From: Axel Lin axel.lin@ingics.com
[ Upstream commit 6549c46af8551b346bcc0b9043f93848319acd5c ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f. If value is from 20 to 31, the voltage will all be fixed to 3V. And LDO also, just vout range is different from 1.2v to 3v, step is the same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin axel.lin@ingics.com Reviewed-by: ChiYuan Huang cy_huang@richtek.com Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- include/linux/mfd/rt5033-private.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/include/linux/mfd/rt5033-private.h b/include/linux/mfd/rt5033-private.h index f812105c538c..f2271bfb3273 100644 --- a/include/linux/mfd/rt5033-private.h +++ b/include/linux/mfd/rt5033-private.h @@ -200,13 +200,13 @@ enum rt5033_reg { #define RT5033_REGULATOR_BUCK_VOLTAGE_MIN 1000000U #define RT5033_REGULATOR_BUCK_VOLTAGE_MAX 3000000U #define RT5033_REGULATOR_BUCK_VOLTAGE_STEP 100000U -#define RT5033_REGULATOR_BUCK_VOLTAGE_STEP_NUM 32 +#define RT5033_REGULATOR_BUCK_VOLTAGE_STEP_NUM 21
/* RT5033 regulator LDO output voltage uV */ #define RT5033_REGULATOR_LDO_VOLTAGE_MIN 1200000U #define RT5033_REGULATOR_LDO_VOLTAGE_MAX 3000000U #define RT5033_REGULATOR_LDO_VOLTAGE_STEP 100000U -#define RT5033_REGULATOR_LDO_VOLTAGE_STEP_NUM 32 +#define RT5033_REGULATOR_LDO_VOLTAGE_STEP_NUM 19
/* RT5033 regulator SAFE LDO output voltage uV */ #define RT5033_REGULATOR_SAFE_LDO_VOLTAGE 4900000U
From: Alain Volmat alain.volmat@foss.st.com
[ Upstream commit e4a5c19888a5f8a9390860ca493e643be58c8791 ]
In case of Full-Duplex mode, DXP flag is set when RXP and TXP flags are set. But to avoid 2 different handlings, just add TXP and RXP flag in the mask instead of DXP, and then keep the initial handling of TXP and RXP events. Also rephrase comment about EOTIE which is one of the interrupt enable bits. It is not triggered by any event.
Signed-off-by: Amelie Delaunay amelie.delaunay@foss.st.com Signed-off-by: Alain Volmat alain.volmat@foss.st.com Reviewed-by: Amelie Delaunay amelie.delaunay@foss.st.com Link: https://lore.kernel.org/r/1625042723-661-3-git-send-email-alain.volmat@foss.... Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/spi/spi-stm32.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c index 3af6a5a3a4b2..92bf667951b0 100644 --- a/drivers/spi/spi-stm32.c +++ b/drivers/spi/spi-stm32.c @@ -913,15 +913,18 @@ static irqreturn_t stm32h7_spi_irq_thread(int irq, void *dev_id) ier = readl_relaxed(spi->base + STM32H7_SPI_IER);
mask = ier; - /* EOTIE is triggered on EOT, SUSP and TXC events. */ + /* + * EOTIE enables irq from EOT, SUSP and TXC events. We need to set + * SUSP to acknowledge it later. TXC is automatically cleared + */ + mask |= STM32H7_SPI_SR_SUSP; /* - * When TXTF is set, DXPIE and TXPIE are cleared. So in case of - * Full-Duplex, need to poll RXP event to know if there are remaining - * data, before disabling SPI. + * DXPIE is set in Full-Duplex, one IT will be raised if TXP and RXP + * are set. So in case of Full-Duplex, need to poll TXP and RXP event. */ - if (spi->rx_buf && !spi->cur_usedma) - mask |= STM32H7_SPI_SR_RXP; + if ((spi->cur_comm == SPI_FULL_DUPLEX) && !spi->cur_usedma) + mask |= STM32H7_SPI_SR_TXP | STM32H7_SPI_SR_RXP;
if (!(sr & mask)) { dev_warn(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
From: Kyle Russell bkylerussell@gmail.com
[ Upstream commit 9cf76a72af6ab81030dea6481b1d7bdd814fbdaf ]
These are backwards from Table 7-71 of the TLV320AIC3100 spec [1].
This was broken in 12eb4d66ba2e when BCLK_MASTER and WCLK_MASTER were converted from 0x08 and 0x04 to BIT(2) and BIT(3), respectively.
