From: Mathias Nyman mathias.nyman@linux.intel.com

commit e1959faf085b004e6c3afaaaa743381f00e7c015 upstream.

Some USB 3.1 enumeration issues were reported after the hub driver removed the minimum 100ms limit for the power-on-good delay.

Since commit 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub") the hub driver sets the power-on-delay based on the bPwrOn2PwrGood value in the hub descriptor.

xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based on xhci spec section 5.4.8, but it's clearly not enough for the USB 3.1 devices, causing enumeration issues.

Tests indicate full 100ms delay is needed.

Reported-by: Walt Jr. Brake mr.yming81@gmail.com Signed-off-by: Mathias Nyman mathias.nyman@linux.intel.com Fixes: 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub") Cc: stable stable@vger.kernel.org Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/usb/host/xhci-hub.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/usb/host/xhci-hub.c +++ b/drivers/usb/host/xhci-hub.c @@ -171,7 +171,6 @@ static void xhci_common_hub_descriptor(s { u16 temp;

- desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.9 says 20ms max */ desc->bHubContrCurrent = 0;

desc->bNbrPorts = ports; @@ -206,6 +205,7 @@ static void xhci_usb2_hub_descriptor(str desc->bDescriptorType = USB_DT_HUB; temp = 1 + (ports / 8); desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp; + desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.8 says 20ms */

/* The Device Removable bits are reported on a byte granularity. * If the port doesn't exist within that byte, the bit is set to 0. @@ -258,6 +258,7 @@ static void xhci_usb3_hub_descriptor(str xhci_common_hub_descriptor(xhci, desc, ports); desc->bDescriptorType = USB_DT_SS_HUB; desc->bDescLength = USB_DT_SS_HUB_SIZE; + desc->bPwrOn2PwrGood = 50; /* usb 3.1 may fail if less than 100ms */

/* header decode latency should be zero for roothubs, * see section 4.23.5.2.

From: Todd Kjos tkjos@google.com

commit 52f88693378a58094c538662ba652aff0253c4fe upstream.

Since binder was integrated with selinux, it has passed 'struct task_struct' associated with the binder_proc to represent the source and target of transactions. The conversion of task to SID was then done in the hook implementations. It turns out that there are race conditions which can result in an incorrect security context being used.

Fix by using the 'struct cred' saved during binder_open and pass it to the selinux subsystem.

Cc: stable@vger.kernel.org # 5.14 (need backport for earlier stables) Fixes: 79af73079d75 ("Add security hooks to binder and implement the hooks for SELinux.") Suggested-by: Jann Horn jannh@google.com Signed-off-by: Todd Kjos tkjos@google.com Acked-by: Casey Schaufler casey@schaufler-ca.com Signed-off-by: Paul Moore paul@paul-moore.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org

--- drivers/android/binder.c | 12 ++++++------ include/linux/lsm_hooks.h | 28 ++++++++++++++-------------- include/linux/security.h | 28 ++++++++++++++-------------- security/security.c | 14 +++++++------- security/selinux/hooks.c | 36 +++++++++++++++--------------------- 5 files changed, 56 insertions(+), 62 deletions(-)

--- a/drivers/android/binder.c +++ b/drivers/android/binder.c @@ -2337,7 +2337,7 @@ static int binder_translate_binder(struc ret = -EINVAL; goto done; } - if (security_binder_transfer_binder(proc->tsk, target_proc->tsk)) { + if (security_binder_transfer_binder(proc->cred, target_proc->cred)) { ret = -EPERM; goto done; } @@ -2383,7 +2383,7 @@ static int binder_translate_handle(struc proc->pid, thread->pid, fp->handle); return -EINVAL; } - if (security_binder_transfer_binder(proc->tsk, target_proc->tsk)) { + if (security_binder_transfer_binder(proc->cred, target_proc->cred)) { ret = -EPERM; goto done; } @@ -2467,7 +2467,7 @@ static int binder_translate_fd(int fd, ret = -EBADF; goto err_fget; } - ret = security_binder_transfer_file(proc->tsk, target_proc->tsk, file); + ret = security_binder_transfer_file(proc->cred, target_proc->cred, file); if (ret < 0) { ret = -EPERM; goto err_security; @@ -2851,8 +2851,8 @@ static void binder_transaction(struct bi return_error_line = __LINE__; goto err_invalid_target_handle; } - if (security_binder_transaction(proc->tsk, - target_proc->tsk) < 0) { + if (security_binder_transaction(proc->cred, + target_proc->cred) < 0) { return_error = BR_FAILED_REPLY; return_error_param = -EPERM; return_error_line = __LINE__; @@ -4549,7 +4549,7 @@ static int binder_ioctl_set_ctx_mgr(stru ret = -EBUSY; goto out; } - ret = security_binder_set_context_mgr(proc->tsk); + ret = security_binder_set_context_mgr(proc->cred); if (ret < 0) goto out; if (uid_valid(context->binder_context_mgr_uid)) { --- a/include/linux/lsm_hooks.h +++ b/include/linux/lsm_hooks.h @@ -1211,22 +1211,22 @@ * * @binder_set_context_mgr: * Check whether @mgr is allowed to be the binder context manager. - * @mgr contains the task_struct for the task being registered. + * @mgr contains the struct cred for the current binder process. * Return 0 if permission is granted. * @binder_transaction: * Check whether @from is allowed to invoke a binder transaction call * to @to. - * @from contains the task_struct for the sending task. - * @to contains the task_struct for the receiving task. + * @from contains the struct cred for the sending process. + * @to contains the struct cred for the receiving process. * @binder_transfer_binder: * Check whether @from is allowed to transfer a binder reference to @to. - * @from contains the task_struct for the sending task. - * @to contains the task_struct for the receiving task. + * @from contains the struct cred for the sending process. + * @to contains the struct cred for the receiving process. * @binder_transfer_file: * Check whether @from is allowed to transfer @file to @to. - * @from contains the task_struct for the sending task. + * @from contains the struct cred for the sending process. * @file contains the struct file being transferred. - * @to contains the task_struct for the receiving task. + * @to contains the struct cred for the receiving process. * * @ptrace_access_check: * Check permission before allowing the current process to trace the @@ -1428,13 +1428,13 @@ * */ union security_list_options { - int (*binder_set_context_mgr)(struct task_struct *mgr); - int (*binder_transaction)(struct task_struct *from, - struct task_struct *to); - int (*binder_transfer_binder)(struct task_struct *from, - struct task_struct *to); - int (*binder_transfer_file)(struct task_struct *from, - struct task_struct *to, + int (*binder_set_context_mgr)(const struct cred *mgr); + int (*binder_transaction)(const struct cred *from, + const struct cred *to); + int (*binder_transfer_binder)(const struct cred *from, + const struct cred *to); + int (*binder_transfer_file)(const struct cred *from, + const struct cred *to, struct file *file);

int (*ptrace_access_check)(struct task_struct *child, --- a/include/linux/security.h +++ b/include/linux/security.h @@ -219,13 +219,13 @@ static inline void security_free_mnt_opt extern int security_init(void);

/* Security operations */ -int security_binder_set_context_mgr(struct task_struct *mgr); -int security_binder_transaction(struct task_struct *from, - struct task_struct *to); -int security_binder_transfer_binder(struct task_struct *from, - struct task_struct *to); -int security_binder_transfer_file(struct task_struct *from, - struct task_struct *to, struct file *file); +int security_binder_set_context_mgr(const struct cred *mgr); +int security_binder_transaction(const struct cred *from, + const struct cred *to); +int security_binder_transfer_binder(const struct cred *from, + const struct cred *to); +int security_binder_transfer_file(const struct cred *from, + const struct cred *to, struct file *file); int security_ptrace_access_check(struct task_struct *child, unsigned int mode); int security_ptrace_traceme(struct task_struct *parent); int security_capget(struct task_struct *target, @@ -442,25 +442,25 @@ static inline int security_init(void) return 0; }

-static inline int security_binder_set_context_mgr(struct task_struct *mgr) +static inline int security_binder_set_context_mgr(const struct cred *mgr) { return 0; }

-static inline int security_binder_transaction(struct task_struct *from, - struct task_struct *to) +static inline int security_binder_transaction(const struct cred *from, + const struct cred *to) { return 0; }

-static inline int security_binder_transfer_binder(struct task_struct *from, - struct task_struct *to) +static inline int security_binder_transfer_binder(const struct cred *from, + const struct cred *to) { return 0; }

-static inline int security_binder_transfer_file(struct task_struct *from, - struct task_struct *to, +static inline int security_binder_transfer_file(const struct cred *from, + const struct cred *to, struct file *file) { return 0; --- a/security/security.c +++ b/security/security.c @@ -232,25 +232,25 @@ EXPORT_SYMBOL(unregister_lsm_notifier);

/* Security operations */

-int security_binder_set_context_mgr(struct task_struct *mgr) +int security_binder_set_context_mgr(const struct cred *mgr) { return call_int_hook(binder_set_context_mgr, 0, mgr); }

-int security_binder_transaction(struct task_struct *from, - struct task_struct *to) +int security_binder_transaction(const struct cred *from, + const struct cred *to) { return call_int_hook(binder_transaction, 0, from, to); }

-int security_binder_transfer_binder(struct task_struct *from, - struct task_struct *to) +int security_binder_transfer_binder(const struct cred *from, + const struct cred *to) { return call_int_hook(binder_transfer_binder, 0, from, to); }

-int security_binder_transfer_file(struct task_struct *from, - struct task_struct *to, struct file *file) +int security_binder_transfer_file(const struct cred *from, + const struct cred *to, struct file *file) { return call_int_hook(binder_transfer_file, 0, from, to, file); } --- a/security/selinux/hooks.c +++ b/security/selinux/hooks.c @@ -2218,22 +2218,19 @@ static inline u32 open_file_to_av(struct

/* Hook functions begin here. */

-static int selinux_binder_set_context_mgr(struct task_struct *mgr) +static int selinux_binder_set_context_mgr(const struct cred *mgr) { - u32 mysid = current_sid(); - u32 mgrsid = task_sid(mgr); - return avc_has_perm(&selinux_state, - mysid, mgrsid, SECCLASS_BINDER, + current_sid(), cred_sid(mgr), SECCLASS_BINDER, BINDER__SET_CONTEXT_MGR, NULL); }

-static int selinux_binder_transaction(struct task_struct *from, - struct task_struct *to) +static int selinux_binder_transaction(const struct cred *from, + const struct cred *to) { u32 mysid = current_sid(); - u32 fromsid = task_sid(from); - u32 tosid = task_sid(to); + u32 fromsid = cred_sid(from); + u32 tosid = cred_sid(to); int rc;

if (mysid != fromsid) { @@ -2244,27 +2241,24 @@ static int selinux_binder_transaction(st return rc; }

- return avc_has_perm(&selinux_state, - fromsid, tosid, SECCLASS_BINDER, BINDER__CALL, - NULL); + return avc_has_perm(&selinux_state, fromsid, tosid, + SECCLASS_BINDER, BINDER__CALL, NULL); }

-static int selinux_binder_transfer_binder(struct task_struct *from, - struct task_struct *to) +static int selinux_binder_transfer_binder(const struct cred *from, + const struct cred *to) { - u32 fromsid = task_sid(from); - u32 tosid = task_sid(to); - return avc_has_perm(&selinux_state, - fromsid, tosid, SECCLASS_BINDER, BINDER__TRANSFER, + cred_sid(from), cred_sid(to), + SECCLASS_BINDER, BINDER__TRANSFER, NULL); }

-static int selinux_binder_transfer_file(struct task_struct *from, - struct task_struct *to, +static int selinux_binder_transfer_file(const struct cred *from, + const struct cred *to, struct file *file) { - u32 sid = task_sid(to); + u32 sid = cred_sid(to); struct file_security_struct *fsec = file->f_security; struct dentry *dentry = file->f_path.dentry; struct inode_security_struct *isec;

From: Takashi Iwai tiwai@suse.de

commit 16e28abb7290c4ca3b3a0f333ba067f34bb18c86 upstream.

Fujitsu Lifebook T725 laptop requires, like a few other similar models, the nomux and notimeout options to probe the touchpad properly. This patch adds the corresponding quirk entries.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980 Tested-by: Neal Gompa ngompa13@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Takashi Iwai tiwai@suse.de Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de Signed-off-by: Dmitry Torokhov dmitry.torokhov@gmail.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/input/serio/i8042-x86ia64io.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+)

--- a/drivers/input/serio/i8042-x86ia64io.h +++ b/drivers/input/serio/i8042-x86ia64io.h @@ -277,6 +277,13 @@ static const struct dmi_system_id __init }, }, { + /* Fujitsu Lifebook T725 laptop */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"), + DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK T725"), + }, + }, + { /* Fujitsu Lifebook U745 */ .matches = { DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"), @@ -845,6 +852,13 @@ static const struct dmi_system_id __init }, }, { + /* Fujitsu Lifebook T725 laptop */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"), + DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK T725"), + }, + }, + { /* Fujitsu U574 laptop */ /* https://bugzilla.kernel.org/show_bug.cgi?id=69731 */ .matches = {

From: Jan Kara jack@suse.cz

commit 839b63860eb3835da165642923120d305925561d upstream.

Patch series "ocfs2: Truncate data corruption fix".

As further testing has shown, commit 5314454ea3f ("ocfs2: fix data corruption after conversion from inline format") didn't fix all the data corruption issues the customer started observing after 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") This time I have tracked them down to two bugs in ocfs2 truncation code.

One bug (truncating page cache before clearing tail cluster and setting i_size) could cause data corruption even before 6dbf7bb55598, but before that commit it needed a race with page fault, after 6dbf7bb55598 it started to be pretty deterministic.

Another bug (zeroing pages beyond old i_size) used to be harmless inefficiency before commit 6dbf7bb55598. But after commit 6dbf7bb55598 in combination with the first bug it resulted in deterministic data corruption.

Although fixing only the first problem is needed to stop data corruption, I've fixed both issues to make the code more robust.

This patch (of 2):

ocfs2_truncate_file() did unmap invalidate page cache pages before zeroing partial tail cluster and setting i_size. Thus some pages could be left (and likely have left if the cluster zeroing happened) in the page cache beyond i_size after truncate finished letting user possibly see stale data once the file was extended again. Also the tail cluster zeroing was not guaranteed to finish before truncate finished causing possible stale data exposure. The problem started to be particularly easy to hit after commit 6dbf7bb55598 "fs: Don't invalidate page buffers in block_write_full_page()" stopped invalidation of pages beyond i_size from page writeback path.

Fix these problems by unmapping and invalidating pages in the page cache after the i_size is reduced and tail cluster is zeroed out.

Link: https://lkml.kernel.org/r/20211025150008.29002-1-jack@suse.cz Link: https://lkml.kernel.org/r/20211025151332.11301-1-jack@suse.cz Fixes: ccd979bdbce9 ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem") Signed-off-by: Jan Kara jack@suse.cz Reviewed-by: Joseph Qi joseph.qi@linux.alibaba.com Cc: Mark Fasheh mark@fasheh.com Cc: Joel Becker jlbec@evilplan.org Cc: Junxiao Bi junxiao.bi@oracle.com Cc: Changwei Ge gechangwei@live.cn Cc: Gang He ghe@suse.com Cc: Jun Piao piaojun@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton akpm@linux-foundation.org Signed-off-by: Linus Torvalds torvalds@linux-foundation.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- fs/ocfs2/file.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)

--- a/fs/ocfs2/file.c +++ b/fs/ocfs2/file.c @@ -492,10 +492,11 @@ int ocfs2_truncate_file(struct inode *in * greater than page size, so we have to truncate them * anyway. */ - unmap_mapping_range(inode->i_mapping, new_i_size + PAGE_SIZE - 1, 0, 1); - truncate_inode_pages(inode->i_mapping, new_i_size);

if (OCFS2_I(inode)->ip_dyn_features & OCFS2_INLINE_DATA_FL) { + unmap_mapping_range(inode->i_mapping, + new_i_size + PAGE_SIZE - 1, 0, 1); + truncate_inode_pages(inode->i_mapping, new_i_size); status = ocfs2_truncate_inline(inode, di_bh, new_i_size, i_size_read(inode), 1); if (status) @@ -514,6 +515,9 @@ int ocfs2_truncate_file(struct inode *in goto bail_unlock_sem; }

+ unmap_mapping_range(inode->i_mapping, new_i_size + PAGE_SIZE - 1, 0, 1); + truncate_inode_pages(inode->i_mapping, new_i_size); + status = ocfs2_commit_truncate(osb, inode, di_bh); if (status < 0) { mlog_errno(status);

From: Helge Deller deller@gmx.de

commit 8779e05ba8aaffec1829872ef9774a71f44f6580 upstream.

The TIF_XXX flags are stored in the flags field in the thread_info struct (TI_FLAGS), not in the flags field of the task_struct structure (TASK_FLAGS).

It seems this bug didn't generate any important side-effects, otherwise it wouldn't have went unnoticed for 12 years (since v2.6.32).

Signed-off-by: Helge Deller deller@gmx.de Fixes: ecd3d4bc06e48 ("parisc: stop using task->ptrace for {single,block}step flags") Cc: Kyle McMartin kyle@mcmartin.ca Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/parisc/kernel/entry.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/parisc/kernel/entry.S +++ b/arch/parisc/kernel/entry.S @@ -1851,7 +1851,7 @@ syscall_restore: LDREG TI_TASK-THREAD_SZ_ALGN-FRAME_SIZE(%r30),%r1

/* Are we being ptraced? */ - ldw TASK_FLAGS(%r1),%r19 + LDREG TI_FLAGS-THREAD_SZ_ALGN-FRAME_SIZE(%r30),%r19 ldi _TIF_SYSCALL_TRACE_MASK,%r2 and,COND(=) %r19,%r2,%r0 b,n syscall_restore_rfi

From: jing yangyang cgel.zte@gmail.com

commit 2ac5fb35cd520ab1851c9a4816c523b65276052f upstream.

sizeof when applied to a pointer typed expression gives the size of the pointer.

./drivers/firmware/psci/psci_checker.c:158:41-47: ERROR application of sizeof to pointer

This issue was detected with the help of Coccinelle.

Fixes: 7401056de5f8 ("drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests") Cc: stable@vger.kernel.org Reported-by: Zeal Robot zealci@zte.com.cn Acked-by: Mark Rutland mark.rutland@arm.com Reviewed-by: Gustavo A. R. Silva gustavoars@kernel.org Signed-off-by: jing yangyang jing.yangyang@zte.com.cn Signed-off-by: Gustavo A. R. Silva gustavoars@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/firmware/psci_checker.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/firmware/psci_checker.c +++ b/drivers/firmware/psci_checker.c @@ -162,7 +162,7 @@ static int alloc_init_cpu_groups(cpumask if (!alloc_cpumask_var(&tmp, GFP_KERNEL)) return -ENOMEM;

- cpu_groups = kcalloc(nb_available_cpus, sizeof(cpu_groups), + cpu_groups = kcalloc(nb_available_cpus, sizeof(*cpu_groups), GFP_KERNEL); if (!cpu_groups) { free_cpumask_var(tmp);

From: Sean Young sean@mess.org

commit fdc881783099c6343921ff017450831c8766d12a upstream.

On an Intel NUC6iSYK, no IR is reported after a receive overflow.

When a receiver overflow occurs, this condition is only cleared by reading the fifo. Make sure we read anything in the fifo.

Fixes: 28c7afb07ccf ("media: ite-cir: check for receive overflow") Suggested-by: Bryan Pass bryan.pass@gmail.com Tested-by: Bryan Pass bryan.pass@gmail.com Cc: stable@vger.kernel.org> Signed-off-by: Sean Young sean@mess.org Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/media/rc/ite-cir.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/media/rc/ite-cir.c +++ b/drivers/media/rc/ite-cir.c @@ -292,7 +292,7 @@ static irqreturn_t ite_cir_isr(int irq, }

/* check for the receive interrupt */ - if (iflags & ITE_IRQ_RX_FIFO) { + if (iflags & (ITE_IRQ_RX_FIFO | ITE_IRQ_RX_FIFO_OVERRUN)) { /* read the FIFO bytes */ rx_bytes = dev->params.get_rx_bytes(dev, rx_buf,

From: Tim Crawford tcrawford@system76.com

commit dbfe83507cf4ea66ce4efee2ac14c5ad420e31d3 upstream.

Apply the PB51ED PCI quirk to the Clevo PC70HS. Fixes audio output from the internal speakers.

Signed-off-by: Tim Crawford tcrawford@system76.com Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211101162134.5336-1-tcrawford@system76.com Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+)

--- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -2525,6 +2525,7 @@ static const struct snd_pci_quirk alc882 SND_PCI_QUIRK(0x1558, 0x67d1, "Clevo PB71[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS), SND_PCI_QUIRK(0x1558, 0x67e1, "Clevo PB71[DE][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS), SND_PCI_QUIRK(0x1558, 0x67e5, "Clevo PC70D[PRS](?:-D|-G)?", ALC1220_FIXUP_CLEVO_PB51ED_PINS), + SND_PCI_QUIRK(0x1558, 0x67f1, "Clevo PC70H[PRS]", ALC1220_FIXUP_CLEVO_PB51ED_PINS), SND_PCI_QUIRK(0x1558, 0x70d1, "Clevo PC70[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS), SND_PCI_QUIRK(0x1558, 0x7714, "Clevo X170SM", ALC1220_FIXUP_CLEVO_PB51ED_PINS), SND_PCI_QUIRK(0x1558, 0x7715, "Clevo X170KM-G", ALC1220_FIXUP_CLEVO_PB51ED),

From: Johan Hovold johan@kernel.org

commit 9b371c6cc37f954360989eec41c2ddc5a6b83917 upstream.

USB control and bulk message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ.

