From: Hanjun Guo guohanjun@huawei.com

[ Upstream commit 7eb48dd094de5fe0e216b550e73aa85257903973 ]

The acpi_get_table() should be coupled with acpi_put_table() if the mapped table is not used at runtime to release the table mapping, put the CSRT table buf after using it.

Signed-off-by: Hanjun Guo guohanjun@huawei.com Link: https://lore.kernel.org/r/1595411661-15936-1-git-send-email-guohanjun@huawei... Signed-off-by: Vinod Koul vkoul@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/dma/acpi-dma.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/dma/acpi-dma.c b/drivers/dma/acpi-dma.c index 8a05db3343d39..dcbcb712de6e8 100644 --- a/drivers/dma/acpi-dma.c +++ b/drivers/dma/acpi-dma.c @@ -135,11 +135,13 @@ static void acpi_dma_parse_csrt(struct acpi_device *adev, struct acpi_dma *adma) if (ret < 0) { dev_warn(&adev->dev, "error in parsing resource group\n"); - return; + break; }

grp = (struct acpi_csrt_group *)((void *)grp + grp->length); } + + acpi_put_table((struct acpi_table_header *)csrt); }

/**

From: Florian Westphal fw@strlen.de

[ Upstream commit cc5453a5b7e90c39f713091a7ebc53c1f87d1700 ]

If an sctp connection gets re-used, heartbeats are flagged as invalid because their vtag doesn't match.

Handle this in a similar way as TCP conntrack when it suspects that the endpoints and conntrack are out-of-sync.

When a HEARTBEAT request fails its vtag validation, flag this in the conntrack state and accept the packet.

When a HEARTBEAT_ACK is received with an invalid vtag in the reverse direction after we allowed such a HEARTBEAT through, assume we are out-of-sync and re-set the vtag info.

v2: remove left-over snippet from an older incarnation that moved new_state/old_state assignments, thats not needed so keep that as-is.

Signed-off-by: Florian Westphal fw@strlen.de Signed-off-by: Pablo Neira Ayuso pablo@netfilter.org Signed-off-by: Sasha Levin sashal@kernel.org --- include/linux/netfilter/nf_conntrack_sctp.h | 2 ++ net/netfilter/nf_conntrack_proto_sctp.c | 39 ++++++++++++++++++--- 2 files changed, 37 insertions(+), 4 deletions(-)

diff --git a/include/linux/netfilter/nf_conntrack_sctp.h b/include/linux/netfilter/nf_conntrack_sctp.h index 9a33f171aa822..625f491b95de8 100644 --- a/include/linux/netfilter/nf_conntrack_sctp.h +++ b/include/linux/netfilter/nf_conntrack_sctp.h @@ -9,6 +9,8 @@ struct ip_ct_sctp { enum sctp_conntrack state;

__be32 vtag[IP_CT_DIR_MAX]; + u8 last_dir; + u8 flags; };

#endif /* _NF_CONNTRACK_SCTP_H */ diff --git a/net/netfilter/nf_conntrack_proto_sctp.c b/net/netfilter/nf_conntrack_proto_sctp.c index 4f897b14b6069..810cca24b3990 100644 --- a/net/netfilter/nf_conntrack_proto_sctp.c +++ b/net/netfilter/nf_conntrack_proto_sctp.c @@ -62,6 +62,8 @@ static const unsigned int sctp_timeouts[SCTP_CONNTRACK_MAX] = { [SCTP_CONNTRACK_HEARTBEAT_ACKED] = 210 SECS, };

+#define SCTP_FLAG_HEARTBEAT_VTAG_FAILED 1 + #define sNO SCTP_CONNTRACK_NONE #define sCL SCTP_CONNTRACK_CLOSED #define sCW SCTP_CONNTRACK_COOKIE_WAIT @@ -369,6 +371,7 @@ int nf_conntrack_sctp_packet(struct nf_conn *ct, u_int32_t offset, count; unsigned int *timeouts; unsigned long map[256 / sizeof(unsigned long)] = { 0 }; + bool ignore = false;

if (sctp_error(skb, dataoff, state)) return -NF_ACCEPT; @@ -427,15 +430,39 @@ int nf_conntrack_sctp_packet(struct nf_conn *ct, /* Sec 8.5.1 (D) */ if (sh->vtag != ct->proto.sctp.vtag[dir]) goto out_unlock; - } else if (sch->type == SCTP_CID_HEARTBEAT || - sch->type == SCTP_CID_HEARTBEAT_ACK) { + } else if (sch->type == SCTP_CID_HEARTBEAT) { + if (ct->proto.sctp.vtag[dir] == 0) { + pr_debug("Setting %d vtag %x for dir %d\n", sch->type, sh->vtag, dir); + ct->proto.sctp.vtag[dir] = sh->vtag; + } else if (sh->vtag != ct->proto.sctp.vtag[dir]) { + if (test_bit(SCTP_CID_DATA, map) || ignore) + goto out_unlock; + + ct->proto.sctp.flags |= SCTP_FLAG_HEARTBEAT_VTAG_FAILED; + ct->proto.sctp.last_dir = dir; + ignore = true; + continue; + } else if (ct->proto.sctp.flags & SCTP_FLAG_HEARTBEAT_VTAG_FAILED) { + ct->proto.sctp.flags &= ~SCTP_FLAG_HEARTBEAT_VTAG_FAILED; + } + } else if (sch->type == SCTP_CID_HEARTBEAT_ACK) { if (ct->proto.sctp.vtag[dir] == 0) { pr_debug("Setting vtag %x for dir %d\n", sh->vtag, dir); ct->proto.sctp.vtag[dir] = sh->vtag; } else if (sh->vtag != ct->proto.sctp.vtag[dir]) { - pr_debug("Verification tag check failed\n"); - goto out_unlock; + if (test_bit(SCTP_CID_DATA, map) || ignore) + goto out_unlock; + + if ((ct->proto.sctp.flags & SCTP_FLAG_HEARTBEAT_VTAG_FAILED) == 0 || + ct->proto.sctp.last_dir == dir) + goto out_unlock; + + ct->proto.sctp.flags &= ~SCTP_FLAG_HEARTBEAT_VTAG_FAILED; + ct->proto.sctp.vtag[dir] = sh->vtag; + ct->proto.sctp.vtag[!dir] = 0; + } else if (ct->proto.sctp.flags & SCTP_FLAG_HEARTBEAT_VTAG_FAILED) { + ct->proto.sctp.flags &= ~SCTP_FLAG_HEARTBEAT_VTAG_FAILED; } }

@@ -470,6 +497,10 @@ int nf_conntrack_sctp_packet(struct nf_conn *ct, } spin_unlock_bh(&ct->lock);

+ /* allow but do not refresh timeout */ + if (ignore) + return NF_ACCEPT; + timeouts = nf_ct_timeout_lookup(ct); if (!timeouts) timeouts = nf_sctp_pernet(nf_ct_net(ct))->timeouts;

From: Stefano Brivio sbrivio@redhat.com

[ Upstream commit 0726763043dc10dd4c12481f050b1a5ef8f15410 ]

Getting creative with nft and omitting the interval_overlap() check from the set_overlap() function, without omitting set_overlap() altogether, led to the observation of a partial overlap that wasn't detected, and would actually result in replacement of the end element of an existing interval.

This is due to the fact that we'll return -EEXIST on a matching, pre-existing start element, instead of -ENOTEMPTY, and the error is cleared by API if NLM_F_EXCL is not given. At this point, we can insert a matching start, and duplicate the end element as long as we don't end up into other intervals.

For instance, inserting interval 0 - 2 with an existing 0 - 3 interval would result in a single 0 - 2 interval, and a dangling '3' end element. This is because nft will proceed after inserting the '0' start element as no error is reported, and no further conflicting intervals are detected on insertion of the end element.

This needs a different approach as it's a local condition that can be detected by looking for duplicate ends coming from left and right, separately. Track those and directly report -ENOTEMPTY on duplicated end elements for a matching start.