-#define AIC31XX_BCLK_MASTER 0x08 -#define AIC31XX_WCLK_MASTER 0x04 +#define AIC31XX_BCLK_MASTER BIT(2) +#define AIC31XX_WCLK_MASTER BIT(3)
Probably just a typo since the defines were not listed in bit order.
[1] https://www.ti.com/lit/gpn/tlv320aic3100
Signed-off-by: Kyle Russell bkylerussell@gmail.com Link: https://lore.kernel.org/r/20210622010941.241386-1-bkylerussell@gmail.com Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- sound/soc/codecs/tlv320aic31xx.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/sound/soc/codecs/tlv320aic31xx.h b/sound/soc/codecs/tlv320aic31xx.h index cb024955c978..73c5f6c8ed69 100644 --- a/sound/soc/codecs/tlv320aic31xx.h +++ b/sound/soc/codecs/tlv320aic31xx.h @@ -151,8 +151,8 @@ struct aic31xx_pdata { #define AIC31XX_WORD_LEN_24BITS 0x02 #define AIC31XX_WORD_LEN_32BITS 0x03 #define AIC31XX_IFACE1_MASTER_MASK GENMASK(3, 2) -#define AIC31XX_BCLK_MASTER BIT(2) -#define AIC31XX_WCLK_MASTER BIT(3) +#define AIC31XX_BCLK_MASTER BIT(3) +#define AIC31XX_WCLK_MASTER BIT(2)
/* AIC31XX_DATA_OFFSET */ #define AIC31XX_DATA_OFFSET_MASK GENMASK(7, 0)
From: Takashi Iwai tiwai@suse.de
[ Upstream commit 9c23aa51477a37f8b56c3c40192248db0663c196 ]
rtl8152_close() takes the refcount via usb_autopm_get_interface() but it doesn't release when RTL8152_UNPLUG test hits. This may lead to the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194 Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/r8152.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index 24d124633037..873f288e7cec 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -4317,9 +4317,10 @@ static int rtl8152_close(struct net_device *netdev) tp->rtl_ops.down(tp);
mutex_unlock(&tp->control); + }
+ if (!res) usb_autopm_put_interface(tp->intf); - }
free_all_mem(tp);
From: Jia He justin.he@arm.com
[ Upstream commit 6206b7981a36476f4695d661ae139f7db36a802d ]
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ QL41000 ethernet controller: BUG: scheduling while atomic: kworker/0:4/531/0x00000200 [qed_probe:488()]hw prepare failed kernel BUG at mm/vmalloc.c:2355! Internal error: Oops - BUG: 0 [#1] SMP CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu pstate: 00400009 (nzcv daif +PAN -UAO) Call trace: vunmap+0x4c/0x50 iounmap+0x48/0x58 qed_free_pci+0x60/0x80 [qed] qed_probe+0x35c/0x688 [qed] __qede_probe+0x88/0x5c8 [qede] qede_probe+0x60/0xe0 [qede] local_pci_probe+0x48/0xa0 work_for_cpu_fn+0x24/0x38 process_one_work+0x1d0/0x468 worker_thread+0x238/0x4e0 kthread+0xf0/0x118 ret_from_fork+0x10/0x18
In this case, qed_hw_prepare() returns error due to hw/fw error, but in theory work queue should be in process context instead of interrupt.
The root cause might be the unpaired spin_{un}lock_bh() in _qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly.