Fixes: c6d43ba816d1 ("ALSA: usb/6fire - Driver for TerraTec DMX 6Fire USB") Cc: stable@vger.kernel.org # 2.6.39 Signed-off-by: Johan Hovold johan@kernel.org Link: https://lore.kernel.org/r/20211025121142.6531-2-johan@kernel.org Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- sound/usb/6fire/comm.c | 2 +- sound/usb/6fire/firmware.c | 6 +++--- 2 files changed, 4 insertions(+), 4 deletions(-)

--- a/sound/usb/6fire/comm.c +++ b/sound/usb/6fire/comm.c @@ -99,7 +99,7 @@ static int usb6fire_comm_send_buffer(u8 int actual_len;

ret = usb_interrupt_msg(dev, usb_sndintpipe(dev, COMM_EP), - buffer, buffer[1] + 2, &actual_len, HZ); + buffer, buffer[1] + 2, &actual_len, 1000); if (ret < 0) return ret; else if (actual_len != buffer[1] + 2) --- a/sound/usb/6fire/firmware.c +++ b/sound/usb/6fire/firmware.c @@ -166,7 +166,7 @@ static int usb6fire_fw_ezusb_write(struc

ret = usb_control_msg(device, usb_sndctrlpipe(device, 0), type, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - value, 0, data, len, HZ); + value, 0, data, len, 1000); if (ret < 0) return ret; else if (ret != len) @@ -179,7 +179,7 @@ static int usb6fire_fw_ezusb_read(struct { int ret = usb_control_msg(device, usb_rcvctrlpipe(device, 0), type, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, value, - 0, data, len, HZ); + 0, data, len, 1000); if (ret < 0) return ret; else if (ret != len) @@ -194,7 +194,7 @@ static int usb6fire_fw_fpga_write(struct int ret;

ret = usb_bulk_msg(device, usb_sndbulkpipe(device, FPGA_EP), data, len, - &actual_len, HZ); + &actual_len, 1000); if (ret < 0) return ret; else if (actual_len != len)

From: Alexander Tsoy alexander@tsoy.me

commit 763d92ed5dece7d439fc28a88b2d2728d525ffd9 upstream.

Add another device ID for JBL Quantum 400. It requires the same quirk as other JBL Quantum devices.

Signed-off-by: Alexander Tsoy alexander@tsoy.me Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211030174308.1011825-1-alexander@tsoy.me Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- sound/usb/quirks.c | 1 + 1 file changed, 1 insertion(+)

--- a/sound/usb/quirks.c +++ b/sound/usb/quirks.c @@ -1555,6 +1555,7 @@ static const struct registration_quirk r REG_QUIRK_ENTRY(0x0951, 0x16ea, 2), /* Kingston HyperX Cloud Flight S */ REG_QUIRK_ENTRY(0x0ecb, 0x1f46, 2), /* JBL Quantum 600 */ REG_QUIRK_ENTRY(0x0ecb, 0x1f47, 2), /* JBL Quantum 800 */ + REG_QUIRK_ENTRY(0x0ecb, 0x1f4c, 2), /* JBL Quantum 400 */ REG_QUIRK_ENTRY(0x0ecb, 0x2039, 2), /* JBL Quantum 400 */ REG_QUIRK_ENTRY(0x0ecb, 0x203c, 2), /* JBL Quantum 600 */ REG_QUIRK_ENTRY(0x0ecb, 0x203e, 2), /* JBL Quantum 800 */

From: Wang Wensheng wangwensheng4@huawei.com

commit c0317c0e87094f5b5782b6fdef5ae0a4b150496c upstream.

When the timer instance was add into ack_list but was not currently in process, the user could stop it via snd_timer_stop1() without delete it from the ack_list. Then the user could free the timer instance and when it was actually processed UAF occurred.

This issue could be reproduced via testcase snd_timer01 in ltp - running several instances of that testcase at the same time.

What I actually met was that the ack_list of the timer broken and the kernel went into deadloop with irqoff. That could be detected by hardlockup detector on board or when we run it on qemu, we could use gdb to dump the ack_list when the console has no response.

To fix this issue, we delete the timer instance from ack_list and active_list unconditionally in snd_timer_stop1().

Signed-off-by: Wang Wensheng wangwensheng4@huawei.com Suggested-by: Takashi Iwai tiwai@suse.de Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- sound/core/timer.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/sound/core/timer.c +++ b/sound/core/timer.c @@ -593,13 +593,13 @@ static int snd_timer_stop1(struct snd_ti if (!timer) return -EINVAL; spin_lock_irqsave(&timer->lock, flags); + list_del_init(&timeri->ack_list); + list_del_init(&timeri->active_list); if (!(timeri->flags & (SNDRV_TIMER_IFLG_RUNNING | SNDRV_TIMER_IFLG_START))) { result = -EBUSY; goto unlock; } - list_del_init(&timeri->ack_list); - list_del_init(&timeri->active_list); if (timer->card && timer->card->shutdown) goto unlock; if (stop) {

From: Miklos Szeredi mszeredi@redhat.com

commit 712a951025c0667ff00b25afc360f74e639dfabe upstream.

It is possible to trigger a crash by splicing anon pipe bufs to the fuse device.

The reason for this is that anon_pipe_buf_release() will reuse buf->page if the refcount is 1, but that page might have already been stolen and its flags modified (e.g. PG_lru added).

This happens in the unlikely case of fuse_dev_splice_write() getting around to calling pipe_buf_release() after a page has been stolen, added to the page cache and removed from the page cache.

Fix by calling pipe_buf_release() right after the page was inserted into the page cache. In this case the page has an elevated refcount so any release function will know that the page isn't reusable.

Reported-by: Frank Dinoff fdinoff@google.com Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1y... Fixes: dd3bb14f44a6 ("fuse: support splice() writing to fuse device") Cc: stable@vger.kernel.org # v2.6.35 Signed-off-by: Miklos Szeredi mszeredi@redhat.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- fs/fuse/dev.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-)

--- a/fs/fuse/dev.c +++ b/fs/fuse/dev.c @@ -905,6 +905,12 @@ static int fuse_try_move_page(struct fus goto out_put_old; }

+ /* + * Release while we have extra ref on stolen page. Otherwise + * anon_pipe_buf_release() might think the page can be reused. + */ + pipe_buf_release(cs->pipe, buf); + get_page(newpage);

if (!(buf->flags & PIPE_BUF_FLAG_LRU)) @@ -2054,8 +2060,12 @@ static ssize_t fuse_dev_splice_write(str

pipe_lock(pipe); out_free: - for (idx = 0; idx < nbuf; idx++) - pipe_buf_release(pipe, &bufs[idx]); + for (idx = 0; idx < nbuf; idx++) { + struct pipe_buffer *buf = &bufs[idx]; + + if (buf->ops) + pipe_buf_release(pipe, buf); + } pipe_unlock(pipe);

kvfree(bufs);

From: Sean Christopherson seanjc@google.com

commit 6ff53f6a438f72998f56e82e76694a1df9d1ea2c upstream.

Add a synchronize_rcu() after clearing the posted interrupt wakeup handler to ensure all readers, i.e. in-flight IRQ handlers, see the new handler before returning to the caller. If the caller is an exiting module and is unregistering its handler, failure to wait could result in the IRQ handler jumping into an unloaded module.

The registration path doesn't require synchronization, as it's the caller's responsibility to not generate interrupts it cares about until after its handler is registered.

Fixes: f6b3c72c2366 ("x86/irq: Define a global vector for VT-d Posted-Interrupts") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson seanjc@google.com Message-Id: 20211009001107.3936588-2-seanjc@google.com Signed-off-by: Paolo Bonzini pbonzini@redhat.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/x86/kernel/irq.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/arch/x86/kernel/irq.c +++ b/arch/x86/kernel/irq.c @@ -290,8 +290,10 @@ void kvm_set_posted_intr_wakeup_handler( { if (handler) kvm_posted_intr_wakeup_handler = handler; - else + else { kvm_posted_intr_wakeup_handler = dummy_handler; + synchronize_rcu(); + } } EXPORT_SYMBOL_GPL(kvm_set_posted_intr_wakeup_handler);

From: Dmitry Bogdanov d.bogdanov@yadro.com

[ Upstream commit 4a8f71014b4d56c4fb287607e844c0a9f68f46d9 ]

The sgl is freed in the target stack in target_release_cmd_kref() before calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that causes a panic if sgl is not yet DMA unmapped:

NIP dma_direct_unmap_sg+0xdc/0x180 LR dma_direct_unmap_sg+0xc8/0x180 Call Trace: ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable) dma_unmap_sg_attrs+0x54/0xf0 qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx] qlt_free_cmd+0x124/0x1d0 [qla2xxx] tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx] target_put_sess_cmd+0x198/0x370 [target_core_mod] transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod] tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]

The sgl may be left unmapped in error cases of response sending. For instance, qlt_rdy_to_xfer() maps sgl and exits when session is being deleted keeping the sgl mapped.

This patch removes use-after-free of the sgl and ensures that the sgl is unmapped for any command that was not sent to firmware.

Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com Reviewed-by: Himanshu Madhani himanshu.madhani@oracle.com Signed-off-by: Dmitry Bogdanov d.bogdanov@yadro.com Signed-off-by: Martin K. Petersen martin.petersen@oracle.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/scsi/qla2xxx/qla_target.c | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_target.c b/drivers/scsi/qla2xxx/qla_target.c index ec54c8f34bc84..5fbac85d7adfb 100644 --- a/drivers/scsi/qla2xxx/qla_target.c +++ b/drivers/scsi/qla2xxx/qla_target.c @@ -3216,8 +3216,7 @@ int qlt_xmit_response(struct qla_tgt_cmd *cmd, int xmit_type, "RESET-RSP online/active/old-count/new-count = %d/%d/%d/%d.\n", vha->flags.online, qla2x00_reset_active(vha), cmd->reset_count, qpair->chip_reset); - spin_unlock_irqrestore(qpair->qp_lock_ptr, flags); - return 0; + goto out_unmap_unlock; }

/* Does F/W have an IOCBs for this request */ @@ -3339,10 +3338,6 @@ int qlt_rdy_to_xfer(struct qla_tgt_cmd *cmd) prm.sg = NULL; prm.req_cnt = 1;

- /* Calculate number of entries and segments required */ - if (qlt_pci_map_calc_cnt(&prm) != 0) - return -EAGAIN; - if (!qpair->fw_started || (cmd->reset_count != qpair->chip_reset) || (cmd->sess && cmd->sess->deleted)) { /* @@ -3358,6 +3353,10 @@ int qlt_rdy_to_xfer(struct qla_tgt_cmd *cmd) return 0; }

+ /* Calculate number of entries and segments required */ + if (qlt_pci_map_calc_cnt(&prm) != 0) + return -EAGAIN; + spin_lock_irqsave(qpair->qp_lock_ptr, flags); /* Does F/W have an IOCBs for this request */ res = qlt_check_reserve_free_req(qpair, prm.req_cnt); @@ -3785,9 +3784,6 @@ void qlt_free_cmd(struct qla_tgt_cmd *cmd)

BUG_ON(cmd->cmd_in_wq);

- if (cmd->sg_mapped) - qlt_unmap_sg(cmd->vha, cmd); - if (!cmd->q_full) qlt_decr_num_pend_cmds(cmd->vha);

From: Erik Ekman erik@kryo.se

[ Upstream commit bf6abf345dfa77786aca554bc58c64bd428ecb1d ]

Use pci_info instead to avoid unnamed/uninitialized noise:

[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected [197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F [197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed [197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support

Inspired by fa44821a4ddd ("sfc: don't use netif_info et al before net_device is registered") from Heiner Kallweit.

Signed-off-by: Erik Ekman erik@kryo.se Acked-by: Martin Habets habetsm.xilinx@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/ethernet/sfc/ptp.c | 4 ++-- drivers/net/ethernet/sfc/siena_sriov.c | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/sfc/ptp.c b/drivers/net/ethernet/sfc/ptp.c index d47151dbe804d..c0a810f740341 100644 --- a/drivers/net/ethernet/sfc/ptp.c +++ b/drivers/net/ethernet/sfc/ptp.c @@ -651,7 +651,7 @@ static int efx_ptp_get_attributes(struct efx_nic *efx) } else if (rc == -EINVAL) { fmt = MC_CMD_PTP_OUT_GET_ATTRIBUTES_SECONDS_NANOSECONDS; } else if (rc == -EPERM) { - netif_info(efx, probe, efx->net_dev, "no PTP support\n"); + pci_info(efx->pci_dev, "no PTP support\n"); return rc; } else { efx_mcdi_display_error(efx, MC_CMD_PTP, sizeof(inbuf), @@ -827,7 +827,7 @@ static int efx_ptp_disable(struct efx_nic *efx) * should only have been called during probe. */ if (rc == -ENOSYS || rc == -EPERM) - netif_info(efx, probe, efx->net_dev, "no PTP support\n"); + pci_info(efx->pci_dev, "no PTP support\n"); else if (rc) efx_mcdi_display_error(efx, MC_CMD_PTP, MC_CMD_PTP_IN_DISABLE_LEN, diff --git a/drivers/net/ethernet/sfc/siena_sriov.c b/drivers/net/ethernet/sfc/siena_sriov.c index da7b94f346049..30d58f72725df 100644 --- a/drivers/net/ethernet/sfc/siena_sriov.c +++ b/drivers/net/ethernet/sfc/siena_sriov.c @@ -1059,7 +1059,7 @@ void efx_siena_sriov_probe(struct efx_nic *efx) return;

if (efx_siena_sriov_cmd(efx, false, &efx->vi_scale, &count)) { - netif_info(efx, probe, efx->net_dev, "no SR-IOV VFs probed\n"); + pci_info(efx->pci_dev, "no SR-IOV VFs probed\n"); return; } if (count > 0 && count > max_vfs)

From: Randy Dunlap rdunlap@infradead.org

[ Upstream commit 162079f2dccd02cb4b6654defd32ca387dd6d4d4 ]

The Winbond MMC driver fails to build on ARCH=m68k so prevent that build config. Silences these build errors:

../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end': ../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration] 212 | dmaflags = claim_dma_lock(); ../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration] 215 | release_dma_lock(dmaflags);

Signed-off-by: Randy Dunlap rdunlap@infradead.org Cc: Pierre Ossman pierre@ossman.eu Cc: Geert Uytterhoeven geert@linux-m68k.org Cc: Arnd Bergmann arnd@arndb.de Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mmc/host/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index b7f809aa40c2c..2c11944686cf9 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -421,7 +421,7 @@ config MMC_OMAP_HS

config MMC_WBSD tristate "Winbond W83L51xD SD/MMC Card Interface support" - depends on ISA_DMA_API + depends on ISA_DMA_API && !M68K help This selects the Winbond(R) W83L51xD Secure digital and Multimedia card Interface.

From: Lorenz Bauer lmb@cloudflare.com

[ Upstream commit fadb7ff1a6c2c565af56b4aacdd086b067eed440 ]

Restrict bpf_jit_limit to the maximum supported by the arch's JIT.

Signed-off-by: Lorenz Bauer lmb@cloudflare.com Signed-off-by: Alexei Starovoitov ast@kernel.org Link: https://lore.kernel.org/bpf/20211014142554.53120-4-lmb@cloudflare.com Signed-off-by: Sasha Levin sashal@kernel.org --- include/linux/filter.h | 1 + kernel/bpf/core.c | 4 +++- net/core/sysctl_net_core.c | 2 +- 3 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/include/linux/filter.h b/include/linux/filter.h index e981bd92a4e3a..89a6ef659b4ca 100644 --- a/include/linux/filter.h +++ b/include/linux/filter.h @@ -877,6 +877,7 @@ extern int bpf_jit_enable; extern int bpf_jit_harden; extern int bpf_jit_kallsyms; extern long bpf_jit_limit; +extern long bpf_jit_limit_max;

typedef void (*bpf_jit_fill_hole_t)(void *area, unsigned int size);

diff --git a/kernel/bpf/core.c b/kernel/bpf/core.c index 341402bc1202d..4e5b5ae05406e 100644 --- a/kernel/bpf/core.c +++ b/kernel/bpf/core.c @@ -372,6 +372,7 @@ int bpf_jit_enable __read_mostly = IS_BUILTIN(CONFIG_BPF_JIT_ALWAYS_ON); int bpf_jit_harden __read_mostly; int bpf_jit_kallsyms __read_mostly; long bpf_jit_limit __read_mostly; +long bpf_jit_limit_max __read_mostly;

static __always_inline void bpf_get_prog_addr_region(const struct bpf_prog *prog, @@ -598,7 +599,8 @@ u64 __weak bpf_jit_alloc_exec_limit(void) static int __init bpf_jit_charge_init(void) { /* Only used as heuristic here to derive limit. */ - bpf_jit_limit = min_t(u64, round_up(bpf_jit_alloc_exec_limit() >> 2, + bpf_jit_limit_max = bpf_jit_alloc_exec_limit(); + bpf_jit_limit = min_t(u64, round_up(bpf_jit_limit_max >> 2, PAGE_SIZE), LONG_MAX); return 0; } diff --git a/net/core/sysctl_net_core.c b/net/core/sysctl_net_core.c index 2597449ae9b48..0a0bf80623658 100644 --- a/net/core/sysctl_net_core.c +++ b/net/core/sysctl_net_core.c @@ -417,7 +417,7 @@ static struct ctl_table net_core_table[] = { .mode = 0600, .proc_handler = proc_dolongvec_minmax_bpf_restricted, .extra1 = &long_one, - .extra2 = &long_max, + .extra2 = &bpf_jit_limit_max, }, #endif {

From: Thomas Perrot thomas.perrot@bootlin.com

[ Upstream commit d81d0e41ed5fe7229a2c9a29d13bad288c7cf2d2 ]

There are missing braces in the function that verify controller parameters, then an error is always returned when the parameter to select Microwire frames operation is used on devices allowing it.

Signed-off-by: Thomas Perrot thomas.perrot@bootlin.com Link: https://lore.kernel.org/r/20211022142104.1386379-1-thomas.perrot@bootlin.com Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/spi/spi-pl022.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c index 1af8c96b940e2..aa04ff6e01b9d 100644 --- a/drivers/spi/spi-pl022.c +++ b/drivers/spi/spi-pl022.c @@ -1703,12 +1703,13 @@ static int verify_controller_parameters(struct pl022 *pl022, return -EINVAL; } } else { - if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) + if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) { dev_err(&pl022->adev->dev, "Microwire half duplex mode requested," " but this is only available in the" " ST version of PL022\n"); - return -EINVAL; + return -EINVAL; + } } } return 0;

From: Dongli Zhang dongli.zhang@oracle.com

[ Upstream commit 9159f102402a64ac85e676b75cc1f9c62c5b4b73 ]

The netif_device_detach() conditionally stops all tx queues if the queues are running. There is no need to call netif_tx_stop_all_queues() again.

Signed-off-by: Dongli Zhang dongli.zhang@oracle.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/vmxnet3/vmxnet3_drv.c | 1 - 1 file changed, 1 deletion(-)

diff --git a/drivers/net/vmxnet3/vmxnet3_drv.c b/drivers/net/vmxnet3/vmxnet3_drv.c index e454dfc9ad8f2..c004819bebe35 100644 --- a/drivers/net/vmxnet3/vmxnet3_drv.c +++ b/drivers/net/vmxnet3/vmxnet3_drv.c @@ -3634,7 +3634,6 @@ vmxnet3_suspend(struct device *device) vmxnet3_free_intr_resources(adapter);

netif_device_detach(netdev); - netif_tx_stop_all_queues(netdev);

/* Create wake-up filters. */ pmConf = adapter->pm_conf;

From: Filipe Manana fdmanana@suse.com

commit 10adb1152d957a4d570ad630f93a88bb961616c1 upstream.

At replay_dir_deletes(), if find_dir_range() returns an error we break out of the main while loop and then assign a value of 0 (success) to the 'ret' variable, resulting in completely ignoring that an error happened. Fix that by jumping to the 'out' label when find_dir_range() returns an error (negative value).

CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik josef@toxicpanda.com Signed-off-by: Filipe Manana fdmanana@suse.com Signed-off-by: David Sterba dsterba@suse.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- fs/btrfs/tree-log.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -2412,7 +2412,9 @@ again: else { ret = find_dir_range(log, path, dirid, key_type, &range_start, &range_end); - if (ret != 0) + if (ret < 0) + goto out; + else if (ret > 0) break; }

From: Masami Hiramatsu mhiramat@kernel.org

commit a7fe2378454cf46cd5e2776d05e72bbe8f0a468c upstream.

The following commit:

Commit e792ff804f49 ("ia64: kprobes: Use generic kretprobe trampoline handler")

Passed the wrong trampoline address to __kretprobe_trampoline_handler(): it passes the descriptor address instead of function entry address.

Pass the right parameter.

Also use correct symbol dereference function to get the function address from 'kretprobe_trampoline' - an IA64 special.

Link: https://lkml.kernel.org/r/163163042696.489837.12551102356265354730.stgit@dev...

