From: Mathieu Malaterre malat@debian.org
[ Upstream commit 3e3380d0675d5e20b0af067d60cb947a4348bf9b ]
Improve the DTS files by removing all the leading "0x" and zeros to fix the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f ( -iname *.dts -o -iname *.dtsi ) -exec sed -i -e "s/@([0-9a-fA-FxX.;:#]+)\s*{/@\L\1 {/g" -e "s/@0x(.*) {/@\1 {/g" -e "s/@0+(.*) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved, namely setting unit-address to lower case, and adding a whitespace before the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney ddaney@caviumnetworks.com Suggested-by: Rob Herring robh@kernel.org Signed-off-by: Mathieu Malaterre malat@debian.org [vzapolskiy: fixed commit message to pass checkpatch.pl test] Signed-off-by: Vladimir Zapolskiy vz@mleia.com Signed-off-by: Sasha Levin sashal@kernel.org --- arch/arm/boot/dts/lpc32xx.dtsi | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index b7303a4e4236..ed0d6fb20122 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -230,7 +230,7 @@ status = "disabled"; };
- i2s1: i2s@2009C000 { + i2s1: i2s@2009c000 { compatible = "nxp,lpc3220-i2s"; reg = <0x2009C000 0x1000>; }; @@ -273,7 +273,7 @@ status = "disabled"; };
- i2c1: i2c@400A0000 { + i2c1: i2c@400a0000 { compatible = "nxp,pnx-i2c"; reg = <0x400A0000 0x100>; interrupt-parent = <&sic1>; @@ -284,7 +284,7 @@ clocks = <&clk LPC32XX_CLK_I2C1>; };
- i2c2: i2c@400A8000 { + i2c2: i2c@400a8000 { compatible = "nxp,pnx-i2c"; reg = <0x400A8000 0x100>; interrupt-parent = <&sic1>; @@ -295,7 +295,7 @@ clocks = <&clk LPC32XX_CLK_I2C2>; };
- mpwm: mpwm@400E8000 { + mpwm: mpwm@400e8000 { compatible = "nxp,lpc3220-motor-pwm"; reg = <0x400E8000 0x78>; status = "disabled"; @@ -394,7 +394,7 @@ #gpio-cells = <3>; /* bank, pin, flags */ };
- timer4: timer@4002C000 { + timer4: timer@4002c000 { compatible = "nxp,lpc3220-timer"; reg = <0x4002C000 0x1000>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; @@ -412,7 +412,7 @@ status = "disabled"; };
- watchdog: watchdog@4003C000 { + watchdog: watchdog@4003c000 { compatible = "nxp,pnx4008-wdt"; reg = <0x4003C000 0x1000>; clocks = <&clk LPC32XX_CLK_WDOG>; @@ -451,7 +451,7 @@ status = "disabled"; };
- timer1: timer@4004C000 { + timer1: timer@4004c000 { compatible = "nxp,lpc3220-timer"; reg = <0x4004C000 0x1000>; interrupts = <17 IRQ_TYPE_LEVEL_LOW>; @@ -475,7 +475,7 @@ status = "disabled"; };
- pwm1: pwm@4005C000 { + pwm1: pwm@4005c000 { compatible = "nxp,lpc3220-pwm"; reg = <0x4005C000 0x4>; clocks = <&clk LPC32XX_CLK_PWM1>; @@ -484,7 +484,7 @@ status = "disabled"; };
- pwm2: pwm@4005C004 { + pwm2: pwm@4005c004 { compatible = "nxp,lpc3220-pwm"; reg = <0x4005C004 0x4>; clocks = <&clk LPC32XX_CLK_PWM2>;