Hi there,
I hope you're doing good.
Would you be interested in Xero users Database?
Please let me know your interest so that I'll get back with count and pricing for your review.
I will be looking forward for your response on this.
Best Regards,
Sophia Martinez
Demand Generation Specialist
To stop receiving emails, respond with Leave out.
From: Aradhya Bhatia <a-bhatia1(a)ti.com>
Once the DSI Link and DSI Phy are initialized, the code needs to wait
for Clk and Data Lanes to be ready, before continuing configuration.
This is in accordance with the DSI Start-up procedure, found in the
Technical Reference Manual of Texas Instrument's J721E SoC[0] which
houses this DSI TX controller.
If the previous bridge (or crtc/encoder) are configured pre-maturely,
the input signal FIFO gets corrupt. This introduces a color-shift on the
display.
Allow the driver to wait for the clk and data lanes to get ready during
DSI enable.
[0]: See section 12.6.5.7.3 "Start-up Procedure" in J721E SoC TRM
TRM Link: http://www.ti.com/lit/pdf/spruil1
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable(a)vger.kernel.org
Tested-by: Dominik Haller <d.haller(a)phytec.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1(a)ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia(a)linux.dev>
---
drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c | 15 ++++++++++++++-
1 file changed, 14 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
index 87921a748cdb..6a77ca36cb9d 100644
--- a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
+++ b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
@@ -769,7 +769,7 @@ static void cdns_dsi_bridge_enable(struct drm_bridge *bridge)
struct phy_configure_opts_mipi_dphy *phy_cfg = &output->phy_opts.mipi_dphy;
unsigned long tx_byte_period;
struct cdns_dsi_cfg dsi_cfg;
- u32 tmp, reg_wakeup, div;
+ u32 tmp, reg_wakeup, div, status;
int nlanes;
if (WARN_ON(pm_runtime_get_sync(dsi->base.dev) < 0))
@@ -786,6 +786,19 @@ static void cdns_dsi_bridge_enable(struct drm_bridge *bridge)
cdns_dsi_hs_init(dsi);
cdns_dsi_init_link(dsi);
+ /*
+ * Now that the DSI Link and DSI Phy are initialized,
+ * wait for the CLK and Data Lanes to be ready.
+ */
+ tmp = CLK_LANE_RDY;
+ for (int i = 0; i < nlanes; i++)
+ tmp |= DATA_LANE_RDY(i);
+
+ if (readl_poll_timeout(dsi->regs + MCTL_MAIN_STS, status,
+ (tmp == (status & tmp)), 100, 500000))
+ dev_err(dsi->base.dev,
+ "Timed Out: DSI-DPhy Clock and Data Lanes not ready.\n");
+
writel(HBP_LEN(dsi_cfg.hbp) | HSA_LEN(dsi_cfg.hsa),
dsi->regs + VID_HSIZE1);
writel(HFP_LEN(dsi_cfg.hfp) | HACT_LEN(dsi_cfg.hact),
--
2.34.1
From: Aradhya Bhatia <a-bhatia1(a)ti.com>
The crtc_* mode parameters do not get generated (duplicated in this
case) from the regular parameters before the mode validation phase
begins.
The rest of the code conditionally uses the crtc_* parameters only
during the bridge enable phase, but sticks to the regular parameters
for mode validation. In this singular instance, however, the driver
tries to use the crtc_clock parameter even during the mode validation,
causing the validation to fail.
Allow the D-Phy config checks to use mode->clock instead of
mode->crtc_clock during mode_valid checks, like everywhere else in the
driver.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable(a)vger.kernel.org
Reviewed-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov(a)linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1(a)ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia(a)linux.dev>
---
drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
index b0a1a6774ea6..19cc8734a4c8 100644
--- a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
+++ b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
@@ -568,13 +568,14 @@ static int cdns_dsi_check_conf(struct cdns_dsi *dsi,
struct phy_configure_opts_mipi_dphy *phy_cfg = &output->phy_opts.mipi_dphy;
unsigned long dsi_hss_hsa_hse_hbp;
unsigned int nlanes = output->dev->lanes;
+ int mode_clock = (mode_valid_check ? mode->clock : mode->crtc_clock);
int ret;
ret = cdns_dsi_mode2cfg(dsi, mode, dsi_cfg, mode_valid_check);
if (ret)
return ret;
- phy_mipi_dphy_get_default_config(mode->crtc_clock * 1000,
+ phy_mipi_dphy_get_default_config(mode_clock * 1000,
mipi_dsi_pixel_format_to_bpp(output->dev->format),
nlanes, phy_cfg);
--
2.34.1
From: Aradhya Bhatia <a-bhatia1(a)ti.com>
The driver code doesn't have a Phy de-initialization path as yet, and so
it does not clear the phy_initialized flag while suspending. This is a
problem because after resume the driver looks at this flag to determine
if a Phy re-initialization is required or not. It is in fact required
because the hardware is resuming from a suspend, but the driver does not
carry out any re-initialization causing the D-Phy to not work at all.