Fixes: e792ff804f49 ("ia64: kprobes: Use generic kretprobe trampoline handler") Cc: Josh Poimboeuf jpoimboe@redhat.com Cc: Ingo Molnar mingo@kernel.org Cc: X86 ML x86@kernel.org Cc: Daniel Xu dxu@dxuuu.xyz Cc: Thomas Gleixner tglx@linutronix.de Cc: Borislav Petkov bp@alien8.de Cc: Peter Zijlstra peterz@infradead.org Cc: Abhishek Sagar sagar.abhishek@gmail.com Cc: Andrii Nakryiko andrii.nakryiko@gmail.com Cc: Paul McKenney paulmck@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu mhiramat@kernel.org Signed-off-by: Steven Rostedt (VMware) rostedt@goodmis.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/ia64/kernel/kprobes.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)

--- a/arch/ia64/kernel/kprobes.c +++ b/arch/ia64/kernel/kprobes.c @@ -411,7 +411,8 @@ static void kretprobe_trampoline(void)

int __kprobes trampoline_probe_handler(struct kprobe *p, struct pt_regs *regs) { - regs->cr_iip = __kretprobe_trampoline_handler(regs, kretprobe_trampoline, NULL); + regs->cr_iip = __kretprobe_trampoline_handler(regs, + dereference_function_descriptor(kretprobe_trampoline), NULL); /* * By returning a non-zero value, we are telling * kprobe_handler() that we don't want the post_handler @@ -427,7 +428,7 @@ void __kprobes arch_prepare_kretprobe(st ri->fp = NULL;

/* Replace the return addr with trampoline addr */ - regs->b0 = ((struct fnptr *)kretprobe_trampoline)->ip; + regs->b0 = (unsigned long)dereference_function_descriptor(kretprobe_trampoline); }

/* Check the instruction in the slot is break */ @@ -957,14 +958,14 @@ static struct kprobe trampoline_p = { int __init arch_init_kprobes(void) { trampoline_p.addr = - (kprobe_opcode_t *)((struct fnptr *)kretprobe_trampoline)->ip; + dereference_function_descriptor(kretprobe_trampoline); return register_kprobe(&trampoline_p); }

int __kprobes arch_trampoline_kprobe(struct kprobe *p) { if (p->addr == - (kprobe_opcode_t *)((struct fnptr *)kretprobe_trampoline)->ip) + dereference_function_descriptor(kretprobe_trampoline)) return 1;

return 0;

From: Krzysztof Kozlowski krzysztof.kozlowski@canonical.com

commit b16bef60a9112b1e6daf3afd16484eb06e7ce792 upstream.

The driver and its bindings, before commit 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4") were requiring to provide at least one safe/default voltage for DVS registers if DVS GPIO is not being enabled.

IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the s5m8767,pmic-buck2-dvs-voltage should still be present and contain one voltage.

This requirement was coming from driver behavior matching this condition (none of DVS GPIO is enabled): it was always initializing the DVS selector pins to 0 and keeping the DVS enable setting at reset value (enabled). Therefore if none of DVS GPIO is enabled in devicetree, driver was configuring the first DVS voltage for buck[234].

Mentioned commit 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4") broke it because DVS voltage won't be parsed from devicetree if DVS GPIO is not enabled. After the change, driver will configure bucks to use the register reset value as voltage which might have unpleasant effects.

Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled in devicetree (therefore DVS voltage is also not parsed), explicitly disable it.

Cc: stable@vger.kernel.org Fixes: 04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4") Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@canonical.com Acked-by: Rob Herring robh@kernel.org Message-Id: 20211008113723.134648-2-krzysztof.kozlowski@canonical.com Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt | 21 +++------- drivers/regulator/s5m8767.c | 21 ++++------ 2 files changed, 17 insertions(+), 25 deletions(-)

--- a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt +++ b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt @@ -13,6 +13,14 @@ common regulator binding documented in:

Required properties of the main device node (the parent!): + - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + + [1] If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties of the main device node (the parent!): - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) units for buck2 when changing voltage using gpio dvs. Refer to [1] below for additional information. @@ -25,19 +33,6 @@ Required properties of the main device n units for buck4 when changing voltage using gpio dvs. Refer to [1] below for additional information.

- - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used - for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. - - [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' - property should specify atleast one voltage level (which would be a - safe operating voltage). - - If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, then all the eight voltage values for the - 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. - -Optional properties of the main device node (the parent!): - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. --- a/drivers/regulator/s5m8767.c +++ b/drivers/regulator/s5m8767.c @@ -849,18 +849,15 @@ static int s5m8767_pmic_probe(struct pla /* DS4 GPIO */ gpio_direction_output(pdata->buck_ds[2], 0x0);

- if (pdata->buck2_gpiodvs || pdata->buck3_gpiodvs || - pdata->buck4_gpiodvs) { - regmap_update_bits(s5m8767->iodev->regmap_pmic, - S5M8767_REG_BUCK2CTRL, 1 << 1, - (pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1)); - regmap_update_bits(s5m8767->iodev->regmap_pmic, - S5M8767_REG_BUCK3CTRL, 1 << 1, - (pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1)); - regmap_update_bits(s5m8767->iodev->regmap_pmic, - S5M8767_REG_BUCK4CTRL, 1 << 1, - (pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1)); - } + regmap_update_bits(s5m8767->iodev->regmap_pmic, + S5M8767_REG_BUCK2CTRL, 1 << 1, + (pdata->buck2_gpiodvs) ? (1 << 1) : (0 << 1)); + regmap_update_bits(s5m8767->iodev->regmap_pmic, + S5M8767_REG_BUCK3CTRL, 1 << 1, + (pdata->buck3_gpiodvs) ? (1 << 1) : (0 << 1)); + regmap_update_bits(s5m8767->iodev->regmap_pmic, + S5M8767_REG_BUCK4CTRL, 1 << 1, + (pdata->buck4_gpiodvs) ? (1 << 1) : (0 << 1));

/* Initialize GPIO DVS registers */ for (i = 0; i < 8; i++) {

From: Eric Badger ebadger@purestorage.com

commit 537bddd069c743759addf422d0b8f028ff0f8dbc upstream.

The computation of TOHM is off by one bit. This missed bit results in too low a value for TOHM, which can cause errors in regular memory to incorrectly report:

EDAC MC0: 1 CE Error at MMIOH area, on addr 0x000000207fffa680 on any memory

Fixes: 50d1bb93672f ("sb_edac: add support for Haswell based systems") Cc: stable@vger.kernel.org Reported-by: Meeta Saggi msaggi@purestorage.com Signed-off-by: Eric Badger ebadger@purestorage.com Signed-off-by: Tony Luck tony.luck@intel.com Link: https://lore.kernel.org/r/20211010170127.848113-1-ebadger@purestorage.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/edac/sb_edac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/edac/sb_edac.c +++ b/drivers/edac/sb_edac.c @@ -1021,7 +1021,7 @@ static u64 haswell_get_tohm(struct sbrid pci_read_config_dword(pvt->info.pci_vtd, HASWELL_TOHM_1, &reg); rc = ((reg << 6) | rc) << 26;

- return rc | 0x1ffffff; + return rc | 0x3ffffff; }

static u64 knl_get_tolm(struct sbridge_pvt *pvt)

From: Johan Hovold johan@kernel.org

commit c1b9ca365deae667192be9fe24db244919971234 upstream.

Add the missing endpoint max-packet sanity check to probe() to avoid division by zero in ath10k_usb_hif_tx_sg() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing).

Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")).

Fixes: 9cbee358687e ("ath6kl: add full USB support") Cc: stable@vger.kernel.org # 3.5 Signed-off-by: Johan Hovold johan@kernel.org Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/ath/ath6kl/usb.c | 5 +++++ 1 file changed, 5 insertions(+)

--- a/drivers/net/wireless/ath/ath6kl/usb.c +++ b/drivers/net/wireless/ath/ath6kl/usb.c @@ -340,6 +340,11 @@ static int ath6kl_usb_setup_pipe_resourc le16_to_cpu(endpoint->wMaxPacketSize), endpoint->bInterval); } + + /* Ignore broken descriptors. */ + if (usb_endpoint_maxp(endpoint) == 0) + continue; + urbcount = 0;

pipe_num =

From: Johan Hovold johan@kernel.org

commit 5286132324230168d3fab6ffc16bfd7de85bdfb4 upstream.

USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ.

Fixes: 4db66499df91 ("ath10k: add initial USB support") Cc: stable@vger.kernel.org # 4.14 Cc: Erik Stromdahl erik.stromdahl@gmail.com Signed-off-by: Johan Hovold johan@kernel.org Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20211025120522.6045-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/ath/ath10k/usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/wireless/ath/ath10k/usb.c +++ b/drivers/net/wireless/ath/ath10k/usb.c @@ -536,7 +536,7 @@ static int ath10k_usb_submit_ctrl_in(str req, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, value, index, buf, - size, 2 * HZ); + size, 2000);

if (ret < 0) { ath10k_warn(ar, "Failed to read usb control message: %d\n",

From: Ingmar Klein ingmar_klein@web.de

commit e3f4bd3462f6f796594ecc0dda7144ed2d1e5a26 upstream.

When passing the Atheros QCA6174 through to a virtual machine, the VM hangs at the point where the ath10k driver loads.

Add a quirk to avoid bus resets on this device, which avoids the hang.

[bhelgaas: commit log] Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de Signed-off-by: Ingmar Klein ingmar_klein@web.de Signed-off-by: Bjorn Helgaas bhelgaas@google.com Reviewed-by: Pali Rohár pali@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/pci/quirks.c | 1 + 1 file changed, 1 insertion(+)

--- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -3490,6 +3490,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_A DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003c, quirk_no_bus_reset); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0033, quirk_no_bus_reset); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0034, quirk_no_bus_reset); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003e, quirk_no_bus_reset);

/* * Root port on some Cavium CN8xxx chips do not successfully complete a bus

From: Austin Kim austin.kim@lge.com

commit 32ba540f3c2a7ef61ed5a577ce25069a3d714fc9 upstream.

The evm_fixmode is only configurable by command-line option and it is never modified outside initcalls, so declaring it with __ro_after_init is better.

Signed-off-by: Austin Kim austin.kim@lge.com Cc: stable@vger.kernel.org Signed-off-by: Mimi Zohar zohar@linux.ibm.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- security/integrity/evm/evm_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/security/integrity/evm/evm_main.c +++ b/security/integrity/evm/evm_main.c @@ -59,7 +59,7 @@ static struct xattr_list evm_config_defa

LIST_HEAD(evm_config_xattrnames);

-static int evm_fixmode; +static int evm_fixmode __ro_after_init; static int __init evm_set_fixmode(char *str) { if (strncmp(str, "fix", 3) == 0)

From: Jonas Dreßler verdre@v0yd.nl

commit e5f4eb8223aa740237cd463246a7debcddf4eda1 upstream.

On the 88W8897 PCIe+USB card the firmware randomly crashes after setting the TX ring write pointer. The issue is present in the latest firmware version 15.68.19.p21 of the PCIe+USB card.

Those firmware crashes can be worked around by reading any PCI register of the card after setting that register, so read the PCI_VENDOR_ID register here. The reason this works is probably because we keep the bus from entering an ASPM state for a bit longer, because that's what causes the cards firmware to crash.

This fixes a bug where during RX/TX traffic and with ASPM L1 substates enabled (the specific substates where the issue happens appear to be platform dependent), the firmware crashes and eventually a command timeout appears in the logs.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681 Cc: stable@vger.kernel.org Signed-off-by: Jonas Dreßler verdre@v0yd.nl Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/marvell/mwifiex/pcie.c | 8 ++++++++ 1 file changed, 8 insertions(+)

--- a/drivers/net/wireless/marvell/mwifiex/pcie.c +++ b/drivers/net/wireless/marvell/mwifiex/pcie.c @@ -1330,6 +1330,14 @@ mwifiex_pcie_send_data(struct mwifiex_ad ret = -1; goto done_unmap; } + + /* The firmware (latest version 15.68.19.p21) of the 88W8897 PCIe+USB card + * seems to crash randomly after setting the TX ring write pointer when + * ASPM powersaving is enabled. A workaround seems to be keeping the bus + * busy by reading a random register afterwards. + */ + mwifiex_read_reg(adapter, PCI_VENDOR_ID, &rx_val); + if ((mwifiex_pcie_txbd_not_full(card)) && tx_param->next_pkt_len) { /* have more packets and TxBD still can hold more */

From: Benjamin Li benl@squareup.com

commit d6dbce453b19c64b96f3e927b10230f9a704b504 upstream.

Firmware sends delete_sta_context_ind when it detects the AP has gone away in STA mode. Right now the handler for that indication only handles AP mode; fix it to also handle STA mode.

Cc: stable@vger.kernel.org Signed-off-by: Benjamin Li benl@squareup.com Reviewed-by: Bryan O'Donoghue bryan.odonoghue@linaro.org Reviewed-by: Loic Poulain loic.poulain@linaro.org Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/ath/wcn36xx/smd.c | 44 ++++++++++++++++++++++++--------- 1 file changed, 33 insertions(+), 11 deletions(-)

--- a/drivers/net/wireless/ath/wcn36xx/smd.c +++ b/drivers/net/wireless/ath/wcn36xx/smd.c @@ -2340,30 +2340,52 @@ static int wcn36xx_smd_delete_sta_contex size_t len) { struct wcn36xx_hal_delete_sta_context_ind_msg *rsp = buf; - struct wcn36xx_vif *tmp; + struct wcn36xx_vif *vif_priv; + struct ieee80211_vif *vif; + struct ieee80211_bss_conf *bss_conf; struct ieee80211_sta *sta; + bool found = false;

if (len != sizeof(*rsp)) { wcn36xx_warn("Corrupted delete sta indication\n"); return -EIO; }

- wcn36xx_dbg(WCN36XX_DBG_HAL, "delete station indication %pM index %d\n", - rsp->addr2, rsp->sta_id); + wcn36xx_dbg(WCN36XX_DBG_HAL, + "delete station indication %pM index %d reason %d\n", + rsp->addr2, rsp->sta_id, rsp->reason_code);

- list_for_each_entry(tmp, &wcn->vif_list, list) { + list_for_each_entry(vif_priv, &wcn->vif_list, list) { rcu_read_lock(); - sta = ieee80211_find_sta(wcn36xx_priv_to_vif(tmp), rsp->addr2); - if (sta) - ieee80211_report_low_ack(sta, 0); + vif = wcn36xx_priv_to_vif(vif_priv); + + if (vif->type == NL80211_IFTYPE_STATION) { + /* We could call ieee80211_find_sta too, but checking + * bss_conf is clearer. + */ + bss_conf = &vif->bss_conf; + if (vif_priv->sta_assoc && + !memcmp(bss_conf->bssid, rsp->addr2, ETH_ALEN)) { + found = true; + wcn36xx_dbg(WCN36XX_DBG_HAL, + "connection loss bss_index %d\n", + vif_priv->bss_index); + ieee80211_connection_loss(vif); + } + } else { + sta = ieee80211_find_sta(vif, rsp->addr2); + if (sta) { + found = true; + ieee80211_report_low_ack(sta, 0); + } + } + rcu_read_unlock(); - if (sta) + if (found) return 0; }

- wcn36xx_warn("STA with addr %pM and index %d not found\n", - rsp->addr2, - rsp->sta_id); + wcn36xx_warn("BSS or STA with addr %pM not found\n", rsp->addr2); return -ENOENT; }

From: Martin Fuzzey martin.fuzzey@flowbird.group

commit 99ac6018821253ec67f466086afb63fc18ea48e2 upstream.

My previous patch checked if encryption should be enabled by directly checking info->control.hw_key (like the downstream driver). However that missed that the control and driver_info members of struct ieee80211_tx_info are union fields.

Due to this when rsi_core_xmit() updates fields in "tx_params" (driver_info) it can overwrite the control.hw_key, causing the result of the later test to be incorrect.

With the current structure layout the first byte of control.hw_key is overlayed with the vap_id so, since we only test if control.hw_key is NULL / non NULL, a non zero vap_id will incorrectly enable encryption.

In basic STA and AP modes the vap_id is always zero so it works but in P2P client mode a second VIF is created causing vap_id to be non zero and hence encryption to be enabled before keys have been set.

Fix this by extracting the key presence flag to a new field in the driver private tx_params structure and populating it first.

Fixes: 314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL") Signed-off-by: Martin Fuzzey martin.fuzzey@flowbird.group CC: stable@vger.kernel.org Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@fl... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/rsi/rsi_91x_core.c | 2 ++ drivers/net/wireless/rsi/rsi_91x_hal.c | 2 +- drivers/net/wireless/rsi/rsi_main.h | 1 + 3 files changed, 4 insertions(+), 1 deletion(-)

--- a/drivers/net/wireless/rsi/rsi_91x_core.c +++ b/drivers/net/wireless/rsi/rsi_91x_core.c @@ -400,6 +400,8 @@ void rsi_core_xmit(struct rsi_common *co

info = IEEE80211_SKB_CB(skb); tx_params = (struct skb_info *)info->driver_data; + /* info->driver_data and info->control part of union so make copy */ + tx_params->have_key = !!info->control.hw_key; wh = (struct ieee80211_hdr *)&skb->data[0]; tx_params->sta_id = 0;

--- a/drivers/net/wireless/rsi/rsi_91x_hal.c +++ b/drivers/net/wireless/rsi/rsi_91x_hal.c @@ -193,7 +193,7 @@ int rsi_prepare_data_desc(struct rsi_com wh->frame_control |= cpu_to_le16(RSI_SET_PS_ENABLE);

if ((!(info->flags & IEEE80211_TX_INTFL_DONT_ENCRYPT)) && - info->control.hw_key) { + tx_params->have_key) { if (rsi_is_cipher_wep(common)) ieee80211_size += 4; else --- a/drivers/net/wireless/rsi/rsi_main.h +++ b/drivers/net/wireless/rsi/rsi_main.h @@ -135,6 +135,7 @@ struct skb_info { u8 internal_hdr_size; struct ieee80211_vif *vif; u8 vap_id; + bool have_key; };

enum edca_queue {

From: Marek Vasut marex@denx.de

commit 31f97cf9f0c31143a2a6fcc89c4a1286ce20157e upstream.

The module parameters are missing dev_oper_mode 12, BT classic alone, add it. Moreover, the parameters encode newlines, which ends up being printed malformed e.g. by modinfo, so fix that too.

However, the module parameter string is duplicated in both USB and SDIO modules and the dev_oper_mode mode enumeration in those module parameters is a duplicate of macros used by the driver. Furthermore, the enumeration is confusing.

So, deduplicate the module parameter string and use __stringify() to encode the correct mode enumeration values into the module parameter string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with 'BT classic alone' to clarify what those modes really mean.

Fixes: 898b255339310 ("rsi: add module parameter operating mode") Signed-off-by: Marek Vasut marex@denx.de Cc: Amitkumar Karwar amit.karwar@redpinesignals.com Cc: Angus Ainslie angus@akkea.ca Cc: David S. Miller davem@davemloft.net Cc: Jakub Kicinski kuba@kernel.org Cc: Kalle Valo kvalo@codeaurora.org Cc: Karun Eagalapati karun256@gmail.com Cc: Martin Fuzzey martin.fuzzey@flowbird.group Cc: Martin Kepplinger martink@posteo.de Cc: Prameela Rani Garnepudi prameela.j04cs@gmail.com Cc: Sebastian Krzyszkowiak sebastian.krzyszkowiak@puri.sm Cc: Siva Rebbagondla siva8118@gmail.com Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org # 4.17+ Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/net/wireless/rsi/rsi_91x_sdio.c | 5 +---- drivers/net/wireless/rsi/rsi_91x_usb.c | 5 +---- drivers/net/wireless/rsi/rsi_hal.h | 11 +++++++++++ 3 files changed, 13 insertions(+), 8 deletions(-)

--- a/drivers/net/wireless/rsi/rsi_91x_sdio.c +++ b/drivers/net/wireless/rsi/rsi_91x_sdio.c @@ -24,10 +24,7 @@ /* Default operating mode is wlan STA + BT */ static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; module_param(dev_oper_mode, ushort, 0444); -MODULE_PARM_DESC(dev_oper_mode, - "1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n" - "9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n" - "6[AP + BT classic], 14[AP + BT classic + BT LE]"); +MODULE_PARM_DESC(dev_oper_mode, DEV_OPMODE_PARAM_DESC);

/** * rsi_sdio_set_cmd52_arg() - This function prepares cmd 52 read/write arg. --- a/drivers/net/wireless/rsi/rsi_91x_usb.c +++ b/drivers/net/wireless/rsi/rsi_91x_usb.c @@ -25,10 +25,7 @@ /* Default operating mode is wlan STA + BT */ static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; module_param(dev_oper_mode, ushort, 0444); -MODULE_PARM_DESC(dev_oper_mode, - "1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n" - "9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n" - "6[AP + BT classic], 14[AP + BT classic + BT LE]"); +MODULE_PARM_DESC(dev_oper_mode, DEV_OPMODE_PARAM_DESC);

static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t flags);

--- a/drivers/net/wireless/rsi/rsi_hal.h +++ b/drivers/net/wireless/rsi/rsi_hal.h @@ -28,6 +28,17 @@ #define DEV_OPMODE_AP_BT 6 #define DEV_OPMODE_AP_BT_DUAL 14

+#define DEV_OPMODE_PARAM_DESC \ + __stringify(DEV_OPMODE_WIFI_ALONE) "[Wi-Fi alone], " \ + __stringify(DEV_OPMODE_BT_ALONE) "[BT classic alone], " \ + __stringify(DEV_OPMODE_BT_LE_ALONE) "[BT LE alone], " \ + __stringify(DEV_OPMODE_BT_DUAL) "[BT classic + BT LE alone], " \ + __stringify(DEV_OPMODE_STA_BT) "[Wi-Fi STA + BT classic], " \ + __stringify(DEV_OPMODE_STA_BT_LE) "[Wi-Fi STA + BT LE], " \ + __stringify(DEV_OPMODE_STA_BT_DUAL) "[Wi-Fi STA + BT classic + BT LE], " \ + __stringify(DEV_OPMODE_AP_BT) "[Wi-Fi AP + BT classic], " \ + __stringify(DEV_OPMODE_AP_BT_DUAL) "[Wi-Fi AP + BT classic + BT LE]" + #define FLASH_WRITE_CHUNK_SIZE (4 * 1024) #define FLASH_SECTOR_SIZE (4 * 1024)

From: Eric W. Biederman ebiederm@xmission.com

commit 7d613f9f72ec8f90ddefcae038fdae5adb8404b3 upstream.

The existence of sigkill_pending is a little silly as it is functionally a duplicate of fatal_signal_pending that is used in exactly one place.

Checking for pending fatal signals and returning early in ptrace_stop is actively harmful. It casues the ptrace_stop called by ptrace_signal to return early before setting current->exit_code. Later when ptrace_signal reads the signal number from current->exit_code is undefined, making it unpredictable what will happen.