Reported-by: Lijian Zhang Lijian.Zhang@arm.com Signed-off-by: Jia He justin.he@arm.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/qlogic/qed/qed_mcp.c | 23 +++++++++++++++++------ 1 file changed, 17 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qed/qed_mcp.c b/drivers/net/ethernet/qlogic/qed/qed_mcp.c index 9401b49275f0..5d85ae59bc51 100644 --- a/drivers/net/ethernet/qlogic/qed/qed_mcp.c +++ b/drivers/net/ethernet/qlogic/qed/qed_mcp.c @@ -498,14 +498,18 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn,
spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
- if (!qed_mcp_has_pending_cmd(p_hwfn)) + if (!qed_mcp_has_pending_cmd(p_hwfn)) { + spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock); break; + }
rc = qed_mcp_update_pending_cmd(p_hwfn, p_ptt); - if (!rc) + if (!rc) { + spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock); break; - else if (rc != -EAGAIN) + } else if (rc != -EAGAIN) { goto err; + }
spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock);
@@ -522,6 +526,8 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn, return -EAGAIN; }
+ spin_lock_bh(&p_hwfn->mcp_info->cmd_lock); + /* Send the mailbox command */ qed_mcp_reread_offsets(p_hwfn, p_ptt); seq_num = ++p_hwfn->mcp_info->drv_mb_seq; @@ -548,14 +554,18 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn,
spin_lock_bh(&p_hwfn->mcp_info->cmd_lock);
- if (p_cmd_elem->b_is_completed) + if (p_cmd_elem->b_is_completed) { + spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock); break; + }
rc = qed_mcp_update_pending_cmd(p_hwfn, p_ptt); - if (!rc) + if (!rc) { + spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock); break; - else if (rc != -EAGAIN) + } else if (rc != -EAGAIN) { goto err; + }
spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock); } while (++cnt < max_retries); @@ -576,6 +586,7 @@ _qed_mcp_cmd_and_union(struct qed_hwfn *p_hwfn, return -EAGAIN; }
+ spin_lock_bh(&p_hwfn->mcp_info->cmd_lock); qed_mcp_cmd_del_elem(p_hwfn, p_cmd_elem); spin_unlock_bh(&p_hwfn->mcp_info->cmd_lock);
From: Eric Woudstra ericwouds@gmail.com
[ Upstream commit 11d8d98cbeef1496469b268d79938b05524731e8 ]
According to reference guides mt7530 (mt7620) and mt7531:
NOTE: When IVL is reset, MAC[47:0] and FID[2:0] will be used to read/write the address table. When IVL is set, MAC[47:0] and CVID[11:0] will be used to read/write the address table.
Since the function only fills in CVID and no FID, we need to set the IVL bit. The existing code does not set it.
This is a fix for the issue I dropped here earlier:
http://lists.infradead.org/pipermail/linux-mediatek/2021-June/025697.html
With this patch, it is now possible to delete the 'self' fdb entry manually. However, wifi roaming still has the same issue, the entry does not get deleted automatically. Wifi roaming also needs a fix somewhere else to function correctly in combination with vlan.
Signed-off-by: Eric Woudstra ericwouds@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/dsa/mt7530.c | 1 + drivers/net/dsa/mt7530.h | 1 + 2 files changed, 2 insertions(+)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index 071e5015bf91..04531b36b217 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -353,6 +353,7 @@ mt7530_fdb_write(struct mt7530_priv *priv, u16 vid, int i;
reg[1] |= vid & CVID_MASK; + reg[1] |= ATA2_IVL; reg[2] |= (aging & AGE_TIMER_MASK) << AGE_TIMER; reg[2] |= (port_mask & PORT_MAP_MASK) << PORT_MAP; /* STATIC_ENT indicate that entry is static wouldn't diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h index 3ef7b5a6fc22..a9ef790578ba 100644 --- a/drivers/net/dsa/mt7530.h +++ b/drivers/net/dsa/mt7530.h @@ -43,6 +43,7 @@ enum { #define STATIC_EMP 0 #define STATIC_ENT 3 #define MT7530_ATA2 0x78 +#define ATA2_IVL BIT(15)
/* Register for address table write data */ #define MT7530_ATWD 0x7c
From: Pravin B Shelar pshelar@ovn.org
[ Upstream commit a17ad0961706244dce48ec941f7e476a38c0e727 ]
In some cases skb head could be locked and entire header data is pulled from skb. When skb_zerocopy() called in such cases, following BUG is triggered. This patch fixes it by copying entire skb in such cases. This could be optimized incase this is performance bottleneck.