Signed-off-by: Stefano Brivio sbrivio@redhat.com Signed-off-by: Pablo Neira Ayuso pablo@netfilter.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/netfilter/nft_set_rbtree.c | 34 +++++++++++++++++++++++++++++++++- 1 file changed, 33 insertions(+), 1 deletion(-)

diff --git a/net/netfilter/nft_set_rbtree.c b/net/netfilter/nft_set_rbtree.c index b85ce6f0c0a6f..f317ad80cd6bc 100644 --- a/net/netfilter/nft_set_rbtree.c +++ b/net/netfilter/nft_set_rbtree.c @@ -218,11 +218,11 @@ static int __nft_rbtree_insert(const struct net *net, const struct nft_set *set, struct nft_rbtree_elem *new, struct nft_set_ext **ext) { + bool overlap = false, dup_end_left = false, dup_end_right = false; struct nft_rbtree *priv = nft_set_priv(set); u8 genmask = nft_genmask_next(net); struct nft_rbtree_elem *rbe; struct rb_node *parent, **p; - bool overlap = false; int d;

/* Detect overlaps as we descend the tree. Set the flag in these cases: @@ -262,6 +262,20 @@ static int __nft_rbtree_insert(const struct net *net, const struct nft_set *set, * * which always happen as last step and imply that no further * overlapping is possible. + * + * Another special case comes from the fact that start elements matching + * an already existing start element are allowed: insertion is not + * performed but we return -EEXIST in that case, and the error will be + * cleared by the caller if NLM_F_EXCL is not present in the request. + * This way, request for insertion of an exact overlap isn't reported as + * error to userspace if not desired. + * + * However, if the existing start matches a pre-existing start, but the + * end element doesn't match the corresponding pre-existing end element, + * we need to report a partial overlap. This is a local condition that + * can be noticed without need for a tracking flag, by checking for a + * local duplicated end for a corresponding start, from left and right, + * separately. */

parent = NULL; @@ -281,19 +295,35 @@ static int __nft_rbtree_insert(const struct net *net, const struct nft_set *set, !nft_set_elem_expired(&rbe->ext) && !*p) overlap = false; } else { + if (dup_end_left && !*p) + return -ENOTEMPTY; + overlap = nft_rbtree_interval_end(rbe) && nft_set_elem_active(&rbe->ext, genmask) && !nft_set_elem_expired(&rbe->ext); + + if (overlap) { + dup_end_right = true; + continue; + } } } else if (d > 0) { p = &parent->rb_right;

if (nft_rbtree_interval_end(new)) { + if (dup_end_right && !*p) + return -ENOTEMPTY; + overlap = nft_rbtree_interval_end(rbe) && nft_set_elem_active(&rbe->ext, genmask) && !nft_set_elem_expired(&rbe->ext); + + if (overlap) { + dup_end_left = true; + continue; + } } else if (nft_set_elem_active(&rbe->ext, genmask) && !nft_set_elem_expired(&rbe->ext)) { overlap = nft_rbtree_interval_end(rbe); @@ -321,6 +351,8 @@ static int __nft_rbtree_insert(const struct net *net, const struct nft_set *set, p = &parent->rb_left; } } + + dup_end_left = dup_end_right = false; }

if (overlap)

From: Dinghao Liu dinghao.liu@zju.edu.cn

[ Upstream commit f97c04c316d8fea16dca449fdfbe101fbdfee6a2 ]

When down_killable() fails, skb_resp should be freed just like when st95hf_spi_send() fails.

Signed-off-by: Dinghao Liu dinghao.liu@zju.edu.cn Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nfc/st95hf/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/nfc/st95hf/core.c b/drivers/nfc/st95hf/core.c index 9642971e89cea..4578547659839 100644 --- a/drivers/nfc/st95hf/core.c +++ b/drivers/nfc/st95hf/core.c @@ -966,7 +966,7 @@ static int st95hf_in_send_cmd(struct nfc_digital_dev *ddev, rc = down_killable(&stcontext->exchange_lock); if (rc) { WARN(1, "Semaphore is not found up in st95hf_in_send_cmd\n"); - return rc; + goto free_skb_resp; }

rc = st95hf_spi_send(&stcontext->spicontext, skb->data,

From: Ye Bin yebin10@huawei.com

[ Upstream commit f308a35f547cd7c1d8a901c12b3ac508e96df665 ]

Link: https://lore.kernel.org/r/20200824033436.45570-1-yebin10@huawei.com Acked-by: Saurav Kashyap skashyap@marvell.com Signed-off-by: Ye Bin yebin10@huawei.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/qedf/qedf_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/scsi/qedf/qedf_main.c b/drivers/scsi/qedf/qedf_main.c index 36b1ca2dadbb5..51cfab9d1afdc 100644 --- a/drivers/scsi/qedf/qedf_main.c +++ b/drivers/scsi/qedf/qedf_main.c @@ -3843,7 +3843,7 @@ void qedf_stag_change_work(struct work_struct *work) container_of(work, struct qedf_ctx, stag_work.work);

if (!qedf) { - QEDF_ERR(&qedf->dbg_ctx, "qedf is NULL"); + QEDF_ERR(NULL, "qedf is NULL"); return; } QEDF_ERR(&qedf->dbg_ctx, "Performing software context reset.\n");

From: Mohan Kumar mkumard@nvidia.com

[ Upstream commit 23d63a31d9f44d7daeac0d1fb65c6a73c70e5216 ]

The WAKEEN bits are used to indicate which bits in the STATESTS register may cause wake event during the codec state change request. Configure the WAKEEN register for the Tegra to detect the wake events.

Signed-off-by: Mohan Kumar mkumard@nvidia.com Acked-by: Sameer Pujar spujar@nvidia.com Link: https://lore.kernel.org/r/20200825052415.20626-3-mkumard@nvidia.com Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Sasha Levin sashal@kernel.org --- sound/pci/hda/hda_tegra.c | 7 +++++++ 1 file changed, 7 insertions(+)

diff --git a/sound/pci/hda/hda_tegra.c b/sound/pci/hda/hda_tegra.c index 0cc5fad1af8a9..ae40ca3f29837 100644 --- a/sound/pci/hda/hda_tegra.c +++ b/sound/pci/hda/hda_tegra.c @@ -179,6 +179,10 @@ static int __maybe_unused hda_tegra_runtime_suspend(struct device *dev) struct hda_tegra *hda = container_of(chip, struct hda_tegra, chip);

if (chip && chip->running) { + /* enable controller wake up event */ + azx_writew(chip, WAKEEN, azx_readw(chip, WAKEEN) | + STATESTS_INT_MASK); + azx_stop_chip(chip); azx_enter_link_reset(chip); } @@ -200,6 +204,9 @@ static int __maybe_unused hda_tegra_runtime_resume(struct device *dev) if (chip && chip->running) { hda_tegra_init(hda); azx_init_chip(chip, 1); + /* disable controller wake up event*/ + azx_writew(chip, WAKEEN, azx_readw(chip, WAKEEN) & + ~STATESTS_INT_MASK); }

return 0;

From: Mingming Cao mmc@linux.vnet.ibm.com

[ Upstream commit 9f13457377907fa253aef560e1a37e1ca4197f9b ]

At the time of do_rest, ibmvnic tries to re-initalize the tx_pools and rx_pools to avoid re-allocating the long term buffer. However there is a window inside do_reset that the tx_pools and rx_pools were freed before re-initialized making it possible to deference null pointers.

This patch fix this issue by always check the tx_pool and rx_pool are not NULL after ibmvnic_login. If so, re-allocating the pools. This will avoid getting into calling reset_tx/rx_pools with NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.

Signed-off-by: Mingming Cao mmc@linux.vnet.ibm.com Signed-off-by: Dany Madden drt@linux.ibm.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/ibm/ibmvnic.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/ibm/ibmvnic.c b/drivers/net/ethernet/ibm/ibmvnic.c index 5afb3c9c52d20..d3a774331afc7 100644 --- a/drivers/net/ethernet/ibm/ibmvnic.c +++ b/drivers/net/ethernet/ibm/ibmvnic.c @@ -479,6 +479,9 @@ static int reset_rx_pools(struct ibmvnic_adapter *adapter) int i, j, rc; u64 *size_array;

+ if (!adapter->rx_pool) + return -1; + size_array = (u64 *)((u8 *)(adapter->login_rsp_buf) + be32_to_cpu(adapter->login_rsp_buf->off_rxadd_buff_size));

@@ -649,6 +652,9 @@ static int reset_tx_pools(struct ibmvnic_adapter *adapter) int tx_scrqs; int i, rc;

+ if (!adapter->tx_pool) + return -1; + tx_scrqs = be32_to_cpu(adapter->login_rsp_buf->num_txsubm_subcrqs); for (i = 0; i < tx_scrqs; i++) { rc = reset_one_tx_pool(adapter, &adapter->tso_pool[i]); @@ -2011,7 +2017,10 @@ static int do_reset(struct ibmvnic_adapter *adapter, adapter->req_rx_add_entries_per_subcrq != old_num_rx_slots || adapter->req_tx_entries_per_subcrq != - old_num_tx_slots) { + old_num_tx_slots || + !adapter->rx_pool || + !adapter->tso_pool || + !adapter->tx_pool) { release_rx_pools(adapter); release_tx_pools(adapter); release_napi(adapter); @@ -2024,10 +2033,14 @@ static int do_reset(struct ibmvnic_adapter *adapter, } else { rc = reset_tx_pools(adapter); if (rc) + netdev_dbg(adapter->netdev, "reset tx pools failed (%d)\n", + rc); goto out;

rc = reset_rx_pools(adapter); if (rc) + netdev_dbg(adapter->netdev, "reset rx pools failed (%d)\n", + rc); goto out; } ibmvnic_disable_irqs(adapter);

From: Brian Foster bfoster@redhat.com

[ Upstream commit 657f101930bc6c5b41bd7d6c22565c4302a80d33 ]

The inode chunk allocation transaction reserves inobt_maxlevels-1 blocks to accommodate a full split of the inode btree. A full split requires an allocation for every existing level and a new root block, which means inobt_maxlevels is the worst case block requirement for a transaction that inserts to the inobt. This can lead to a transaction block reservation overrun when tmpfile creation allocates an inode chunk and expands the inobt to its maximum depth. This problem has been observed in conjunction with overlayfs, which makes frequent use of tmpfiles internally.