Instead rely on the fact that schedule will not sleep if there is a pending signal that can awaken a task.

Removing the explict sigkill_pending test fixes fixes ptrace_signal when ptrace_stop does not stop because current->exit_code is always set to to signr.

Cc: stable@vger.kernel.org Fixes: 3d749b9e676b ("ptrace: simplify ptrace_stop()->sigkill_pending() path") Fixes: 1a669c2f16d4 ("Add arch_ptrace_stop") Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133 Reviewed-by: Kees Cook keescook@chromium.org Signed-off-by: "Eric W. Biederman" ebiederm@xmission.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- kernel/signal.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)

--- a/kernel/signal.c +++ b/kernel/signal.c @@ -2003,15 +2003,6 @@ static inline bool may_ptrace_stop(void) return true; }

-/* - * Return non-zero if there is a SIGKILL that should be waking us up. - * Called with the siglock held. - */ -static bool sigkill_pending(struct task_struct *tsk) -{ - return sigismember(&tsk->pending.signal, SIGKILL) || - sigismember(&tsk->signal->shared_pending.signal, SIGKILL); -}

/* * This must be called with current->sighand->siglock held. @@ -2038,17 +2029,16 @@ static void ptrace_stop(int exit_code, i * calling arch_ptrace_stop, so we must release it now. * To preserve proper semantics, we must do this before * any signal bookkeeping like checking group_stop_count. - * Meanwhile, a SIGKILL could come in before we retake the - * siglock. That must prevent us from sleeping in TASK_TRACED. - * So after regaining the lock, we must check for SIGKILL. */ spin_unlock_irq(&current->sighand->siglock); arch_ptrace_stop(exit_code, info); spin_lock_irq(&current->sighand->siglock); - if (sigkill_pending(current)) - return; }

+ /* + * schedule() will not sleep if there is a pending signal that + * can awaken the task. + */ set_special_state(TASK_TRACED);

/*

From: Sebastian Krzyszkowiak sebastian.krzyszkowiak@puri.sm

commit e660dbb68c6b3f7b9eb8b9775846a44f9798b719 upstream.

max17042_set_soc_threshold gets called with offset set to 1, which means that minimum threshold value would underflow once SOC got down to 0, causing invalid alerts from the gauge.

Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC") Cc: stable@vger.kernel.org Signed-off-by: Sebastian Krzyszkowiak sebastian.krzyszkowiak@puri.sm Reviewed-by: Krzysztof Kozlowski krzysztof.kozlowski@canonical.com Signed-off-by: Sebastian Reichel sebastian.reichel@collabora.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/power/supply/max17042_battery.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/power/supply/max17042_battery.c +++ b/drivers/power/supply/max17042_battery.c @@ -848,7 +848,8 @@ static void max17042_set_soc_threshold(s regmap_read(map, MAX17042_RepSOC, &soc); soc >>= 8; soc_tr = (soc + off) << 8; - soc_tr |= (soc - off); + if (off < soc) + soc_tr |= soc - off; regmap_write(map, MAX17042_SALRT_Th, soc_tr); }

From: Xiaoming Ni nixiaoming@huawei.com

commit 3c2172c1c47b4079c29f0e6637d764a99355ebcd upstream.

When the field described in mpc85xx_smp_guts_ids[] is not configured in dtb, the mpc85xx_setup_pmc() does not assign a value to the "guts" variable. As a result, the oops is triggered when mpc85xx_freeze_time_base() is executed.

Fixes: 56f1ba280719 ("powerpc/mpc85xx: refactor the PM operations") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Xiaoming Ni nixiaoming@huawei.com Signed-off-by: Michael Ellerman mpe@ellerman.id.au Link: https://lore.kernel.org/r/20210929033646.39630-2-nixiaoming@huawei.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- arch/powerpc/platforms/85xx/mpc85xx_pm_ops.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)

--- a/arch/powerpc/platforms/85xx/mpc85xx_pm_ops.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_pm_ops.c @@ -98,9 +98,8 @@ int __init mpc85xx_setup_pmc(void) pr_err("Could not map guts node address\n"); return -ENOMEM; } + qoriq_pm_ops = &mpc85xx_pm_ops; }

- qoriq_pm_ops = &mpc85xx_pm_ops; - return 0; }

From: Takashi Iwai tiwai@suse.de

commit 411cef6adfb38a5bb6bd9af3941b28198e7fb680 upstream.

The OSS mixer can reassign the mapping slots dynamically via proc file. Although the addition and deletion of those slots are protected by mixer->reg_mutex, the access to slots aren't, hence this may cause UAF when the slots in use are deleted concurrently.

This patch applies the mixer->reg_mutex in all appropriate code paths (i.e. the ioctl functions) that may access slots.

Reported-by: syzbot+9988f17cf72a1045a189@syzkaller.appspotmail.com Reviewed-by: Jaroslav Kysela perex@perex.cz Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/00000000000036adc005ceca9175@google.com Link: https://lore.kernel.org/r/20211020164846.922-1-tiwai@suse.de Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- sound/core/oss/mixer_oss.c | 43 +++++++++++++++++++++++++++++++++---------- 1 file changed, 33 insertions(+), 10 deletions(-)

--- a/sound/core/oss/mixer_oss.c +++ b/sound/core/oss/mixer_oss.c @@ -145,11 +145,13 @@ static int snd_mixer_oss_devmask(struct

if (mixer == NULL) return -EIO; + mutex_lock(&mixer->reg_mutex); for (chn = 0; chn < 31; chn++) { pslot = &mixer->slots[chn]; if (pslot->put_volume || pslot->put_recsrc) result |= 1 << chn; } + mutex_unlock(&mixer->reg_mutex); return result; }

@@ -161,11 +163,13 @@ static int snd_mixer_oss_stereodevs(stru

if (mixer == NULL) return -EIO; + mutex_lock(&mixer->reg_mutex); for (chn = 0; chn < 31; chn++) { pslot = &mixer->slots[chn]; if (pslot->put_volume && pslot->stereo) result |= 1 << chn; } + mutex_unlock(&mixer->reg_mutex); return result; }

@@ -176,6 +180,7 @@ static int snd_mixer_oss_recmask(struct

if (mixer == NULL) return -EIO; + mutex_lock(&mixer->reg_mutex); if (mixer->put_recsrc && mixer->get_recsrc) { /* exclusive */ result = mixer->mask_recsrc; } else { @@ -187,6 +192,7 @@ static int snd_mixer_oss_recmask(struct result |= 1 << chn; } } + mutex_unlock(&mixer->reg_mutex); return result; }

@@ -197,11 +203,12 @@ static int snd_mixer_oss_get_recsrc(stru

if (mixer == NULL) return -EIO; + mutex_lock(&mixer->reg_mutex); if (mixer->put_recsrc && mixer->get_recsrc) { /* exclusive */ - int err; unsigned int index; - if ((err = mixer->get_recsrc(fmixer, &index)) < 0) - return err; + result = mixer->get_recsrc(fmixer, &index); + if (result < 0) + goto unlock; result = 1 << index; } else { struct snd_mixer_oss_slot *pslot; @@ -216,7 +223,10 @@ static int snd_mixer_oss_get_recsrc(stru } } } - return mixer->oss_recsrc = result; + mixer->oss_recsrc = result; + unlock: + mutex_unlock(&mixer->reg_mutex); + return result; }

static int snd_mixer_oss_set_recsrc(struct snd_mixer_oss_file *fmixer, int recsrc) @@ -229,6 +239,7 @@ static int snd_mixer_oss_set_recsrc(stru

if (mixer == NULL) return -EIO; + mutex_lock(&mixer->reg_mutex); if (mixer->get_recsrc && mixer->put_recsrc) { /* exclusive input */ if (recsrc & ~mixer->oss_recsrc) recsrc &= ~mixer->oss_recsrc; @@ -254,6 +265,7 @@ static int snd_mixer_oss_set_recsrc(stru } } } + mutex_unlock(&mixer->reg_mutex); return result; }

@@ -265,6 +277,7 @@ static int snd_mixer_oss_get_volume(stru

if (mixer == NULL || slot > 30) return -EIO; + mutex_lock(&mixer->reg_mutex); pslot = &mixer->slots[slot]; left = pslot->volume[0]; right = pslot->volume[1]; @@ -272,15 +285,21 @@ static int snd_mixer_oss_get_volume(stru result = pslot->get_volume(fmixer, pslot, &left, &right); if (!pslot->stereo) right = left; - if (snd_BUG_ON(left < 0 || left > 100)) - return -EIO; - if (snd_BUG_ON(right < 0 || right > 100)) - return -EIO; + if (snd_BUG_ON(left < 0 || left > 100)) { + result = -EIO; + goto unlock; + } + if (snd_BUG_ON(right < 0 || right > 100)) { + result = -EIO; + goto unlock; + } if (result >= 0) { pslot->volume[0] = left; pslot->volume[1] = right; result = (left & 0xff) | ((right & 0xff) << 8); } + unlock: + mutex_unlock(&mixer->reg_mutex); return result; }

@@ -293,6 +312,7 @@ static int snd_mixer_oss_set_volume(stru

if (mixer == NULL || slot > 30) return -EIO; + mutex_lock(&mixer->reg_mutex); pslot = &mixer->slots[slot]; if (left > 100) left = 100; @@ -303,10 +323,13 @@ static int snd_mixer_oss_set_volume(stru if (pslot->put_volume) result = pslot->put_volume(fmixer, pslot, left, right); if (result < 0) - return result; + goto unlock; pslot->volume[0] = left; pslot->volume[1] = right; - return (left & 0xff) | ((right & 0xff) << 8); + result = (left & 0xff) | ((right & 0xff) << 8); + unlock: + mutex_lock(&mixer->reg_mutex); + return result; }

static int snd_mixer_oss_ioctl1(struct snd_mixer_oss_file *fmixer, unsigned int cmd, unsigned long arg)

From: Juergen Gross jgross@suse.com

commit 40fdea0284bb20814399da0484a658a96c735d90 upstream.

When running as PVH or HVM guest with actual memory < max memory the hypervisor is using "populate on demand" in order to allow the guest to balloon down from its maximum memory size. For this to work correctly the guest must not touch more memory pages than its target memory size as otherwise the PoD cache will be exhausted and the guest is crashed as a result of that.

In extreme cases ballooning down might not be finished today before the init process is started, which can consume lots of memory.

In order to avoid random boot crashes in such cases, add a late init call to wait for ballooning down having finished for PVH/HVM guests.

Warn on console if initial ballooning fails, panic() after stalling for more than 3 minutes per default. Add a module parameter for changing this timeout.

[boris: replaced pr_info() with pr_notice()]

Cc: stable@vger.kernel.org Reported-by: Marek Marczykowski-Górecki marmarek@invisiblethingslab.com Signed-off-by: Juergen Gross jgross@suse.com Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com Reviewed-by: Boris Ostrovsky boris.ostrovsky@oracle.com Signed-off-by: Boris Ostrovsky boris.ostrovsky@oracle.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- Documentation/admin-guide/kernel-parameters.txt | 7 + drivers/xen/balloon.c | 86 +++++++++++++++++------- 2 files changed, 70 insertions(+), 23 deletions(-)

--- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -5284,6 +5284,13 @@ with /sys/devices/system/xen_memory/xen_memory0/scrub_pages. Default value controlled with CONFIG_XEN_SCRUB_PAGES_DEFAULT.

+ xen.balloon_boot_timeout= [XEN] + The time (in seconds) to wait before giving up to boot + in case initial ballooning fails to free enough memory. + Applies only when running as HVM or PVH guest and + started with less memory configured than allowed at + max. Default is 180. + xen.event_eoi_delay= [XEN] How long to delay EOI handling in case of event storms (jiffies). Default is 10. --- a/drivers/xen/balloon.c +++ b/drivers/xen/balloon.c @@ -58,6 +58,7 @@ #include <linux/percpu-defs.h> #include <linux/slab.h> #include <linux/sysctl.h> +#include <linux/moduleparam.h>

#include <asm/page.h> #include <asm/pgalloc.h> @@ -75,6 +76,12 @@ #include <xen/page.h> #include <xen/mem-reservation.h>

+#undef MODULE_PARAM_PREFIX +#define MODULE_PARAM_PREFIX "xen." + +static uint __read_mostly balloon_boot_timeout = 180; +module_param(balloon_boot_timeout, uint, 0444); + static int xen_hotplug_unpopulated;

#ifdef CONFIG_XEN_BALLOON_MEMORY_HOTPLUG @@ -130,12 +137,12 @@ static struct ctl_table xen_root[] = { * BP_ECANCELED: error, balloon operation canceled. */

-enum bp_state { +static enum bp_state { BP_DONE, BP_WAIT, BP_EAGAIN, BP_ECANCELED -}; +} balloon_state = BP_DONE;

/* Main waiting point for xen-balloon thread. */ static DECLARE_WAIT_QUEUE_HEAD(balloon_thread_wq); @@ -206,18 +213,15 @@ static struct page *balloon_next_page(st return list_entry(next, struct page, lru); }

-static enum bp_state update_schedule(enum bp_state state) +static void update_schedule(void) { - if (state == BP_WAIT) - return BP_WAIT; - - if (state == BP_ECANCELED) - return BP_ECANCELED; + if (balloon_state == BP_WAIT || balloon_state == BP_ECANCELED) + return;

- if (state == BP_DONE) { + if (balloon_state == BP_DONE) { balloon_stats.schedule_delay = 1; balloon_stats.retry_count = 1; - return BP_DONE; + return; }

++balloon_stats.retry_count; @@ -226,7 +230,8 @@ static enum bp_state update_schedule(enu balloon_stats.retry_count > balloon_stats.max_retry_count) { balloon_stats.schedule_delay = 1; balloon_stats.retry_count = 1; - return BP_ECANCELED; + balloon_state = BP_ECANCELED; + return; }

balloon_stats.schedule_delay <<= 1; @@ -234,7 +239,7 @@ static enum bp_state update_schedule(enu if (balloon_stats.schedule_delay > balloon_stats.max_schedule_delay) balloon_stats.schedule_delay = balloon_stats.max_schedule_delay;

- return BP_EAGAIN; + balloon_state = BP_EAGAIN; }

#ifdef CONFIG_XEN_BALLOON_MEMORY_HOTPLUG @@ -511,9 +516,9 @@ static enum bp_state decrease_reservatio * Stop waiting if either state is BP_DONE and ballooning action is * needed, or if the credit has changed while state is not BP_DONE. */ -static bool balloon_thread_cond(enum bp_state state, long credit) +static bool balloon_thread_cond(long credit) { - if (state == BP_DONE) + if (balloon_state == BP_DONE) credit = 0;

return current_credit() != credit || kthread_should_stop(); @@ -527,13 +532,12 @@ static bool balloon_thread_cond(enum bp_ */ static int balloon_thread(void *unused) { - enum bp_state state = BP_DONE; long credit; unsigned long timeout;

set_freezable(); for (;;) { - switch (state) { + switch (balloon_state) { case BP_DONE: case BP_ECANCELED: timeout = 3600 * HZ; @@ -549,7 +553,7 @@ static int balloon_thread(void *unused) credit = current_credit();

wait_event_freezable_timeout(balloon_thread_wq, - balloon_thread_cond(state, credit), timeout); + balloon_thread_cond(credit), timeout);

if (kthread_should_stop()) return 0; @@ -560,22 +564,23 @@ static int balloon_thread(void *unused)

if (credit > 0) { if (balloon_is_inflated()) - state = increase_reservation(credit); + balloon_state = increase_reservation(credit); else - state = reserve_additional_memory(); + balloon_state = reserve_additional_memory(); }

if (credit < 0) { long n_pages;

n_pages = min(-credit, si_mem_available()); - state = decrease_reservation(n_pages, GFP_BALLOON); - if (state == BP_DONE && n_pages != -credit && + balloon_state = decrease_reservation(n_pages, + GFP_BALLOON); + if (balloon_state == BP_DONE && n_pages != -credit && n_pages < totalreserve_pages) - state = BP_EAGAIN; + balloon_state = BP_EAGAIN; }

- state = update_schedule(state); + update_schedule();

mutex_unlock(&balloon_mutex);

@@ -784,3 +789,38 @@ static int __init balloon_init(void) return 0; } subsys_initcall(balloon_init); + +static int __init balloon_wait_finish(void) +{ + long credit, last_credit = 0; + unsigned long last_changed = 0; + + if (!xen_domain()) + return -ENODEV; + + /* PV guests don't need to wait. */ + if (xen_pv_domain() || !current_credit()) + return 0; + + pr_notice("Waiting for initial ballooning down having finished.\n"); + + while ((credit = current_credit()) < 0) { + if (credit != last_credit) { + last_changed = jiffies; + last_credit = credit; + } + if (balloon_state == BP_ECANCELED) { + pr_warn_once("Initial ballooning failed, %ld pages need to be freed.\n", + -credit); + if (jiffies - last_changed >= HZ * balloon_boot_timeout) + panic("Initial ballooning failed!\n"); + } + + schedule_timeout_interruptible(HZ / 10); + } + + pr_notice("Initial ballooning down finished.\n"); + + return 0; +} +late_initcall_sync(balloon_wait_finish);

From: Pali Rohár pali@kernel.org

commit 1fb95d7d3c7a926b002fe8a6bd27a1cb428b46dc upstream.

There are lot of undocumented interrupt bits. To prevent unwanted spurious interrupts, fix all *_ALL_MASK macros to define all interrupt bits, so that driver can properly mask all interrupts, including those which are undocumented.

Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár pali@kernel.org Signed-off-by: Marek Behún kabel@kernel.org Signed-off-by: Lorenzo Pieralisi lorenzo.pieralisi@arm.com Reviewed-by: Marek Behún kabel@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/pci/controller/pci-aardvark.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

--- a/drivers/pci/controller/pci-aardvark.c +++ b/drivers/pci/controller/pci-aardvark.c @@ -99,13 +99,13 @@ #define PCIE_ISR0_MSI_INT_PENDING BIT(24) #define PCIE_ISR0_INTX_ASSERT(val) BIT(16 + (val)) #define PCIE_ISR0_INTX_DEASSERT(val) BIT(20 + (val)) -#define PCIE_ISR0_ALL_MASK GENMASK(26, 0) +#define PCIE_ISR0_ALL_MASK GENMASK(31, 0) #define PCIE_ISR1_REG (CONTROL_BASE_ADDR + 0x48) #define PCIE_ISR1_MASK_REG (CONTROL_BASE_ADDR + 0x4C) #define PCIE_ISR1_POWER_STATE_CHANGE BIT(4) #define PCIE_ISR1_FLUSH BIT(5) #define PCIE_ISR1_INTX_ASSERT(val) BIT(8 + (val)) -#define PCIE_ISR1_ALL_MASK GENMASK(11, 4) +#define PCIE_ISR1_ALL_MASK GENMASK(31, 0) #define PCIE_MSI_ADDR_LOW_REG (CONTROL_BASE_ADDR + 0x50) #define PCIE_MSI_ADDR_HIGH_REG (CONTROL_BASE_ADDR + 0x54) #define PCIE_MSI_STATUS_REG (CONTROL_BASE_ADDR + 0x58) @@ -150,7 +150,7 @@ #define PCIE_IRQ_MSI_INT2_DET BIT(21) #define PCIE_IRQ_RC_DBELL_DET BIT(22) #define PCIE_IRQ_EP_STATUS BIT(23) -#define PCIE_IRQ_ALL_MASK 0xfff0fb +#define PCIE_IRQ_ALL_MASK GENMASK(31, 0) #define PCIE_IRQ_ENABLE_INTS_MASK PCIE_IRQ_CORE_INT

/* Transaction types */

From: Marek Behún kabel@kernel.org

commit 95997723b6402cd6c53e0f9e7ac640ec64eaaff8 upstream.

The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower 8 bits. Fix reading content of this register and add a comment describing the access to this register.

Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár pali@kernel.org Signed-off-by: Marek Behún kabel@kernel.org Signed-off-by: Lorenzo Pieralisi lorenzo.pieralisi@arm.com Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/pci/controller/pci-aardvark.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)

--- a/drivers/pci/controller/pci-aardvark.c +++ b/drivers/pci/controller/pci-aardvark.c @@ -111,6 +111,7 @@ #define PCIE_MSI_STATUS_REG (CONTROL_BASE_ADDR + 0x58) #define PCIE_MSI_MASK_REG (CONTROL_BASE_ADDR + 0x5C) #define PCIE_MSI_PAYLOAD_REG (CONTROL_BASE_ADDR + 0x9C) +#define PCIE_MSI_DATA_MASK GENMASK(15, 0)

/* LMI registers base address and register offsets */ #define LMI_BASE_ADDR 0x6000 @@ -805,8 +806,12 @@ static void advk_pcie_handle_msi(struct if (!(BIT(msi_idx) & msi_status)) continue;

+ /* + * msi_idx contains bits [4:0] of the msi_data and msi_data + * contains 16bit MSI interrupt number + */ advk_writel(pcie, BIT(msi_idx), PCIE_MSI_STATUS_REG); - msi_data = advk_readl(pcie, PCIE_MSI_PAYLOAD_REG) & 0xFF; + msi_data = advk_readl(pcie, PCIE_MSI_PAYLOAD_REG) & PCIE_MSI_DATA_MASK; generic_handle_irq(msi_data); }

From: Zhang Yi yi.zhang@huawei.com

commit d0e36a62bd4c60c09acc40e06ba4831a4d0bc75b upstream.

Fix the error path in free_dqentry(), pass out the error number if the block to free is not correct.

