This is a note to let you know that I've just added the patch titled
serial: 8250_mtk: Fix UART_EFR register address
to my tty git tree which can be found at git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git in the tty-linus branch.
The patch will show up in the next release of the linux-next tree (usually sometime within the next 24 hours during the week.)
The patch will hopefully also be merged in Linus's tree for the next -rc kernel release.
If you have any questions about this process, please let me know.
From bb0b197aadd928f52ce6f01f0ee977f0a08cf1be Mon Sep 17 00:00:00 2001 From: AngeloGioacchino Del Regno angelogioacchino.delregno@collabora.com Date: Wed, 27 Apr 2022 15:23:26 +0200 Subject: serial: 8250_mtk: Fix UART_EFR register address
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some specific quirks: we are declaring a register shift of 2, but this is only valid for the majority of the registers, as there are some that are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where we have a UART_EFR register defined as 2: this results in a 0x8 offset, but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98, so, following the decimal definition convention in serial_reg.h and accounting for the register left shift of two, add and use the correct register address for this IP, defined as decimal 38, so that the final calculation results in (0x26 << 2) = 0x98.
Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting") Signed-off-by: AngeloGioacchino Del Regno angelogioacchino.delregno@collabora.com Cc: stable stable@vger.kernel.org Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/tty/serial/8250/8250_mtk.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index f4a0caa56f84..cd62a5f34014 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -37,6 +37,7 @@ #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */
+#define MTK_UART_EFR 38 /* I/O: Extended Features Register */ #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ @@ -169,7 +170,7 @@ static void mtk8250_dma_enable(struct uart_8250_port *up) MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr);
if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0) @@ -232,7 +233,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) int lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr); lcr = serial_in(up, UART_LCR);
@@ -241,7 +242,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); serial_out(up, MTK_UART_ESCAPE_EN, 0x00); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); serial_out(up, UART_LCR, lcr); mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | @@ -255,8 +256,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable hw flow control*/ - serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
serial_out(up, UART_LCR, lcr); @@ -270,8 +271,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable sw flow control */ - serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
serial_out(up, UART_XON1, START_CHAR(port->state->port.tty));
linux-stable-mirror@lists.linaro.org