The patch below does not apply to the 6.12-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to stable@vger.kernel.org.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.12.y git checkout FETCH_HEAD git cherry-pick -x 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f # <resolve conflicts, build, test, etc.> git commit -s git send-email --to 'stable@vger.kernel.org' --in-reply-to '2025021015-endowment-ungraded-dbc0@gregkh' --subject-prefix 'PATCH 6.12.y' HEAD^..

Possible dependencies:

thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 651dee03696e1dfde6d9a7e8664bbdcd9a10ea7f Mon Sep 17 00:00:00 2001 From: Claudiu Beznea claudiu.beznea.uj@bp.renesas.com Date: Thu, 16 Jan 2025 20:22:49 +0200 Subject: [PATCH] serial: sh-sci: Increment the runtime usage counter for the earlycon device

In the sh-sci driver, serial ports are mapped to the sci_ports[] array, with earlycon mapped at index zero.

The uart_add_one_port() function eventually calls __device_attach(), which, in turn, calls pm_request_idle(). The identified code path is as follows:

uart_add_one_port() -> serial_ctrl_register_port() -> serial_core_register_port() -> serial_core_port_device_add() -> serial_base_port_add() -> device_add() -> bus_probe_device() -> device_initial_probe() -> __device_attach() -> // ... if (dev->p->dead) { // ... } else if (dev->driver) { // ... } else { // ... pm_request_idle(dev); // ... }

The earlycon device clocks are enabled by the bootloader. However, the pm_request_idle() call in __device_attach() disables the SCI port clocks while earlycon is still active.

The earlycon write function, serial_console_write(), calls sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to remain unset indefinitely, causing the while loop in sci_poll_put_char() to never exit. On single-core SoCs, this can result in the system being blocked during boot when this issue occurs.

To resolve this, increment the runtime PM usage counter for the earlycon SCI device before registering the UART port.

Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support") Cc: stable@vger.kernel.org Signed-off-by: Claudiu Beznea claudiu.beznea.uj@bp.renesas.com Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.rene... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index e64d59888ecd..b1ea48f38248 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -3436,6 +3436,22 @@ static int sci_probe_single(struct platform_device *dev, }

if (sci_uart_earlycon && sci_ports[0].port.mapbase == sci_res->start) { + /* + * In case: + * - this is the earlycon port (mapped on index 0 in sci_ports[]) and + * - it now maps to an alias other than zero and + * - the earlycon is still alive (e.g., "earlycon keep_bootcon" is + * available in bootargs) + * + * we need to avoid disabling clocks and PM domains through the runtime + * PM APIs called in __device_attach(). For this, increment the runtime + * PM reference counter (the clocks and PM domains were already enabled + * by the bootloader). Otherwise the earlycon may access the HW when it + * has no clocks enabled leading to failures (infinite loop in + * sci_poll_put_char()). + */ + pm_runtime_get_noresume(&dev->dev); + /* * Skip cleanup the sci_port[0] in early_console_exit(), this * port is the same as the earlycon one.