Fixes: 1ccd14b9c271 ("quota: Split off quota tree handling into a separate file") Link: https://lore.kernel.org/r/20211008093821.1001186-3-yi.zhang@huawei.com Signed-off-by: Zhang Yi yi.zhang@huawei.com Cc: stable@kernel.org Signed-off-by: Jan Kara jack@suse.cz Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- fs/quota/quota_tree.c | 1 + 1 file changed, 1 insertion(+)

--- a/fs/quota/quota_tree.c +++ b/fs/quota/quota_tree.c @@ -422,6 +422,7 @@ static int free_dqentry(struct qtree_mem quota_error(dquot->dq_sb, "Quota structure has offset to " "other block (%u) than it should (%u)", blk, (uint)(dquot->dq_off >> info->dqi_blocksize_bits)); + ret = -EIO; goto out_buf; } ret = read_blk(info, blk, buf);

From: Pekka Korpinen pekka.korpinen@iki.fi

commit 558df982d4ead9cac628153d0d7b60feae05ddc8 upstream.

On success i2c_master_send() returns the number of bytes written. The call from iio_write_channel_info(), however, expects the return value to be zero on success.

This bug causes incorrect consumption of the sysfs buffer in iio_write_channel_info(). When writing more than two characters to out_voltage0_raw, the ad5446 write handler is called multiple times causing unexpected behavior.

Fixes: 3ec36a2cf0d5 ("iio:ad5446: Add support for I2C based DACs") Signed-off-by: Pekka Korpinen pekka.korpinen@iki.fi Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron Jonathan.Cameron@huawei.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/iio/dac/ad5446.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)

--- a/drivers/iio/dac/ad5446.c +++ b/drivers/iio/dac/ad5446.c @@ -528,8 +528,15 @@ static int ad5622_write(struct ad5446_st { struct i2c_client *client = to_i2c_client(st->dev); __be16 data = cpu_to_be16(val); + int ret;

- return i2c_master_send(client, (char *)&data, sizeof(data)); + ret = i2c_master_send(client, (char *)&data, sizeof(data)); + if (ret < 0) + return ret; + if (ret != sizeof(data)) + return -EIO; + + return 0; }

/**

From: Johan Hovold johan@kernel.org

commit 79a4479a17b83310deb0b1a2a274fe5be12d2318 upstream.

USB control-message timeouts are specified in milliseconds and should specifically not vary with CONFIG_HZ.

Use the common control-message timeout define for the five-second timeout and drop the driver-specific one.

Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.") Cc: stable@vger.kernel.org # 2.6.21 Signed-off-by: Johan Hovold johan@kernel.org Link: https://lore.kernel.org/r/20211025115159.4954-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org --- drivers/usb/misc/iowarrior.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)

--- a/drivers/usb/misc/iowarrior.c +++ b/drivers/usb/misc/iowarrior.c @@ -103,10 +103,6 @@ struct iowarrior { /* globals */ /*--------------*/

-/* - * USB spec identifies 5 second timeouts. - */ -#define GET_TIMEOUT 5 #define USB_REQ_GET_REPORT 0x01 //#if 0 static int usb_get_report(struct usb_device *dev, @@ -118,7 +114,7 @@ static int usb_get_report(struct usb_dev USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE, (type << 8) + id, inter->desc.bInterfaceNumber, buf, size, - GET_TIMEOUT*HZ); + USB_CTRL_GET_TIMEOUT); } //#endif

@@ -133,7 +129,7 @@ static int usb_set_report(struct usb_int USB_TYPE_CLASS | USB_RECIP_INTERFACE, (type << 8) + id, intf->cur_altsetting->desc.bInterfaceNumber, buf, - size, HZ); + size, 1000); }

/*---------------------*/

From: Takashi Iwai tiwai@suse.de

[ Upstream commit 99c23da0eed4fd20cae8243f2b51e10e66aa0951 ]

The sco_send_frame() also takes lock_sock() during memcpy_from_msg() call that may be endlessly blocked by a task with userfaultd technique, and this will result in a hung task watchdog trigger.

Just like the similar fix for hci_sock_sendmsg() in commit 92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves the memcpy_from_msg() out of lock_sock() for addressing the hang.

This should be the last piece for fixing CVE-2021-3640 after a few already queued fixes.

Signed-off-by: Takashi Iwai tiwai@suse.de Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/bluetooth/sco.c | 24 ++++++++++++++++-------- 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/net/bluetooth/sco.c b/net/bluetooth/sco.c index 007a01b08dbe9..d052b454dc4e1 100644 --- a/net/bluetooth/sco.c +++ b/net/bluetooth/sco.c @@ -280,7 +280,8 @@ static int sco_connect(struct hci_dev *hdev, struct sock *sk) return err; }

-static int sco_send_frame(struct sock *sk, struct msghdr *msg, int len) +static int sco_send_frame(struct sock *sk, void *buf, int len, + unsigned int msg_flags) { struct sco_conn *conn = sco_pi(sk)->conn; struct sk_buff *skb; @@ -292,15 +293,11 @@ static int sco_send_frame(struct sock *sk, struct msghdr *msg, int len)

BT_DBG("sk %p len %d", sk, len);

- skb = bt_skb_send_alloc(sk, len, msg->msg_flags & MSG_DONTWAIT, &err); + skb = bt_skb_send_alloc(sk, len, msg_flags & MSG_DONTWAIT, &err); if (!skb) return err;

- if (memcpy_from_msg(skb_put(skb, len), msg, len)) { - kfree_skb(skb); - return -EFAULT; - } - + memcpy(skb_put(skb, len), buf, len); hci_send_sco(conn->hcon, skb);

return len; @@ -714,6 +711,7 @@ static int sco_sock_sendmsg(struct socket *sock, struct msghdr *msg, size_t len) { struct sock *sk = sock->sk; + void *buf; int err;

BT_DBG("sock %p, sk %p", sock, sk); @@ -725,14 +723,24 @@ static int sco_sock_sendmsg(struct socket *sock, struct msghdr *msg, if (msg->msg_flags & MSG_OOB) return -EOPNOTSUPP;

+ buf = kmalloc(len, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + if (memcpy_from_msg(buf, msg, len)) { + kfree(buf); + return -EFAULT; + } + lock_sock(sk);

if (sk->sk_state == BT_CONNECTED) - err = sco_send_frame(sk, msg, len); + err = sco_send_frame(sk, buf, len, msg->msg_flags); else err = -ENOTCONN;

release_sock(sk); + kfree(buf); return err; }

From: Barnabás Pőcze pobrn@protonmail.com

[ Upstream commit 1975718c488a39128f1f515b23ae61a5a214cc3d ]

Previously, `__query_block()` would fail if the second WCxx method call failed. However, the WQxx method might have succeeded, and potentially allocated memory for the result. Instead of throwing away the result and potentially leaking memory, ignore the result of the second WCxx call.

Signed-off-by: Barnabás Pőcze pobrn@protonmail.com Link: https://lore.kernel.org/r/20210904175450.156801-25-pobrn@protonmail.com Reviewed-by: Hans de Goede hdegoede@redhat.com Signed-off-by: Hans de Goede hdegoede@redhat.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/platform/x86/wmi.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/platform/x86/wmi.c b/drivers/platform/x86/wmi.c index 35cdc3998eb59..387358af685c5 100644 --- a/drivers/platform/x86/wmi.c +++ b/drivers/platform/x86/wmi.c @@ -350,7 +350,14 @@ static acpi_status __query_block(struct wmi_block *wblock, u8 instance, * the WQxx method failed - we should disable collection anyway. */ if ((block->flags & ACPI_WMI_EXPENSIVE) && ACPI_SUCCESS(wc_status)) { - status = acpi_execute_simple_method(handle, wc_method, 0); + /* + * Ignore whether this WCxx call succeeds or not since + * the previously executed WQxx method call might have + * succeeded, and returning the failing status code + * of this call would throw away the result of the WQxx + * call, potentially leaking memory. + */ + acpi_execute_simple_method(handle, wc_method, 0); }

return status;

From: Aleksander Jan Bajkowski olek2@wp.pl

[ Upstream commit 5ca9ce2ba4d5884cd94d1a856c675ab1242cd242 ]

Different SoCs have a different number of channels, e.g .: * amazon-se has 10 channels, * danube+ar9 have 20 channels, * vr9 has 28 channels, * ar10 has 24 channels.

We can read the ID register and, depending on the reported number of channels, reset the appropriate number of channels.

Signed-off-by: Aleksander Jan Bajkowski olek2@wp.pl Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/mips/lantiq/xway/dma.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/arch/mips/lantiq/xway/dma.c b/arch/mips/lantiq/xway/dma.c index 45a622b72cd13..efee1c538a518 100644 --- a/arch/mips/lantiq/xway/dma.c +++ b/arch/mips/lantiq/xway/dma.c @@ -41,6 +41,7 @@ #define LTQ_DMA_PCTRL 0x44 #define LTQ_DMA_IRNEN 0xf4

+#define DMA_ID_CHNR GENMASK(26, 20) /* channel number */ #define DMA_DESCPT BIT(3) /* descriptor complete irq */ #define DMA_TX BIT(8) /* TX channel direction */ #define DMA_CHAN_ON BIT(0) /* channel on / off bit */ @@ -51,7 +52,6 @@ #define DMA_POLL BIT(31) /* turn on channel polling */ #define DMA_CLK_DIV4 BIT(6) /* polling clock divider */ #define DMA_2W_BURST BIT(1) /* 2 word burst length */ -#define DMA_MAX_CHANNEL 20 /* the soc has 20 channels */ #define DMA_ETOP_ENDIANNESS (0xf << 8) /* endianness swap etop channels */ #define DMA_WEIGHT (BIT(17) | BIT(16)) /* default channel wheight */

@@ -218,7 +218,7 @@ ltq_dma_init(struct platform_device *pdev) { struct clk *clk; struct resource *res; - unsigned id; + unsigned int id, nchannels; int i;

res = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -240,17 +240,18 @@ ltq_dma_init(struct platform_device *pdev) ltq_dma_w32(0, LTQ_DMA_IRNEN);

/* reset/configure each channel */ - for (i = 0; i < DMA_MAX_CHANNEL; i++) { + id = ltq_dma_r32(LTQ_DMA_ID); + nchannels = ((id & DMA_ID_CHNR) >> 20); + for (i = 0; i < nchannels; i++) { ltq_dma_w32(i, LTQ_DMA_CS); ltq_dma_w32(DMA_CHAN_RST, LTQ_DMA_CCTRL); ltq_dma_w32(DMA_POLL | DMA_CLK_DIV4, LTQ_DMA_CPOLL); ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL); }

- id = ltq_dma_r32(LTQ_DMA_ID); dev_info(&pdev->dev, "Init done - hw rev: %X, ports: %d, channels: %d\n", - id & 0x1f, (id >> 16) & 0xf, id >> 20); + id & 0x1f, (id >> 16) & 0xf, nchannels);

return 0; }

From: Jakub Kicinski kuba@kernel.org

[ Upstream commit 1e080f17750d1083e8a32f7b350584ae1cd7ff20 ]

mq / mqprio make the default child qdiscs visible. They only do so for the qdiscs which are within real_num_tx_queues when the device is registered. Depending on order of calls in the driver, or if user space changes config via ethtool -L the number of qdiscs visible under tc qdisc show will differ from the number of queues. This is confusing to users and potentially to system configuration scripts which try to make sure qdiscs have the right parameters.

Add a new Qdisc_ops callback and make relevant qdiscs TTRT.

Note that this uncovers the "shortcut" created by commit 1f27cde313d7 ("net: sched: use pfifo_fast for non real queues") The default child qdiscs beyond initial real_num_tx are always pfifo_fast, no matter what the sysfs setting is. Fixing this gets a little tricky because we'd need to keep a reference on whatever the default qdisc was at the time of creation. In practice this is likely an non-issue the qdiscs likely have to be configured to non-default settings, so whatever user space is doing such configuration can replace the pfifos... now that it will see them.

Reported-by: Matthew Massey matthewmassey@fb.com Reviewed-by: Dave Taht dave.taht@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- include/net/sch_generic.h | 4 ++++ net/core/dev.c | 2 ++ net/sched/sch_generic.c | 9 +++++++++ net/sched/sch_mq.c | 24 ++++++++++++++++++++++++ net/sched/sch_mqprio.c | 23 +++++++++++++++++++++++ 5 files changed, 62 insertions(+)

diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h index d737a6a2600be..286bc674a6e79 100644 --- a/include/net/sch_generic.h +++ b/include/net/sch_generic.h @@ -216,6 +216,8 @@ struct Qdisc_ops { struct netlink_ext_ack *extack); void (*attach)(struct Qdisc *sch); int (*change_tx_queue_len)(struct Qdisc *, unsigned int); + void (*change_real_num_tx)(struct Qdisc *sch, + unsigned int new_real_tx);

int (*dump)(struct Qdisc *, struct sk_buff *); int (*dump_stats)(struct Qdisc *, struct gnet_dump *); @@ -547,6 +549,8 @@ void qdisc_class_hash_grow(struct Qdisc *, struct Qdisc_class_hash *); void qdisc_class_hash_destroy(struct Qdisc_class_hash *);

int dev_qdisc_change_tx_queue_len(struct net_device *dev); +void dev_qdisc_change_real_num_tx(struct net_device *dev, + unsigned int new_real_tx); void dev_init_scheduler(struct net_device *dev); void dev_shutdown(struct net_device *dev); void dev_activate(struct net_device *dev); diff --git a/net/core/dev.c b/net/core/dev.c index 397bc2f50de08..2519a90a14827 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -2648,6 +2648,8 @@ int netif_set_real_num_tx_queues(struct net_device *dev, unsigned int txq) if (dev->num_tc) netif_setup_tc(dev, txq);

+ dev_qdisc_change_real_num_tx(dev, txq); + dev->real_num_tx_queues = txq;

if (disabling) { diff --git a/net/sched/sch_generic.c b/net/sched/sch_generic.c index 4e15913e7519e..2128b77d5cb33 100644 --- a/net/sched/sch_generic.c +++ b/net/sched/sch_generic.c @@ -1256,6 +1256,15 @@ static int qdisc_change_tx_queue_len(struct net_device *dev, return 0; }

+void dev_qdisc_change_real_num_tx(struct net_device *dev, + unsigned int new_real_tx) +{ + struct Qdisc *qdisc = dev->qdisc; + + if (qdisc->ops->change_real_num_tx) + qdisc->ops->change_real_num_tx(qdisc, new_real_tx); +} + int dev_qdisc_change_tx_queue_len(struct net_device *dev) { bool up = dev->flags & IFF_UP; diff --git a/net/sched/sch_mq.c b/net/sched/sch_mq.c index c008a316e9436..699b6bb444cea 100644 --- a/net/sched/sch_mq.c +++ b/net/sched/sch_mq.c @@ -130,6 +130,29 @@ static void mq_attach(struct Qdisc *sch) priv->qdiscs = NULL; }

+static void mq_change_real_num_tx(struct Qdisc *sch, unsigned int new_real_tx) +{ +#ifdef CONFIG_NET_SCHED + struct net_device *dev = qdisc_dev(sch); + struct Qdisc *qdisc; + unsigned int i; + + for (i = new_real_tx; i < dev->real_num_tx_queues; i++) { + qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping; + /* Only update the default qdiscs we created, + * qdiscs with handles are always hashed. + */ + if (qdisc != &noop_qdisc && !qdisc->handle) + qdisc_hash_del(qdisc); + } + for (i = dev->real_num_tx_queues; i < new_real_tx; i++) { + qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping; + if (qdisc != &noop_qdisc && !qdisc->handle) + qdisc_hash_add(qdisc, false); + } +#endif +} + static int mq_dump(struct Qdisc *sch, struct sk_buff *skb) { struct net_device *dev = qdisc_dev(sch); @@ -285,6 +308,7 @@ struct Qdisc_ops mq_qdisc_ops __read_mostly = { .init = mq_init, .destroy = mq_destroy, .attach = mq_attach, + .change_real_num_tx = mq_change_real_num_tx, .dump = mq_dump, .owner = THIS_MODULE, }; diff --git a/net/sched/sch_mqprio.c b/net/sched/sch_mqprio.c index fcfe41a954733..3fd0e5dd7ae3e 100644 --- a/net/sched/sch_mqprio.c +++ b/net/sched/sch_mqprio.c @@ -308,6 +308,28 @@ static void mqprio_attach(struct Qdisc *sch) priv->qdiscs = NULL; }

+static void mqprio_change_real_num_tx(struct Qdisc *sch, + unsigned int new_real_tx) +{ + struct net_device *dev = qdisc_dev(sch); + struct Qdisc *qdisc; + unsigned int i; + + for (i = new_real_tx; i < dev->real_num_tx_queues; i++) { + qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping; + /* Only update the default qdiscs we created, + * qdiscs with handles are always hashed. + */ + if (qdisc != &noop_qdisc && !qdisc->handle) + qdisc_hash_del(qdisc); + } + for (i = dev->real_num_tx_queues; i < new_real_tx; i++) { + qdisc = netdev_get_tx_queue(dev, i)->qdisc_sleeping; + if (qdisc != &noop_qdisc && !qdisc->handle) + qdisc_hash_add(qdisc, false); + } +} + static struct netdev_queue *mqprio_queue_get(struct Qdisc *sch, unsigned long cl) { @@ -632,6 +654,7 @@ static struct Qdisc_ops mqprio_qdisc_ops __read_mostly = { .init = mqprio_init, .destroy = mqprio_destroy, .attach = mqprio_attach, + .change_real_num_tx = mqprio_change_real_num_tx, .dump = mqprio_dump, .owner = THIS_MODULE, };

From: Peter Zijlstra peterz@infradead.org

[ Upstream commit 7fae4c24a2b84a66c7be399727aca11e7a888462 ]

It turns out that a single page of stack is trivial to overflow with all the tracing gunk enabled. Raise the exception stacks to 2 pages, which is still half the interrupt stacks, which are at 4 pages.

Reported-by: Michael Wang yun.wang@linux.alibaba.com Signed-off-by: Peter Zijlstra (Intel) peterz@infradead.org Link: https://lkml.kernel.org/r/YUIO9Ye98S5Eb68w@hirez.programming.kicks-ass.net Signed-off-by: Sasha Levin sashal@kernel.org --- arch/x86/include/asm/page_64_types.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/include/asm/page_64_types.h b/arch/x86/include/asm/page_64_types.h index 0b6352aabbd3d..b16fb3e185134 100644 --- a/arch/x86/include/asm/page_64_types.h +++ b/arch/x86/include/asm/page_64_types.h @@ -20,7 +20,7 @@ #define THREAD_SIZE (PAGE_SIZE << THREAD_SIZE_ORDER) #define CURRENT_MASK (~(THREAD_SIZE - 1))

-#define EXCEPTION_STACK_ORDER (0 + KASAN_STACK_ORDER) +#define EXCEPTION_STACK_ORDER (1 + KASAN_STACK_ORDER) #define EXCEPTION_STKSZ (PAGE_SIZE << EXCEPTION_STACK_ORDER)

#define DEBUG_STACK_ORDER (EXCEPTION_STACK_ORDER + 1)

From: Jonas Dreßler verdre@v0yd.nl

[ Upstream commit c606008b70627a2fc485732a53cc22f0f66d0981 ]

When creating a new virtual interface in mwifiex_add_virtual_intf(), we update our internal driver states like bss_type, bss_priority, bss_role and bss_mode to reflect the mode the firmware will be set to.

When switching virtual interface mode using mwifiex_init_new_priv_params() though, we currently only update bss_mode and bss_role. In order for the interface mode switch to actually work, we also need to update bss_type to its proper value, so do that.

This fixes a crash of the firmware (because the driver tries to execute commands that are invalid in AP mode) when switching from station mode to AP mode.

Signed-off-by: Jonas Dreßler verdre@v0yd.nl Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/marvell/mwifiex/cfg80211.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/marvell/mwifiex/cfg80211.c b/drivers/net/wireless/marvell/mwifiex/cfg80211.c index becde7c254de2..892247145f428 100644 --- a/drivers/net/wireless/marvell/mwifiex/cfg80211.c +++ b/drivers/net/wireless/marvell/mwifiex/cfg80211.c @@ -912,16 +912,20 @@ mwifiex_init_new_priv_params(struct mwifiex_private *priv, switch (type) { case NL80211_IFTYPE_STATION: case NL80211_IFTYPE_ADHOC: - priv->bss_role = MWIFIEX_BSS_ROLE_STA; + priv->bss_role = MWIFIEX_BSS_ROLE_STA; + priv->bss_type = MWIFIEX_BSS_TYPE_STA; break; case NL80211_IFTYPE_P2P_CLIENT: - priv->bss_role = MWIFIEX_BSS_ROLE_STA; + priv->bss_role = MWIFIEX_BSS_ROLE_STA; + priv->bss_type = MWIFIEX_BSS_TYPE_P2P; break; case NL80211_IFTYPE_P2P_GO: - priv->bss_role = MWIFIEX_BSS_ROLE_UAP; + priv->bss_role = MWIFIEX_BSS_ROLE_UAP; + priv->bss_type = MWIFIEX_BSS_TYPE_P2P; break; case NL80211_IFTYPE_AP: priv->bss_role = MWIFIEX_BSS_ROLE_UAP; + priv->bss_type = MWIFIEX_BSS_TYPE_UAP; break; default: mwifiex_dbg(adapter, ERROR,

From: Zheyu Ma zheyuma97@gmail.com

[ Upstream commit dbb4cfea6efe979ed153bd59a6a527a90d3d0ab3 ]

The interrupt handling should be related to the firmware version. If the driver matches an old firmware, then the driver should not handle interrupt such as i2c or dma, otherwise it will cause some errors.

