xu (Hello71) alex_y_xu@yahoo.ca Reported-by: kernel test robot oliver.sang@intel.com Signed-off-by: Jens Axboe axboe@kernel.dk Signed-off-by: Sasha Levin sashal@kernel.org --- block/blk-core.c | 2 -- 1 file changed, 2 deletions(-)
diff --git a/block/blk-core.c b/block/blk-core.c index a728434fcff87..c2d912d0c976c 100644 --- a/block/blk-core.c +++ b/block/blk-core.c @@ -1625,8 +1625,6 @@ EXPORT_SYMBOL(kblockd_schedule_work); int kblockd_mod_delayed_work_on(int cpu, struct delayed_work *dwork, unsigned long delay) { - if (!delay) - return queue_work_on(cpu, kblockd_workqueue, &dwork->work); return mod_delayed_work_on(cpu, kblockd_workqueue, dwork, delay); } EXPORT_SYMBOL(kblockd_mod_delayed_work_on);
linux-stable-mirror@lists.linaro.org
-
Jens Axboe -
Michael Kelley (LINUX) -
Sasha Levin -
Sedat Dilek