The existing reservation code goes back as far as the Linux git repo history (v2.6.12). It was likely never observed as a problem because the traditional file/directory creation transactions also include worst case block reservation for directory modifications, which most likely is able to make up for a single block deficiency in the inode allocation portion of the calculation. tmpfile support is relatively more recent (v3.15), less heavily used, and only includes the inode allocation block reservation as tmpfiles aren't linked into the directory tree on creation.

Fix up the inode alloc block reservation macro and a couple of the block allocator minleft parameters that enforce an allocation to leave enough free blocks in the AG for a full inobt split.

Signed-off-by: Brian Foster bfoster@redhat.com Reviewed-by: Darrick J. Wong darrick.wong@oracle.com Signed-off-by: Darrick J. Wong darrick.wong@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- fs/xfs/libxfs/xfs_ialloc.c | 4 ++-- fs/xfs/libxfs/xfs_trans_space.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/fs/xfs/libxfs/xfs_ialloc.c b/fs/xfs/libxfs/xfs_ialloc.c index 7fcf62b324b0d..8c1a7cc484b65 100644 --- a/fs/xfs/libxfs/xfs_ialloc.c +++ b/fs/xfs/libxfs/xfs_ialloc.c @@ -688,7 +688,7 @@ xfs_ialloc_ag_alloc( args.minalignslop = igeo->cluster_align - 1;

/* Allow space for the inode btree to split. */ - args.minleft = igeo->inobt_maxlevels - 1; + args.minleft = igeo->inobt_maxlevels; if ((error = xfs_alloc_vextent(&args))) return error;

@@ -736,7 +736,7 @@ xfs_ialloc_ag_alloc( /* * Allow space for the inode btree to split. */ - args.minleft = igeo->inobt_maxlevels - 1; + args.minleft = igeo->inobt_maxlevels; if ((error = xfs_alloc_vextent(&args))) return error; } diff --git a/fs/xfs/libxfs/xfs_trans_space.h b/fs/xfs/libxfs/xfs_trans_space.h index c6df01a2a1585..7ad3659c5d2a9 100644 --- a/fs/xfs/libxfs/xfs_trans_space.h +++ b/fs/xfs/libxfs/xfs_trans_space.h @@ -58,7 +58,7 @@ #define XFS_IALLOC_SPACE_RES(mp) \ (M_IGEO(mp)->ialloc_blks + \ ((xfs_sb_version_hasfinobt(&mp->m_sb) ? 2 : 1) * \ - (M_IGEO(mp)->inobt_maxlevels - 1))) + M_IGEO(mp)->inobt_maxlevels))

/* * Space reservation values for various transactions.

From: Shay Bar shay.bar@celeno.com

[ Upstream commit 3579994476b65cb5e272ff0f720a1fd31322e53f ]

Fix cfg80211_chandef_usable(): consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz.

Based on: "Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW Support subfield at a STA transmitting the VHT Capabilities Information field"

From "Draft P802.11REVmd_D3.0.pdf"

Signed-off-by: Aviad Brikman aviad.brikman@celeno.com Signed-off-by: Shay Bar shay.bar@celeno.com Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com [reformat the code a bit and use u32_get_bits()] Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/wireless/chan.c | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/net/wireless/chan.c b/net/wireless/chan.c index cddf92c5d09ef..7a7cc4ade2b36 100644 --- a/net/wireless/chan.c +++ b/net/wireless/chan.c @@ -10,6 +10,7 @@ */

#include <linux/export.h> +#include <linux/bitfield.h> #include <net/cfg80211.h> #include "core.h" #include "rdev-ops.h" @@ -892,6 +893,7 @@ bool cfg80211_chandef_usable(struct wiphy *wiphy, struct ieee80211_sta_vht_cap *vht_cap; struct ieee80211_edmg *edmg_cap; u32 width, control_freq, cap; + bool support_80_80 = false;

if (WARN_ON(!cfg80211_chandef_valid(chandef))) return false; @@ -944,9 +946,13 @@ bool cfg80211_chandef_usable(struct wiphy *wiphy, return false; break; case NL80211_CHAN_WIDTH_80P80: - cap = vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK; - if (chandef->chan->band != NL80211_BAND_6GHZ && - cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ) + cap = vht_cap->cap; + support_80_80 = + (cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ) || + (cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ && + cap & IEEE80211_VHT_CAP_EXT_NSS_BW_MASK) || + u32_get_bits(cap, IEEE80211_VHT_CAP_EXT_NSS_BW_MASK) > 1; + if (chandef->chan->band != NL80211_BAND_6GHZ && !support_80_80) return false; /* fall through */ case NL80211_CHAN_WIDTH_80: @@ -966,7 +972,8 @@ bool cfg80211_chandef_usable(struct wiphy *wiphy, return false; cap = vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK; if (cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ && - cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ) + cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ && + !(vht_cap->cap & IEEE80211_VHT_CAP_EXT_NSS_BW_MASK)) return false; break; default:

From: Felix Fietkau nbd@nbd.name

[ Upstream commit 47df8e059b49a80c179fae39256bcd7096810934 ]

When running a large number of packets per second with a high data rate and long A-MPDUs, the packet loss threshold can be reached very quickly when the link conditions change. This frequently shows up as spurious disconnects. Mitigate false positives by using a similar logic for regular stations as the one being used for TDLS, though with a more aggressive timeout. Packet loss events are only reported if no ACK was received for a second.

Signed-off-by: Felix Fietkau nbd@nbd.name Link: https://lore.kernel.org/r/20200808172542.41628-1-nbd@nbd.name Signed-off-by: Johannes Berg johannes.berg@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/mac80211/sta_info.h | 4 ++-- net/mac80211/status.c | 31 +++++++++++++++---------------- 2 files changed, 17 insertions(+), 18 deletions(-)

diff --git a/net/mac80211/sta_info.h b/net/mac80211/sta_info.h index 49728047dfad6..f66fcce8e6a45 100644 --- a/net/mac80211/sta_info.h +++ b/net/mac80211/sta_info.h @@ -522,7 +522,7 @@ struct ieee80211_sta_rx_stats { * @status_stats.retry_failed: # of frames that failed after retry * @status_stats.retry_count: # of retries attempted * @status_stats.lost_packets: # of lost packets - * @status_stats.last_tdls_pkt_time: timestamp of last TDLS packet + * @status_stats.last_pkt_time: timestamp of last ACKed packet * @status_stats.msdu_retries: # of MSDU retries * @status_stats.msdu_failed: # of failed MSDUs * @status_stats.last_ack: last ack timestamp (jiffies) @@ -595,7 +595,7 @@ struct sta_info { unsigned long filtered; unsigned long retry_failed, retry_count; unsigned int lost_packets; - unsigned long last_tdls_pkt_time; + unsigned long last_pkt_time; u64 msdu_retries[IEEE80211_NUM_TIDS + 1]; u64 msdu_failed[IEEE80211_NUM_TIDS + 1]; unsigned long last_ack; diff --git a/net/mac80211/status.c b/net/mac80211/status.c index cbc40b358ba26..819c4221c284e 100644 --- a/net/mac80211/status.c +++ b/net/mac80211/status.c @@ -755,12 +755,16 @@ static void ieee80211_report_used_skb(struct ieee80211_local *local, * - current throughput (higher value for higher tpt)? */ #define STA_LOST_PKT_THRESHOLD 50 +#define STA_LOST_PKT_TIME HZ /* 1 sec since last ACK */ #define STA_LOST_TDLS_PKT_THRESHOLD 10 #define STA_LOST_TDLS_PKT_TIME (10*HZ) /* 10secs since last ACK */

static void ieee80211_lost_packet(struct sta_info *sta, struct ieee80211_tx_info *info) { + unsigned long pkt_time = STA_LOST_PKT_TIME; + unsigned int pkt_thr = STA_LOST_PKT_THRESHOLD; + /* If driver relies on its own algorithm for station kickout, skip * mac80211 packet loss mechanism. */ @@ -773,21 +777,20 @@ static void ieee80211_lost_packet(struct sta_info *sta, return;

sta->status_stats.lost_packets++; - if (!sta->sta.tdls && - sta->status_stats.lost_packets < STA_LOST_PKT_THRESHOLD) - return; + if (sta->sta.tdls) { + pkt_time = STA_LOST_TDLS_PKT_TIME; + pkt_thr = STA_LOST_PKT_THRESHOLD; + }