This log reveals it:

[ 27.708641] INFO: trying to register non-static key. [ 27.710851] The code is fine but needs lockdep annotation, or maybe [ 27.712010] you didn't initialize this object before use? [ 27.712396] turning off the locking correctness validator. [ 27.712787] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169 [ 27.713349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 27.714149] Call Trace: [ 27.714329] <IRQ> [ 27.714480] dump_stack+0xba/0xf5 [ 27.714737] register_lock_class+0x873/0x8f0 [ 27.715052] ? __lock_acquire+0x323/0x1930 [ 27.715353] __lock_acquire+0x75/0x1930 [ 27.715636] lock_acquire+0x1dd/0x3e0 [ 27.715905] ? netup_i2c_interrupt+0x19/0x310 [ 27.716226] _raw_spin_lock_irqsave+0x4b/0x60 [ 27.716544] ? netup_i2c_interrupt+0x19/0x310 [ 27.716863] netup_i2c_interrupt+0x19/0x310 [ 27.717178] netup_unidvb_isr+0xd3/0x160 [ 27.717467] __handle_irq_event_percpu+0x53/0x3e0 [ 27.717808] handle_irq_event_percpu+0x35/0x90 [ 27.718129] handle_irq_event+0x39/0x60 [ 27.718409] handle_fasteoi_irq+0xc2/0x1d0 [ 27.718707] __common_interrupt+0x7f/0x150 [ 27.719008] common_interrupt+0xb4/0xd0 [ 27.719289] </IRQ> [ 27.719446] asm_common_interrupt+0x1e/0x40 [ 27.719747] RIP: 0010:native_safe_halt+0x17/0x20 [ 27.720084] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6 [ 27.721386] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246 [ 27.721758] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 [ 27.722262] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6 [ 27.722770] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001 [ 27.723277] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408 [ 27.723781] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000 [ 27.724289] default_idle+0x9/0x10 [ 27.724537] arch_cpu_idle+0xa/0x10 [ 27.724791] default_idle_call+0x6e/0x250 [ 27.725082] do_idle+0x1f0/0x2d0 [ 27.725326] cpu_startup_entry+0x18/0x20 [ 27.725613] start_secondary+0x11f/0x160 [ 27.725902] secondary_startup_64_no_verify+0xb0/0xbb [ 27.726272] BUG: kernel NULL pointer dereference, address: 0000000000000002 [ 27.726768] #PF: supervisor read access in kernel mode [ 27.727138] #PF: error_code(0x0000) - not-present page [ 27.727507] PGD 8000000118688067 P4D 8000000118688067 PUD 10feab067 PMD 0 [ 27.727999] Oops: 0000 [#1] PREEMPT SMP PTI [ 27.728302] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169 [ 27.728861] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 27.729660] RIP: 0010:netup_i2c_interrupt+0x23/0x310 [ 27.730019] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02 [ 27.731339] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046 [ 27.731716] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000 [ 27.732223] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8 [ 27.732727] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001 [ 27.733239] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000 [ 27.733745] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400 [ 27.734251] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 27.734821] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 27.735228] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0 [ 27.735735] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 27.736241] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 27.736744] Call Trace: [ 27.736924] <IRQ> [ 27.737074] netup_unidvb_isr+0xd3/0x160 [ 27.737363] __handle_irq_event_percpu+0x53/0x3e0 [ 27.737706] handle_irq_event_percpu+0x35/0x90 [ 27.738028] handle_irq_event+0x39/0x60 [ 27.738306] handle_fasteoi_irq+0xc2/0x1d0 [ 27.738602] __common_interrupt+0x7f/0x150 [ 27.738899] common_interrupt+0xb4/0xd0 [ 27.739176] </IRQ> [ 27.739331] asm_common_interrupt+0x1e/0x40 [ 27.739633] RIP: 0010:native_safe_halt+0x17/0x20 [ 27.739967] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6 [ 27.741275] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246 [ 27.741647] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 [ 27.742148] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6 [ 27.742652] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001 [ 27.743154] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408 [ 27.743652] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000 [ 27.744157] default_idle+0x9/0x10 [ 27.744405] arch_cpu_idle+0xa/0x10 [ 27.744658] default_idle_call+0x6e/0x250 [ 27.744948] do_idle+0x1f0/0x2d0 [ 27.745190] cpu_startup_entry+0x18/0x20 [ 27.745475] start_secondary+0x11f/0x160 [ 27.745761] secondary_startup_64_no_verify+0xb0/0xbb [ 27.746123] Modules linked in: [ 27.746348] Dumping ftrace buffer: [ 27.746596] (ftrace buffer empty) [ 27.746852] CR2: 0000000000000002 [ 27.747094] ---[ end trace ebafd46f83ab946d ]--- [ 27.747424] RIP: 0010:netup_i2c_interrupt+0x23/0x310 [ 27.747778] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02 [ 27.749082] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046 [ 27.749461] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000 [ 27.749966] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8 [ 27.750471] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001 [ 27.750976] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000 [ 27.751480] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400 [ 27.751986] FS: 0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000 [ 27.752560] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 27.752970] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0 [ 27.753481] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 27.753984] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 27.754487] Kernel panic - not syncing: Fatal exception in interrupt [ 27.755033] Dumping ftrace buffer: [ 27.755279] (ftrace buffer empty) [ 27.755534] Kernel Offset: disabled [ 27.755785] Rebooting in 1 seconds..

Signed-off-by: Zheyu Ma zheyuma97@gmail.com Signed-off-by: Sean Young sean@mess.org Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- .../pci/netup_unidvb/netup_unidvb_core.c | 27 +++++++++++-------- 1 file changed, 16 insertions(+), 11 deletions(-)

diff --git a/drivers/media/pci/netup_unidvb/netup_unidvb_core.c b/drivers/media/pci/netup_unidvb/netup_unidvb_core.c index ead59fabd15ff..de3fc62810e6c 100644 --- a/drivers/media/pci/netup_unidvb/netup_unidvb_core.c +++ b/drivers/media/pci/netup_unidvb/netup_unidvb_core.c @@ -267,19 +267,24 @@ static irqreturn_t netup_unidvb_isr(int irq, void *dev_id) if ((reg40 & AVL_IRQ_ASSERTED) != 0) { /* IRQ is being signaled */ reg_isr = readw(ndev->bmmio0 + REG_ISR); - if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) { - iret = netup_i2c_interrupt(&ndev->i2c[0]); - } else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) { - iret = netup_i2c_interrupt(&ndev->i2c[1]); - } else if (reg_isr & NETUP_UNIDVB_IRQ_SPI) { + if (reg_isr & NETUP_UNIDVB_IRQ_SPI) iret = netup_spi_interrupt(ndev->spi); - } else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) { - iret = netup_dma_interrupt(&ndev->dma[0]); - } else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) { - iret = netup_dma_interrupt(&ndev->dma[1]); - } else if (reg_isr & NETUP_UNIDVB_IRQ_CI) { - iret = netup_ci_interrupt(ndev); + else if (!ndev->old_fw) { + if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) { + iret = netup_i2c_interrupt(&ndev->i2c[0]); + } else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) { + iret = netup_i2c_interrupt(&ndev->i2c[1]); + } else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) { + iret = netup_dma_interrupt(&ndev->dma[0]); + } else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) { + iret = netup_dma_interrupt(&ndev->dma[1]); + } else if (reg_isr & NETUP_UNIDVB_IRQ_CI) { + iret = netup_ci_interrupt(ndev); + } else { + goto err; + } } else { +err: dev_err(&pci_dev->dev, "%s(): unknown interrupt 0x%x\n", __func__, reg_isr);

From: Ricardo Ribalda ribalda@chromium.org

[ Upstream commit ffccdde5f0e17d2f0d788a9d831a027187890eaa ]

The device is doing something unexpected with the control. Either because the protocol is not properly implemented or there has been a HW error.

Fixes v4l2-compliance:

Control ioctls (Input 0): fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22) test VIDIOC_G/S_CTRL: FAIL fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22) test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL

Reviewed-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Ricardo Ribalda ribalda@chromium.org Signed-off-by: Laurent Pinchart laurent.pinchart@ideasonboard.com Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/usb/uvc/uvc_video.c | 5 +++++ 1 file changed, 5 insertions(+)

diff --git a/drivers/media/usb/uvc/uvc_video.c b/drivers/media/usb/uvc/uvc_video.c index 56b058d60a0dc..9c26e586bb01d 100644 --- a/drivers/media/usb/uvc/uvc_video.c +++ b/drivers/media/usb/uvc/uvc_video.c @@ -117,6 +117,11 @@ int uvc_query_ctrl(struct uvc_device *dev, u8 query, u8 unit, case 5: /* Invalid unit */ case 6: /* Invalid control */ case 7: /* Invalid Request */ + /* + * The firmware has not properly implemented + * the control or there has been a HW error. + */ + return -EIO; case 8: /* Invalid value within range */ return -EINVAL; default: /* reserved or unknown */

From: Nadezda Lutovinova lutovinova@ispras.ru

[ Upstream commit cdfaf4752e6915a4b455ad4400133e540e4dc965 ]

If of_device_get_match_data() return NULL, then null pointer dereference occurs in s5p_mfc_init_pm(). The patch adds checking if dev->variant is NULL.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Nadezda Lutovinova lutovinova@ispras.ru Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/platform/s5p-mfc/s5p_mfc.c | 4 ++++ 1 file changed, 4 insertions(+)

diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc.c b/drivers/media/platform/s5p-mfc/s5p_mfc.c index 80bb58d31c3f6..0fc101bc58d67 100644 --- a/drivers/media/platform/s5p-mfc/s5p_mfc.c +++ b/drivers/media/platform/s5p-mfc/s5p_mfc.c @@ -1281,6 +1281,10 @@ static int s5p_mfc_probe(struct platform_device *pdev) }

dev->variant = of_device_get_match_data(&pdev->dev); + if (!dev->variant) { + dev_err(&pdev->dev, "Failed to get device MFC hardware variant information\n"); + return -ENOENT; + }

res = platform_get_resource(pdev, IORESOURCE_MEM, 0); dev->regs_base = devm_ioremap_resource(&pdev->dev, res);

From: Randy Dunlap rdunlap@infradead.org

[ Upstream commit c15b5fc054c3d6c97e953617605235c5cb8ce979 ]

When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls _printk(), but _printk() is a static inline function, not available as an extern. Since the purpose of the macro is to print the BUGCHECK info, make this config option depend on PRINTK.

Fixes multiple occurrences of this build error:

../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration 208 | int _printk(const char *s, ...) | ^~~~~~~ In file included from ../arch/ia64/include/asm/cmpxchg.h:5, ../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)' 146 | extern int _printk(const char *fmt, ...);

Cc: linux-ia64@vger.kernel.org Cc: Andrew Morton akpm@linux-foundation.org Cc: Tony Luck tony.luck@intel.com Cc: Chris Down chris@chrisdown.name Cc: Paul Gortmaker paul.gortmaker@windriver.com Cc: John Paul Adrian Glaubitz glaubitz@physik.fu-berlin.de Signed-off-by: Randy Dunlap rdunlap@infradead.org Signed-off-by: Petr Mladek pmladek@suse.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/ia64/Kconfig.debug | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/ia64/Kconfig.debug b/arch/ia64/Kconfig.debug index 1371efc9b0055..637ac79c29b6d 100644 --- a/arch/ia64/Kconfig.debug +++ b/arch/ia64/Kconfig.debug @@ -39,7 +39,7 @@ config DISABLE_VHPT

config IA64_DEBUG_CMPXCHG bool "Turn on compare-and-exchange bug checking (slow!)" - depends on DEBUG_KERNEL + depends on DEBUG_KERNEL && PRINTK help Selecting this option turns on bug checking for the IA-64 compare-and-exchange instructions. This is slow! Itaniums

From: Rafael J. Wysocki rafael.j.wysocki@intel.com

[ Upstream commit d3c4b6f64ad356c0d9ddbcf73fa471e6a841cc5c ]

ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de

During wakeup from system-wide sleep states, acpi_get_sleep_type_data() is called and it tries to get memory from the slab allocator in order to evaluate a control method, but if KFENCE is enabled in the kernel, the memory allocation attempt causes an IRQ work to be queued and a self-IPI to be sent to the CPU running the code which requires the memory controller to be ready, so if that happens too early in the wakeup path, it doesn't work.

Prevent that from taking place by calling acpi_get_sleep_type_data() for S0 upfront, when preparing to enter a given sleep state, and saving the data obtained by it for later use during system wakeup.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271 Reported-by: Reik Keutterling spielkind@gmail.com Tested-by: Reik Keutterling spielkind@gmail.com Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/acpi/acpica/acglobal.h | 2 ++ drivers/acpi/acpica/hwesleep.c | 8 ++------ drivers/acpi/acpica/hwsleep.c | 11 ++++------- drivers/acpi/acpica/hwxfsleep.c | 7 +++++++ 4 files changed, 15 insertions(+), 13 deletions(-)

diff --git a/drivers/acpi/acpica/acglobal.h b/drivers/acpi/acpica/acglobal.h index 1e6204518496c..38712fa4dd9d2 100644 --- a/drivers/acpi/acpica/acglobal.h +++ b/drivers/acpi/acpica/acglobal.h @@ -224,6 +224,8 @@ extern struct acpi_bit_register_info acpi_gbl_bit_register_info[ACPI_NUM_BITREG]; ACPI_GLOBAL(u8, acpi_gbl_sleep_type_a); ACPI_GLOBAL(u8, acpi_gbl_sleep_type_b); +ACPI_GLOBAL(u8, acpi_gbl_sleep_type_a_s0); +ACPI_GLOBAL(u8, acpi_gbl_sleep_type_b_s0);

/***************************************************************************** * diff --git a/drivers/acpi/acpica/hwesleep.c b/drivers/acpi/acpica/hwesleep.c index e0ad3f11142e4..9516966124ae3 100644 --- a/drivers/acpi/acpica/hwesleep.c +++ b/drivers/acpi/acpica/hwesleep.c @@ -147,17 +147,13 @@ acpi_status acpi_hw_extended_sleep(u8 sleep_state)

acpi_status acpi_hw_extended_wake_prep(u8 sleep_state) { - acpi_status status; u8 sleep_type_value;

ACPI_FUNCTION_TRACE(hw_extended_wake_prep);

- status = acpi_get_sleep_type_data(ACPI_STATE_S0, - &acpi_gbl_sleep_type_a, - &acpi_gbl_sleep_type_b); - if (ACPI_SUCCESS(status)) { + if (acpi_gbl_sleep_type_a_s0 != ACPI_SLEEP_TYPE_INVALID) { sleep_type_value = - ((acpi_gbl_sleep_type_a << ACPI_X_SLEEP_TYPE_POSITION) & + ((acpi_gbl_sleep_type_a_s0 << ACPI_X_SLEEP_TYPE_POSITION) & ACPI_X_SLEEP_TYPE_MASK);

(void)acpi_write((u64)(sleep_type_value | ACPI_X_SLEEP_ENABLE), diff --git a/drivers/acpi/acpica/hwsleep.c b/drivers/acpi/acpica/hwsleep.c index d8b8fc2ff5633..f4282370947c8 100644 --- a/drivers/acpi/acpica/hwsleep.c +++ b/drivers/acpi/acpica/hwsleep.c @@ -179,7 +179,7 @@ acpi_status acpi_hw_legacy_sleep(u8 sleep_state)

acpi_status acpi_hw_legacy_wake_prep(u8 sleep_state) { - acpi_status status; + acpi_status status = AE_OK; struct acpi_bit_register_info *sleep_type_reg_info; struct acpi_bit_register_info *sleep_enable_reg_info; u32 pm1a_control; @@ -192,10 +192,7 @@ acpi_status acpi_hw_legacy_wake_prep(u8 sleep_state) * This is unclear from the ACPI Spec, but it is required * by some machines. */ - status = acpi_get_sleep_type_data(ACPI_STATE_S0, - &acpi_gbl_sleep_type_a, - &acpi_gbl_sleep_type_b); - if (ACPI_SUCCESS(status)) { + if (acpi_gbl_sleep_type_a_s0 != ACPI_SLEEP_TYPE_INVALID) { sleep_type_reg_info = acpi_hw_get_bit_register_info(ACPI_BITREG_SLEEP_TYPE); sleep_enable_reg_info = @@ -216,9 +213,9 @@ acpi_status acpi_hw_legacy_wake_prep(u8 sleep_state)

/* Insert the SLP_TYP bits */

- pm1a_control |= (acpi_gbl_sleep_type_a << + pm1a_control |= (acpi_gbl_sleep_type_a_s0 << sleep_type_reg_info->bit_position); - pm1b_control |= (acpi_gbl_sleep_type_b << + pm1b_control |= (acpi_gbl_sleep_type_b_s0 << sleep_type_reg_info->bit_position);

/* Write the control registers and ignore any errors */ diff --git a/drivers/acpi/acpica/hwxfsleep.c b/drivers/acpi/acpica/hwxfsleep.c index 3f22f7dd4556d..dc1e44ccaae20 100644 --- a/drivers/acpi/acpica/hwxfsleep.c +++ b/drivers/acpi/acpica/hwxfsleep.c @@ -288,6 +288,13 @@ acpi_status acpi_enter_sleep_state_prep(u8 sleep_state) return_ACPI_STATUS(status); }

+ status = acpi_get_sleep_type_data(ACPI_STATE_S0, + &acpi_gbl_sleep_type_a_s0, + &acpi_gbl_sleep_type_b_s0); + if (ACPI_FAILURE(status)) { + acpi_gbl_sleep_type_a_s0 = ACPI_SLEEP_TYPE_INVALID; + } + /* Execute the _PTS method (Prepare To Sleep) */

arg_list.count = 1;

From: Steven Rostedt (VMware) rostedt@goodmis.org

[ Upstream commit 49d67e445742bbcb03106b735b2ab39f6e5c56bc ]

The tracefs file system is by default mounted such that only root user can access it. But there are legitimate reasons to create a group and allow those added to the group to have access to tracing. By changing the permissions of the tracefs mount point to allow access, it will allow group access to the tracefs directory.

There should not be any real reason to allow all access to the tracefs directory as it contains sensitive information. Have the default permission of directories being created not have any OTH (other) bits set, such that an admin that wants to give permission to a group has to first disable all OTH bits in the file system.

Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org

Signed-off-by: Steven Rostedt (VMware) rostedt@goodmis.org Signed-off-by: Sasha Levin sashal@kernel.org --- fs/tracefs/inode.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/tracefs/inode.c b/fs/tracefs/inode.c index 7098c49f36934..990f794b1dd0a 100644 --- a/fs/tracefs/inode.c +++ b/fs/tracefs/inode.c @@ -427,7 +427,8 @@ static struct dentry *__create_dir(const char *name, struct dentry *parent, if (unlikely(!inode)) return failed_creating(dentry);

- inode->i_mode = S_IFDIR | S_IRWXU | S_IRUGO | S_IXUGO; + /* Do not set bits for OTH */ + inode->i_mode = S_IFDIR | S_IRWXU | S_IRUSR| S_IRGRP | S_IXUSR | S_IXGRP; inode->i_op = ops; inode->i_fop = &simple_dir_operations;

From: André Almeida andrealmeid@collabora.com

[ Upstream commit 2835f327bd1240508db2c89fe94a056faa53c49a ]

Some buggy firmware and/or brand new batteries can support a charge that's slightly over the reported design capacity. In such cases, the kernel will report to userspace that the charging state of the battery is "Unknown", when in reality the battery charge is "Full", at least from the design capacity point of view. Make the fallback condition accepts capacities over the designed capacity so userspace knows that is full.

Signed-off-by: André Almeida andrealmeid@collabora.com Reviewed-by: Hans de Goede hdegoede@redhat.com Reviewed-by: Sebastian Reichel sebastian.reichel@collabora.com Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/acpi/battery.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/acpi/battery.c b/drivers/acpi/battery.c index 674a0e92b798f..0bbf8b453ebf2 100644 --- a/drivers/acpi/battery.c +++ b/drivers/acpi/battery.c @@ -198,7 +198,7 @@ static int acpi_battery_is_charged(struct acpi_battery *battery) return 1;

/* fallback to using design values for broken batteries */ - if (battery->design_capacity == battery->capacity_now) + if (battery->design_capacity <= battery->capacity_now) return 1;

/* we don't do any sort of metric based on percentages */

From: Zheyu Ma zheyuma97@gmail.com

[ Upstream commit 738216c1953e802aa9f930c5d15b8f9092c847ff ]

In r592_remove(), the driver will free dma after freeing the host, which may cause a UAF bug.

The following log reveals it:

[ 45.361796 ] BUG: KASAN: use-after-free in r592_remove+0x269/0x350 [r592] [ 45.364286 ] Call Trace: [ 45.364472 ] dump_stack_lvl+0xa8/0xd1 [ 45.364751 ] print_address_description+0x87/0x3b0 [ 45.365137 ] kasan_report+0x172/0x1c0 [ 45.365415 ] ? r592_remove+0x269/0x350 [r592] [ 45.365834 ] ? r592_remove+0x269/0x350 [r592] [ 45.366168 ] __asan_report_load8_noabort+0x14/0x20 [ 45.366531 ] r592_remove+0x269/0x350 [r592] [ 45.378785 ] [ 45.378903 ] Allocated by task 4674: [ 45.379162 ] ____kasan_kmalloc+0xb5/0xe0 [ 45.379455 ] __kasan_kmalloc+0x9/0x10 [ 45.379730 ] __kmalloc+0x150/0x280 [ 45.379984 ] memstick_alloc_host+0x2a/0x190 [ 45.380664 ] [ 45.380781 ] Freed by task 5509: [ 45.381014 ] kasan_set_track+0x3d/0x70 [ 45.381293 ] kasan_set_free_info+0x23/0x40 [ 45.381635 ] ____kasan_slab_free+0x10b/0x140 [ 45.381950 ] __kasan_slab_free+0x11/0x20 [ 45.382241 ] slab_free_freelist_hook+0x81/0x150 [ 45.382575 ] kfree+0x13e/0x290 [ 45.382805 ] memstick_free+0x1c/0x20 [ 45.383070 ] device_release+0x9c/0x1d0 [ 45.383349 ] kobject_put+0x2ef/0x4c0 [ 45.383616 ] put_device+0x1f/0x30 [ 45.383865 ] memstick_free_host+0x24/0x30 [ 45.384162 ] r592_remove+0x242/0x350 [r592] [ 45.384473 ] pci_device_remove+0xa9/0x250

Signed-off-by: Zheyu Ma zheyuma97@gmail.com Link: https://lore.kernel.org/r/1634383581-11055-1-git-send-email-zheyuma97@gmail.... Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/memstick/host/r592.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/memstick/host/r592.c b/drivers/memstick/host/r592.c index 4559593ecd5a9..4728a42d54b88 100644 --- a/drivers/memstick/host/r592.c +++ b/drivers/memstick/host/r592.c @@ -840,15 +840,15 @@ static void r592_remove(struct pci_dev *pdev) } memstick_remove_host(dev->host);

+ if (dev->dummy_dma_page) + dma_free_coherent(&pdev->dev, PAGE_SIZE, dev->dummy_dma_page, + dev->dummy_dma_page_physical_address); + free_irq(dev->irq, dev); iounmap(dev->mmio); pci_release_regions(pdev); pci_disable_device(pdev); memstick_free_host(dev->host); - - if (dev->dummy_dma_page) - dma_free_coherent(&pdev->dev, PAGE_SIZE, dev->dummy_dma_page, - dev->dummy_dma_page_physical_address); }

#ifdef CONFIG_PM_SLEEP

From: Lasse Collin lasse.collin@tukaani.org

[ Upstream commit 4f8d7abaa413c34da9d751289849dbfb7c977d05 ]

This might matter, for example, if the underlying type of enum xz_check was a signed char. In such a case the validation wouldn't have caught an unsupported header. I don't know if this problem can occur in the kernel on any arch but it's still good to fix it because some people might copy the XZ code to their own projects from Linux instead of the upstream XZ Embedded repository.