---8<--- kernel BUG at net/core/skbuff.c:2961! invalid opcode: 0000 [#1] SMP PTI CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:skb_zerocopy+0x37a/0x3a0 RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246 Call Trace: <IRQ> queue_userspace_packet+0x2af/0x5e0 [openvswitch] ovs_dp_upcall+0x3d/0x60 [openvswitch] ovs_dp_process_packet+0x125/0x150 [openvswitch] ovs_vport_receive+0x77/0xd0 [openvswitch] netdev_port_receive+0x87/0x130 [openvswitch] netdev_frame_hook+0x4b/0x60 [openvswitch] __netif_receive_skb_core+0x2b4/0xc90 __netif_receive_skb_one_core+0x3f/0xa0 __netif_receive_skb+0x18/0x60 process_backlog+0xa9/0x160 net_rx_action+0x142/0x390 __do_softirq+0xe1/0x2d6 irq_exit+0xae/0xb0 do_IRQ+0x5a/0xf0 common_interrupt+0xf/0xf
Code that triggered BUG: int skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen) { int i, j = 0; int plen = 0; /* length of skb->head fragment */ int ret; struct page *page; unsigned int offset;
BUG_ON(!from->head_frag && !hlen);
Signed-off-by: Pravin B Shelar pshelar@ovn.org Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- net/core/skbuff.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/net/core/skbuff.c b/net/core/skbuff.c index 99d6f4d1297c..7dba091bc861 100644 --- a/net/core/skbuff.c +++ b/net/core/skbuff.c @@ -2921,8 +2921,11 @@ skb_zerocopy_headlen(const struct sk_buff *from)
if (!from->head_frag || skb_headlen(from) < L1_CACHE_BYTES || - skb_shinfo(from)->nr_frags >= MAX_SKB_FRAGS) + skb_shinfo(from)->nr_frags >= MAX_SKB_FRAGS) { hlen = skb_headlen(from); + if (!hlen) + hlen = from->len; + }
if (skb_has_frag_list(from)) hlen = from->len;
From: Keith Busch kbusch@kernel.org
[ Upstream commit 234211b8dd161fa25f192c78d5a8d2dd6bf920a0 ]
The metadata address is set after the trace event, so the trace is not capturing anything useful. Rather than logging the memory address, it's useful to know if the command carries a metadata payload, so change the trace event to log that true/false state instead.
Signed-off-by: Keith Busch kbusch@kernel.org Signed-off-by: Christoph Hellwig hch@lst.de Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/trace.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/nvme/host/trace.h b/drivers/nvme/host/trace.h index daaf700eae79..35bac7a25422 100644 --- a/drivers/nvme/host/trace.h +++ b/drivers/nvme/host/trace.h @@ -56,7 +56,7 @@ TRACE_EVENT(nvme_setup_cmd, __field(u8, fctype) __field(u16, cid) __field(u32, nsid) - __field(u64, metadata) + __field(bool, metadata) __array(u8, cdw10, 24) ), TP_fast_assign( @@ -66,13 +66,13 @@ TRACE_EVENT(nvme_setup_cmd, __entry->flags = cmd->common.flags; __entry->cid = cmd->common.command_id; __entry->nsid = le32_to_cpu(cmd->common.nsid); - __entry->metadata = le64_to_cpu(cmd->common.metadata); + __entry->metadata = !!blk_integrity_rq(req); __entry->fctype = cmd->fabrics.fctype; __assign_disk_name(__entry->disk, req->rq_disk); memcpy(__entry->cdw10, &cmd->common.cdw10, sizeof(__entry->cdw10)); ), - TP_printk("nvme%d: %sqid=%d, cmdid=%u, nsid=%u, flags=0x%x, meta=0x%llx, cmd=(%s %s)", + TP_printk("nvme%d: %sqid=%d, cmdid=%u, nsid=%u, flags=0x%x, meta=0x%x, cmd=(%s %s)", __entry->ctrl_id, __print_disk_name(__entry->disk), __entry->qid, __entry->cid, __entry->nsid, __entry->flags, __entry->metadata,
From: Linus Torvalds torvalds@linux-foundation.org
[ Upstream commit fc68f42aa737dc15e7665a4101d4168aadb8e4c4 ]
Commit 71f642833284 ("ACPI: utils: Fix reference counting in for_each_acpi_dev_match()") started doing "acpi_dev_put()" on a pointer that was possibly NULL. That fails miserably, because that helper inline function is not set up to handle that case.
Just make acpi_dev_put() silently accept a NULL pointer, rather than calling down to put_device() with an invalid offset off that NULL pointer.
Link: https://lore.kernel.org/lkml/a607c149-6bf6-0fd0-0e31-100378504da2@kernel.dk/ Reported-and-tested-by: Jens Axboe axboe@kernel.dk Tested-by: Daniel Scally djrscally@gmail.com Cc: Andy Shevchenko andy.shevchenko@gmail.com Signed-off-by: Linus Torvalds torvalds@linux-foundation.org Signed-off-by: Sasha Levin sashal@kernel.org --- include/acpi/acpi_bus.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/include/acpi/acpi_bus.h b/include/acpi/acpi_bus.h index 4d67a67964fa..1e5ae3b01eb2 100644 --- a/include/acpi/acpi_bus.h +++ b/include/acpi/acpi_bus.h @@ -681,7 +681,8 @@ acpi_dev_get_first_match_dev(const char *hid, const char *uid, s64 hrv);
static inline void acpi_dev_put(struct acpi_device *adev) { - put_device(&adev->dev); + if (adev) + put_device(&adev->dev); } #else /* CONFIG_ACPI */
linux-stable-mirror@lists.linaro.org