/* * If we're in TDLS mode, make sure that all STA_LOST_TDLS_PKT_THRESHOLD * of the last packets were lost, and that no ACK was received in the * last STA_LOST_TDLS_PKT_TIME ms, before triggering the CQM packet-loss * mechanism. + * For non-TDLS, use STA_LOST_PKT_THRESHOLD and STA_LOST_PKT_TIME */ - if (sta->sta.tdls && - (sta->status_stats.lost_packets < STA_LOST_TDLS_PKT_THRESHOLD || - time_before(jiffies, - sta->status_stats.last_tdls_pkt_time + - STA_LOST_TDLS_PKT_TIME))) + if (sta->status_stats.lost_packets < pkt_thr || + !time_after(jiffies, sta->status_stats.last_pkt_time + pkt_time)) return;

cfg80211_cqm_pktloss_notify(sta->sdata->dev, sta->sta.addr, @@ -1035,9 +1038,7 @@ static void __ieee80211_tx_status(struct ieee80211_hw *hw, sta->status_stats.lost_packets = 0;

/* Track when last TDLS packet was ACKed */ - if (test_sta_flag(sta, WLAN_STA_TDLS_PEER_AUTH)) - sta->status_stats.last_tdls_pkt_time = - jiffies; + sta->status_stats.last_pkt_time = jiffies; } else if (noack_success) { /* nothing to do here, do not account as lost */ } else { @@ -1170,9 +1171,8 @@ void ieee80211_tx_status_ext(struct ieee80211_hw *hw, if (sta->status_stats.lost_packets) sta->status_stats.lost_packets = 0;

- /* Track when last TDLS packet was ACKed */ - if (test_sta_flag(sta, WLAN_STA_TDLS_PEER_AUTH)) - sta->status_stats.last_tdls_pkt_time = jiffies; + /* Track when last packet was ACKed */ + sta->status_stats.last_pkt_time = jiffies; } else if (test_sta_flag(sta, WLAN_STA_PS_STA)) { return; } else if (noack_success) { @@ -1261,8 +1261,7 @@ void ieee80211_tx_status_8023(struct ieee80211_hw *hw, if (sta->status_stats.lost_packets) sta->status_stats.lost_packets = 0;

- if (test_sta_flag(sta, WLAN_STA_TDLS_PEER_AUTH)) - sta->status_stats.last_tdls_pkt_time = jiffies; + sta->status_stats.last_pkt_time = jiffies; } else { ieee80211_lost_packet(sta, info); }

From: Himadri Pandya himadrispandya@gmail.com

[ Upstream commit a092b7233f0e000cc6f2c71a49e2ecc6f917a5fc ]

The buffer size is 2 Bytes and we expect to receive the same amount of data. But sometimes we receive less data and run into uninit-was-stored issue upon read. Hence modify the error check on the return value to match with the buffer size as a prevention.

Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com Signed-off-by: Himadri Pandya himadrispandya@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/asix_common.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c index e39f41efda3ec..7bc6e8f856fe0 100644 --- a/drivers/net/usb/asix_common.c +++ b/drivers/net/usb/asix_common.c @@ -296,7 +296,7 @@ int asix_read_phy_addr(struct usbnet *dev, int internal)

netdev_dbg(dev->net, "asix_get_phy_addr()\n");

- if (ret < 0) { + if (ret < 2) { netdev_err(dev->net, "Error reading PHYID register: %02x\n", ret); goto out; }

From: Vineet Gupta vgupta@synopsys.com

[ Upstream commit e5c388b4b967037a0e00b60194b0dbcf94881a9b ]

when working on ARC64, spotted an issue in ARCv2 reg file printing. print_reg_file() assumes contiguous reg-file whereas in ARCv2 they are not: r12 comes before r0-r11 due to hardware auto-save. Apparently this issue has been present since v2 port submission.

To avoid bolting hacks for this discontinuity while looping through pt_regs, just ditching the loop and print pt_regs directly.

Signed-off-by: Vineet Gupta vgupta@synopsys.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arc/kernel/troubleshoot.c | 77 +++++++++++++--------------------- 1 file changed, 30 insertions(+), 47 deletions(-)

diff --git a/arch/arc/kernel/troubleshoot.c b/arch/arc/kernel/troubleshoot.c index 28e8bf04b253f..a331bb5d8319f 100644 --- a/arch/arc/kernel/troubleshoot.c +++ b/arch/arc/kernel/troubleshoot.c @@ -18,44 +18,37 @@

#define ARC_PATH_MAX 256

-/* - * Common routine to print scratch regs (r0-r12) or callee regs (r13-r25) - * -Prints 3 regs per line and a CR. - * -To continue, callee regs right after scratch, special handling of CR - */ -static noinline void print_reg_file(long *reg_rev, int start_num) +static noinline void print_regs_scratch(struct pt_regs *regs) { - unsigned int i; - char buf[512]; - int n = 0, len = sizeof(buf); - - for (i = start_num; i < start_num + 13; i++) { - n += scnprintf(buf + n, len - n, "r%02u: 0x%08lx\t", - i, (unsigned long)*reg_rev); - - if (((i + 1) % 3) == 0) - n += scnprintf(buf + n, len - n, "\n"); - - /* because pt_regs has regs reversed: r12..r0, r25..r13 */ - if (is_isa_arcv2() && start_num == 0) - reg_rev++; - else - reg_rev--; - } - - if (start_num != 0) - n += scnprintf(buf + n, len - n, "\n\n"); + pr_cont("BTA: 0x%08lx\n SP: 0x%08lx FP: 0x%08lx BLK: %pS\n", + regs->bta, regs->sp, regs->fp, (void *)regs->blink); + pr_cont("LPS: 0x%08lx\tLPE: 0x%08lx\tLPC: 0x%08lx\n", + regs->lp_start, regs->lp_end, regs->lp_count);

- /* To continue printing callee regs on same line as scratch regs */ - if (start_num == 0) - pr_info("%s", buf); - else - pr_cont("%s\n", buf); + pr_info("r00: 0x%08lx\tr01: 0x%08lx\tr02: 0x%08lx\n" \ + "r03: 0x%08lx\tr04: 0x%08lx\tr05: 0x%08lx\n" \ + "r06: 0x%08lx\tr07: 0x%08lx\tr08: 0x%08lx\n" \ + "r09: 0x%08lx\tr10: 0x%08lx\tr11: 0x%08lx\n" \ + "r12: 0x%08lx\t", + regs->r0, regs->r1, regs->r2, + regs->r3, regs->r4, regs->r5, + regs->r6, regs->r7, regs->r8, + regs->r9, regs->r10, regs->r11, + regs->r12); }

-static void show_callee_regs(struct callee_regs *cregs) +static void print_regs_callee(struct callee_regs *regs) { - print_reg_file(&(cregs->r13), 13); + pr_cont("r13: 0x%08lx\tr14: 0x%08lx\n" \ + "r15: 0x%08lx\tr16: 0x%08lx\tr17: 0x%08lx\n" \ + "r18: 0x%08lx\tr19: 0x%08lx\tr20: 0x%08lx\n" \ + "r21: 0x%08lx\tr22: 0x%08lx\tr23: 0x%08lx\n" \ + "r24: 0x%08lx\tr25: 0x%08lx\n", + regs->r13, regs->r14, + regs->r15, regs->r16, regs->r17, + regs->r18, regs->r19, regs->r20, + regs->r21, regs->r22, regs->r23, + regs->r24, regs->r25); }

static void print_task_path_n_nm(struct task_struct *tsk) @@ -175,7 +168,7 @@ static void show_ecr_verbose(struct pt_regs *regs) void show_regs(struct pt_regs *regs) { struct task_struct *tsk = current; - struct callee_regs *cregs; + struct callee_regs *cregs = (struct callee_regs *)tsk->thread.callee_reg;

/* * generic code calls us with preemption disabled, but some calls @@ -204,25 +197,15 @@ void show_regs(struct pt_regs *regs) STS_BIT(regs, A2), STS_BIT(regs, A1), STS_BIT(regs, E2), STS_BIT(regs, E1)); #else - pr_cont(" [%2s%2s%2s%2s]", + pr_cont(" [%2s%2s%2s%2s] ", STS_BIT(regs, IE), (regs->status32 & STATUS_U_MASK) ? "U " : "K ", STS_BIT(regs, DE), STS_BIT(regs, AE)); #endif - pr_cont(" BTA: 0x%08lx\n SP: 0x%08lx FP: 0x%08lx BLK: %pS\n", - regs->bta, regs->sp, regs->fp, (void *)regs->blink); - pr_info("LPS: 0x%08lx\tLPE: 0x%08lx\tLPC: 0x%08lx\n", - regs->lp_start, regs->lp_end, regs->lp_count); - - /* print regs->r0 thru regs->r12 - * Sequential printing was generating horrible code - */ - print_reg_file(&(regs->r0), 0);

- /* If Callee regs were saved, display them too */ - cregs = (struct callee_regs *)current->thread.callee_reg; + print_regs_scratch(regs); if (cregs) - show_callee_regs(cregs); + print_regs_callee(cregs);

preempt_disable(); }

From: Sean Young sean@mess.org

[ Upstream commit 1451b93223bbe3b4e9c91fca6b451d00667c5bf0 ]

During bit-banging the IR on a gpio pin, we cannot be scheduled or have anything interrupt us, else the generated signal will be incorrect. Therefore, we need to disable interrupts on the local cpu. This also disables preemption.

local_irq_disable() does exactly what we need and does not require a spinlock.