This change may increase the code size by a few bytes. An alternative would have been to use an unsigned int instead of enum xz_check but using an enumeration looks cleaner.

Link: https://lore.kernel.org/r/20211010213145.17462-3-xiang@kernel.org Signed-off-by: Lasse Collin lasse.collin@tukaani.org Signed-off-by: Gao Xiang hsiangkao@linux.alibaba.com Signed-off-by: Sasha Levin sashal@kernel.org --- lib/xz/xz_dec_stream.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/lib/xz/xz_dec_stream.c b/lib/xz/xz_dec_stream.c index bd1d182419d7e..0b161f90d8d80 100644 --- a/lib/xz/xz_dec_stream.c +++ b/lib/xz/xz_dec_stream.c @@ -402,12 +402,12 @@ static enum xz_ret dec_stream_header(struct xz_dec *s) * we will accept other check types too, but then the check won't * be verified and a warning (XZ_UNSUPPORTED_CHECK) will be given. */ + if (s->temp.buf[HEADER_MAGIC_SIZE + 1] > XZ_CHECK_MAX) + return XZ_OPTIONS_ERROR; + s->check_type = s->temp.buf[HEADER_MAGIC_SIZE + 1];

#ifdef XZ_DEC_ANY_CHECK - if (s->check_type > XZ_CHECK_MAX) - return XZ_OPTIONS_ERROR; - if (s->check_type > XZ_CHECK_CRC32) return XZ_UNSUPPORTED_CHECK; #else

From: Kalesh Singh kaleshsingh@google.com

[ Upstream commit 7ce1bb83a14019f8c396d57ec704d19478747716 ]

If CONFIG_CFI_CLANG=y, attempting to read an event histogram will cause the kernel to panic due to failed CFI check.

1. echo 'hist:keys=common_pid' >> events/sched/sched_switch/trigger 2. cat events/sched/sched_switch/hist 3. kernel panics on attempting to read hist

This happens because the sort() function expects a generic int (*)(const void *, const void *) pointer for the compare function. To prevent this CFI failure, change tracing map cmp_entries_* function signatures to match this.

Also, fix the build error reported by the kernel test robot [1].

[1] https://lore.kernel.org/r/202110141140.zzi4dRh4-lkp@intel.com/

Link: https://lkml.kernel.org/r/20211014045217.3265162-1-kaleshsingh@google.com

Signed-off-by: Kalesh Singh kaleshsingh@google.com Reported-by: kernel test robot lkp@intel.com Signed-off-by: Steven Rostedt (VMware) rostedt@goodmis.org Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/trace/tracing_map.c | 40 ++++++++++++++++++++++---------------- 1 file changed, 23 insertions(+), 17 deletions(-)

diff --git a/kernel/trace/tracing_map.c b/kernel/trace/tracing_map.c index 9e31bfc818ff8..10657b8dc2c2d 100644 --- a/kernel/trace/tracing_map.c +++ b/kernel/trace/tracing_map.c @@ -834,29 +834,35 @@ int tracing_map_init(struct tracing_map *map) return err; }

-static int cmp_entries_dup(const struct tracing_map_sort_entry **a, - const struct tracing_map_sort_entry **b) +static int cmp_entries_dup(const void *A, const void *B) { + const struct tracing_map_sort_entry *a, *b; int ret = 0;

- if (memcmp((*a)->key, (*b)->key, (*a)->elt->map->key_size)) + a = *(const struct tracing_map_sort_entry **)A; + b = *(const struct tracing_map_sort_entry **)B; + + if (memcmp(a->key, b->key, a->elt->map->key_size)) ret = 1;

return ret; }

-static int cmp_entries_sum(const struct tracing_map_sort_entry **a, - const struct tracing_map_sort_entry **b) +static int cmp_entries_sum(const void *A, const void *B) { const struct tracing_map_elt *elt_a, *elt_b; + const struct tracing_map_sort_entry *a, *b; struct tracing_map_sort_key *sort_key; struct tracing_map_field *field; tracing_map_cmp_fn_t cmp_fn; void *val_a, *val_b; int ret = 0;

- elt_a = (*a)->elt; - elt_b = (*b)->elt; + a = *(const struct tracing_map_sort_entry **)A; + b = *(const struct tracing_map_sort_entry **)B; + + elt_a = a->elt; + elt_b = b->elt;

sort_key = &elt_a->map->sort_key;

@@ -873,18 +879,21 @@ static int cmp_entries_sum(const struct tracing_map_sort_entry **a, return ret; }

-static int cmp_entries_key(const struct tracing_map_sort_entry **a, - const struct tracing_map_sort_entry **b) +static int cmp_entries_key(const void *A, const void *B) { const struct tracing_map_elt *elt_a, *elt_b; + const struct tracing_map_sort_entry *a, *b; struct tracing_map_sort_key *sort_key; struct tracing_map_field *field; tracing_map_cmp_fn_t cmp_fn; void *val_a, *val_b; int ret = 0;

- elt_a = (*a)->elt; - elt_b = (*b)->elt; + a = *(const struct tracing_map_sort_entry **)A; + b = *(const struct tracing_map_sort_entry **)B; + + elt_a = a->elt; + elt_b = b->elt;

sort_key = &elt_a->map->sort_key;

@@ -989,10 +998,8 @@ static void sort_secondary(struct tracing_map *map, struct tracing_map_sort_key *primary_key, struct tracing_map_sort_key *secondary_key) { - int (*primary_fn)(const struct tracing_map_sort_entry **, - const struct tracing_map_sort_entry **); - int (*secondary_fn)(const struct tracing_map_sort_entry **, - const struct tracing_map_sort_entry **); + int (*primary_fn)(const void *, const void *); + int (*secondary_fn)(const void *, const void *); unsigned i, start = 0, n_sub = 1;

if (is_key(map, primary_key->field_idx)) @@ -1061,8 +1068,7 @@ int tracing_map_sort_entries(struct tracing_map *map, unsigned int n_sort_keys, struct tracing_map_sort_entry ***sort_entries) { - int (*cmp_entries_fn)(const struct tracing_map_sort_entry **, - const struct tracing_map_sort_entry **); + int (*cmp_entries_fn)(const void *, const void *); struct tracing_map_sort_entry *sort_entry, **entries; int i, n_entries, ret;

From: Ye Bin yebin10@huawei.com

[ Upstream commit 39fbef4b0f77f9c89c8f014749ca533643a37c9f ]

The following kernel crash can be triggered:

[ 89.266592] ------------[ cut here ]------------ [ 89.267427] kernel BUG at fs/buffer.c:3020! [ 89.268264] invalid opcode: 0000 [#1] SMP KASAN PTI [ 89.269116] CPU: 7 PID: 1750 Comm: kmmpd-loop0 Not tainted 5.10.0-862.14.0.6.x86_64-08610-gc932cda3cef4-dirty #20 [ 89.273169] RIP: 0010:submit_bh_wbc.isra.0+0x538/0x6d0 [ 89.277157] RSP: 0018:ffff888105ddfd08 EFLAGS: 00010246 [ 89.278093] RAX: 0000000000000005 RBX: ffff888124231498 RCX: ffffffffb2772612 [ 89.279332] RDX: 1ffff11024846293 RSI: 0000000000000008 RDI: ffff888124231498 [ 89.280591] RBP: ffff8881248cc000 R08: 0000000000000001 R09: ffffed1024846294 [ 89.281851] R10: ffff88812423149f R11: ffffed1024846293 R12: 0000000000003800 [ 89.283095] R13: 0000000000000001 R14: 0000000000000000 R15: ffff8881161f7000 [ 89.284342] FS: 0000000000000000(0000) GS:ffff88839b5c0000(0000) knlGS:0000000000000000 [ 89.285711] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 89.286701] CR2: 00007f166ebc01a0 CR3: 0000000435c0e000 CR4: 00000000000006e0 [ 89.287919] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 89.289138] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 89.290368] Call Trace: [ 89.290842] write_mmp_block+0x2ca/0x510 [ 89.292218] kmmpd+0x433/0x9a0 [ 89.294902] kthread+0x2dd/0x3e0 [ 89.296268] ret_from_fork+0x22/0x30 [ 89.296906] Modules linked in:

by running the following commands:

1. mkfs.ext4 -O mmp /dev/sda -b 1024 2. mount /dev/sda /home/test 3. echo "/dev/sda" > /sys/power/resume

That happens because swsusp_check() calls set_blocksize() on the target partition which confuses the file system:

Thread1 Thread2 mount /dev/sda /home/test get s_mmp_bh --> has mapped flag start kmmpd thread echo "/dev/sda" > /sys/power/resume resume_store software_resume swsusp_check set_blocksize truncate_inode_pages_range truncate_cleanup_page block_invalidatepage discard_buffer --> clean mapped flag write_mmp_block submit_bh submit_bh_wbc BUG_ON(!buffer_mapped(bh))

To address this issue, modify swsusp_check() to open the target block device with exclusive access.

Signed-off-by: Ye Bin yebin10@huawei.com [ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki rafael.j.wysocki@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- kernel/power/swap.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/kernel/power/swap.c b/kernel/power/swap.c index e9494c29f1ca4..b5b97df142d26 100644 --- a/kernel/power/swap.c +++ b/kernel/power/swap.c @@ -1512,9 +1512,10 @@ end: int swsusp_check(void) { int error; + void *holder;

hib_resume_bdev = blkdev_get_by_dev(swsusp_resume_device, - FMODE_READ, NULL); + FMODE_READ | FMODE_EXCL, &holder); if (!IS_ERR(hib_resume_bdev)) { set_blocksize(hib_resume_bdev, PAGE_SIZE); clear_page(swsusp_header); @@ -1536,7 +1537,7 @@ int swsusp_check(void)

put: if (error) - blkdev_put(hib_resume_bdev, FMODE_READ); + blkdev_put(hib_resume_bdev, FMODE_READ | FMODE_EXCL); else pr_debug("Image signature found, resuming\n"); } else {

From: Tetsuo Handa penguin-kernel@i-love.sakura.ne.jp

[ Upstream commit f91488ee15bd3cac467e2d6a361fc2d34d1052ae ]

syzbot is reporting kernel panic at smk_cipso_doi() due to memory allocation fault injection [1]. The reason for need to use panic() was not explained. But since no fix was proposed for 18 months, for now let's use __GFP_NOFAIL for utilizing syzbot resource on other bugs.

Link: https://syzkaller.appspot.com/bug?extid=89731ccb6fec15ce1c22 [1] Reported-by: syzbot syzbot+89731ccb6fec15ce1c22@syzkaller.appspotmail.com Signed-off-by: Tetsuo Handa penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Casey Schaufler casey@schaufler-ca.com Signed-off-by: Sasha Levin sashal@kernel.org --- security/smack/smackfs.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/security/smack/smackfs.c b/security/smack/smackfs.c index 25705a72d31bc..9fdf404a318f9 100644 --- a/security/smack/smackfs.c +++ b/security/smack/smackfs.c @@ -721,9 +721,7 @@ static void smk_cipso_doi(void) printk(KERN_WARNING "%s:%d remove rc = %d\n", __func__, __LINE__, rc);

- doip = kmalloc(sizeof(struct cipso_v4_doi), GFP_KERNEL); - if (doip == NULL) - panic("smack: Failed to initialize cipso DOI.\n"); + doip = kmalloc(sizeof(struct cipso_v4_doi), GFP_KERNEL | __GFP_NOFAIL); doip->map.std = NULL; doip->doi = smk_cipso_doi_value; doip->type = CIPSO_V4_MAP_PASS;

From: Stephen Suryaputra ssuryaextr@gmail.com

[ Upstream commit 61e18ce7348bfefb5688a8bcd4b4d6b37c0f9b2a ]

When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr should not be generated. But it isn't the case for GRE (as well as GRE6) and SIT tunnels. Make it so that tunnels consider the addr_gen_mode, especially for IN6_ADDR_GEN_MODE_NONE.

Do this in add_v4_addrs() to cover both GRE and SIT only if the addr scope is link.

Signed-off-by: Stephen Suryaputra ssuryaextr@gmail.com Acked-by: Antonio Quartulli a@unstable.cc Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.com Signed-off-by: Jakub Kicinski kuba@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- net/ipv6/addrconf.c | 3 +++ 1 file changed, 3 insertions(+)

diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index 76c097552ea74..9d8b791f63efc 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -3054,6 +3054,9 @@ static void sit_add_v4_addrs(struct inet6_dev *idev) memcpy(&addr.s6_addr32[3], idev->dev->dev_addr, 4);

if (idev->dev->flags&IFF_POINTOPOINT) { + if (idev->cnf.addr_gen_mode == IN6_ADDR_GEN_MODE_NONE) + return; + addr.s6_addr32[0] = htonl(0xfe800000); scope = IFA_LINK; plen = 64;

From: Yang Yingliang yangyingliang@huawei.com

[ Upstream commit ca9b8f56ec089d3a436050afefd17b7237301f47 ]

Fix the missing clk_disable_unprepare() before return from bcm_qspi_probe() in the error handling case.

Reported-by: Hulk Robot hulkci@huawei.com Signed-off-by: Yang Yingliang yangyingliang@huawei.com Link: https://lore.kernel.org/r/20211018073413.2029081-1-yangyingliang@huawei.com Signed-off-by: Mark Brown broonie@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/spi/spi-bcm-qspi.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c index 4ee92f7ca20bd..b2fd7a3691964 100644 --- a/drivers/spi/spi-bcm-qspi.c +++ b/drivers/spi/spi-bcm-qspi.c @@ -1305,7 +1305,7 @@ int bcm_qspi_probe(struct platform_device *pdev, &qspi->dev_ids[val]); if (ret < 0) { dev_err(&pdev->dev, "IRQ %s not found\n", name); - goto qspi_probe_err; + goto qspi_unprepare_err; }

qspi->dev_ids[val].dev = qspi; @@ -1320,7 +1320,7 @@ int bcm_qspi_probe(struct platform_device *pdev, if (!num_ints) { dev_err(&pdev->dev, "no IRQs registered, cannot init driver\n"); ret = -EINVAL; - goto qspi_probe_err; + goto qspi_unprepare_err; }

/* @@ -1371,6 +1371,7 @@ int bcm_qspi_probe(struct platform_device *pdev,

qspi_reg_err: bcm_qspi_hw_uninit(qspi); +qspi_unprepare_err: clk_disable_unprepare(qspi->clk); qspi_probe_err: kfree(qspi->dev_ids);

From: Sven Schnelle svens@stackframe.org

[ Upstream commit 1030d681319b43869e0d5b568b9d0226652d1a6f ]

I've got the following splat after enabling preemption:

[ 3.724721] BUG: using __this_cpu_add() in preemptible [00000000] code: swapper/0/1 [ 3.734630] caller is __this_cpu_preempt_check+0x38/0x50 [ 3.740635] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.15.0-rc4-64bit+ #324 [ 3.744605] Hardware name: 9000/785/C8000 [ 3.744605] Backtrace: [ 3.744605] [<00000000401d9d58>] show_stack+0x74/0xb0 [ 3.744605] [<0000000040c27bd4>] dump_stack_lvl+0x10c/0x188 [ 3.744605] [<0000000040c27c84>] dump_stack+0x34/0x48 [ 3.744605] [<0000000040c33438>] check_preemption_disabled+0x178/0x1b0 [ 3.744605] [<0000000040c334f8>] __this_cpu_preempt_check+0x38/0x50 [ 3.744605] [<00000000401d632c>] flush_tlb_all+0x58/0x2e0 [ 3.744605] [<00000000401075c0>] 0x401075c0 [ 3.744605] [<000000004010b8fc>] 0x4010b8fc [ 3.744605] [<00000000401080fc>] 0x401080fc [ 3.744605] [<00000000401d5224>] do_one_initcall+0x128/0x378 [ 3.744605] [<0000000040102de8>] 0x40102de8 [ 3.744605] [<0000000040c33864>] kernel_init+0x60/0x3a8 [ 3.744605] [<00000000401d1020>] ret_from_kernel_thread+0x20/0x28 [ 3.744605]

Fix this by moving the __inc_irq_stat() into the locked section.

Signed-off-by: Sven Schnelle svens@stackframe.org Signed-off-by: Helge Deller deller@gmx.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/parisc/mm/init.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/parisc/mm/init.c b/arch/parisc/mm/init.c index 10a52664e29f0..038fcb6c76dc1 100644 --- a/arch/parisc/mm/init.c +++ b/arch/parisc/mm/init.c @@ -895,9 +895,9 @@ void flush_tlb_all(void) { int do_recycle;

- __inc_irq_stat(irq_tlb_count); do_recycle = 0; spin_lock(&sid_lock); + __inc_irq_stat(irq_tlb_count); if (dirty_space_ids > RECYCLE_THRESHOLD) { BUG_ON(recycle_inuse); /* FIXME: Use a semaphore/wait queue here */ get_dirty_sids(&recycle_ndirty,recycle_dirty_array); @@ -916,8 +916,8 @@ void flush_tlb_all(void) #else void flush_tlb_all(void) { - __inc_irq_stat(irq_tlb_count); spin_lock(&sid_lock); + __inc_irq_stat(irq_tlb_count); flush_tlb_all_local(NULL); recycle_sids(); spin_unlock(&sid_lock);

From: Sven Schnelle svens@stackframe.org

[ Upstream commit 8e0ba125c2bf1030af3267058019ba86da96863f ]

With 64 bit kernels unwind_special() is not working because it compares the pc to the address of the function descriptor. Add a helper function that compares pc with the dereferenced address. This fixes all of the backtraces on my c8000. Without this changes, a lot of backtraces are missing in kdb or the show-all-tasks command from /proc/sysrq-trigger.

Signed-off-by: Sven Schnelle svens@stackframe.org Signed-off-by: Helge Deller deller@gmx.de Signed-off-by: Sasha Levin sashal@kernel.org --- arch/parisc/kernel/unwind.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/arch/parisc/kernel/unwind.c b/arch/parisc/kernel/unwind.c index 2d14f17838d23..fa52c939e8a3b 100644 --- a/arch/parisc/kernel/unwind.c +++ b/arch/parisc/kernel/unwind.c @@ -21,6 +21,8 @@ #include <asm/ptrace.h>

#include <asm/unwind.h> +#include <asm/switch_to.h> +#include <asm/sections.h>

/* #define DEBUG 1 */ #ifdef DEBUG @@ -203,6 +205,11 @@ int __init unwind_init(void) return 0; }

+static bool pc_is_kernel_fn(unsigned long pc, void *fn) +{ + return (unsigned long)dereference_kernel_function_descriptor(fn) == pc; +} + static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int frame_size) { /* @@ -221,7 +228,7 @@ static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int extern void * const _call_on_stack; #endif /* CONFIG_IRQSTACKS */

- if (pc == (unsigned long) &handle_interruption) { + if (pc_is_kernel_fn(pc, handle_interruption)) { struct pt_regs *regs = (struct pt_regs *)(info->sp - frame_size - PT_SZ_ALGN); dbg("Unwinding through handle_interruption()\n"); info->prev_sp = regs->gr[30]; @@ -229,13 +236,13 @@ static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int return 1; }

- if (pc == (unsigned long) &ret_from_kernel_thread || - pc == (unsigned long) &syscall_exit) { + if (pc_is_kernel_fn(pc, ret_from_kernel_thread) || + pc_is_kernel_fn(pc, syscall_exit)) { info->prev_sp = info->prev_ip = 0; return 1; }

- if (pc == (unsigned long) &intr_return) { + if (pc_is_kernel_fn(pc, intr_return)) { struct pt_regs *regs;

dbg("Found intr_return()\n"); @@ -246,20 +253,20 @@ static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int return 1; }

- if (pc == (unsigned long) &_switch_to_ret) { + if (pc_is_kernel_fn(pc, _switch_to) || + pc_is_kernel_fn(pc, _switch_to_ret)) { info->prev_sp = info->sp - CALLEE_SAVE_FRAME_SIZE; info->prev_ip = *(unsigned long *)(info->prev_sp - RP_OFFSET); return 1; }

#ifdef CONFIG_IRQSTACKS - if (pc == (unsigned long) &_call_on_stack) { + if (pc_is_kernel_fn(pc, _call_on_stack)) { info->prev_sp = *(unsigned long *)(info->sp - FRAME_SIZE - REG_SZ); info->prev_ip = *(unsigned long *)(info->sp - FRAME_SIZE - RP_OFFSET); return 1; } #endif - return 0; }

From: Desmond Cheong Zhi Xi desmondcheongzx@gmail.com

[ Upstream commit 49d8a5606428ca0962d09050a5af81461ff90fbb ]

Before freeing struct sco_conn, all delayed timeout work should be cancelled. Otherwise, sco_sock_timeout could potentially use the sco_conn after it has been freed.