Call the counterparts of phy_init() and phy_power_on(), that are
phy_exit() and phy_power_off(), from _bridge_post_disable(), and clear
the flags so that the Phy can be initialized again when required.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable(a)vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov(a)linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1(a)ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia(a)linux.dev>
---
drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
index 2f897ea5e80a..b0a1a6774ea6 100644
--- a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
+++ b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
@@ -680,6 +680,11 @@ static void cdns_dsi_bridge_post_disable(struct drm_bridge *bridge)
struct cdns_dsi_input *input = bridge_to_cdns_dsi_input(bridge);
struct cdns_dsi *dsi = input_to_dsi(input);
+ dsi->phy_initialized = false;
+ dsi->link_initialized = false;
+ phy_power_off(dsi->dphy);
+ phy_exit(dsi->dphy);
+
pm_runtime_put(dsi->base.dev);
}
@@ -1152,7 +1157,6 @@ static int __maybe_unused cdns_dsi_suspend(struct device *dev)
clk_disable_unprepare(dsi->dsi_sys_clk);
clk_disable_unprepare(dsi->dsi_p_clk);
reset_control_assert(dsi->dsi_p_rst);
- dsi->link_initialized = false;
return 0;
}
--
2.34.1
From: Aradhya Bhatia <a-bhatia1(a)ti.com>
Fix the OF node pointer passed to the of_drm_find_bridge() call to find
the next bridge in the display chain.
The code to find the next panel (and create its panel-bridge) works
fine, but to find the next (non-panel) bridge does not.
To find the next bridge in the pipeline, we need to pass "np" - the OF
node pointer of the next entity in the devicetree chain. Passing
"of_node" to of_drm_find_bridge (which is what the code does currently)
will fetch the bridge for the cdns-dsi which is not what's required.
Fix that.
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable(a)vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov(a)linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen(a)ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1(a)ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia(a)linux.dev>
---
drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
index c7a0247e06ad..2f897ea5e80a 100644
--- a/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
+++ b/drivers/gpu/drm/bridge/cadence/cdns-dsi-core.c
@@ -952,7 +952,7 @@ static int cdns_dsi_attach(struct mipi_dsi_host *host,
bridge = drm_panel_bridge_add_typed(panel,
DRM_MODE_CONNECTOR_DSI);
} else {
- bridge = of_drm_find_bridge(dev->dev.of_node);
+ bridge = of_drm_find_bridge(np);
if (!bridge)
bridge = ERR_PTR(-EINVAL);
}
--
2.34.1
If a userptr vma subject to prefetching was already invalidated
or invalidated during the prefetch operation, the operation would
repeatedly return -EAGAIN which would typically cause an infinite
loop.
Validate the userptr to ensure this doesn't happen.
Fixes: 5bd24e78829a ("drm/xe/vm: Subclass userptr vmas")
Fixes: 617eebb9c480 ("drm/xe: Fix array of binds")
Cc: Matthew Brost <matthew.brost(a)intel.com>
Cc: <stable(a)vger.kernel.org> # v6.9+
Suggested-by: Matthew Brost <matthew.brost(a)intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom(a)linux.intel.com>
---
drivers/gpu/drm/xe/xe_vm.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/xe/xe_vm.c b/drivers/gpu/drm/xe/xe_vm.c
index 996000f2424e..4c1ca47667ad 100644
--- a/drivers/gpu/drm/xe/xe_vm.c
+++ b/drivers/gpu/drm/xe/xe_vm.c
@@ -2307,7 +2307,14 @@ static int vm_bind_ioctl_ops_parse(struct xe_vm *vm, struct drm_gpuva_ops *ops,
}
case DRM_GPUVA_OP_UNMAP:
case DRM_GPUVA_OP_PREFETCH:
- /* FIXME: Need to skip some prefetch ops */
+ vma = gpuva_to_vma(op->base.prefetch.va);
+
+ if (xe_vma_is_userptr(vma)) {
+ err = xe_vma_userptr_pin_pages(to_userptr_vma(vma));
+ if (err)
+ return err;
+ }
+
xe_vma_ops_incr_pt_update_ops(vops, op->tile_mask);
break;
default:
--
2.48.1
At the 'fail2' label in hd44780_probe(), the 'lcd' variable is
freed via kfree(), but this does not actually release the memory
allocated by charlcd_alloc(), as that memory is a container for lcd.
As a result, a memory leak occurs. Replace kfree() with charlcd_free()
to fix a potential memory leak.
Same replacement is done in hd44780_remove().
Fixes: 718e05ed92ec ("auxdisplay: Introduce hd44780_common.[ch]")
Cc: stable(a)vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024(a)163.com>
---
Changes in v3:
- modify the patch description.
Thanks for the review! I think Fixes-tag should be added because
the previous version causes a memory leak. I modified the patch
description to illustrate it. Thanks again!
Changes in v2:
- Merge the two patches into one.
- Modify the patch description.
Sorry Geert, I didn't see your reply until after I sent the
second patch. I've merged the two patches into one, hoping
to make your work a bit easier! Thanks a lot!
---
drivers/auxdisplay/hd44780.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/auxdisplay/hd44780.c b/drivers/auxdisplay/hd44780.c
index 0526f0d90a79..9d0ae9c02e9b 100644
--- a/drivers/auxdisplay/hd44780.c
+++ b/drivers/auxdisplay/hd44780.c
@@ -313,7 +313,7 @@ static int hd44780_probe(struct platform_device *pdev)
fail3:
kfree(hd);
fail2:
- kfree(lcd);
+ charlcd_free(lcd);
fail1:
kfree(hdc);
return ret;
@@ -328,7 +328,7 @@ static void hd44780_remove(struct platform_device *pdev)
kfree(hdc->hd44780);
kfree(lcd->drvdata);
- kfree(lcd);
+ charlcd_free(lcd);
}
static const struct of_device_id hd44780_of_match[] = {
--
2.25.1