Signed-off-by: Sean Young sean@mess.org Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/rc/gpio-ir-tx.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-)

diff --git a/drivers/media/rc/gpio-ir-tx.c b/drivers/media/rc/gpio-ir-tx.c index f33b443bfa47b..c6cd2e6d8e654 100644 --- a/drivers/media/rc/gpio-ir-tx.c +++ b/drivers/media/rc/gpio-ir-tx.c @@ -19,8 +19,6 @@ struct gpio_ir { struct gpio_desc *gpio; unsigned int carrier; unsigned int duty_cycle; - /* we need a spinlock to hold the cpu while transmitting */ - spinlock_t lock; };

static const struct of_device_id gpio_ir_tx_of_match[] = { @@ -53,12 +51,11 @@ static int gpio_ir_tx_set_carrier(struct rc_dev *dev, u32 carrier) static void gpio_ir_tx_unmodulated(struct gpio_ir *gpio_ir, uint *txbuf, uint count) { - unsigned long flags; ktime_t edge; s32 delta; int i;

- spin_lock_irqsave(&gpio_ir->lock, flags); + local_irq_disable();

edge = ktime_get();

@@ -72,14 +69,11 @@ static void gpio_ir_tx_unmodulated(struct gpio_ir *gpio_ir, uint *txbuf, }

gpiod_set_value(gpio_ir->gpio, 0); - - spin_unlock_irqrestore(&gpio_ir->lock, flags); }

static void gpio_ir_tx_modulated(struct gpio_ir *gpio_ir, uint *txbuf, uint count) { - unsigned long flags; ktime_t edge; /* * delta should never exceed 0.5 seconds (IR_MAX_DURATION) and on @@ -95,7 +89,7 @@ static void gpio_ir_tx_modulated(struct gpio_ir *gpio_ir, uint *txbuf, space = DIV_ROUND_CLOSEST((100 - gpio_ir->duty_cycle) * (NSEC_PER_SEC / 100), gpio_ir->carrier);

- spin_lock_irqsave(&gpio_ir->lock, flags); + local_irq_disable();

edge = ktime_get();

@@ -128,19 +122,20 @@ static void gpio_ir_tx_modulated(struct gpio_ir *gpio_ir, uint *txbuf, edge = last; } } - - spin_unlock_irqrestore(&gpio_ir->lock, flags); }

static int gpio_ir_tx(struct rc_dev *dev, unsigned int *txbuf, unsigned int count) { struct gpio_ir *gpio_ir = dev->priv; + unsigned long flags;

+ local_irq_save(flags); if (gpio_ir->carrier) gpio_ir_tx_modulated(gpio_ir, txbuf, count); else gpio_ir_tx_unmodulated(gpio_ir, txbuf, count); + local_irq_restore(flags);

return count; } @@ -176,7 +171,6 @@ static int gpio_ir_tx_probe(struct platform_device *pdev)

gpio_ir->carrier = 38000; gpio_ir->duty_cycle = 50; - spin_lock_init(&gpio_ir->lock);

rc = devm_rc_register_device(&pdev->dev, rcdev); if (rc < 0)

From: Sagi Grimberg sagi@grimberg.me

[ Upstream commit d7144f5c4cf4de95fdc3422943cf51c06aeaf7a7 ]

NVME_CTRL_NEW should never see any I/O, because in order to start initialization it has to transition to NVME_CTRL_CONNECTING and from there it will never return to this state.

Reviewed-by: Christoph Hellwig hch@lst.de Signed-off-by: Sagi Grimberg sagi@grimberg.me Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/fabrics.c | 1 - 1 file changed, 1 deletion(-)

diff --git a/drivers/nvme/host/fabrics.c b/drivers/nvme/host/fabrics.c index 4ec4829d62334..32f61fc5f4c57 100644 --- a/drivers/nvme/host/fabrics.c +++ b/drivers/nvme/host/fabrics.c @@ -576,7 +576,6 @@ bool __nvmf_check_ready(struct nvme_ctrl *ctrl, struct request *rq, * which is require to set the queue live in the appropinquate states. */ switch (ctrl->state) { - case NVME_CTRL_NEW: case NVME_CTRL_CONNECTING: if (nvme_is_fabrics(req->cmd) && req->cmd->fabrics.fctype == nvme_fabrics_type_connect)

From: Sagi Grimberg sagi@grimberg.me

[ Upstream commit d4d61470ae48838f49e668503e840e1520b97162 ]

In the timeout handler we may need to complete a request because the request that timed out may be an I/O that is a part of a serial sequence of controller teardown or initialization. In order to complete the request, we need to fence any other context that may compete with us and complete the request that is timing out.

In this case, we could have a potential double completion in case a hard-irq or a different competing context triggered error recovery and is running inflight request cancellation concurrently with the timeout handler.

Protect using a ctrl teardown_lock to serialize contexts that may complete a cancelled request due to error recovery or a reset.

Signed-off-by: Sagi Grimberg sagi@grimberg.me Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/tcp.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/nvme/host/tcp.c b/drivers/nvme/host/tcp.c index a6d2e3330a584..d1e5b27675b1b 100644 --- a/drivers/nvme/host/tcp.c +++ b/drivers/nvme/host/tcp.c @@ -122,6 +122,7 @@ struct nvme_tcp_ctrl { struct sockaddr_storage src_addr; struct nvme_ctrl ctrl;

+ struct mutex teardown_lock; struct work_struct err_work; struct delayed_work connect_work; struct nvme_tcp_request async_req; @@ -1497,7 +1498,6 @@ static void nvme_tcp_stop_queue(struct nvme_ctrl *nctrl, int qid)

if (!test_and_clear_bit(NVME_TCP_Q_LIVE, &queue->flags)) return; - __nvme_tcp_stop_queue(queue); }

@@ -1845,6 +1845,7 @@ static int nvme_tcp_configure_admin_queue(struct nvme_ctrl *ctrl, bool new) static void nvme_tcp_teardown_admin_queue(struct nvme_ctrl *ctrl, bool remove) { + mutex_lock(&to_tcp_ctrl(ctrl)->teardown_lock); blk_mq_quiesce_queue(ctrl->admin_q); nvme_tcp_stop_queue(ctrl, 0); if (ctrl->admin_tagset) { @@ -1855,13 +1856,16 @@ static void nvme_tcp_teardown_admin_queue(struct nvme_ctrl *ctrl, if (remove) blk_mq_unquiesce_queue(ctrl->admin_q); nvme_tcp_destroy_admin_queue(ctrl, remove); + mutex_unlock(&to_tcp_ctrl(ctrl)->teardown_lock); }

static void nvme_tcp_teardown_io_queues(struct nvme_ctrl *ctrl, bool remove) { + mutex_lock(&to_tcp_ctrl(ctrl)->teardown_lock); if (ctrl->queue_count <= 1) - return; + goto out; + blk_mq_quiesce_queue(ctrl->admin_q); nvme_start_freeze(ctrl); nvme_stop_queues(ctrl); nvme_tcp_stop_io_queues(ctrl); @@ -1873,6 +1877,8 @@ static void nvme_tcp_teardown_io_queues(struct nvme_ctrl *ctrl, if (remove) nvme_start_queues(ctrl); nvme_tcp_destroy_io_queues(ctrl, remove); +out: + mutex_unlock(&to_tcp_ctrl(ctrl)->teardown_lock); }

static void nvme_tcp_reconnect_or_remove(struct nvme_ctrl *ctrl) @@ -2384,6 +2390,7 @@ static struct nvme_ctrl *nvme_tcp_create_ctrl(struct device *dev, nvme_tcp_reconnect_ctrl_work); INIT_WORK(&ctrl->err_work, nvme_tcp_error_recovery_work); INIT_WORK(&ctrl->ctrl.reset_work, nvme_reset_ctrl_work); + mutex_init(&ctrl->teardown_lock);

if (!(opts->mask & NVMF_OPT_TRSVCID)) { opts->trsvcid =

From: Sagi Grimberg sagi@grimberg.me

[ Upstream commit e5c01f4f7f623e768e868bcc08d8e7ceb03b75d0 ]

If the controller becomes unresponsive in the middle of a reset, we will hang because we are waiting for the freeze to complete, but that cannot happen since we have commands that are inflight holding the q_usage_counter, and we can't blindly fail requests that times out.

So give a timeout and if we cannot wait for queue freeze before unfreezing, fail and have the error handling take care how to proceed (either schedule a reconnect of remove the controller).