Additionally, sco_conn.timeout_work should be initialized when the connection is allocated, not when the channel is added. This is because an sco_conn can create channels with multiple sockets over its lifetime, which happens if sockets are released but the connection isn't deleted.

Fixes: ba316be1b6a0 ("Bluetooth: schedule SCO timeouts with delayed_work") Signed-off-by: Desmond Cheong Zhi Xi desmondcheongzx@gmail.com Signed-off-by: Luiz Augusto von Dentz luiz.von.dentz@intel.com Signed-off-by: Sasha Levin sashal@kernel.org --- net/bluetooth/sco.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/net/bluetooth/sco.c b/net/bluetooth/sco.c index d052b454dc4e1..1e0a1c0a56b57 100644 --- a/net/bluetooth/sco.c +++ b/net/bluetooth/sco.c @@ -133,6 +133,7 @@ static struct sco_conn *sco_conn_add(struct hci_conn *hcon) return NULL;

spin_lock_init(&conn->lock); + INIT_DELAYED_WORK(&conn->timeout_work, sco_sock_timeout);

hcon->sco_data = conn; conn->hcon = hcon; @@ -196,11 +197,11 @@ static void sco_conn_del(struct hci_conn *hcon, int err) sco_chan_del(sk, err); bh_unlock_sock(sk); sock_put(sk); - - /* Ensure no more work items will run before freeing conn. */ - cancel_delayed_work_sync(&conn->timeout_work); }

+ /* Ensure no more work items will run before freeing conn. */ + cancel_delayed_work_sync(&conn->timeout_work); + hcon->sco_data = NULL; kfree(conn); } @@ -213,8 +214,6 @@ static void __sco_chan_add(struct sco_conn *conn, struct sock *sk, sco_pi(sk)->conn = conn; conn->sk = sk;

- INIT_DELAYED_WORK(&conn->timeout_work, sco_sock_timeout); - if (parent) bt_accept_enqueue(parent, sk, true); }

From: Linus Walleij linus.walleij@linaro.org

[ Upstream commit 5f5f12f5d4b108399130bb5c11f07765851d9cdb ]

The max VLAN number with non-4K VLAN activated is 15, and the range is 0..15. Not 16.

The impact should be low since we by default have 4K VLAN and thus have 4095 VLANs to play with in this switch. There will not be a problem unless the code is rewritten to only use 16 VLANs.

Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Cc: Mauri Sandberg sandberg@mailfence.com Cc: DENG Qingfang dqfext@gmail.com Cc: Florian Fainelli f.fainelli@gmail.com Reviewed-by: Alvin Šipraga alsi@bang-olufsen.dk Reviewed-by: Vladimir Oltean olteanv@gmail.com Signed-off-by: Linus Walleij linus.walleij@linaro.org Reviewed-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/dsa/rtl8366rb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/dsa/rtl8366rb.c b/drivers/net/dsa/rtl8366rb.c index 5aefd7a4696a5..87832e36c3d5a 100644 --- a/drivers/net/dsa/rtl8366rb.c +++ b/drivers/net/dsa/rtl8366rb.c @@ -1265,7 +1265,7 @@ static int rtl8366rb_set_mc_index(struct realtek_smi *smi, int port, int index)

static bool rtl8366rb_is_vlan_valid(struct realtek_smi *smi, unsigned int vlan) { - unsigned int max = RTL8366RB_NUM_VLANS; + unsigned int max = RTL8366RB_NUM_VLANS - 1;

if (smi->vlan4k_enabled) max = RTL8366RB_NUM_VIDS - 1;

From: Pavel Skripkin paskripkin@gmail.com

[ Upstream commit 2c98b8a3458df03abdc6945bbef67ef91d181938 ]

If em28xx dev has ->dev_next pointer, we need to delete ->dev_next list node from em28xx_extension_devlist on disconnect to avoid UAF bugs and corrupted list bugs, since driver frees this pointer on disconnect.

Reported-and-tested-by: syzbot+a6969ef522a36d3344c9@syzkaller.appspotmail.com

Fixes: 1a23f81b7dc3 ("V4L/DVB (9979): em28xx: move usb probe code to a proper place") Signed-off-by: Pavel Skripkin paskripkin@gmail.com Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/usb/em28xx/em28xx-cards.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/media/usb/em28xx/em28xx-cards.c b/drivers/media/usb/em28xx/em28xx-cards.c index 3f59a98dbf9a1..ec608f60d2c75 100644 --- a/drivers/media/usb/em28xx/em28xx-cards.c +++ b/drivers/media/usb/em28xx/em28xx-cards.c @@ -4030,8 +4030,11 @@ static void em28xx_usb_disconnect(struct usb_interface *intf)

em28xx_close_extension(dev);

- if (dev->dev_next) + if (dev->dev_next) { + em28xx_close_extension(dev->dev_next); em28xx_release_resources(dev->dev_next); + } + em28xx_release_resources(dev);

if (dev->dev_next) {

From: Christophe JAILLET christophe.jaillet@wanadoo.fr

[ Upstream commit 2143ad413c05c7be24c3a92760e367b7f6aaac92 ]

A successful 'clk_prepare()' call should be balanced by a corresponding 'clk_unprepare()' call in the error handling path of the probe, as already done in the remove function.

Update the error handling path accordingly.

Fixes: 3003a180ef6b ("[media] VPU: mediatek: support Mediatek VPU") Signed-off-by: Christophe JAILLET christophe.jaillet@wanadoo.fr Reviewed-by: Houlong Wei houlong.wei@mediatek.com Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/platform/mtk-vpu/mtk_vpu.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/mtk-vpu/mtk_vpu.c b/drivers/media/platform/mtk-vpu/mtk_vpu.c index f8d35e3ac1dcc..9b57fb2857285 100644 --- a/drivers/media/platform/mtk-vpu/mtk_vpu.c +++ b/drivers/media/platform/mtk-vpu/mtk_vpu.c @@ -818,7 +818,8 @@ static int mtk_vpu_probe(struct platform_device *pdev) vpu->wdt.wq = create_singlethread_workqueue("vpu_wdt"); if (!vpu->wdt.wq) { dev_err(dev, "initialize wdt workqueue failed\n"); - return -ENOMEM; + ret = -ENOMEM; + goto clk_unprepare; } INIT_WORK(&vpu->wdt.ws, vpu_wdt_reset_func); mutex_init(&vpu->vpu_mutex); @@ -917,6 +918,8 @@ disable_vpu_clk: vpu_clock_disable(vpu); workqueue_destroy: destroy_workqueue(vpu->wdt.wq); +clk_unprepare: + clk_unprepare(vpu->clk);

return ret; }

From: Colin Ian King colin.king@canonical.com

[ Upstream commit 7266dda2f1dfe151b12ef0c14eb4d4e622fb211c ]

Currently a call to snd_card_new that fails will set card with a NULL pointer, this causes a null pointer dereference on the error cleanup path when card it passed to snd_card_free. Fix this by adding a new error exit path that does not call snd_card_free and exiting via this new path.

Addresses-Coverity: ("Explicit null dereference")

Fixes: 9e44d63246a9 ("[media] cx23885: Add ALSA support") Signed-off-by: Colin Ian King colin.king@canonical.com Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/pci/cx23885/cx23885-alsa.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/media/pci/cx23885/cx23885-alsa.c b/drivers/media/pci/cx23885/cx23885-alsa.c index db1e8ff35474a..150106eb36052 100644 --- a/drivers/media/pci/cx23885/cx23885-alsa.c +++ b/drivers/media/pci/cx23885/cx23885-alsa.c @@ -559,7 +559,7 @@ struct cx23885_audio_dev *cx23885_audio_register(struct cx23885_dev *dev) SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1, THIS_MODULE, sizeof(struct cx23885_audio_dev), &card); if (err < 0) - goto error; + goto error_msg;

chip = (struct cx23885_audio_dev *) card->private_data; chip->dev = dev; @@ -585,6 +585,7 @@ struct cx23885_audio_dev *cx23885_audio_register(struct cx23885_dev *dev)

error: snd_card_free(card); +error_msg: pr_err("%s(): Failed to register analog audio adapter\n", __func__);

From: Colin Ian King colin.king@canonical.com

[ Upstream commit 51fa3b70d27342baf1ea8aaab3e96e5f4f26d5b2 ]

The call to ops->suspend for the dev->dev_next case can currently trigger a call on a null function pointer if ops->suspend is null. Skip over the use of function ops->suspend if it is null.

Addresses-Coverity: ("Dereference after null check")

Fixes: be7fd3c3a8c5 ("media: em28xx: Hauppauge DualHD second tuner functionality") Signed-off-by: Colin Ian King colin.king@canonical.com Signed-off-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/usb/em28xx/em28xx-core.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/media/usb/em28xx/em28xx-core.c b/drivers/media/usb/em28xx/em28xx-core.c index d0f95a5cb4d23..437651307056f 100644 --- a/drivers/media/usb/em28xx/em28xx-core.c +++ b/drivers/media/usb/em28xx/em28xx-core.c @@ -1151,8 +1151,9 @@ int em28xx_suspend_extension(struct em28xx *dev) dev_info(&dev->intf->dev, "Suspending extensions\n"); mutex_lock(&em28xx_devlist_mutex); list_for_each_entry(ops, &em28xx_extension_devlist, next) { - if (ops->suspend) - ops->suspend(dev); + if (!ops->suspend) + continue; + ops->suspend(dev); if (dev->dev_next) ops->suspend(dev->dev_next); }

From: Evgeny Novikov novikov@ispras.ru

[ Upstream commit 69a10678e2fba3d182e78ea041f2d1b1a6058764 ]

mn88443x_cmn_power_on() did not handle possible errors of clk_prepare_enable() and always finished successfully so that its caller mn88443x_probe() did not care about failed preparing/enabling of clocks as well.

Add missed error handling in both mn88443x_cmn_power_on() and mn88443x_probe(). This required to change the return value of the former from "void" to "int".

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 0f408ce8941f ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver") Signed-off-by: Evgeny Novikov novikov@ispras.ru Co-developed-by: Kirill Shilimanov kirill.shilimanov@huawei.com Signed-off-by: Kirill Shilimanov kirill.shilimanov@huawei.com Signed-off-by: Sean Young sean@mess.org Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/media/dvb-frontends/mn88443x.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/media/dvb-frontends/mn88443x.c b/drivers/media/dvb-frontends/mn88443x.c index 9ec1aeef03d5a..53981ff9422e0 100644 --- a/drivers/media/dvb-frontends/mn88443x.c +++ b/drivers/media/dvb-frontends/mn88443x.c @@ -204,11 +204,18 @@ struct mn88443x_priv { struct regmap *regmap_t; };

-static void mn88443x_cmn_power_on(struct mn88443x_priv *chip) +static int mn88443x_cmn_power_on(struct mn88443x_priv *chip) { + struct device *dev = &chip->client_s->dev; struct regmap *r_t = chip->regmap_t; + int ret;

- clk_prepare_enable(chip->mclk); + ret = clk_prepare_enable(chip->mclk); + if (ret) { + dev_err(dev, "Failed to prepare and enable mclk: %d\n", + ret); + return ret; + }

gpiod_set_value_cansleep(chip->reset_gpio, 1); usleep_range(100, 1000); @@ -222,6 +229,8 @@ static void mn88443x_cmn_power_on(struct mn88443x_priv *chip) } else { regmap_write(r_t, HIZSET3, 0x8f); } + + return 0; }

static void mn88443x_cmn_power_off(struct mn88443x_priv *chip) @@ -738,7 +747,10 @@ static int mn88443x_probe(struct i2c_client *client, chip->fe.demodulator_priv = chip; i2c_set_clientdata(client, chip);

- mn88443x_cmn_power_on(chip); + ret = mn88443x_cmn_power_on(chip); + if (ret) + goto err_i2c_t; + mn88443x_s_sleep(chip); mn88443x_t_sleep(chip);

From: Giovanni Cabiddu giovanni.cabiddu@intel.com

[ Upstream commit 18fcba469ba5359c1de7e3fb16f7b9e8cd1b8e02 ]

Upon receiving a PFVF message, check if the interrupt bit is set in the message. If it is not, that means that the interrupt was probably triggered by a collision. In this case, disregard the message and re-enable the interrupts.

Fixes: ed8ccaef52fa ("crypto: qat - Add support for SRIOV") Signed-off-by: Giovanni Cabiddu giovanni.cabiddu@intel.com Reviewed-by: Marco Chiappero marco.chiappero@intel.com Signed-off-by: Herbert Xu herbert@gondor.apana.org.au Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/crypto/qat/qat_common/adf_pf2vf_msg.c | 6 ++++++ drivers/crypto/qat/qat_common/adf_vf_isr.c | 6 ++++++ 2 files changed, 12 insertions(+)

diff --git a/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c b/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c index 72fd2bbbe704e..180016e157771 100644 --- a/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c +++ b/drivers/crypto/qat/qat_common/adf_pf2vf_msg.c @@ -250,6 +250,11 @@ void adf_vf2pf_req_hndl(struct adf_accel_vf_info *vf_info)

/* Read message from the VF */ msg = ADF_CSR_RD(pmisc_addr, hw_data->get_pf2vf_offset(vf_nr)); + if (!(msg & ADF_VF2PF_INT)) { + dev_info(&GET_DEV(accel_dev), + "Spurious VF2PF interrupt, msg %X. Ignored\n", msg); + goto out; + }

/* To ACK, clear the VF2PFINT bit */ msg &= ~ADF_VF2PF_INT; @@ -333,6 +338,7 @@ void adf_vf2pf_req_hndl(struct adf_accel_vf_info *vf_info) if (resp && adf_iov_putmsg(accel_dev, resp, vf_nr)) dev_err(&GET_DEV(accel_dev), "Failed to send response to VF\n");

+out: /* re-enable interrupt on PF from this VF */ adf_enable_vf2pf_interrupts(accel_dev, (1 << vf_nr)); return; diff --git a/drivers/crypto/qat/qat_common/adf_vf_isr.c b/drivers/crypto/qat/qat_common/adf_vf_isr.c index ef90902c8200d..86274e3c6781d 100644 --- a/drivers/crypto/qat/qat_common/adf_vf_isr.c +++ b/drivers/crypto/qat/qat_common/adf_vf_isr.c @@ -123,6 +123,11 @@ static void adf_pf2vf_bh_handler(void *data)

/* Read the message from PF */ msg = ADF_CSR_RD(pmisc_bar_addr, hw_data->get_pf2vf_offset(0)); + if (!(msg & ADF_PF2VF_INT)) { + dev_info(&GET_DEV(accel_dev), + "Spurious PF2VF interrupt, msg %X. Ignored\n", msg); + goto out; + }

if (!(msg & ADF_PF2VF_MSGORIGIN_SYSTEM)) /* Ignore legacy non-system (non-kernel) PF2VF messages */ @@ -171,6 +176,7 @@ static void adf_pf2vf_bh_handler(void *data) msg &= ~ADF_PF2VF_INT; ADF_CSR_WR(pmisc_bar_addr, hw_data->get_pf2vf_offset(0), msg);

+out: /* Re-enable PF2VF interrupts */ adf_enable_pf2vf_interrupts(accel_dev); return;

From: Dan Carpenter dan.carpenter@oracle.com

[ Upstream commit c1c8380b0320ab757e60ed90efc8b1992a943256 ]

The problem is that "channel" is an unsigned int, when it's less 5 the value of "channel - 5" is not a negative number as one would expect but is very high positive value instead.

This means that "start" becomes a very high positive value. The result of that is that we never enter the "for (i = start; i <= end; i++) {" loop. Instead of storing the result from b43legacy_radio_aci_detect() it just uses zero.

Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices") Signed-off-by: Dan Carpenter dan.carpenter@oracle.com Acked-by: Michael Büsch m@bues.ch Signed-off-by: Kalle Valo kvalo@codeaurora.org Link: https://lore.kernel.org/r/20211006073542.GD8404@kili Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/net/wireless/broadcom/b43legacy/radio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/broadcom/b43legacy/radio.c b/drivers/net/wireless/broadcom/b43legacy/radio.c index eab1c93878468..8f845db23766b 100644 --- a/drivers/net/wireless/broadcom/b43legacy/radio.c +++ b/drivers/net/wireless/broadcom/b43legacy/radio.c @@ -299,7 +299,7 @@ u8 b43legacy_radio_aci_scan(struct b43legacy_wldev *dev) & 0x7FFF); b43legacy_set_all_gains(dev, 3, 8, 1);

- start = (channel - 5 > 0) ? channel - 5 : 1; + start = (channel > 5) ? channel - 5 : 1; end = (channel + 5 < 14) ? channel + 5 : 13;

for (i = start; i <= end; i++) {

From: Tony Lindgren tony@atomide.com

[ Upstream commit 8e0e7bd38b1ec7f9e5d18725ad41828be4e09859 ]

If sdhci-omap is configured for an unused device instance and the device is not set as disabled, we can get a NULL pointer dereference:

Unable to handle kernel NULL pointer dereference at virtual address 00000045 ... (regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0) (mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490) (sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160) (sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154) (mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c) (mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c) (mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c) (__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c) (sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)

AFAIK we are not seeing this with the devices configured in the mainline kernel but this can cause issues for folks bringing up their boards.

Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver") Signed-off-by: Tony Lindgren tony@atomide.com Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/mmc/host/sdhci-omap.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c index 05ade7a2dd243..f5bff9e710fb2 100644 --- a/drivers/mmc/host/sdhci-omap.c +++ b/drivers/mmc/host/sdhci-omap.c @@ -690,7 +690,8 @@ static void sdhci_omap_set_power(struct sdhci_host *host, unsigned char mode, { struct mmc_host *mmc = host->mmc;

- mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); + if (!IS_ERR(mmc->supply.vmmc)) + mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); }

static int sdhci_omap_enable_dma(struct sdhci_host *host)

From: Dan Carpenter dan.carpenter@oracle.com

[ Upstream commit beae4a6258e64af609ad5995cc6b6056eb0d898e ]

The "msh" pointer is device managed, meaning that memstick_alloc_host() calls device_initialize() on it. That means that it can't be free using kfree() but must instead be freed with memstick_free_host(). Otherwise it leads to a tiny memory leak of device resources.

Fixes: 60fdd931d577 ("memstick: add support for JMicron jmb38x MemoryStick host controller") Signed-off-by: Dan Carpenter dan.carpenter@oracle.com Link: https://lore.kernel.org/r/20211011123912.GD15188@kili Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/memstick/host/jmb38x_ms.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/memstick/host/jmb38x_ms.c b/drivers/memstick/host/jmb38x_ms.c index 29f5021d21ea6..0610d3c9f1318 100644 --- a/drivers/memstick/host/jmb38x_ms.c +++ b/drivers/memstick/host/jmb38x_ms.c @@ -907,7 +907,7 @@ static struct memstick_host *jmb38x_ms_alloc_host(struct jmb38x_ms *jm, int cnt)

iounmap(host->addr); err_out_free: - kfree(msh); + memstick_free_host(msh); return NULL; }

From: Zev Weiss zev@bewilderbeest.net

[ Upstream commit b7931a7b0e0df4d2a25fedd895ad32c746b77bc1 ]

Maintaining this manually is error prone (there are currently only five chips supported, not six); gcc can do it for us automatically.

Signed-off-by: Zev Weiss zev@bewilderbeest.net Fixes: 666c14906b49 ("hwmon: (pmbus/lm25066) Drop support for LM25063") Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net Signed-off-by: Guenter Roeck linux@roeck-us.net Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/hwmon/pmbus/lm25066.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/hwmon/pmbus/lm25066.c b/drivers/hwmon/pmbus/lm25066.c index 6eafcbb75dcd9..e25b801490862 100644 --- a/drivers/hwmon/pmbus/lm25066.c +++ b/drivers/hwmon/pmbus/lm25066.c @@ -60,7 +60,7 @@ struct __coeff { #define PSC_CURRENT_IN_L (PSC_NUM_CLASSES) #define PSC_POWER_L (PSC_NUM_CLASSES + 1)

-static struct __coeff lm25066_coeff[6][PSC_NUM_CLASSES + 2] = { +static struct __coeff lm25066_coeff[][PSC_NUM_CLASSES + 2] = { [lm25056] = { [PSC_VOLTAGE_IN] = { .m = 16296,

From: Dan Carpenter dan.carpenter@oracle.com

[ Upstream commit 2203bd0e5c12ffc53ffdd4fbd7b12d6ba27e0424 ]

The msm_gem_new_impl() function cleans up after itself so there is no need to call drm_gem_object_put(). Conceptually, it does not make sense to call a kref_put() function until after the reference counting has been initialized which happens immediately after this call in the drm_gem_(private_)object_init() functions.

In the msm_gem_import() function the "obj" pointer is uninitialized, so it will lead to a crash.

Fixes: 05b849111c07 ("drm/msm: prime support") Signed-off-by: Dan Carpenter dan.carpenter@oracle.com Link: https://lore.kernel.org/r/20211013081315.GG6010@kili Signed-off-by: Rob Clark robdclark@chromium.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/gpu/drm/msm/msm_gem.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/msm/msm_gem.c b/drivers/gpu/drm/msm/msm_gem.c index 7c0b30c955c39..c551d84444976 100644 --- a/drivers/gpu/drm/msm/msm_gem.c +++ b/drivers/gpu/drm/msm/msm_gem.c @@ -965,7 +965,7 @@ static struct drm_gem_object *_msm_gem_new(struct drm_device *dev,

ret = msm_gem_new_impl(dev, size, flags, NULL, &obj, struct_mutex_locked); if (ret) - goto fail; + return ERR_PTR(ret);