Signed-off-by: Sagi Grimberg sagi@grimberg.me Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/tcp.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/nvme/host/tcp.c b/drivers/nvme/host/tcp.c index 65a3bad778104..f1f66bf96cbb9 100644 --- a/drivers/nvme/host/tcp.c +++ b/drivers/nvme/host/tcp.c @@ -1753,7 +1753,15 @@ static int nvme_tcp_configure_io_queues(struct nvme_ctrl *ctrl, bool new)

if (!new) { nvme_start_queues(ctrl); - nvme_wait_freeze(ctrl); + if (!nvme_wait_freeze_timeout(ctrl, NVME_IO_TIMEOUT)) { + /* + * If we timed out waiting for freeze we are likely to + * be stuck. Fail the controller initialization just + * to be safe. + */ + ret = -ENODEV; + goto out_wait_freeze_timed_out; + } blk_mq_update_nr_hw_queues(ctrl->tagset, ctrl->queue_count - 1); nvme_unfreeze(ctrl); @@ -1761,6 +1769,9 @@ static int nvme_tcp_configure_io_queues(struct nvme_ctrl *ctrl, bool new)

return 0;

+out_wait_freeze_timed_out: + nvme_stop_queues(ctrl); + nvme_tcp_stop_io_queues(ctrl); out_cleanup_connect_q: if (new) blk_cleanup_queue(ctrl->connect_q);

From: Sagi Grimberg sagi@grimberg.me

[ Upstream commit 0475a8dcbcee92a5d22e40c9c6353829fc6294b8 ]

When a request times out in a LIVE state, we simply trigger error recovery and let the error recovery handle the request cancellation, however when a request times out in a non LIVE state, we make sure to complete it immediately as it might block controller setup or teardown and prevent forward progress.

However tearing down the entire set of I/O and admin queues causes freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really an overkill to what we actually need, which is to just fence controller teardown that may be running, stop the queue, and cancel the request if it is not already completed.

Now that we have the controller teardown_lock, we can safely serialize request cancellation. This addresses a hang caused by calling extra queue freeze on controller namespaces, causing unfreeze to not complete correctly.

Reviewed-by: Christoph Hellwig hch@lst.de Reviewed-by: James Smart james.smart@broadcom.com Signed-off-by: Sagi Grimberg sagi@grimberg.me Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/rdma.c | 49 +++++++++++++++++++++++++++------------- 1 file changed, 33 insertions(+), 16 deletions(-)

diff --git a/drivers/nvme/host/rdma.c b/drivers/nvme/host/rdma.c index ffe83d1f576bf..99bf88eb812c5 100644 --- a/drivers/nvme/host/rdma.c +++ b/drivers/nvme/host/rdma.c @@ -1159,6 +1159,7 @@ static void nvme_rdma_error_recovery(struct nvme_rdma_ctrl *ctrl) if (!nvme_change_ctrl_state(&ctrl->ctrl, NVME_CTRL_RESETTING)) return;

+ dev_warn(ctrl->ctrl.device, "starting error recovery\n"); queue_work(nvme_reset_wq, &ctrl->err_work); }

@@ -1925,6 +1926,22 @@ static int nvme_rdma_cm_handler(struct rdma_cm_id *cm_id, return 0; }

+static void nvme_rdma_complete_timed_out(struct request *rq) +{ + struct nvme_rdma_request *req = blk_mq_rq_to_pdu(rq); + struct nvme_rdma_queue *queue = req->queue; + struct nvme_rdma_ctrl *ctrl = queue->ctrl; + + /* fence other contexts that may complete the command */ + mutex_lock(&ctrl->teardown_lock); + nvme_rdma_stop_queue(queue); + if (!blk_mq_request_completed(rq)) { + nvme_req(rq)->status = NVME_SC_HOST_ABORTED_CMD; + blk_mq_complete_request(rq); + } + mutex_unlock(&ctrl->teardown_lock); +} + static enum blk_eh_timer_return nvme_rdma_timeout(struct request *rq, bool reserved) { @@ -1935,29 +1952,29 @@ nvme_rdma_timeout(struct request *rq, bool reserved) dev_warn(ctrl->ctrl.device, "I/O %d QID %d timeout\n", rq->tag, nvme_rdma_queue_idx(queue));

- /* - * Restart the timer if a controller reset is already scheduled. Any - * timed out commands would be handled before entering the connecting - * state. - */ - if (ctrl->ctrl.state == NVME_CTRL_RESETTING) - return BLK_EH_RESET_TIMER; - if (ctrl->ctrl.state != NVME_CTRL_LIVE) { /* - * Teardown immediately if controller times out while starting - * or we are already started error recovery. all outstanding - * requests are completed on shutdown, so we return BLK_EH_DONE. + * If we are resetting, connecting or deleting we should + * complete immediately because we may block controller + * teardown or setup sequence + * - ctrl disable/shutdown fabrics requests + * - connect requests + * - initialization admin requests + * - I/O requests that entered after unquiescing and + * the controller stopped responding + * + * All other requests should be cancelled by the error + * recovery work, so it's fine that we fail it here. */ - flush_work(&ctrl->err_work); - nvme_rdma_teardown_io_queues(ctrl, false); - nvme_rdma_teardown_admin_queue(ctrl, false); + nvme_rdma_complete_timed_out(rq); return BLK_EH_DONE; }

- dev_warn(ctrl->ctrl.device, "starting error recovery\n"); + /* + * LIVE state should trigger the normal error recovery which will + * handle completing this request. + */ nvme_rdma_error_recovery(ctrl); - return BLK_EH_RESET_TIMER; }

From: Tong Zhang ztong0001@gmail.com

[ Upstream commit 7ad92f656bddff4cf8f641e0e3b1acd4eb9644cb ]

This patch addresses an irq free warning and null pointer dereference error problem when nvme devices got timeout error during initialization. This problem happens when nvme_timeout() function is called while nvme_reset_work() is still in execution. This patch fixed the problem by setting flag of the problematic request to NVME_REQ_CANCELLED before calling nvme_dev_disable() to make sure __nvme_submit_sync_cmd() returns an error code and let nvme_submit_sync_cmd() fail gracefully. The following is console output.

[ 62.472097] nvme nvme0: I/O 13 QID 0 timeout, disable controller [ 62.488796] nvme nvme0: could not set timestamp (881) [ 62.494888] ------------[ cut here ]------------ [ 62.495142] Trying to free already-free IRQ 11 [ 62.495366] WARNING: CPU: 0 PID: 7 at kernel/irq/manage.c:1751 free_irq+0x1f7/0x370 [ 62.495742] Modules linked in: [ 62.495902] CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.8.0+ #8 [ 62.496206] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-48-gd9c812dda519-p4 [ 62.496772] Workqueue: nvme-reset-wq nvme_reset_work [ 62.497019] RIP: 0010:free_irq+0x1f7/0x370 [ 62.497223] Code: e8 ce 49 11 00 48 83 c4 08 4c 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 44 89 f6 48 c70 [ 62.498133] RSP: 0000:ffffa96800043d40 EFLAGS: 00010086 [ 62.498391] RAX: 0000000000000000 RBX: ffff9b87fc458400 RCX: 0000000000000000 [ 62.498741] RDX: 0000000000000001 RSI: 0000000000000096 RDI: ffffffff9693d72c [ 62.499091] RBP: ffff9b87fd4c8f60 R08: ffffa96800043bfd R09: 0000000000000163 [ 62.499440] R10: ffffa96800043bf8 R11: ffffa96800043bfd R12: ffff9b87fd4c8e00 [ 62.499790] R13: ffff9b87fd4c8ea4 R14: 000000000000000b R15: ffff9b87fd76b000 [ 62.500140] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 62.500534] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 62.500816] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 62.501165] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 62.501515] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 62.501864] Call Trace: [ 62.501993] pci_free_irq+0x13/0x20 [ 62.502167] nvme_reset_work+0x5d0/0x12a0 [ 62.502369] ? update_load_avg+0x59/0x580 [ 62.502569] ? ttwu_queue_wakelist+0xa8/0xc0 [ 62.502780] ? try_to_wake_up+0x1a2/0x450 [ 62.502979] process_one_work+0x1d2/0x390 [ 62.503179] worker_thread+0x45/0x3b0 [ 62.503361] ? process_one_work+0x390/0x390 [ 62.503568] kthread+0xf9/0x130 [ 62.503726] ? kthread_park+0x80/0x80 [ 62.503911] ret_from_fork+0x22/0x30 [ 62.504090] ---[ end trace de9ed4a70f8d71e2 ]--- [ 123.912275] nvme nvme0: I/O 12 QID 0 timeout, disable controller [ 123.914670] nvme nvme0: 1/0/0 default/read/poll queues [ 123.916310] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 123.917469] #PF: supervisor write access in kernel mode [ 123.917725] #PF: error_code(0x0002) - not-present page [ 123.917976] PGD 0 P4D 0 [ 123.918109] Oops: 0002 [#1] SMP PTI [ 123.918283] CPU: 0 PID: 7 Comm: kworker/u4:0 Tainted: G W 5.8.0+ #8 [ 123.918650] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-48-gd9c812dda519-p4 [ 123.919219] Workqueue: nvme-reset-wq nvme_reset_work [ 123.919469] RIP: 0010:__blk_mq_alloc_map_and_request+0x21/0x80 [ 123.919757] Code: 66 0f 1f 84 00 00 00 00 00 41 55 41 54 55 48 63 ee 53 48 8b 47 68 89 ee 48 89 fb 8b4 [ 123.920657] RSP: 0000:ffffa96800043d40 EFLAGS: 00010286 [ 123.920912] RAX: ffff9b87fc4fee40 RBX: ffff9b87fc8cb008 RCX: 0000000000000000 [ 123.921258] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9b87fc618000 [ 123.921602] RBP: 0000000000000000 R08: ffff9b87fdc2c4a0 R09: ffff9b87fc616000 [ 123.921949] R10: 0000000000000000 R11: ffff9b87fffd1500 R12: 0000000000000000 [ 123.922295] R13: 0000000000000000 R14: ffff9b87fc8cb200 R15: ffff9b87fc8cb000 [ 123.922641] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 123.923032] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 123.923312] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 123.923660] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 123.924007] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 123.924353] Call Trace: [ 123.924479] blk_mq_alloc_tag_set+0x137/0x2a0 [ 123.924694] nvme_reset_work+0xed6/0x12a0 [ 123.924898] process_one_work+0x1d2/0x390 [ 123.925099] worker_thread+0x45/0x3b0 [ 123.925280] ? process_one_work+0x390/0x390 [ 123.925486] kthread+0xf9/0x130 [ 123.925642] ? kthread_park+0x80/0x80 [ 123.925825] ret_from_fork+0x22/0x30 [ 123.926004] Modules linked in: [ 123.926158] CR2: 0000000000000000 [ 123.926322] ---[ end trace de9ed4a70f8d71e3 ]--- [ 123.926549] RIP: 0010:__blk_mq_alloc_map_and_request+0x21/0x80 [ 123.926832] Code: 66 0f 1f 84 00 00 00 00 00 41 55 41 54 55 48 63 ee 53 48 8b 47 68 89 ee 48 89 fb 8b4 [ 123.927734] RSP: 0000:ffffa96800043d40 EFLAGS: 00010286 [ 123.927989] RAX: ffff9b87fc4fee40 RBX: ffff9b87fc8cb008 RCX: 0000000000000000 [ 123.928336] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9b87fc618000 [ 123.928679] RBP: 0000000000000000 R08: ffff9b87fdc2c4a0 R09: ffff9b87fc616000 [ 123.929025] R10: 0000000000000000 R11: ffff9b87fffd1500 R12: 0000000000000000 [ 123.929370] R13: 0000000000000000 R14: ffff9b87fc8cb200 R15: ffff9b87fc8cb000 [ 123.929715] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 123.930106] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 123.930384] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 123.930731] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 123.931077] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Co-developed-by: Keith Busch kbusch@kernel.org Signed-off-by: Tong Zhang ztong0001@gmail.com Reviewed-by: Keith Busch kbusch@kernel.org Signed-off-by: Sagi Grimberg sagi@grimberg.me Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/nvme/host/pci.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/nvme/host/pci.c b/drivers/nvme/host/pci.c index d4b1ff7471231..69a19fe241063 100644 --- a/drivers/nvme/host/pci.c +++ b/drivers/nvme/host/pci.c @@ -1250,8 +1250,8 @@ static enum blk_eh_timer_return nvme_timeout(struct request *req, bool reserved) dev_warn_ratelimited(dev->ctrl.device, "I/O %d QID %d timeout, disable controller\n", req->tag, nvmeq->qid); - nvme_dev_disable(dev, true); nvme_req(req)->flags |= NVME_REQ_CANCELLED; + nvme_dev_disable(dev, true); return BLK_EH_DONE; case NVME_CTRL_RESETTING: return BLK_EH_RESET_TIMER; @@ -1268,10 +1268,10 @@ static enum blk_eh_timer_return nvme_timeout(struct request *req, bool reserved) dev_warn(dev->ctrl.device, "I/O %d QID %d timeout, reset controller\n", req->tag, nvmeq->qid); + nvme_req(req)->flags |= NVME_REQ_CANCELLED; nvme_dev_disable(dev, false); nvme_reset_ctrl(&dev->ctrl);

- nvme_req(req)->flags |= NVME_REQ_CANCELLED; return BLK_EH_DONE; }

From: Nicholas Miell nmiell@gmail.com

[ Upstream commit 724a419ea28f7514a391e80040230f69cf626707 ]

When operating in XInput mode, the 8bitdo SN30 Pro+ requires the same quirk as the official Xbox One Bluetooth controllers for rumble to function.

Other controllers like the N30 Pro 2, SF30 Pro, SN30 Pro, etc. probably also need this quirk, but I do not have the hardware to test.

Signed-off-by: Nicholas Miell nmiell@gmail.com Signed-off-by: Jiri Kosina jkosina@suse.cz Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/hid/hid-ids.h | 1 + drivers/hid/hid-microsoft.c | 2 ++ 2 files changed, 3 insertions(+)

diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index 476cb99bd61b7..95f9d285b3c6b 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -846,6 +846,7 @@ #define USB_DEVICE_ID_MS_POWER_COVER 0x07da #define USB_DEVICE_ID_MS_XBOX_ONE_S_CONTROLLER 0x02fd #define USB_DEVICE_ID_MS_PIXART_MOUSE 0x00cb +#define USB_DEVICE_ID_8BITDO_SN30_PRO_PLUS 0x02e0

#define USB_VENDOR_ID_MOJO 0x8282 #define USB_DEVICE_ID_RETRO_ADAPTER 0x3201 diff --git a/drivers/hid/hid-microsoft.c b/drivers/hid/hid-microsoft.c index 2d8b589201a4e..8cb1ca1936e42 100644 --- a/drivers/hid/hid-microsoft.c +++ b/drivers/hid/hid-microsoft.c @@ -451,6 +451,8 @@ static const struct hid_device_id ms_devices[] = { .driver_data = MS_SURFACE_DIAL }, { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_XBOX_ONE_S_CONTROLLER), .driver_data = MS_QUIRK_FF }, + { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_8BITDO_SN30_PRO_PLUS), + .driver_data = MS_QUIRK_FF }, { } }; MODULE_DEVICE_TABLE(hid, ms_devices);

From: Dinghao Liu dinghao.liu@zju.edu.cn

[ Upstream commit b7429ea53d6c0936a0f10a5d64164f0aea440143 ]

When input_mt_init_slots() fails, input should be freed to prevent memleak. When input_register_device() fails, we should call input_mt_destroy_slots() to free memory allocated by input_mt_init_slots().

Signed-off-by: Dinghao Liu dinghao.liu@zju.edu.cn Signed-off-by: Jiri Kosina jkosina@suse.cz Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/hid/hid-elan.c | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/drivers/hid/hid-elan.c b/drivers/hid/hid-elan.c index 45c4f888b7c4e..dae193749d443 100644 --- a/drivers/hid/hid-elan.c +++ b/drivers/hid/hid-elan.c @@ -188,6 +188,7 @@ static int elan_input_configured(struct hid_device *hdev, struct hid_input *hi) ret = input_mt_init_slots(input, ELAN_MAX_FINGERS, INPUT_MT_POINTER); if (ret) { hid_err(hdev, "Failed to init elan MT slots: %d\n", ret); + input_free_device(input); return ret; }

@@ -198,6 +199,7 @@ static int elan_input_configured(struct hid_device *hdev, struct hid_input *hi) if (ret) { hid_err(hdev, "Failed to register elan input device: %d\n", ret); + input_mt_destroy_slots(input); input_free_device(input); return ret; }

From: "Rafael J. Wysocki" rafael.j.wysocki@intel.com

[ Upstream commit 43298db3009f06fe5c69e1ca8b6cfc2565772fa1 ]

After commit f6ebbcf08f37 ("cpufreq: intel_pstate: Implement passive mode with HWP enabled") it is possible to change the driver status to "off" via sysfs with HWP enabled, which effectively causes the driver to unregister itself, but HWP remains active and it forces the minimum performance, so even if another cpufreq driver is loaded, it will not be able to control the CPU frequency.

For this reason, make the driver refuse to change the status to "off" with HWP enabled.

Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Acked-by: Srinivas Pandruvada srinivas.pandruvada@linux.intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/cpufreq/intel_pstate.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/cpufreq/intel_pstate.c b/drivers/cpufreq/intel_pstate.c index 8c730a47e0537..97ed4fd0f1342 100644 --- a/drivers/cpufreq/intel_pstate.c +++ b/drivers/cpufreq/intel_pstate.c @@ -2534,9 +2534,15 @@ static int intel_pstate_update_status(const char *buf, size_t size) { int ret;

- if (size == 3 && !strncmp(buf, "off", size)) - return intel_pstate_driver ? - intel_pstate_unregister_driver() : -EINVAL; + if (size == 3 && !strncmp(buf, "off", size)) { + if (!intel_pstate_driver) + return -EINVAL; + + if (hwp_active) + return -EBUSY; + + return intel_pstate_unregister_driver(); + }

if (size == 6 && !strncmp(buf, "active", size)) { if (intel_pstate_driver) {

From: Kamil Lorenc kamil@re-ws.pl

[ Upstream commit a609d0259183a841621f252e067f40f8cc25d6f6 ]

Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface.

Signed-off-by: Kamil Lorenc kamil@re-ws.pl Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/usb/dm9601.c | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/drivers/net/usb/dm9601.c b/drivers/net/usb/dm9601.c index b91f92e4e5f22..915ac75b55fc7 100644 --- a/drivers/net/usb/dm9601.c +++ b/drivers/net/usb/dm9601.c @@ -625,6 +625,10 @@ static const struct usb_device_id products[] = { USB_DEVICE(0x0a46, 0x1269), /* DM9621A USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, + { + USB_DEVICE(0x0586, 0x3427), /* ZyXEL Keenetic Plus DSL xDSL modem */ + .driver_info = (unsigned long)&dm9601_info, + }, {}, // END };

From: Rander Wang rander.wang@intel.com

[ Upstream commit f804a324a41a880c1ab43cc5145d8b3e5790430d ]

Add Rocketlake HDMI codec support. Rocketlake shares the pin-to-port mapping table with Tigerlake.

Signed-off-by: Rander Wang rander.wang@intel.com Reviewed-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com Reviewed-by: Ranjani Sridharan ranjani.sridharan@linux.intel.com Signed-off-by: Kai Vehmanen kai.vehmanen@linux.intel.com Link: https://lore.kernel.org/r/20200902154207.1440393-1-kai.vehmanen@linux.intel.... Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Sasha Levin sashal@kernel.org --- sound/pci/hda/patch_hdmi.c | 1 + 1 file changed, 1 insertion(+)

diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 9442127d9b15d..43ae35338a383 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4204,6 +4204,7 @@ HDA_CODEC_ENTRY(0x8086280c, "Cannonlake HDMI", patch_i915_glk_hdmi), HDA_CODEC_ENTRY(0x8086280d, "Geminilake HDMI", patch_i915_glk_hdmi), HDA_CODEC_ENTRY(0x8086280f, "Icelake HDMI", patch_i915_icl_hdmi), HDA_CODEC_ENTRY(0x80862812, "Tigerlake HDMI", patch_i915_tgl_hdmi), +HDA_CODEC_ENTRY(0x80862816, "Rocketlake HDMI", patch_i915_tgl_hdmi), HDA_CODEC_ENTRY(0x8086281a, "Jasperlake HDMI", patch_i915_icl_hdmi), HDA_CODEC_ENTRY(0x8086281b, "Elkhartlake HDMI", patch_i915_icl_hdmi), HDA_CODEC_ENTRY(0x80862880, "CedarTrail HDMI", patch_generic_hdmi),

From: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com

[ Upstream commit b79de57b4378a93115307be6962d05b099eb0f37 ]

We use HDaudio and HDAudio, pick one to make searches easier. No functionality change

Also fix timestamping typo in documentation.

Reported-by: Guennadi Liakhovetski guennadi.liakhovetski@linux.intel.com Signed-off-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao yung-chuan.liao@linux.intel.com Reviewed-by: Guennadi Liakhovetski guennadi.liakhovetski@linux.intel.com Signed-off-by: Kai Vehmanen kai.vehmanen@linux.intel.com Link: https://lore.kernel.org/r/20200902154250.1440585-1-kai.vehmanen@linux.intel.... Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Sasha Levin sashal@kernel.org --- Documentation/sound/designs/timestamping.rst | 2 +- sound/hda/intel-dsp-config.c | 10 +++++----- sound/x86/Kconfig | 2 +- 3 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/Documentation/sound/designs/timestamping.rst b/Documentation/sound/designs/timestamping.rst index 2b0fff5034151..7c7ecf5dbc4bd 100644 --- a/Documentation/sound/designs/timestamping.rst +++ b/Documentation/sound/designs/timestamping.rst @@ -143,7 +143,7 @@ timestamp shows when the information is put together by the driver before returning from the ``STATUS`` and ``STATUS_EXT`` ioctl. in most cases this driver_timestamp will be identical to the regular system tstamp.

-Examples of typestamping with HDaudio: +Examples of timestamping with HDAudio:

1. DMA timestamp, no compensation for DMA+analog delay :: diff --git a/sound/hda/intel-dsp-config.c b/sound/hda/intel-dsp-config.c index 99aec73491676..1c5114dedda92 100644 --- a/sound/hda/intel-dsp-config.c +++ b/sound/hda/intel-dsp-config.c @@ -54,7 +54,7 @@ static const struct config_entry config_table[] = { #endif /* * Apollolake (Broxton-P) - * the legacy HDaudio driver is used except on Up Squared (SOF) and + * the legacy HDAudio driver is used except on Up Squared (SOF) and * Chromebooks (SST) */ #if IS_ENABLED(CONFIG_SND_SOC_SOF_APOLLOLAKE) @@ -89,7 +89,7 @@ static const struct config_entry config_table[] = { }, #endif /* - * Skylake and Kabylake use legacy HDaudio driver except for Google + * Skylake and Kabylake use legacy HDAudio driver except for Google * Chromebooks (SST) */

@@ -135,7 +135,7 @@ static const struct config_entry config_table[] = { #endif

/* - * Geminilake uses legacy HDaudio driver except for Google + * Geminilake uses legacy HDAudio driver except for Google * Chromebooks */ /* Geminilake */ @@ -157,7 +157,7 @@ static const struct config_entry config_table[] = {

/* * CoffeeLake, CannonLake, CometLake, IceLake, TigerLake use legacy - * HDaudio driver except for Google Chromebooks and when DMICs are + * HDAudio driver except for Google Chromebooks and when DMICs are * present. Two cases are required since Coreboot does not expose NHLT * tables. * @@ -391,7 +391,7 @@ int snd_intel_dsp_driver_probe(struct pci_dev *pci) if (pci->class == 0x040300) return SND_INTEL_DSP_DRIVER_LEGACY; if (pci->class != 0x040100 && pci->class != 0x040380) { - dev_err(&pci->dev, "Unknown PCI class/subclass/prog-if information (0x%06x) found, selecting HDA legacy driver\n", pci->class); + dev_err(&pci->dev, "Unknown PCI class/subclass/prog-if information (0x%06x) found, selecting HDAudio legacy driver\n", pci->class); return SND_INTEL_DSP_DRIVER_LEGACY; }

diff --git a/sound/x86/Kconfig b/sound/x86/Kconfig index 77777192f6508..4ffcc5e623c22 100644 --- a/sound/x86/Kconfig +++ b/sound/x86/Kconfig @@ -9,7 +9,7 @@ menuconfig SND_X86 if SND_X86

config HDMI_LPE_AUDIO - tristate "HDMI audio without HDaudio on Intel Atom platforms" + tristate "HDMI audio without HDAudio on Intel Atom platforms" depends on DRM_I915 select SND_PCM help

From: Sandeep Raghuraman sandy.8925@gmail.com

[ Upstream commit d98299885c9ea140c1108545186593deba36c4ac ]

On my R9 390, the voltage was reported as a constant 1000 mV. This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor() function, where some magic constants were used in a condition, to determine whether the voltage should be read from PLANE2_VID or PLANE1_VID. The VDDC mask was incorrectly used, instead of the VDDGFX mask.

This patch changes the code to use the correct defined constants (and apply the correct bitshift), thus resulting in correct voltage reporting.

Signed-off-by: Sandeep Raghuraman sandy.8925@gmail.com Signed-off-by: Alex Deucher alexander.deucher@amd.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c index 753cb2cf6b77e..3adf9c1dfdbb0 100644 --- a/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c +++ b/drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c @@ -3587,7 +3587,8 @@ static int smu7_read_sensor(struct pp_hwmgr *hwmgr, int idx, case AMDGPU_PP_SENSOR_GPU_POWER: return smu7_get_gpu_power(hwmgr, (uint32_t *)value); case AMDGPU_PP_SENSOR_VDDGFX: - if ((data->vr_config & 0xff) == 0x2) + if ((data->vr_config & VRCONF_VDDGFX_MASK) == + (VR_SVI2_PLANE_2 << VRCONF_VDDGFX_SHIFT)) val_vid = PHM_READ_INDIRECT_FIELD(hwmgr->device, CGS_IND_REG__SMC, PWR_SVI2_STATUS, PLANE2_VID); else

From: Joerg Roedel jroedel@suse.de

[ Upstream commit 2822e582501b65707089b097e773e6fd70774841 ]

When memory encryption is active the device is likely not in a direct mapped domain. Forbid using IOMMUv2 functionality for now until finer grained checks for this have been implemented.

Signed-off-by: Joerg Roedel jroedel@suse.de Link: https://lore.kernel.org/r/20200824105415.21000-3-joro@8bytes.org Signed-off-by: Joerg Roedel jroedel@suse.de Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/iommu/amd/iommu_v2.c | 7 +++++++ 1 file changed, 7 insertions(+)

diff --git a/drivers/iommu/amd/iommu_v2.c b/drivers/iommu/amd/iommu_v2.c index e4b025c5637c4..5a188cac7a0f1 100644 --- a/drivers/iommu/amd/iommu_v2.c +++ b/drivers/iommu/amd/iommu_v2.c @@ -737,6 +737,13 @@ int amd_iommu_init_device(struct pci_dev *pdev, int pasids)

might_sleep();

+ /* + * When memory encryption is active the device is likely not in a + * direct-mapped domain. Forbid using IOMMUv2 functionality for now. + */ + if (mem_encrypt_active()) + return -ENODEV; + if (!amd_iommu_v2_supported()) return -ENODEV;